Search Documents

By Milorad Cirkovic

Kinetics of copper concentrate oxidation in roasting processes in a fluidized bed reactor has been studied at temperatures between 600°C and 720°C using particles of 0.038 to 2.5 mm in average size. The analysis of composition of samples has been done by chemical methods. Phase composition has been determined by Siemens X-ray equipment with Cu anticathode and Ni filters at a voltage of 40 kV and a current of 18 mA. The content of sulphur has decreased from 33.23 to 19.02 mass percent with the increase of temperature, but the content of Fe304 has increased from 0.15 to 17.14 mass percent. The new mechanism of copper concentrate oxidation in a fluidized bed reactor is proposed in this study. It has been shown from the mathematical model that the velocity of oxidation of copper concentrate between 600°C and 720°C is virtually controlled by the rate of diffusion of 02 through the layer of reaction product.

Jan 1, 1999

By I. Gaballah

The electrochemical behavior of a chalcopyrite concentrate having a high pyrite content was studied in HC1 by potentiodynamic, potentiostatic and galvanostatic experiments using a cell having separate anodic and cathodic compartments. Anodic oxidation of chalcopyrite particles was realized both by their contact with the cunent feeder and by reaction with ferric and cupric ions. An increase of current leads to a more selective dissolution of chalcopyrite. Surface passivation was observed after an electrolysis time related to the cell current. Cathodic reduction of chalcopyrite concentrate seems to be more promising. Almost complete conversion of chalcopyrite to a copper sulfide (Cui.8.S) is observed, whereas no reaction of the pyrite was detected. This confirms the possible selective dissolution of copper from the chalcopyrite concentrate. Copper sulfide obtained by cathodic reduction was leached using a cupric chloride solution.

Jan 1, 1994

By J. Markussen

The Falconbridge Matte Leach Plant was based on leaching Ni-Cu matte with strong hydrochloric acid in rubber lined equipment. It operated from 1968 to 1983 as a precursor to Nikkelverk's present C12 Leach. The process comprised two S.X. systems. NiC12.4H20 crystallization, crystal drying, NiC12.H20 pyrohydrolysis and HC1 gas recovery. The naphtha fired fluid bed pyrohydrolyzer produced granular NiO, subsequently reduced with H2 to granular nickel for sale. The development and operation of the pyrohydrolyzer are described

Jan 1, 1991

By V. I. Lakshmanan

Crown ethers are gaining importance in separation technology specifically for rare earth elements (REE, La to Lu plus Y) and precious metals (Au, Ag, Pt, Pd, Rh and Ir) due to their specific binding ability, metal complex stability and high extraction efficiency. The selectivity of crown ethers in extraction of these metals depends on different factors, including the cavity diameter and nature of a donor atom of the crown ether, size and charge of the metal ion, diluents and counter ion. Demand for strategic REE and precious metals are consistently increasing in the world while the separation of these metals is most challenging tasks. In this paper, the use of crown ethers in separation of REE and precious metals, reaction mechanisms and simplified process flowsheets will be elucidated. New reagents with high selectivity for the separation of these metals are further expected to produce high purity metals.

By E. A. Trillo, L. E. Murr, R. D. Flores, J. C. McClure, B. M. Nowak

Complex vortex and swirl-like solid-state flow phenomena have been observed in the residual microstructures characterizing the friction-stir welding (FSW) of copper to 6061 aluminum; 2024 aluminum to 6061aluminum,2024 aluminum to 1100 aluminum, 2024 aluminum to 7039 aluminum and 2024 aluminum to 2195 aluminum. These flow phenomena are characterized by intercalation lamellae composed of dynamically recrystallized grain structures of the dissimilar metals which provide a super-plastic-like mechanism for the FSW flow in the solid state; there is no melting and temperatures at the weld center do not exceed about 0.8 TM (where TM is the absolute melting temperature (K)). In experiments to be described and illustrated, optical or light metallography (LM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques are utilized in examining residual FSW microstructures corresponding to tool rotation (stirring) speeds ranging from 400 to 1200 rpm, and traverse (or actual welding) speeds of 1 to 2 mrn/s.

