Search Documents

By M. R. Shahan, C. E. Seaman, S. E. Mischler, T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce risks of coal dust-fueled explosions. The goal of this NIOSH study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust (<75 µm diameter) in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity. Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing, and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle is operated at high fluid pressures to produce smaller droplets and move more air. These findings can be used to select sprays and design spray arrays to control airborne float dust over the entire longwall ventilated opening. INTRODUCTION Coal mining processes produce airborne dust that naturally deposits on the floor, roof, and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 microns in diameter, are deposited in return entries of coal mines and can be re-entrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; NIOSH, 2006). These particles are also those most likely to participate in coal dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (CFR, 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal dust-fueled explosions. Water sprays are both effective and widely accepted as a method for controlling underground coal mine dust. In fact, water sprays are considered to be the most economical and technically feasible means of reducing dust concentrations in underground coal mines (Courtney and Cheng, 1977; Barker and Humphreys, 1996). Sprays are used in several ways to control dust in mining processes: inhibiting dust formation, immobilizing dust to prevent it from becoming airborne, and capturing airborne dust (Cheng, 1973). Reductions in airborne dust concentrations have frequently been attributed to inertial impaction between water droplets and dust particles, forming larger agglomerates which then quickly precipitate out of the airstream (McPherson, 1993). Inertial impaction activity is generally accepted as the major capture mechanism for airborne particles larger than 0.5 µm in diameter. It is this mechanism that is evaluated in this study."

Jan 1, 2017

By M. R. Shahan, C. E. Seaman, Mischler S. E., T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. IntroductionCoal mining processes produce airborne dust that naturally deposits on the floor, roof and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 µm in diameter, are deposited in the return entries of coal mines and can be reentrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; U.S. National Institute for Occupational Safety and Health (NIOSH), 2006). These particles are also those most likely to participate in coal-dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (U.S. Mine Safety and Health Administration (MSHA), 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal-dust-fueled explosions."

Jan 1, 2018

By E. D. Gardner

This bulletin, which discusses open-cut mining at the metal mines of the United States, is the last of a series of such papers by the Bureau of Mines describing the principal methods of mining.4 Open-cut mining is applicable to flat-lying mineral deposits relatively near the surface. Vein deposits seldom are amenable to this method, although outcrops of veins sometimes are worked as open pits. Most of the iron ore of the country is mined from open pits; according to the Minerals Yearbook, 67.4 percent was mined from open pits and 32.6 percent from underground mines in 1937. Open-cut mining is relatively new in the copper industry but yields more copper than any other method; in 1937 about 52 percent of the copper ore mined in the United States was taken from open pits. Lead-zinc ore has been produced from open pits in the Joplin (Mo.) district, but most of the deposits in this area, although flat-lying, are too deep to be mined economically by the open-cut method. In 1937 one company at Oronogo, Mo., was stripping overburden and mining mixed oxidized and sulfide ores by this method.

Jan 1, 1941

By AIME AIME

THE second meeting of &apos;the Open-Hearth Committee, &apos;sub-division of the Iron and Steel Committee of this Institute, was held at the Hotel Cleveland, Cleveland, Ohio; on Oct. 13-15. On Oct: 12, the Open-Hearth Superintendents visited the plants of the Youngstown Sheet and Tube Co. and. the Republic Iron and Steel Co. These men were courteously entertailled by the two companies and every facility for a thorough inspection was furnished. Luncheon was severed at the plant bf the Youngstown Sheet and Tube Co. The meeting was opened Tuesday morning with addresses by J. V. W. Reynders, President of the Institute, and Herbert M. Boylston, Chairman of the Ohio Section of the Institute. E. A. Whitworth, of the Gathmann Engineering Co., presided at the meeting and L. B. Lindeinuth was secretary.

