Search Documents

By X. Baolin, R. Guru, M. Peiravi, M. K. Mohanty, Z. Qian, R. Ma, Z. Yude, L. A. Ackah

"Acid mine drainage (AMD) is produced when exposed pyrite (FeS2) reacts with air and water to form an acidic solution that usually contain contaminant levels of heavy metal ions. AMD can potentially contaminate surface water and soil if not treated. The primary objective of this study was to investigate the removal of dissolved aluminum, iron and zinc metal ions from natural AMD using water treatment residue (WTR), a low-cost adsorbent. WTR sorbent generated as waste material in drinking water treatment plants (WTP) was characterized and utilized for the sorption of Al, Fe and Zn in AMD collected from an abandoned coal mine site in southern Illinois that generates approximately 20 gallons per minute of AMD. Sorption experiments were performed using batch technique to obtain rate and equilibrium data. The effects of various parameters on sorption capacities of WTR were observed by varying contact time, pH of the AMD and WTR dosage. The adsorption studies showed rapid uptake in general for the first 80 minutes for Fe and Zn but much earlier for Zn. Further increase in contact time did not show significant change in equilibrium concentration indicating the onset of adsorption equilibrium. After the batch treatment of the AMD water with the WTR, the removal of Al, Fe and Zn were 99.8%, 99.85% and 95.5% respectively. The pH of AMD increased from 2.64 to a near neutral point of 6.74 after treatment. The laboratory results show that the low-cost WTR, which is an abundantly available industrial waste, has proven potential to significantly reduce the high metal ions in acid mine drainage. INTRODUCTION Mining activities provide the basic raw materials needed for infrastructure development and economic growth world-wide. However, it is well recognized that mining activities have been the cause of a variety of environmental pollutions, including AMD. Water seeping out of an old abandoned mine is generally characterized by low-pH with heavy loads of dissolved sulfates (SO4) and metal species such as Fe, Al and Zn among other dissolved elements categorized as toxic metals. The Bureau of Land Management’s Abandoned Mine Lands (AML) program reported the existence of about 46,000 abandoned mines in the United States. Several environmental problems have been reported to be associated with these mined out sites such as heavy metal poisoning, loss of vegetation, air pollution etc. (Boulanger & Gorman, 2004)."

Jan 1, 2017

By G. K. Hoffman

Humate, defined as weathered coal or mud-stone rich in humic acid (HA) and fulvic acid (FA) have been mined, primarily as soil amendments or drilling mud additives, in New Mexico for 15-20 years. The New Mexico humate resource is estimated to be 11 Gt, including weathered coal and organic mudstone. The HA and FA content determines the end-use, therefore a simple and consistent method of measuring organic-acid content was developed. The New Mexico Bureau of Mines and Mineral Resources method is based on repeated alkali leaching and acid precipitation. Precipitates of humate are ashed, with mass balance of solids maintained, to correct for material added during alkali-acid treatment. Analyses of upper coal member, Cleary Coal Member (Menefee Formation) and Fruitland Formation samples from the southeast San Juan Basin show ashing to be important in accurate analysis of FA content. Ash in the total FA fraction averages 70% compared to 2% in HA. The FA in weathered coal and organic mudstone are similar, although HA is significantly higher in the former. As weathering progresses, the FA content of weathered coal increases faster than in organic mudstone because of the greater total organic material in coal.