Jan 1, 1999

By Chikabumi Yamauchi

The comprehensive scientific development of conventional industrial technologies stimulates the creation of new ones in the next generation. Prof. Akira Yazawa has just accomplished such an important work in the non-ferrous pyrometallurgical field. The results of his successful research are immortal. The research group of the author has conducted since 1985 fundamental studies on the application of sodium carbonate slag to copper fire refining. In the present paper, a calculation method for the distribution ratios of impurity elements between sodium carbonate slag and molten copper will be shown. The specific treatment by sodium carbonate slag will also be presented as an effective way for reducing each impurity content in the molten copper to 0.1 mass ppm, which is the level required for the production of high purity copper. The thinking-out of this evaluation method gets a hint from the Equation (2) in the text which was proposed by Prof. Akira Yazawa.

Jan 1, 2003

By Laurentiu Nastac, Ruslan Mudryy

"This paper investigates the solidification of cast energetic materials. An active cooling and heating (ACH) technology and a mechanical vibration (MV) technology were applied to achieve unidirectional solidification during casting and to reduce cracks, gas pores, and shrinkage defects. The design parameters of these technologies were developed via Computational Fluid Dynamics (CFD) modeling and thermal stress analysis. Concerning the ACH technology, the number of cooling/heating sections and their temperature profiles and time sequences were optimized based on the thermo-physical properties of the energetic material as well as the riser and mold diameter, thickness and type. The ACH technology will also decrease the thermal stresses during casting of energetic materials and therefore minimize the formation of potential cracks that may form during the casting process. The MV technology will help to remove air entrapped during pouring process and decrease the detrimental gap size between the projectile and the solidified energetic material.IntroductionCasting processes are widely employed in the manufacture of products with intricate shapes and, in particular, in applications where the material of the final product is sensitive to machining. It is especially useful in processing of energetic materials. The cooling conditions applied in the casting process can affect the quality of the final cast in terms of void formation, residual stress distributions, and mold separation. Substantial shrinkage is also observed due to the density change upon solidification [1-3]. Residual stresses are known to be closely related to the formation of cold cracks and hot tears during casting. The formation of a gap between the mold and the cast material is of critical importance due to its deleterious effect on heat removal and on crack formation. In the casting of energetic materials all these defects can significantly impair the detonation velocity, Gurney energy, and insensitive munitions characteristics of the formulation, and lead to catastrophic accidents in explosives handling [ 4-5]. Imposition of carefully controlled cooling condition is thus critical in optimizing the cast quality that could help avoid such destructive effects."

Jan 1, 2013

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"The disposal of wastes is a serious environmental problem, since available landfill space is dwindling. Their treatment by pyrolysis or combustion has merit, and the corresponding fuel or power production is of technological interest. However, such processes need a rigid control of emissions. This work addresses the gaseous light hydrocarbons (LHCs) generated during sequential pyrolysis and partial oxidation of unserviceable tires, PET bottles, com wastes (DDGS) and sugarcane bagasse in a two-stage laminar-flow horizontal furnace, kept at 1000 °C. Gas chromatography was used to identify and quantify the components of the emitted gaseous light hydrocarbons. The results showed that the biomass residues generated the highest emissions of aliphatic hydrocarbons, whereas PET generated the most aromatic hydrocarbons. When stainless steel meshes were inserted in the exhaust flow, it was found that hydrocarbon emissions were curtailed; as such meshes catalyzed partial conversion of these carbon-bearing gases to carbonaceous nanomaterials.IntroductionLight hydrocarbons (LHCs) are volatile organic compounds, consisting of hydrogen and carbon with low molecular weight; the most common species are methane, ethane, propane, butane, etc. LHCs are valuable since they are a very important energy resource. However, uncontrolled release of light hydrocarbon gases to the atmosphere should be avoided [l, 2]. In this work, a development is presented for the evaluation of LHCs generated during the controlled pyrolysis/combustion of several wastes in a two-stage laminar-flow horizontal furnace. Samples of unserviceable tires, post-consumer PET bottles and waste residues from the bioethanol industry (DDGS and sugarcane bagasse) were burned. A catalyst system, consisting of stainless steel screens, was tested for its effects on the gaseous emissions."