Jan 1, 1925

THE developments in construction and operation of the basic open-hearth furnace that have taken place in recent years have placed new emphasis on the vital influence played by regulation and control of the combustion system in both furnace production and furnace life. The several factors influencing flame development, such as regulation of fuel supply, air supply, air preheat, furnace draft, and furnace reversal, must be controlled closely if successful furnace performance is to be accomplished. Rugged instrumentation of distinctive design is required to sup- ply dependable information concerning operating conditions, which is requisite to proper regulation of combustion. This chapter attempts to give a practical discussion of the various features of open-hearth practice and instrumentation related to the efficient heating of the furnace, control of temperature, and protection of the furnace structure from accidental overheating. The appended references will be helpful to readers wanting a more detailed treatment of individual topics. OPEN-HEARTH FUELS The most important open-hearth fuels are listed in Table 4-1 together with their compositions and other data useful for combustion calculations. A detailed discussion of open-hearth fuels is not attempted here, but certain factors peculiar to their application to this type of process are briefly indicated on the following pages. Very often an open-hearth shop is forced by economic factors to use a fuel to which its furnaces are not very well adapted, because the general fuel-allocation scheme for the works as a whole seems to demand it. Often a variable marginal supply of coke-oven gas or tar must be consumed by the open hearth, together with another fuel such as producer gas, natural gas, or oil, to fill out total requirements. Most furnaces employ more than one kind of fuel during their useful life; however, the partial redesign

Jan 1, 1964

By Paul T. Allsman, Paul F. Yopes

17.1--CURRENT AND FUTURE STATUS OF SURFACE MINING PAUL T. ALLSMAN AND PAUL F. YOPES 17.1.1--CURRENT The history of surface mining essentially is one of mining coal, copper, iron and aluminum ores, of placer mining gold and tin, and of pits and quarries producing clays, gypsum, phosphate rock, sand, gravel and stone. Table 17-1 is a summary of the estimated world and United States production of crude metallic and non¬metallic ores and coal in 1969. It includes estimates of the quantities produced by surface-mining methods. Two-thirds of the 10 billion tons are mined from the surface, ranging from a third of the coal. 57% of the metallic ores, and nearly all clays, stone, sand and gravel. Production by surface methods in the United States, parallels that of the world with one exception: about 90% of the copper and iron ore is mined from the surface, whereas elsewhere only about half the copper ore is surface mined. In Canada, surface mining of the Athabasca tar-sand deposits is a recent large-scale unique operation. In surface mining of coal and, to a lesser extent, metallic ores, much waste is stripped, but in nonmetallic pits and quarries the ratio between waste and ore usually is small. Assuming that the stripping ratio for surface mining in the

Jan 1, 1973

By B. Denby

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993. The design and scheduling of open pit operations are consistent problems encountered by the surface mining industry. Numerous techniques and algorithms have been developed to assist the mining engineer in the creation of optimum development strategies. Virtually all the practical techniques that have been produced have concentrated on one of the aspects (limit definition or scheduling) at the expense of the other. It has long been recognised, however, that the two activities are intrinsically linked and thus solving either problem independently of the other can only ever produce sub-optimal results as a whole. This has been termed the "circular reasoning problem". It has also been recognised that, for all practical-sized situations, solving both problems simultaneously is virtually impossible using conventional techniques due to the massive size of the search space involved. A technique is presented which is based on a self-learning genetic algorithm, which provides a combined pit limit and extraction schedule simultaneously in order to maximise the NPV (net present value) of the extraction. The theory is developed in two-dimensions and a number of examples of its application are presented. It is proposed that this approach is a highly efficient, heuristic technique offering the potential to transcend the circular reasoning difficulties of separate pit limit and extraction scheduling systems. Extension of the technique into three-dimensions and its application to realistic problem sizes are discussed

Apr 1, 1994

By B. Calver, D. J. M. Farnsworth

"As open-pit operations expanded at Pine Point, hydraulic aquifer evaluation was undertaken to establish the criteria necessary for the design of a feasible dewatering system.The extreme climate of this northern location dictated that the ore zone under extraction be rendered as dry as possible to minimize freezing effects. The design and implementation of such a system necessitated detailed hydraulic evaluation, and the problems that occurred are typical of those inherent in open-pit mining operations in northern areas.The paper describes the problem solution as approached from a mine engineering point of view, with particular reference to the practical aspects of operation and installation. The hydrological analysis used is simple and readily applicable to most open-pit dewatering problems."

