Search Documents

By Nick Barton, Khosrow Bakhtar

Two plate load tests of 1 m2 area were per- formed in a pressure tunnel at the Rocky Mountain Pumped Hydro Project. Reaction for the 250 tons loading in this 10.5 meter diameter tunnel was provided by deeply anchored, diverging rock bolts, eight per load frame. Pressure build up to 2.5 MPa was provided by circular flatjacks. Rock deformation was recorded at depths of approximately 0.3, 0.9, 1.2, 1.8 and 3.3 meters using axially located multiple position borehole extensometers. The tests were performed in representative units of massive shale and thin to medium bedded siltstone. Stress was built up in four equal steps to 2.5 MPa, held constant for one week for creep monitoring, then unloaded, reloaded and unloaded over a period of one day. The most deformable unit was the massive shale which exhibited 1.3 mm of permanent deformation at the surface after the first loading and unloading cycle, which included 0.36 mm of creep. After the second loading-unloading cycle, the permanent deformation had increased to 2.6 mm, following a maximum deformation at the surface of approximately 3.6 mm. At the maximum stress of 2.5 MPa, the tangent modulus averaged 0.4 GPa when loading, and 0.3 GPa when unloading. The thin to medium bedded siltstone exhibited only 0.17 mm of permanent deformation at the surface after the first loading-unloading cycle, which included only 0.05 mm of creep. After the second loading-unloading cycle, the permanent deformation had increased to 0.27 mm, following a maximum deformation at the surface of approximately 0.53 mm. At the maximum stress of 2.5 MPa, the tangent modulus averaged 6.2 GPa when loading and 21.9 GPa when unloading.

Jan 1, 1986

By A. D. S. Gillies

The use of refuge chambers for use in handling underground emergencies is an issue of topical relevance within the US mining industry. Chamber design is of importance to meet some new safety requirements of US federal and some state government mine regulations. A review has been undertaken of a steel mine refuge chamber design to predict what will be internal temperature within the chamber over an extended period with miners present? The design has been examined for the situation when the chamber is sited in still mine air. Spreadsheets have been developed to allow various design assumptions to be tested. The evaluation has been undertaken using thermodynamic heat transfer models with some assumptions specified to produce a model of appropriate simplicity but with adequate degree of accuracy. Under normal still air conditions it can be seen that internal chamber conditions rise quickly to often arduous conditions. There will always be quite a few assumptions necessary in complex heat transfer process evaluations. Some important refuge chamber design parameters are: ? External surface area of the chamber, its wall thickness and construction. ? Metabolic heat generated and number of persons making use of the chamber. ? The temperature of the external mine atmosphere to the chamber over the year and the influence of geothermal gradient on temperature at depth. ? The maximum internal chamber Apparent Temperature considered safe. ? The distance inside the underground mine and adjacent ventilation conditions.

Jan 1, 2012

By J. F. T. Agapito, G. P. Bratton

A 16 m by 4.7 m by 24.5 m (52 ft by 15.5 ft by 80.5 ft) underground ore bin was constructed at an 810 m (2660 ft) overburden depth in poor quality, faulted and altered intrusive rocks at Molycorp's block caving molybdenum mine. Geological engineering incorporated detailed structural mapping, rock quality classification, in-situ stress field determinations, numerical stress and failure analysis, and convergence monitoring. The ore bin was mined by conventional methods from the top down and utilized a bored raise for mucking. The initial ground support of rock bolts, lightweight steel sets, and reinforced concrete was later supplemented with an array of 6, 12 and 21 m tensioned, grouted rock bolts when wall closure was noted in the upper ore bin area. The supplementary support was optimized by computer analysis and monitoring.

