Search Documents

By Chririnos. J.

Ante el desabastecimiento del método de explotación de tajeo abierto ascendente con sostenimiento de puntales, empleado en la mina Algamarca, Cajamarca, se sugirió la aplicación de dos nuevos métodos de explotación: almacenamiento provisional y corte de relleno. El primer método es aplicable en aquellos casos donde las rocas de caja sean consistentes y que la veta uniforme que no sea arcillosa, mientras que el segundo, es factible en aquellos blocks donde las rocas de caja sean poco consistentes. En este sentido, el objetivo del texto es señalar la factibilidad de ambos métodos sobre diversos aspectos de carácter técnico-económico, considerando que el ancho de la explotación sea de 0.94 m, para que la utilidad sea más provechosa.

Nov 20, 1972

By Luisa Perez, Carlos Perea

El método de explotación por subniveles es uno de los más utilizados en operaciones mineras de mediana y gran escala, como es el caso de la minería de zinc en Perú. Para seguir la secuencia de explotación, este método requiere el relleno de los caserones vacíos, como por ejemplo el relleno en pasta, el cual se produce mediante la mezcla del relave producto de la planta concentradora de mineral con un 3.5 % de cemento, con el fin de que dicho relleno actúe como pilares de gran dimensión que aporten el sostenimiento necesario a la mina (0,8 MPa). Sin embargo, esto genera una dilución con el mineral a explotar al momento de avanzar en los tajos aledaños. Por ese motivo, y por la necesidad de lograr la automatización de la operación minera, se decide evaluar el relleno detrítico cementado, evaluación que se realiza mediante el análisis de resistencia, estudios de factibilidad, rendimiento en costos, aumento de productividad y seguridad en la operación. El resultado son valores máximos de resistencia de los pilares de 1,6 MPa, que evitan la dilución y mejoran el porcentaje de recuperación de mineral.

Sep 20, 2019

By Luisa Pérez, Carlos Perea

En el caso de la minería de zinc es común emplear el método de explotación por subniveles, el cual exige rellenar los caserones vacíos, por ejemplo, con una mezcla del relave producto de la planta concentradora de mineral con un 3.5% de cemento, lo que actúa como pilar de sostenimiento de la mina (0.8 MPa). Debido a que al momento de avanzar en los tajos aledaños se producía una dilución con el mineral a explotar y, también, a que era necesario automatizar las operaciones; se decidió evaluar el relleno detrítico cementado, mediante análisis de resistencia, estudios de factibilidad, rendimiento en costos, aumento de productividad y seguridad en la operación. Como resultado, se obtuvieron valores máximos de resistencia de los pilares de 1.6 MPa, lo que evitó la dilución y mejoró el porcentaje de recuperación de mineral.

Jun 30, 2020

By Alberto Pacheco

El presente trabajo es un análisis del sistema de organización del sistema de seguridad a través del modelo Reason de causalidad o de "queso suizo", donde se identifica qué aspectos y decisiones se convierten en un factor condicionante para un accidente y también cómo la organización puede aprender de un accidente perfeccionando sus defensas en un ciclo de mejora continua. De forma que este modelo explica que un accidente es la consecuencia final de una superposición de fallas que va desde la última línea de defensa, pasando por el acto inseguro, la condición insegura, la falla de la supervisión, la falla de la asesoría (seguridad) hasta la falla de la organización. Para solucionar dicho problema, se realiza una gestión del error que incluye una serie de medidas preventivas como descubrir, evaluar y eliminar los factores que producen el error dentro de la fuerza laboral y así desarrollar la realidad intrínseca de la organización contra los errores humanos.

Sep 13, 2001

By Luis Amendola

El presente texto señala el proceso de diagnóstico e implementación de gestión de activos físicos en la producción de las operaciones mineras para aumentar su capacidad, al tiempo que elimina las pérdidas y aumenta la eficiencia en las operaciones. Para ello, se utilizó la metodología 3P+ PAM, donde se establece un punto de partida de forma científica y de negocio para definir cuáles serán las acciones que se deben ejecutar para alcanzar la meta y las buenas prácticas en la gestión de activos físicos de la empresa.