Jan 1, 2011

By Sergey Shabala

Green leaf tissues convert solar energy into the energy of chemical bonds of sugar molecules during the process of photosynthesis. The efficiency of this conversion can be much higher than efficiency of any of the currently known silicon-based solar panels. Importantly, vast amounts of CO2 are assimilated during this process. The efficiency of photosynthesis is critically dependent on the availability of a large number of nutrients, among which metal cations such as K, Ca, Mg, Cu, Zn, Fe, Mn, and Ni play a key role. In this paper I summarize basic requirements and major functions for each of these essential nutrients in plant photosynthesis, both at the whole-plant and molecular level. I will talk about how these requirements may be affected by the global climate trends and discuss the prospects of creating artificial photosynthetic “bioreactors” for efficient energy conversion and CO2 assimilation.

Jan 1, 2009

By John J. Jonas, Sang-Hyun Cho, Ki-Bong Kang

"The recrystallization behavior of Nb micro alloyed steels containing Cr, Mo, Ni and Ti. was studied using hot torsion testing with the aim of modeling the recrystallization processes and the mean flow stress taking into account the microstructural behavior during hot rolling. The kinetics of static and metadynamic recrystallization were characterized and appropriate expressions were formulated for the recrystallization kinetics. These are shown that the recrystallization kinetics depend on steel composition and the processing conditions. The stress-strain curves were determined in order to derive new equations for the peak stress, peak strain, mean flow stress and softening kinetics. The peak strain is influenced by the presence of alloying elements; their addition, which has a solute drag effect, retards the rate of grain boundary motion, shifting the peak to the right. The addition of Nb to the steel results in a significant increment in the activation energy for hot deformation, and Mo has smaller effect than Nb, but Cr has the opposite effect. It was also found that the deformation activation energy in these steels was not altered by the addition of Ni. The rate of metadynamic recrystallization increases with strain rate and temperature and is observed to be independent of strain, in contrast to the observations for static recrystallization.The mean flow stress (MFS) calculations, based on the Sims analysis, are then compared with the predictions of a model based on an improved Misaka mean flow stress equation in which solute effects, strain accumulation, as well as the kinetics of static and metadynamic recrystallization are accounted for. Good agreement between the measured mean flow stresses, which is obtained from the mill logs of POSCO Kwangyang #3 HSM (hot strip mill), and 'predicted ones is obtained over the whole range of rolling temperatures. The results demonstrate that dynamic recrystallization followed by metadynamic recrystallization, supported by the unexpected load drops, sometimes occurs for the rolling schedules studied in the present analysis."

Jan 1, 2001

By Carl C. Nesbitt

A process has been developed to recover and recycle metals from wastes of brass foundries which contain copper, zinc and lead in various quantities. Tests were conducted to evaluate several leachants, including sulfuric acid, ammonia, hydrochloric acid, cyanide and acetic acid, and to determine the optimum leaching conditions, such as air flow rate, initial copper ion concentration, temperature, and agitation strength. Sulfuric acid containing copper sulfate with dissolved oxygen is the most successful leachant. More than 99% of the copper and zinc originally present in the waste was dissolved, while only 0.5% of the lead entered the solution after 14 hours of leaching. The leaching mechanisms of copper, zinc, and lead are proposed. The copper and zinc can be recovered from the solution by electrolytic processing. The unleached residue may be converted to a lead carbonate which can be converted to litharge at 400-450°C and to massicot at temperature above 500°C by calcination.

Jan 1, 1995

By P. Umadevi

In the light of the discovery of the new super-conducting YBa2Cu3O7-x (YBCO), reactions in the Y2O3¬CuO-BaO system at 1300°C was investigated. The search was for any new phase that may be formed in the system at 1300°C (only 950°C reactions are known so far). 35 mixtures of different compositions were prepared and heated at 1300°C. No new phase was obtained. It was found that YBCO is decomposed at this temperature and Y2O3 and BaCO3 are the major components in the solid obtained after firing in air. However, on cooling the melt slowly and annealing at 950°C YBCO reforms. Such reactions on cooling might have implications on processing of the superconductor YBCO for practical applications as well as on its crystal growth by flux method.