Jan 1, 1985

By Wilhelm Knickmeyer, Johannes Henneke

PREFACE For about 1 year Bergbau-Forschung GmbH, central research institute of the German Coal Mining Industry, undertakes full size tests for waterjet assisted tunnel¬boring in German coal mines (Fig. 1). These tests are performed with a tunnelborer of 2.6 m diam in an upper [ ]

Jan 1, 1979

By D. S. Kieffer

Ground characterized by hard boulders embedded in soft matrix represents one of the most challenging conditions for TBMs, as the cutterhead must cope with the non-optimal conditions of cutting hard blocks while simultaneously excavating through soft, soil-like matrix material. Dowden and Robinson (2001) and Hunt and Mazhar (2004) summarize several case histories relating to the problems of advancing a TBM through boulder-laden ground and provide guidance with respect to appropriate site investigations and baselining strategies. Some rock types constituting boulder-laden ground include: ?Sedimentary Rocks?cemented alluvial channel deposits, colluvium/talus, landslide debris, and glacial till. ?Igneous Rocks?agglomerates, lahars, and pyroclastic deposits. ?Metamorphic Rocks?tectonic mélange and cataclastic fault zones. ?Decomposed Rocks?corestone bearing saprolites. Disc cutters are commonly utilized to cut the hardblocks; however, as compared to the understanding of disc cutter behavior in hard continuous rocks, little is known regarding fundamental cutting mechanisms in highly heterogeneous bouldery ground conditions. To advance this understanding, a suite of full scale tests have been performed using a linear cutting machine at the Colorado School of Mines (CSM). This paper summarizes the observed cutting mechanisms and their practical implications for TBM excavations through boulder-laden ground.

Jan 1, 2008

By Emad Iskander

The seepage forces generated around pressurized water tunnels in rock are investigated using the analysis tools of geomechanics. The theoretical background of the two-phase material behavior is explained and the equations of motion and continuity are presented. Applications on two case studies typically occurring in practice deal with the required minimum rock cover for a pressurized tunnel and the separation between two tunnels carrying different heads. The rock mass behavior as described by the Mohr-Coulomb and Hoek-Brown material models is investigated by numerical analyses and the results are compared. The effect of key material parameters on the safety factors and the associated modes of failure is discussed.

Jan 1, 2008

By Bhaskar B. Thapa, Michael T. McRae, Johannes V. Greunen

This paper describes the preliminary design of the fourth bore of the Caldecott Tunnels along State Route 24 in Oakland, California. The paper focus is on two major aspects of the project: initial support system design and seismic design. The initial support system was designed based on the New Austrian Tunneling Method (NATM).NATM provides the required flexibility to accommodate the variable ground conditions in the weak, folded, and faulted rock along the alignment. The seismic design provides a final lining system that meets serviceability requirements for a 1,500 year seismic event with an estimated peak ground acceleration of 1.2g.

Jan 1, 2007

By K. Saikiran, A. R. Nalla

Longwall management, regular shield maintenance, and evaluation of ground control problems can be performed using real-time shield monitoring program. Based on real-time shield pressure data, evaluation of intensity and interval of periodic weighting, estimation of time-dependent pressure increase and the effects of geologic anomalies can be obtained. In this study, full-face shield pressure data of over 457 m (1,500 feet) of face advancement is analyzed to evaluate shield response in the presence of surface lineaments, floor undulations, and multiple main roofs. Shield pressure increase due to web cutting is also correlated with setting pressure during periodic weighting and normal time. In addition, time-dependent pressure increase rate on Sundays and holidays is also correlated with time average pressure and the location of previous periodic weighting.

Jan 1, 2000

Editor?s note: Each year, the June issue of Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue. Thank you to the industrial minerals annual review editor, to the technical committees chair and vice-chair, and to the authors of the individual commodity profiles. Jim Norman, member SME, of GeoTrans, Inc., is the industrial minerals annual review editor. SA Ravishankar, member SME, of Cytec Industries, is chair of the industrial minerals technical committees. Technical committee vice chairs include: ? Abani Samal, member SME, of Pincock Allen & Holt, agricultural minerals. ? Aaron McMahon member SME, of Pincock, Allen & Holt, ceramics and refractories. ? Bradley S. Van Gosen, member SME, of the U.S. Geological Survey, chemical raw materials. ? Mark Zdunczyk, member SME, of Continental Placer, Inc., construction materials. ? Jerry Gauntt, member SME, of JEG Minerals Consultants, fillers and pigments. ? Michael Cheshire, member SME, of Indiana University, sorbents, filters and process aids. Their help makes possible this June industrial minerals issue. On behalf of ME readers, the editors thank them.