Sep 1, 2014

By Ariel Orellana Wiarco

Para diseñar un sistema de ventilación de una mina subterránea se debe determinar la cantidad total de aire necesario y la caída total de presión. Con estos datos se planean las obras y se selecciona el equipo de ventilación adecuado Así, el objetivo de este diseño de sistema de ventilación es proporcionar condiciones ambientales subterráneas seguras, sanas y saludables. En este sentido, el presente texto refiere la forma en que la fricción, densidad, humedad, temperatura, determinación de requerimientos de aire, dimensiones, contaminantes de escapes de motores diesel, ventilación natural, envases y difusores entre otros factores afectan el diseño de sistemas de ventilación para minas subterráneas.

Mar 1, 1983

By George S. W. Cumpston

El presente texto describe los factores que intervienen en la economía de la molienda con bolas, considerando la carga y calidades de las mismas. Para determinar cuáles son los factores en el estudio económico, es necesario conocer las cuatro calidades básicas de las bolas de las moliendas: las bolas de aleación de acero, forjadas y con tratamiento térmico, las bolas de acero al carbono forjadas y con tratamiento térmico, las bolas de aleación de acero fundido y las bolas de fierro fundido. Los productos fundidos generalmente no son tratados térmicamente y las bolas de fierro fundido son un producto de bajo precio y más ordinario. En este sentido, una bola tratada térmicamente sea en aleación de acero o de acero al carbono, tendrá una estructura granular más fina que las de los productos fundidos. Para fijar la economía de un tipo de bola, se utilizan dos formas de investigación: la prueba de bolas marcadas y la de resultados de producción, estableciendo esta última como la más exacta, aunque requiera molinos duplicados para medir su producción. Luego, se procede a experimentar con diferentes tipos de bolas -a través del costo de transporte y manejo requeridos para moler una tonelada de mineral- y asi determinar cuál es la bola más económica para cada operación. Posteriormente se evalúa la facilidad de la molienda y se delimita la carga de bolas que se aproxime mejor a la carga balanceada.

Jul 20, 1960

By Elmer Tveter

El presente texto refiere los factores que controlan la elección de un reactivo de flotación como: Flow Sheet a emplearse, clase de mineral, suministro de agua, ubicación de la Planta y los sistemas de pagos de la fundición. Dentro de estos factores, solo se considera a la clase de mineral y el suministro de agua como los factores variantes, y se pueda verla forma cómo afecta esto la elección del reactivo a emplearse en flotación.

Jul 1, 1960

By Y. Z. Ma

This paper presents a matrix formulation of factorial kriging, and its relationships with simple and ordinary kriging. Similar to other kriging methods, factorial kriging can be applied to both stationary and intrinsic stochastic processes, and is often used as a local operator. Therefore, the concepts of intrinsic random function and local stationarity are first briefly reviewed. Kriging is presented in a block matrix form in which the kriging solution is useful not only for understanding the relationships between simple and ordinary kriging methods, but also the relationships between interpolative kriging and factorial kriging. When used as a signal/noise-filtering method, factorial kriging is especially useful for multiscale modelling. Examples for general signal analysis and geophysical data signal filtering are given to illustrate the method..

Jan 1, 2014

By R. Luo, R. V. Kumar

"The co-deposition of cobalt and nickel as a binary alloy has been studied by both cyclic voltammetry and long-period controlled-potential electrolysis. Cyclic voltammetry experiments showed that the cathodic current density for the mixed Co-Ni (Co-Ni=1:3) electrolyte is noticeably higher than that obtained on electrolyte containing single CO2+ or Ni2+ (II) salt of the same ionic strength. The onset potential observed for the mixed salts electrolyte was also less cathodic (negative) than that for the single metal salts, respectively. The effects of a number of operational and compositional parameters on the co-deposition of cobalt and nickel were studied. The parameters under investigation include cathode (deposition) potential, temperature, CI-/Sol ratio in the electrolyte, the amount of additives such as H3B03, and acidity of the electrolyte.Optimum operational conditions were established for the deposition of cobalt and nickel binary alloy. These results are discussed with respect to feasibility of reclaiming cobalt, nickel and chromium from mixed superalloy scraps by melt-refining (under nitrogen and/or ammonia), followed by electrorerining of cast anode for co-depositing Co/Ni and thermal decomposition of chromium nitride for recovering chromium metal."