Jan 1, 1994

By M. Deutsch

A common casualty of modern open pit mine optimization is the assurance that the resulting design is actually achievable. Optimized mine plans that consider value and a bare minimum of precedence constraints do not, in general, translate into practical, operational mine designs that can really be used in the field. Ultimate pits may come to a sharp point at the bottom. Schedules may require taking small parcels of material from many disparate areas of the pit in a single period. And grade control polygons may be ragged, narrow, and not minable with realistic equipment. In this paper all of these problems are addressed by encoding these three fundamental open pit mine optimization problems as maximum satisfiability problems. Maximum satisfiability provides a useful framework for problems that are non-linear and may guarantee the optimality that metaheuristics cannot. INTRODUCTION Open pit mines are large and complicated operations, which require significant initial and ongoing investment. A single mine may employ hundreds or thousands of people and creates substantial benefits for both the surrounding and global communities. Planning an operation of this magnitude requires a lot of effort and cannot be done optimally by hand. Mining engineers today rely on many techniques from operations research to guide decision making, and to maximize the value of the mine. Techniques including linear programming, metaheuristics, and network algorithms are all used to solve different problems throughout mine design and optimization. However, techniques based on Boolean satisfiability, including the optimization extension of maximum satisfiability, have not seen much use in mining despite being used in many other fields including electronics design, scheduling, and artificial intelligence. We claim that maximum satisfiability is a useful and meaningful way of expressing and solving optimization problems in mine planning. However, this technique does not come without challenges; the problem is NP-hard, and modern techniques for solving these problems can struggle with the number of variables and clauses that a typical mining problem requires. Also, some of the constraints that mining must contend with do not fit nicely into the satisfiability paradigm. Despite these challenges, we believe that maximum satisfiability provides a useful framework for considering operational constraints and expressing some problems that other techniques can't easily express. Maximum satisfiability can be solved exactly, yielding the true optimal answer which metaheuristics cannot guarantee. In this paper we show the applicability of maximum satisfiability to mining by specifying three fundamental problems in open pit mine optimization. We show how these fundamental problems can be formulated and how they can be extended within the framework of maximum satisfiability. For the remainder of the paper we first give a brief background on common elements between the three problems and an introduction to satisfiability. Then we tackle the three problems; the Ultimate Pit Problem, the Block Scheduling Problem, and the Grade Control Polygon Problem. In the Ultimate Pit Problem we specifically show how to extend the problem to support a minimum mining width – a coveted result for many mining engineers. We then discuss some of the complexities and shortcomings of this framework and possible research directions.

Jan 1, 2019

By Utku Gumus, Ertan Bostanci, Hanifi Copur, Ahmet Rüfai Bilgin, Ugur Altay

"Field observations on replacements of 12-inch constant cross-section double disc cutters in Tuzla Wastewater Tunnel excavated by an EPB TBM with 3.151 mm excavation diameter excavating hard rock are summarized. Cutter life is correlated to rock’s uniaxial compressive strength and Cerchar abrasivity index, and TBM operational parameters. Number of cutter replacements, average cutter replacement rates and types of cutter damages are summarized. The relationships between cutter life and rock properties and TBM operational parameters are analyzed by single variable regression method. Detailed analysis between chainages 1+200 and 1+982 km indicates that average cutter consumption rate is 35.7 m3/replacement (4.6 m/replacement). Cerchar abrasivity index and uniaxial compressive strength does not indicate any meaningful relationship with cutter life. Penetration per revolution and field specific energy might be used for predicting lives of constant cross-section double disc cutters. However, additional data is required to generalize the findings of this study. INTRODUCTION Cutter life / replacement and/or consumption rates in terms of cutter cost and replacement time loses is one of the most important parameters affecting excavation performance of mechanical excavators, especially of TBMs used very widely and equipped with usually disc cutters. Predicting cutter cost is a very important task in especially feasibility stage of tunneling projects. Basic parameters affecting cutter life can be classified into 3 general groups as geological and geotechnical, excavation machine (TBM) related, and operational parameters (Bilgin et al., 2013). The geological and geotechnical parameters are the most dominant ones among them. The machine related parameters should be arranged in accordance with the expected geological and geotechnical conditions for the best TBM excavation performance and minimum cost."

Jan 1, 2016

By R. P. King

The MODSIM mineral processing plant simulator is used to find optimal combinations of target separation specific gravities in a typical modem coal washing plant. A plant that is set up with these optimal targets can deliver up to 10% more yield at the same ash content as the same plant set up with separation targets chosen by conventional methods. MODSIM is the only simulator currently available that can simulate the liberation of pyrite and other mineral matter during open-and closed-circuit grinding operations. The simulator can therefore be used to assess the benefits of grinding operations in the flowsheet.

Jan 1, 1997

By C. M. Bartley

Canada has been a producer of sulphur in various forms for about 100 years, Pyrites, as a source of sulphur dioxide for the manufacture of sulphuric acid, were being mined in the 1860's. Smelter gas, for the same purpose, has been recovered since 1928. Between 1935 and 1943, and from 1952 to the present, elemental sulphur has been produced in Canada from two raw material sources and by several methods. This paper attempts to present a view of the current status of the elemental sulphur industry in Canada based on the sour gas fields of Alberta and British Columbia. Production from this source has increased rapidly in the past 12 years to make Canada one of the major sulphur producers of the world. The present industry in Canada relies mainly on sour gas sulphur and it is expected that it will continue to grow in the future. However, before describing current activity relating to sour gas it may be of interest to outline briefly the early pyrite activities, the roots of the sulphur industry in Canada.