Jan 1, 2008

By L. B. Hales

Expert control of grinding and flotation plants has been successfully used in the minerals industry since the 1970?s. The earliest of these systems were written in a hard-coded fashion in FORTRAN, BASIC or Pascal. Second generation systems were built using the first experimental expert system shells that were being developed in the artificial intelligence community. Later systems were deployed in expert system shells designed for real-time processing plants that also included the ability to model the process with neural network models and optimize setpoint selection through the use of genetic algorithms. Significant performance increases have been achieved using these systems, but in general, they suffer from the static nature of their rules and to a degree the process models also. Typical improvements quoted in the literature suggest throughput rate increases of 4 to 8 percent and recovery increases of 1 to 4 percentage points. In over 30 years of designing and installing expert systems we have never seen performance numbers less that these but have often seen numbers in excess of the high values. However, once the system has been installed and tuned up the performance usually does not improve much thereafter. Granted, the initial increases in throughput rate and recovery are significant but a question always lingers, that is, can the expert strategies be modified further to squeeze a little more improvement out of the system. The answer to this question is a resounding yes, however a complete understanding of what we do well as designers and operators of expert control systems is required as well as how we can improve upon our best practices is required to move us from the performance plateau we have been on for a number of years to a new higher level of performance.

Jan 1, 2009

Barrick Gold plans to have four new gold mines in production by 2006. Together, the mines would increase the company’s output by 40 percent. The projects include Veladero in Argentina, Alto Chicama in Peru, Cowal in Australia and Tulawaka in Tanzania. All of them are scheduled to begin production between the first quarter of 2005 and the first quarter of 2006. They are expected to drive Barrick Gold’s growth profile to a target of 211.5 to 217.7 t (6.8 million to 7 mil-lion oz) of gold production in 2007. The company’s projected output for 2004 is 152.4 to 155.5 t (4.9 million to 5million oz) in 2004. Overall, higher production and lower costs are expected in the early years from the new mines.

Jan 1, 2004

By Alejandro Gutiérrez, David Ahues, Paola Merino, Felipe González

A Discrete Elements Method (DEM) study of load movement within a SAG mill 12,192 × 7620 (40′ × 25′) in normal operating conditions is performed. The purpose is to determine how the geometry of the lifters affects the kinetics of the load inside the mill. Specifically, the changes produced by the incorporation of inclined lifters and spiral or helicoidal pulp lifters to the kinetics are evaluated. Four study cases are identified: first, the base case corresponds to a conventional geometry; the second case corresponds to inclined lifters incorporation; third case corresponds to a mill with helicoidal discharge; and the fourth case corresponds to a mill with inclined lifters and helicoidal pulp lifters. To save computational resources, the water that enters the mill has been modeled by varying the coefficient of restitution. The results of a series of experiments are presented to determine how this coefficient varies when having impacts on surfaces with different liquid levels. A comparative analysis is made of the following variables: mean transport speed and material flow, for normal operating conditions. Taking as reference the mill with straight lifters and radial pulp lifters (case 1), the case with the inclined lifters and radial pulp lifters increases the material discharge flow less to 76 mm of size by 5.1%, and this value increases even more when the helicoidal pulp lifters are incorporated reaching a 58.6%. The most significant change is seen in the flow through the grates and the pulp lifters discharge, which can increase substantially improving the operation.