Jan 1, 1997

By H. E. Elliott, R. S. Busk, A. T. Peters

ONE of the problems of the fabricator of metals and alloys is the propensity of some composition ranges toward abnormal grain growth during certain stages of fabrication. In this respect magnesium alloys are no exception among alloys. Fortunately, convenient foundry control methods have been developed by which the abnormal grain growth possible in certain magnesium-alloy castings can be suppressed. An unusual characteristic of magnesium alloys, however, is that castings of some composition ranges are subject to local grain growth during heat-treatment without the necessity of intentional mechanical stressing of the part prior to heat-treatment. This effect occurs only under certain critical casting conditions, and only in certain alloys of greater than about 8.5 per cent aluminum content, such as C alloy (Mg, o per cent Al, 2 per cent Zn, 0.2 per cent Mn) and G alloy (Mg, i0 per cent Al, 0.2 per cent Mn). The first observation of this phenomenon in cast magnesium alloys occasioned much surprise, since it is not observed in other metals. Jeffries and Archer' have stated that "the grain size of cast metals, provided they have not been plastically deformed, cannot be changed by heating below the melting point." The study of the conditions leading to abnormal grain growth in cast magnesium alloys, and of the mechanism of this phenomenon, has led to some very interesting observations. Perhaps the most significant of these was the observation that stresses originating from cooling contraction in magnesium-alloy castings are the only stresses necessary, under certain conditions, to cause local recrystallization and subsequent grain growth in the casting during heat-treatment. of abnormal local grain growth was a definite problem in the production foundry on C alloy sand castings. Illustrated (Fig. r) is a picture of a casting scrapped because of this defect. A mottled effect is produced in coarse-grained areas by suitable etching solutions. The properties of metal in the affected area are much impaired by such grain coarsening. Ultimate tensile strengths of half the normal value have been measured in metal of this nature. In this paper are described the techniques that have been developed by The Dow Chemical Co. for studying, and in large measure solving, this production problem. Also discussed are studies of the mechanism by which excessive grain coarsening occurs, and the fundamental conditions that produce this effect. The abnormal grain growth discussed in this paper will be referred to as "germination," since this term has been defined' as any process leading to an abnormally coarse grain size. This paper deals only with abnormal local grain growth that may occur during the solution heat-treatment of certain magnesium-alloy castings, as dis-

Jan 1, 1945

By Jiaxin Zhou

Acid mine drainage is a serious and chronic environmental problem of mining. This paper discusses the factors affecting the rate of acid generation by mine rocks and illustrates the relevance of these factors to the mines of the Northern Territory, Australia. The factors may be divided into two groups: internal factors and external factors. The first group covers characteristics of ores, mine waste rocks, tailings, etc and the second group covers surrounding conditions. The latter is further divided into four sub-groups, viz surrounding temperature and pressure, chemical conditions (ferrous/ferric adsorption ratio, total iron concentration, oxygen concentration and pH), surrounding biological conditions and mechanical conditions. Special attention is given to the surrounding P-T conditions, especially water partial pressure, and its relevance to the Northern Territory mines.

Jan 1, 1994

By D. D. Tannant, H. Ozturk

Thin spray-on liners are increasingly being used as rock support in underground mines. The adhesive strength between the liner and the rock surface is an important design parameter. Adhesion tests were conducted to assess the impact on adhesion of the presence of oil, water, and dust on a substrate, and the roughness and grain size of different substrates. Other factors such as curing time, loading rate, and liner thickness were also considered. Adhesion was measured using a pull test of a 33 mm diameter elevator bolt attached to an over-cored section of liner with strong epoxy. Most tests were performed using Tekflex liner material, although five other liner products were also tested. Adhesive strengths of about 2 MPa can be achieved with Tekflex under optimal conditions. Long-term creep tests showed that the adhesive strength could drop by at least 50% when the liner carries load for about a month. Where the rock surface is contaminated with dust or the rock is weak in tension, it may be difficult to reach adhesion strengths of 1 to 1.5 MPa. As the thickness of the liner increases, the adhesive strength to a substrate appears to decrease.

Jan 1, 2007

By B. J. Scheiner

The Bureau of Mines, Department of Interior, has been investigating the use of polyethylene oxide (PEO) as a flocculant for a variety of mineral wastes. As part of this investigation, the hydrodynamics of the flocculation process were studied. It was determined that to obtain optimum dewatering results, the factors of energy input into the stirrer, polymer concentration, and polymer dosage must be considered. Lt was found that at a given polymer concentration, there was an optimum stirrer speed and polymer dosage. With excess PEO, the amount of water removed in the trommel decreased, but no evidence for steric stabilization was observed.