Jan 1, 1969

By Bruce E. Grant, Thomas Jancic, Lawrence G. Dykers, Frank Buchella

Principal factors influencing equipment selection can be grouped into five basic categories: tonnage requirements, ore and waste; topography and property line considerations; ore control requirements; physical characteristics of ore and waste; and climatic considerations. Loading, transporting and ground preparation equipment are largely determined by tonnage requirements. Large size equipment is appropriate for a production of about six million tpm, medium size for three million tons and small size for one million tons or less.

Jan 12, 1973

SAFETY in open-pit mining receives a minimum of notoriety, but its significance in profitable and efficient operation is as great as in other methods of mining. Open-pit operators from Arizona, New Mexico, and Mexico, exchanging ideas on safety at a symposium during the recent annual meeting of the Arizona Section, AIME, discovered unanimity of opinion that the successful safety program depended on managerial and supervisory support with the vigorous cooperation of the employes. Safety Organization The operation of a safety program is dependent on the ability of management to project enthusiasm through the company organization. This requires a suitable method of communication to the supervisory and employee levels so as to approach them in a manner that will inspire cooperation. Safety committees comprised of various combinations of managerial, supervisory, and employe personnel are frequently used for this purpose. The open-cut mine of the Chino Division of the Kennecott Copper Corp., Santa Rita, N. Mex., operates its program through management, a full-time safety engineer, and two safety committees, the Departmental and Shops Safety Committee and the Central Safety Committee. The Departmental and Shops Committee consists of one employe from each department and shop and the safety engineer. The selected members serve for a period of one month. This committee meets once a month, the only representative of management being the safety engineer because it is believed that employes will speak more freely when their supervisors are not present. The duties of the committee are to report hazardous conditions and make recommendations, but the committee has no authority to approve or disapprove. The Central Safety Committee is comprised of supervisory personnel from all departments and shops, and one member of each of the five bargaining organizations. Members of this committee are permanent and hold meetings soon after the departmental group to take action on recommendations of the latter. The committee system insures participation of all levels of personnel in the accident-prevention program, thereby stimulating safety consciousness. The New Cornelia branch of the Phelps-Dodge Corp., uses three groups to conduct the safety program; the General Safety Committee, Division Safety Committee, and the operating-unit safety meetings. The unit safety meetings provide for active participation of employes in discussion of various phases of the program. Within these groups vigorous opinions regarding safety are often expressed and the workmen are critical if they recognize a digression from the adopted safe-practice procedures. These monthly discussions give the program vitality. The Division Safety Committee is composed of the division superintendent and the division department heads, and follows an established pattern in discussion of all phases of the safety program. The General Safety Committee, made up of the manager, division, and department heads, makes decisions on policies and procedures; it renders decisions on recommendations and suggestions. Management at the New Cornelia branch feels this system of safety committees and meetings has been active in advancing the program. Safety Codes In the open-pit mines of the Southwest, a safety code for operation or service of equipment, methods

Jan 1, 1952

By Josiah Pohl, Christopher Utter, Kyle Everly, Akshay Chowdu

Battery Electric Vehicles offer increased energy efficiency for open-pit load & haul operations at a potentially lower overall carbon cost. Electrifying a mine’s fleet, however, presents a unique set of operational challenges. In this study, we explore the effects of electrification on productivity at real operations using a Discrete Event Simulator. The model can simulate multiple shifts, a mixed fleet of diesel and electric trucks, charging and refueling stations, trolley systems, and accurate shovel-truck loading cycles. This study helps determine the trade-offs of adopting electric fleets and how they interact with the layout of today's mines.

Jun 25, 2023

By Matthew Deutsch

A common casualty of modern open-pit mine optimization is the assurance that the resulting design is actually achievable. Optimized mine plans that consider value and a bare minimum of precedence constraints do not, in general, translate into practical, operational mine designs that can be used in the field. Ultimate pits may come to a sharp point at the bottom. Schedules may require taking small parcels of material from many disparate areas of the pit in a single period, and grade control polygons may be ragged, narrow, and not minable with realistic equipment. In this paper, all of these problems are addressed by encoding these three fundamental open-pit mine optimization problems as maximum satisfiability problems. Maximum satisfiability provides a useful framework for problems that are non-linear and may guarantee the optimality that metaheuristics cannot.