By D. Rahal

All ores have an economic optimum particle size (Wills and Napier-Munn, 2006). This optimum value is often a compromise between the need to achieve adequate liberation for the efficient separation and recovery of valuable minerals and the energy consumed by the crushing and grinding process. It has been recognized for nearly three decades that grinding is the most expensive and least efficient stage in mineral processing (El-shall and Somasundaran, 1984). At that time it was estimated that grinding consumed between 25 and 70% of the total power required in mineral processing. This recognition drove the development of new stirred mill fine grinding technology in the 1990s (Jankovic et.al, 2003; Enderle et. al., 1997; Massey, 2008). These milling technologies have a reduced energy consumption compared to traditional fine grinding using ball mills. In the ?coarser? fine grinding applications this improvement is approximately 30%. The benefits increase to above 50% in ultrafine grinding applications (Lichter and Davey, 2006). Despite these gains, the US Department of Energy reported that an additional energy savings of up to 37% is possible in the minerals industry. They identified continuing research and development and implementing best practices in both grinding and materials handling as the primary avenues for the additional reduction (BCS, 2007).

Jan 1, 2011

By Yifan Ding, Shemek Oginski, Patrick Finn

The Manhattan section of the New York Water Tunnel No. 3 constructed by the Schiavone/Shea/Frontier-Kemper Joint Venture is a $668 million project. The contract includes a tunnel drive of 8.85 km (29,045 feet), tunnel lining of 14.77 km (48,468 feet)and construction of nine shafts ranging in depth from 143 m (469 feet) to 169 m(555 feet). Construction methods for excavation of the shafts are presented including raise bore, ground freezing, soil excavation, blasting, slashing, muck handling, rock support and shaft final concrete lining.

Jan 1, 2007

By R. L. Unger

Restricted fields of vision are a common problem with underground mining equipment. Also, when lighting systems are provided, they may be positioned where they cause glare. This restricts the visibility around the machines even further. To help address these problems, the U.S. Bureau of Mines has developed a PC based software package to aid in the analysis of certain human engineering aspects of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines.

Jan 1, 1994

By Andy Alder

The Docklands Light Railway (DLR) Extension to Woolwich Arsenal provides a much-needed public transport link to this area of London. The project includes construction of 5.3mID running tunnels under the River Thames, in ground conditions that proved challenging for the Earth Pressure Balance Tunnel Boring Machine (TBM). The project also includes cut and cover tunnel approaches, an underground station, and an emergency shaft on the bank of the river. Major challenges have included tunneling under sensitive infrastructure, and working adjacent to existing operational railways at Woolwich Arsenal. This paper will describe the design and construction of the project and how these challenges were overcome.

Jan 1, 2008

By Douglas R. Cook

Exploration record In preparing this paper, a list of world class discoveries prepared in 1983 has been updated. In both surveys, the following criteria were used in the definition of world class discoveries: • deposits that are continuously operated and consistently return a profit even in periods of low metal prices; • deposits large enough to significantly affect a medium sized corporation's profits; and • these deposits should be in the lower one-third cost per unit of metal produced for all similar deposits. Only 70 discoveries in the last 40 years qualified as world class deposits using these criteria. Unfortunately, this restricted population was too low to develop meaningful trends. The numbers were therefore enlarged to include all significant discoveries. The principal feature of a significant discovery is that its size and grade would yield more than $500 million in revenue using average metal prices for the last five years. A significant deposit should also meet some of the standards for a world class deposit. A tabulation of these deposits are shown in Table 1. The number of discoveries increased to 166 from 70 using the revised classification. The relationship between the number of discoveries per year and their location by continents was prepared from these data. Figure 1 shows the number of discoveries per year for the nonCommunist world. It also shows estimated and actual nonCommunist world exploration expenditures per year and the commodity price index. These data show that modern exploration started in the late 1940s, with the tempo picking up rapidly in the 1950s. The maximum discovery rate occurred in 1962. Thereafter, the discovery rate gradually declined to the present. This occurred despite a real increase in expenditures from about $200 million/a in 1955 (1982 constant dollars) to more than $900 million/a in 1980. Thus, these data suggest a significant decrease in the exploration success ratio (total exploration expenditures a year divided by the number of significant discoveries) in the last 20 years. As an example, $70 million was spent for each significant discovery in the early 1960s as compared with $225 million in the late 1970s (expressed in 1982 constant dollars). However, with the general declining trend of discoveries, one can perceive a more pronounced drop in 1973 and then a sudden increase in 1974, 1975, and 1976. This increase is probably related to the inflation of the 1970s that in turn created an environment for the explosion of commodity prices, as shown by the commodity price index on Fig. 1. Thereafter, the decline in discoveries resumed in 1975 until the present. Exploration performance by regions North American discoveries are shown in Fig. 2. The graph shows three pronounced high discovery peaks in 1962, 1975, and 1980-81.