Jan 1, 1964

By Paul W. McGann

This paper presents a methodology for long-range studies of petroleum supply, to meet projected demands, that involves modifications of procedures used previously. This paper continues a series of papers on this general topic in the AIME, the most elaborate recent one being that by Warren Davis given in February 1958. The procedures considered here begin with the assumption that the governmental framework of regulations and taxes remains fixed- but that price changes. After .these procedures have been reviewed, the effects of changing certain governmental controls, will be considered in order to judge their potential effects on future supply. This is an essential step because controls cannot be expected to' remain static in a situation changing as much as the petroleum. industry and because such changes are within-the scope of alternative ways of adjusting to impending problems. The first procedure begins with: a) trends in drilling success, b) relation between field income from oil and gas and footage drilled, c) declines in capacity from production, d) trends in capacity of new and producing wells, e) all monetary values are in constant 1958 dollars, and f) target amounts of domestic crude petroleum production. 'From these components projections are obtained of: 1) numbers of future producing wells required, 2) footage drilled, 3) new wells drilled, 4) crude oil found, 5) capacity of producing wells, 6) completion costs, 7) finding costs, 8) production costs, and 9) average wellhead crude oil price consistent with the footage-field income relationship.

Jan 1, 1960

The National Mining Hall of Fame and Museum will hold its Ninth Annual Induction Banquet Sept. 8, 1996, at the Las Vegas Hilton Hotel. Six mining greats, two of them living, will be enshrined at the event. They will join 126 other mining legends previously honored by the hall of fame. The keynote speaker will be William Perry Pendley, president and chief legal officer of Mountain States Legal Foundation in Denver, CO. Jeffrey Zelms, president and chief executive officer of The Doe Run Co., will be master of ceremonies. Richard Swayne, regional director USA for Boart Longyear Co. of Salt Lake City, UT, will introduce the speakers. Thomas Falkie, president of Berwind Natural Resources Corp. and chairman of the Mining Hall of Fame’s board of governors, will enshrine the inductees.

Jan 1, 1996

By J. A. Herbst

It is widely recognized that Semiautogenous Grinding (SAG) circuits require the use of effective process control techniques to achieve their full processing potential and to protect them from the harmful effects of overloads and grind-outs. This requirement is even more essential as the variability of the ore being processed increases. The new Chino Mines Company concentrator located near Santa Rita, New Mexico started operation in June of 1982. At least eight major rock types are mined and milled. Ore hardness, feed size, and specific gravity are quite variable. Typical feed rates per grinding line are 850-900 tph but extremes of 260-1200 tph have been encountered. Normal feed rate variations of between 400 and 1100 tph are encountered on a weekly and sometimes daily basis. Feed size varies with rock type from a maximum of eight inches for the harder ores to two inches for the softer ores. One somewhat unique characteristic of the Santa Rita ore body among major copper mines is the wide variation in ore specific gravity. Specific gravities of the major rock types range between 2.7 and 3.6. The specific gravity variations are due to large changes in magnetite concentration throughout the pit. The result of this is large variations in SAG mill throughput which can have a harmful effect on downstream ball milling and flotation performance. Due to these wide fluctuations in ore characteristics, it was recognized soon after startup that successful operation of the grinding circuit and the plant at large was dependent upon the development of an effective automatic grinding control strategy. Research at the University of Utah has suggested that control based upon critical but difficult or costly to measure variables would improve automatic control performance. A project team made up of the Chino process control staff, Kennecott's Process Control department and the University of Utah Metallurgy Department was established to assess these concepts at Chino. This paper describes the development and on-line plant implementation of an Extended Kalman Filter that uses simple models of the SAG milling process, to predict the volumetric loading, the rock mass, the water mass, and the ball mass within the SAG mills at Chino. The on-line estimation of these parameters is the first step in the development of an integrated SAG mill/ball mill control strategy which is hoped to L eventually maintain the grinding circuit at its maximum capacity, while balancing the grinding load between the SAG and ball mills. Examples of long term estimation with the models and filter are shown for typical operating conditions as well as a SAG mill overload and grind-out.

Jan 1, 1983

By G. A. Parkison

The sequential copper analysis method is a particularly useful technique to semi-quantitatively define the geologic, mineralogic, and metallurgical types and zonations commonly associated with porphyry-type copper deposits. The method is based on the partial dissolution behavior displayed by the prevalent copper minerals malachite, chrysocolla, chalcocite, and chalcopyrite to solutions containing sulfuric acid and sodium cyanide. Results from sequential analyses of the sample and analytical residue using sulfuric acid followed by sodium cyanide and then aqua regia solutions when compared with conventional total copper analyses can determine the amounts of leachable oxide minerals, leachable secondary sulfide minerals, and primary copper minerals, respectively. Sequential assay analytical results and interpretation are presented for copper deposits in Chile, Mexico, and the United States.