Jan 1, 1987

By J. A. Herbst, R. Mackelprang, J. D. Miller

Droplet size distributions were determined by stabilizing in gelatin and measurement of the distributions by means of computerized image analysis Several variables that affect droplet sizes were studied and the resulting size distributions were modeled via a population balance equation Key parameters in the model were related to the physical properties and operating conditions of the systems examined using a multiple linear approach

Jan 1, 1981

By Donald Hurd, James Rowland, Richard Mainiero

In previous conferences the authors have reported on toxic fumes generated by the detonation of ANFO. The research reported here extends the earlier work to include an emulsion blasting agent and ANFO/emulsion blends. Explosive mixtures were shot in 4-inch Schedule 80 steel pipe (outer diameter 4.50 in (11.43 cm), inner diameter 3.83 in (9.72 cm)) in a chamber in the experimental mine at the Pittsburgh Research Laboratory (PRL). Following each shot, the fumes in the chamber were analyzed using on-line instrumentation.

Jan 1, 2001

By Richard Mainiero, Donald A. Hurd, James H. Rowland

In previous conferences the authors have reported on toxic fumes generated by the detonation of ANFO. The research reported here extends the earlier work to include an emulsion blasting agent and ANFO/emulsion blends. Explosive mixtures were shot in 4-inch Schedule 80 steel pipe in a chamber in the experimental mine at the Pittsburgh Research Laboratory (PRL). Following each shot, the fumes in the chamber were analyzed using on-line instrumentation. A major goal of the research was to gain a better understanding of the factors that lead to the generation of toxic fumes in blasting operations. Earlier studies have suggested that the high nitrogen dioxide and nitric oxide concentrations in product clouds might be the result of the poor confinement provided by relatively weak ground strata or the exposure of the explosive to ground water prior to shooting the shot. Various mixtures of ANFO and emulsion were detonated in schedule 80 steel pipe and galvanized sheet metal pipe to evaluate the effect of confinement. Explosive mixtures were also allowed to soak in water for less than one day, one week, one month, and two months to determine which explosive mixtures would be degraded and observe what effect this degradation had on fume production. Results indicated that the production of nitrogen dioxide increased with low confinement of the detonating explosive and with exposure of the explosive to water.

The seam gas content at Westcliff Colliery is 12-15m3/tonne of coal.Composition ranges from 99% CH4 to 52% C02 in one area. Desorption rates are proportional to gas contents and CH4 is preferentially desorbed. A crushed zone of reduced permeability advances with the face - at Westcliff ribside crushed zones are 2.5 to 6.5m wide. Poor strata control widens crushed zones. 12 months of pre-drainage allowed 2 heading development and longer pillars to be used in a virgin area instead of 3 or more headings without drainage. Machined coal may lose as much as 1.6m3/tonne being conveyed out of Westcliff Colliery. Experience differs from mine to mine. Permeation is affected by time, strata movements, changing water content, and changing stress. Permeabilities vary from lOmd for Pittsburgh Seam to less than 1 and for the Bulli Seam. All these data and differences await further investigation.

Jan 1, 1982

By Dugan K. J

Mine operators are currently in a situation where market forces are acting to reduce profit margins and at the same time, regulatory bodies are insisting on improved mine safety and stability. This means that ground support must be made more cost efficient while maximising operator and equipment safety.A key aspect of ground support efficiency is the 'in the ground' performance. This paper discusses the factors that influence the way rock bolts and cable bolts perform. It highlights the need to know how support efficiency varies in different ground conditions.

Jan 1, 1992

By I Jabouri

There are many physical factors that can affect the self-heating rate of coal. The presence of seam gas has often been referred to as inhibiting coal self-heating due to the limited access of oxidation sites created by the presence of the gas adsorbed on the coal pores. Similarly, the presence of bed moisture in the coal also acts as an inhibitor of oxidation by blocking access of air into the pores. Gas drainage of a coal seam prior to mining removes both gas and moisture from the seam. Bulk coal self-heating tests in a two-metre column on both gassy, as-mined and gas-drained, dried high volatile bituminous coal show that removal of gas and moisture from the coal accelerates the rate of self-heating to thermal runaway from 8.5 days to 4.25 days, from a start temperature of 30¦C, with an airflow of 0.25 L/min. The corresponding gas evolution pattern for each of these situations is different. Therefore, it is necessary to take this change in coal condition into consideration when developing a spontaneous combustion management plan.

Jan 1, 2005