By L. E. Fish, G. S. Wyman

CHUQUICAMATA open-pit mine is capable of producing a total of 105,000 tons daily. When the sulphide plant is operating to capacity the distribution of this quantity will be approximately 30,000 tons sulphide ore, 30,000 tons oxide ore and 45,000 tons of waste. At that time the combined capacity of the oxide and sulphide plants will be about 540 million lb of copper per year. Twenty one benches have been opened to date and all are still active except the three top ones at the northeastern limit of the pit. These have been pushed back to final slope line. The pit is 8850 ft long, 3540 ft wide and 980 ft deep. Benches are not all developed to a standard height as the large development shovels used in cutting new benches have been of different size and range. At this time new benches 521 ft high are being developed with an&apos; 11-yd shovel. Ore haulage through the greater part of the pit operation has been on down grades to the crushing plant. With the opening of bench F-4 in April 1944 the first adverse-grade ore haul was encountered. Of the total tonnage now being mined, 35 pct comes from the four benches that are below the level of the crushing plant yard. Waste had been dumped on the same or nearly the same level as the bench from which it was removed up to the opening of bench F-4. Waste from this and lower levels is hauled to the level of the crusher, yard where it must cross the flow of ore traffic to reach the only available dumping space to the east of the mine. The average ore haul is 3.13 miles one way shovel to crusher, and the average waste haul from that portion handled by railroad is 3.32 miles one way from shovel to waste dump. Waste that is being removed by truck haulage from the upper part of the -mine is hauled an average of 1 mile. Ore loaded by trucks is hauled 3/4 mile to a car loading ramp and then by rail to the crushing plant. Drilling and Blasting There are two types of development for blasting being used: One for opening new benches and the other for bank shooting. The former consists of 9a in. diam churn-drill holes drilled 11.8 ft center to center in rows 10.2 ft apart with the holes staggered in the rows thus giving an equilateral-triangle pattern of 11.8 ft on a side. After the first block, 492 ft long by 71.5 ft wide, is shot in the pattern described above, the cut is advanced by smaller shots consisting of four rows of holes spaced 23 ft center to center with the rows 23 ft apart. These shots are fired in conjunction with side shots in which the holes are drilled 33 ft center to center and 29.5 ft back from the toe, thus squaring up the bank for subsequent shooting. An average bank shot consists of about 60 holes drilled in two rows parallel to the face, 30 holes to

Jan 1, 1952

By V. Gregoire

THE DEVELOPMENT by the Iron Ore Company of Canada of the Quebec-Labrador mining project, which eventually led to &apos;Iron Ore in 1954&apos;, involved, from the start, several distinct undertakings. Among them, the most important were: The construction of a 360-mile railway, linking Knob Lake with Seven Islands. The erection of a railway terminal, and harbour facilities, at Seven Islands itself. The building of an entire townsite at Schefferville (formerly Knob Lake) The construction of two hydroelectric plants; and, finally, The development of a sufficient number of orebodies to enable a production of 10 to 15 million tons of ore a year. Since these phases of the project have already been the subject of previous discussions, this paper will not elaborate further on them but will rather concern itself with a brief outline of the Company&apos;s current mining practices.

Jan 1, 1958

By F. J. West

This paper deals with Jones & Laughlin Steel Corporation's new Adams mine, near Kirkland Lake, Ontario. After a brief discussion of ore structure, type, reserve tonnages, etc., the main body of the paper discusses the establishment of an open-pit limit based on economic considerations. The method used by J & L to arrive at an economically sound open-pit boundary its outlined fully. Physical limitations to open-pit boundaries are mentioned briefly. The paper concludes with a few remarks on the mining equipment in use and on its productivity

Jan 1, 1966

By N. C. Steenkamp

Lightning has been observed in dust clouds following open-pit blasting. It is proposed that the occurrence of this phenomenon is related to the physical composition and characterization of the mineral fines that comprise the bulk of the dust cloud. Silicate minerals, which are susceptible to fine fracturing during blasting, generate the initial charge. This is further enhanced by collisions and friction during the turbulent upcast in the post-blast dust cloud. Varying size fractions result in different rates at which these particles drop out of suspension and create a secondary temperature gradient. This results in the creation of two charged zones and increases the potential of developing a discharge in the form of lightning. The ideal prevailing meteorological conditions need to be windless to minimize the effect of particle dissipation and have sufficient moisture toenhance the potential of generating lightning.