Jan 1, 1995

By P. O. Ripley

Into this tumultuous twentieth century, every second, two new babies are born. This is 5,412 per hour, and 130,000 per day. Relentlessly, consistently, alarmingly, they add to the more than three billion human beings who already inhabit the earth. Every tick of tier clock brings with it a problem child, the problem of another mouth to feed, another body to clothe, another human being for whom to provide. On the other hand, medical science has achieved a postponement of death, considerably past the period of a few years ago. Thus, life expectancy has been increased and world population has increased accordingly. Darwin (4) writing in 1962, suggests "It is curious how long the world is taking to perceive that we are living in what is a fantastically abnormal period of history, and one which must inevitably end soon, The first warning note of a possible population explosion was given by Malthus in 1799". He suggested that population increases geometrical while production increases only arithmetically and that soon we would not be able to feed the rapidly increasing population.

Jan 1, 1966

By Felicia F. Peng

Using granular media for removal of soluble manganese from mine water and industry waste stream has the advantage of forming a compact surface layer of manganese oxide coating on the media. This process can avoid the step involving the separation of voluminous sludge of manganese hydroxide by the high-pH method for soluble manganese removal. The removal of soluble manganese is accomplished by adsorption and oxidation. The adsorption of Mn(II) on the manganese oxide-coated media was rapid through the specific adsorption and may be due to the ion exchange of hydroxyl ions on the manganese oxide by Mn(II). In the subsequent step, the adsorbed Mn(II) form the intermediate manganese complex on the manganese oxide product is oxidized with dissolved oxygen or other available oxidant source in the aqueous solution. This paper presents the efficiency of removal of soluble manganese from mine water by using a laboratory fluidized bed and the recovery of manganese oxide coating on the anthracite coal particles. In order to accelerate the formation of the manganese oxide layer on the surface of anthracite media, dilute potassium permanganate solution is used as an active oxidant. The effects of operation parameters on the manganese removal including pH, flow rate, concentration of feed and oxidant dosage are evaluated.

Jan 1, 1996

By H. Melama

The primary grinding stage in the Vuonos concentrator comprises a rod mill in open circuit and a semi-autogeneous mill in closed, circuit with a hydrocyclone classifier. The instrumentation of the grinding circuit is displayed in Fig. 1. All the measurements have computer interfaces and all the control circuits have been implemented by the process control computer. The crushed ore feed to the rod mill is measured by a belt-weigher and controlled by a belt-feeder. The pulp density in the rod mill is stabilized by proportioning the waterfeed at the mill inlet to the crushed ore feed. The slurry level in the pump sump is measured by a pressure transducer and it is controlled by charging the speed of the direct-current drive pump.

Jan 1, 1984

By R. Mensah-Biney

The kinetics of gold-bromide loading onto activated carbon has been investigated in a batch stirred reactor. The amount of gold adsorbed by the carbon was correlated with time based on a second-order equation. The rate constant for gold-bromide species onto activated carbon ranged from 0.27 to 1.2 x 10-3 (kg/t)-l(min)-l from a solution containing 25 ppm of Au, with 0.8 g carbon per liter of solution at 30° C. The equilibrium saturation capacity (Q.) was 36±3.0 kg/t from the same system. The rate of loading increased with decreasing particle size, decreasing pH, increasing temperature, and decreasing concentration of gold in solution. The calculated activation energy E. was 8.8 kcal/mole, significantly higher than those reported for physical adsorption. The equilibrium saturation capacity (Q.) increased with increasing concentration of gold in solution, but was independent of other variables such as temperature, agitation speed, particle size and pH. These rate constants and equilibrium saturation capacity for the gold-bromide species are higher than those reported for the gold-cyanide systems.

Jan 1, 1996

By A. Kaina

The San Luis deposit is one of the few documented gold deposits on a detachment surface. This paper presents mineralogic and geochemical data that was gathered to characterize the mineralization, classify the ore deposit, and provide details of the ore forming process. Included are data on the paragenesis; alteration-mineral assemblages major and trace element geochemistry, and fluid inclusions. The San Luis deposit occurs on the western slope of the Sangre de Cristo Mountains adjacent to the San Luis Basin about 5 miles northeast of the town of San Luis in Costillo County, south-central Colorado. Mineralization was discovered in the district in the early 17th century. Production began in 1890 on lead-silver ores from which the district took the name the old name of "El Plomo". From 1897 through 1934 gold was intermittently produced. Battle Mountain Gold Company took an option on the property in 1987 and proved on ore body comprising an eastern block that has 1,277,300 t ore at a grade of 1.68 g/t and a western block of 9,744,000 t with a grade of 1.34 g/t. Production began in 1990. A companion paper by Benson (1994) describes the San Luis district and the ore body, hence the reader is referred to this or Robert and David (1990) for details of the geology from which the following is summarized.