Jan 2, 1986

By G. Abramov

The 20th Century saw the modern mining industry enriched by one outstanding method of extracting of mineral resources called Borehole Mining (BHM). Mean while, despite its successful track record in wide ranging locales, few specialists are yet aware of this technology. The intent of this article is to introduce borehole mining to a wider spectrum of drilling and mining professionals. The BHM method is based on in-situ water jet cutting of rock mass. On Fig. 1 the schematic of the method is presented. The borehole mining tool 1 is lowered into the borehole 2 and high pressure water 3 is pumped down. At the bottom part of the tool, one portion of that water comes out through the hydromonitor nozzle 4 in a shape of water jet 5 and cuts the material 6 creating slurry 7. The other portion of high pressure water then comes to the hydroelevator 8 (jet pump, eductor) which produces a vacuum. When the slurry reaches this vacuum zone, the eductor sucks the slurry and pumps it up to the surface, where rock parts are separated from water in a tank 9 or a pond and clarified water is pumped down again closing the re-circulating BHM water supply system. The borehole mining tool is suspended on a drill rig tower 10 which allows the tool to rotate and move vertically along the borehole axis. While extracting rock mass, underground caverns (stopes) 11 are created. If necessary, compressed air 12 can be injected to the raising slurry flow to create an airlift effect. Also, a secondary agent 13 (such as oil, foam, etc.) can be added to the stope through the gap between the tool and the casing. As seen from the illustration, BHM is the remote mining method of extracting of mineral resources through boreholes by high pressure water jets.

Jan 1, 2001

By Bradford F. Townsend

A study was made on six collapses that occurred during large-diameter tunnelling through weak sedimentary rocks and soil using SES methods in three stages?top heading, bench and invert. The collapsed lengths are between 20 m and 277 m. The collapses were re-mined using essentially the same tunnel-ling method with larger excavation profiles to accommodate the designed remedial measures consisting of ground treatment, pre-support and stronger initial support/outer lining required to carry higher ground loads acting in the collapsed lengths. The paper presents information on the collapses and the design and execution of the remedial measures.

Jan 1, 2008

By Verya Nasri

The proposed Second Avenue Subway Project in New York City is approximately 8.5 miles long, up to a depth of 120 feet beneath grade and runs the length of the eastern side of the island of Manhattan from Harlem in the north to the financial district in the south. It will reduce overcrowding and delays on the existing parallel line, improving travel for both city and suburban commuters, and upgrading access to mass transit for residents of the East Side of Manhattan. This subway line will have 16 new stations providing transfers to the existing Metro-North commuter rail service and to New York City Transit subway lines and bus services. The first phase of construction includes two TBM rock tunnels 2.4 miles long and two new large and shallow rock cavern stations with clear span openings ranging from 70 to 100 feet and length in excess of 1000 feet with 615 feet center platform, coupled with low rock cover ranging from 20 feet to 40 feet. The design methodology for these large and shallow rock caverns consists of using well known empirical methods for initial estimate of support requirements and then two and three dimensional continuum and discontinuum analyses for verification of the selected excavation sequence and support system. This paper describes the analysis and design methodologies used for the two large and shallow rock caverns with insight into how to overcome the design complexities and construction challenges of the urban underground.

Jan 1, 2008