Jan 1, 1989

By I. Peerawattuk

Growing demand for Li-based battery technologies is leading to an unprecedented growth in the lithium industry. Although innovation in battery technologies has pushed lithium into the spotlight, lithium was not always known for its application in batteries. The primary use of lithium—prior to the introduction of commercial lithium-ion batteries in the early 2000s—was in the ceramics, glass, grease, and the medical industry. Before being converted into usable forms, lithium products must be upgraded from the raw material. Processes for recovering lithium may involve: thermal treatment, water leaching, solar evaporation, ion exchange, carbonation, and electrodialysis. Presented, is a historical review of lithium applications and the different techniques of converting lithium-rich minerals and brines into usable products with additional discussion on future lithium extraction processes.

By Dany Racine, Daniel Marceau, Denis Laroche, Dmitry Lukovnikov

Carbon base materials play a critical role in the performance of Hall-Héroult cell. The determination of their thermo-physical properties is of primary importance for modeling and designing complete cell systems. However, overcoming the associated experimental hurdles is complex and often underestimated. Of them are the Poisson’s ratio measurements and the continuous oxidation/burning of the materials at temperatures above 200°C. The novel procedure developed in this research is based on the Gleeble® 3800 system. Its vacuum chamber allows test with a chosen atmosphere at temperature of more than 1000°C. Young’s modulus, Poisson’s ratio and the coefficient of thermal expansion values can all be adequately measured using a single test. Cylindrical carbon samples (: 50mm, L: 100mm) were tested in the modified system at temperatures ranging from room to 950°C without any trace of oxidation. The resulting values were also in good agreement with literature data for a specific graphite material.

Jan 1, 2015

By Yasuo Ojima

The mainstream of copper smelting processes in the world today is a combination of Outokumpu type Flash smelting and PS (Pierse Smith) converting process. Presently it can be estimated that about 50% of the worldwide copper production is produced by the Flash smelting process and 80% by the PS converting process. PS converting process due to its operational flexibility and despite its batch character of operation has been widely used in many smelters for more than 100 years. However, an environmental issue has been pointed out related to this process because of the difficulty of handling the fugitive gases. Recently several copper smelters in the world have been newly construeted and others have executed major modification and modernization. The continuous converting process has been applied in many of them instead of PS converting process. This paper compares PS to the emerging continuous converting process and makes a prospect of the future of the copper converting process.

Jan 1, 2003

By Von L. Richards

Rapid Freeze Prototyping (RFP) is a novel solid freeform fabrication technology that creates parts by depositing water droplets and freezing them rapidly to form layers. An investigation into the smallest thickness that can be achieved by the RFP process was conducted. The factors that could significantly affect the thickness of the part built by this process including substrate temperature, volumetric feed rate, table velocity, nozzle frequency, nozzle standoff distance, and head pressure were considered. A shell building technique for use with the RFP system has been developed. Thin wall ice patterns have been invested using production shell building techniques and an alcohol-based slurry. The finished shells were quantitatively evaluated by inspecting their total shell thickness, mold cavity dimensional reproducibility, and shell strength. Pattern loss is influenced by not only the alcohol / water interaction but also the starting thickness as it relates to thermal mass.

Jan 1, 2008

By Liyuan Chai, Qin Liu, Bing Peng, Jia Wang, Qiang Zhang

"Electrolytic Manganese Residue (EMR) was used as the main material to prepare cementing material activator for the utilization of the residue from electrolytic manganese dioxide (EMD) or electrolytic metallic manganese (EMM) production. The effects of chemical activation, thermal activation and mechanical activation on retarding activity and excitation activity of EMR were investigated according to the setting time and activity index of EMR-slag cementing material. The results showed that the EMR exhibited good activating performance after being ball-milled for 18 min and then treated for 1-2 hours at temperature range of 350-450 ?. The optimal properties of cementing material activator were achieved at the weight percent ratio 30 : 3 : 5 of EMR/Ca(OH)2/cement clinker.IntroductionMany hazardous industrial solid wastes such as blast furnace slag, fly ash, steelmaking slag, chromic slag and electrolytic manganese residue [1] are generated n China and their amounts increases every year. The accumulation of the solid wastes during past years is very huge and they could be hardly recycled effectively as a sustainable resource. 2.35 billion tons of industrial solid wastes have been produced up to now [2]. It is estimated that they would exceed 3.3 billion tons by the end of 2015 [3]. On the other hand, the quick development of Chinese infrastructural construction needs more cementing materials. The production of traditional building materials consumes lots of natural resource such as clay and limestone and discharges at least 1 ton CO2 and other pollutants per ton clinker [4]. Therefore, it is necessary to develop new types of cementing materials instead of clinker [5,6]."