Jan 1, 1994

By Paul Dean Proctor

The known northern ore zones of the New Lead Belt of Southeast Missouri extend to the drainage divide between the Meramec River draining north and east and that of the Black River draining southward. Intensive geochemical studies related to the environmental impact of the new mining area have been carried out in the vicinity of some of the newly developed mines, mills and smelter complexes (Bolter,1970; Gale, et al, 1973; Wixson, et al, 1969, 1977). Other investigations have related to fringe studies of the Northern New Lead Belt and the possible additions of heavy metals to the surface waters, stream sediments and selected aquatic life (Proctor, et al, 1975, 1976). Similar studies have been completed in the Joplin area in the Tri-State district, and in the fringe area near Springfield, Missouri (Proctor, et al, 1974). A surface geochemical study is currently underway on the lead-zinc-copper-cobalt-nickel province near Fredericktown, Missouri (Proctor and Sinha, 1977). This report summarizes some of the distribution patterns of heavy metals in the waters, stream sediments and selected aquatic life in the Upper Meramec River drainage basin just north and west of the known northern portions of the New Lead Belt of Southeast Missouri. The region studied includes the site of the proposed and somewhat controversial Meramec Dam and the reservoir site behind it. Some 3905 km2 (1508 mi2) are included within the drainage basin of the Upper Meramec River. Six distinct drainage areas are included within the drainage basin; 1) a combined, lightly industrialized and farm area around Rolla and Salem, Missouri representing the Dry Fork drainage; 2) a primitive, mostly forested area with some farms and cattle rancheseast and north of Salem, Missouri comprising the Upper Meramec River

Jan 1, 1977

By M. W. Smith

Pennsylvania has 2500 miles of streams that do not meet water quality standards due to acid mine discharge (AMD), making AMD the greatest cause of water pollution in the state. The problem is mainly caused by abandoned coal mines. Pennsylvania is using a watershed-based approach to abating AMD which includes remining as a key component of a comprehensive restoration strategy. The Tangascootack Creek Watershed was targeted for AMD restoration through remining. Geologic mapping and overburden data were analyzed using Earth Vision software to identify areas of coal reserves which could be remined to improve water quality. Incentives are offered to encourage mining in these designated areas.

Jan 1, 1999

By H. Rush Spedden

A process has been developed and piloted to reject copper, lead, iron, phosphorus, bismuth, antimony, elemental sulfur, and insol from molybdenite concentrate without decomposing the contained molybdenite and rhenium. The impure concentrate is first heated with concentrated sulfuric acid at 260 to 290°C for 1 hour. This bake not only oxidizes the contaminating sulfides, but also activates the concentrate for later rejection of insol by flotation. Two stages of leaching follow the sulfation step. The first is an acidified water leach which extracts the oxidized copper, iron, and phosphorous; the second leach rejects the lead, bismuth, and antimony into a warm concentrated solution of sodium chloride. Final upgrading is achieved by conventional froth flotation. The chemistry of the process as well as results obtained from its implementation in a 5,000 lb/day pilot plant are presented.

Jan 1, 1971

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,300 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, the deposits are divided into several mining zones. The geotechnical properties of mining zones are also different from one zone to another. A successful geotechnical collection system is very important for the mining designs and operations in the Leeville underground mine.

Jan 1, 2010

By Joseph Moses Botbol

Two methods are developed whereby; (1) mineralogic data can be arranged in order of typicality, and (2) mineralogic data external to a model can be compared with the model and the degrees of association computed. Thirty arbitrarily selected base metal mining districts in the conterminous United States were classified as copper, lead, or zinc districts on the basis of tonnage of the major base metal produced. For each of the copper, lead, and zinc districts binary-occurrence distributions were compiled for primary (unoxidized) and secondary (oxidized) minerals. Primary and secondary minerals were then arranged in order of decreasing typicality. Model copper districts are most typified by primary chalcopyrite, pyrite, and secondary malachite. Model lead districts are most typified by primary galena, quartz, pyrite, sphalerite, and secondary anglesite and cerargyrite. Model zinc districts are most typified by primary sphalerite, galena, pyrite, quartz, and secondary smithsonite and cerus-site. The Park City district was removed from the model and its primary and secondary mineralogy was compared with the model copper, lead, and zinc districts. The primary mineralogy of the Park City district is about equally associated with the model copper and lead districts, but the secondary mineralogy is much more akin to the model copper districts. Thus, with respect to the model data, the geochemical target presented by the Park City district resembles a copper district more closely than a lead district.

Jan 1, 1969