Apr 14, 2024

By Yoginder P. Chugh

Most mines are large producing 0-25 mmt annually. The coal is mine.) at depths ranging from .0-150 m 120-500 ft mining at 300 m .(,1000 ft) depth is anticipated in the future. Single and multiple seams ranging from 3-12 m 10-40 ft) in thickness are mined. Most overburden is unconsolidated and consists of sands, and sandy or silty clays. The stripping ratio (volume of overburden to volume of coal mined) varies from 3-L. The overburden and coal is mined in benches 8-12 m -(24-40ft) high; the high-wall angle is about 45 degrees. Bucket wheel and bucket chain excavators are commonly utilized for overburden and coal removal, Some of the large overburden stripping machines nave capacities. Ranging from 4400-10,000 bank cu ( 6000-14,000 BC) per hour. The overburden from the upper benches is transported around the pit using the trains and belt conveyors. It is deposited in the spoils using large stacker-conveyor systems capable of handling 2550-7300 cu m/hour (7500-10,000 cu yds/hour). The overburden from the bottom two or three benches is transported across the pit using the conveyor bridges which are computer controlled. Conveyor bridges capable of handling overburden up to 60 m (200 ft) high are currently in use; a 60 a (20e ft) high conveyor bridge has a capacity of 85 x 10 cu ( 118 x 10 cu yd) annually. The coal is loaded in the trains directly and shipped to power plants or coke oven plants.

Jan 1, 1980

By J. R. Brett

Utah Development Company (UDC) operates five large opencut coal mines in the Bowen Basin of Central Queensland, Australia. In total, over 20 million tonnes of coking coal are exported annually from the five mines. Typically, the coal seams dip at 5 percent, are 2 to 10 metres thick, and sub-crop some 20 to 40 metres below surface. In the main, the operations are single seam, but multiseam (2, 3 or 4 seams) operations do exist and will form an increasing proportion of the mining activities as depths increase. Draglines are used as the major stripping equipment, highwall depths currently ranging from 20 to 65 metres. Whilst project feasibilities were based on stripping to a 60 metre highwall, it is now proposed to continue opencut mining to depths exceeding 100 metres. This will entail large quantities of prestripping (ahead of the draglines) and overcoming problems associated with steepening seam dips, including haulage of coal from the pits.

Jan 1, 1982

Welcome to Mount Isa- my home city and without doubtthe base for what promises to be the most exciting mineral development yet seen in Australia.Mr. Chairman, it also gives me great pride to representthis area in the Queensland State Parliament as well as being the Minister for Minerals and Energy in the Queensland Government.Mount Isa is now part of the Australian mining industry folklore.It is all what a good mine is all about. It is. all what a good community is all about.

Jan 1, 1993

The basic principles of mineral valuation were recognised and propounded at the beginning of this century and have remained virtually unchanged since then. Valuation is seen as a two part process commencing with a technical examination of the mineral property followed by a manipulation of the results of the technical examination in order to determine the monetary value of the project. A thorough and competent technical examination was seen then and remains now as the essential but not sufficient foundation for reliable valuation. All authors stressed the need to maintain the integrity of the data base and to ensure adequate coverage of all relevant aspects. The monetary valuation process through most of the first half of this century was mainly based on the Hoskold two rate method, derived from the formulae for valuing annuities but modified to provide explicitly for recovery of capital. Though the basic principles of valuation have not changed significantly, the means of implementing the components of the technical examination, the styles of deposits being evaluated and the mechanisms of monetary valuation have changed dramatically. Despite all the technological improvements, however, mineral

Jan 1, 1995