Jan 1, 2012

By Robert C. Laudon

Spectral reflectance data for 335 minerals, including 228 minimum-maximum combinations for anisotropic minerals giving a total of 563 data sets, have been collected from the literature and combined into a single database. Quantitative color values for x, y, Y, Ad , and Pe referred to ICI standard i11uminant C have been calculated from the spectral reflectance data and are included in the database. The programs plot spectral reflectance curves together with all quantitative color data for each mineral in the database. The plots and data can be directed to a dot-matrix printer such that a databook of quantitative color and spectral reflectance having one mineral per page can be generated for the ore microscopy laboratory. In addition, by sorting the database and grouping the minerals, groups or individual minerals can be plotted on the chromaticity diagram, and this plot can also be sent to a dot-matrix printer. The programs are written in compiled BASICA for an IBM-PC with graphics capabilities and at least 128KB random access memory (RAM). The databases are accessible either through the BASIC programs or through any commercial database system capable of loading and writing to an ASCII format sequential file. The programs and database are available by sending a blank diskette and self addressed, stamped envelope to the authors.

Jan 1, 1987

By P. Wieser, D. Feke

"Priming of filters with small pores is influenced by the surface tension of the liquid metal and may be complicated by freezing • Freezing followed by melting has been observed experimentally. This process has been modeled on the basis of one dimensional heat flow by radiation to the filter and by conduction in the metal. Also considered are super-heat of the metal and the initial filter temperature. The results of the model provide useful guidelines for the application of filters. IntroductionFiltration has been recognized as a valuable method of refining by removing suspended phases from liquid metals or alloys. Woven fiberglass type fabrics and wire screens were used initially in the aluminum industry. With the introduction of the ceramic filters that exhibit improved inertness and refractoryness, filtration has been introduced to higher melting alloys including cast irons, superalloys, stainless steels, as well as low and medium carbon low alloy steels. A considerable literature is delveloping rapidly on the progress in applications and the advances in understanding the mechanisms and effectiveness of filtration processes (1-8).With the use of filtration for different alloy systems for the production of cast to shape parts a bewildering variety of gating system modifications has been developed (Figure 1) to accommodate the installation of filters in the mold. The modifications have two principal purposes: 1) the runner expansion is intended to compensate for the resistance to flow due to the filter and that of the captured inclusions, and 2) the metal reservoir upstream of the filter, provides a temporary by-pass which permits metal to flow across the filter and heat it until priming can be accomplished. priming of.filters by low and medium carbon steel is readily accomplished but, compared to such alloys as cast iron or 19 Cr-9Ni stainless steel, requires greater precautions to avoid failure to prime by excessive freezing on or inside the filter pores. This problem is further examined below:"

Jan 1, 1986

By H. Conrad, K. Jung

"The effect of an external electric field E=5(+) kV/cm applied during the solution heat treatment at 500°-550°C of three commercial Al-Mg-Si alloys (AA6061, AA6022 and AA61l1) on the asquenched resistivity Pw and hardness H.,NULL, w was investigated. It was found that the field gave a significant increase in Pw and in Hv,w, for AA6022 and AA6111, but had no clear effect on AA6061. Thermodynamic analysis gave that the effect of the field on AA6022 and AA6111 was to reduce both the enthalpy ?H, and entropy ?H, of solution. Considering the chemical composition of the three alloys it appears that the influence of the field may depend on the amount of Cu plus excess Si present in the alloy.IntroductionKlypin and Soloviev [1, 2] were the first to report that the application of an external electric field during solution heat treatment (SHT) of Al alloys gave an increase in the as-quenched resistivity and hardness. They attributed these effects of the field to an increase in solubility of the alloying constituents during the SHT. More recently Liu and coworkers [3, 4] also reported an increase in the as-quenched resistivity of Al-Li alloys with application of an electric field during SHT. Further, the present authors [5] found that the application of an electric field during the SHT of the commercial Al-Mg-Si alloys AA6022 and AA61i1 increased their as-quenched resistivity and hardness. Their thermodynamic analysis of the results indicated that the field decreased both the enthalpy ?H, and entropy ?S, of solution."

Jan 1, 2004