Search Documents

By M. Nehdi

Deficient surface disposal systems of sulfidic mine waste often cause severe contamination of surface streams and groundwater reservoirs due to the oxidation of sulfide phases. The subsequent generation of leachates characterized by high acidity and elevated concentrations of toxic elements (commonly known as acid mine drainage) jeopardize the health of contiguous ecosystem. Stabilization/solidification (S/S) is recognized as a promising solution for treating such wastes. S/S processes generally mobilize alkaline and/or cementing materials/additives that act as neutralizing and/or binding agents. In the present research, industrial byproducts, namely, cement kiln dust (CKD) and Class C fly ash (FAC) have been used as candidate materials along with the partial addition of sulfate-resistant cement (SRC) in the S/S of polymetallic sulfidic mine tailings (MT). The effectiveness of S/S was assessed by comparing laboratory experimental values obtained from unconfined compressive strength, hydraulic conductivity and leaching propensity tests of S/S samples with regulatory standards for safe surface disposal of such wastes. Despite general regulatory compliance of compressive strength and hydraulic conductivity, some solidified/stabilized-cured matrices were found unable to provide the required immobilization of pollutants. Solidified/stabilized and 90-day cured mine tailings specimens made with composite binders containing (10% CKD + 10% FAC), (5% SRC + 15% FAC) and (5% SRC + 5% CKD + 10% FAC) significantly impaired the solubility of all contaminants investigated and proved successful in fixing metals within the matrix, in addition to achieving adequate unconfined compressive strength and hydraulic conductivity values, thus satisfying U.S. EPA regulations. Laboratory investigations revealed that, for polymetallic mining waste, leachate concentrations are the most critical factor in assessing the effectiveness of S/S technology.

Jan 1, 2008

By H. Akgun

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. This paper presents the results of push-out tests on cement grout plugs in salt. Two expandable cement grouts have been tested. The average interface shear strengths ranged from 2 to 12 MPa. Peak shear stresses at failure, assuming an elastic stress distribution along the interface, were up to eight times higher. Standard deviations commonly reached 20%. Dissolution along the interface was observed, and may have been enhanced by clay inclusions in the salt. This dissolution appears to have reduced bond strengths. Application of the results to the design of plugs for larger openings (e.g. shafts, drifts, or boreholes) is discussed.

Jan 1, 1991

By K. Donahue

Clay minerals play an important role in the gravitational stability of man-made rock piles by affecting geotechnical and hydrological characteristics of the material. The Goathill North rock pile at the Questa Mine in northern New Mexico has been the focus of a multi-disciplinary study to determine the effect of weathering on rock pile stability and in particular to determine if clay minerals are forming in the rock pile due to surface weathering. The results of x-ray diffraction (XRD) and scanning electron microscopy (SEM) analyses indicate the clay minerals found within the fine-grained soil matrix of the rock pile are of hydrothermal origins and did not detect any neoformation of clay minerals. The foremost mechanism for an increase in clay minerals within the rock pile is the physical break down of hydrothermally altered rock fragments to release hydrothermal clay minerals. The hydrothermal clay minerals within the rock pile show evidence of weathering by the dehydration of smectite from 2-water to 1-water interlayers within the clay mineral structure. This dehydration is most likely due to higher temperatures and low relative humidities in the Goathill north rock pile during surface exposure.

Jan 1, 2009

By Manchao He, Xiaoding Xu, Yubing Gao

Based on the geological conditions of the 15,600 working face in Pingba Mine, this paper establishes the mechanical model of the stress distribution in the pre-working face under the influence of mining pressure based on a hemispherical stress distribution theory. The analytical formula for the stress distribution is determined. A numerical model for the mining pressure under the influence of key layer is also constructed, and dynamic stress interruptions under various roof-cutting relief schemes in different horizontal positions are simulated. The stress distribution of the stope under different pressure relief schemes is analyzed and compared with the theoretical results. Results show that blasting roof cutting blocks the transmission of the abutment pressure to the working surface to the coal and rock mass in front of the working face, reducing the significant working face mining pressure influence range, which decreases as blasting pressure relief position moves toward the working face. Stress accumulation in the coal in front of the working face also increases as the blasting pressure relief position moves toward the working surface. Engineering practice results show that blasting cutting can effectively block the propagation of mining pressure, and the stress impact range is shortened by approximately 1/3.

Jul 31, 2021

By S. Yerel

In a mineral processing plant, the determination of a preventive maintenance schedule is one of the most important maintenance policies. In this study, to determine the preventive maintenance schedule for the Emet Colemanite Mineral Processing Plant in Turkey, a mean quality control chart was constructed using the historical concentrate B2O3 grade data. The effect of preventive maintenance scheduling on B2O3 grades was monitored using the mean quality control chart. It was determined that recovery increased after each preventive maintenance scheduling. Close examination of the mean quality control charts indicated that there were three periods that showed different grade characteristics. These were identified as the period ?prior to preventive maintenance,? the period ?after preventive maintenance? and the period ?requiring preventive maintenance.? These periods were compared as two independent samples by using the Kolmogorov-Smirnov test. Application of this test for interpretation of the mean quality control chart enabled the authors to analyze the system effectively, and it showed that the preventive maintenance for this plant should be scheduled at four-month intervals.

Jan 1, 2007

By Thomas J. DeMull

Development of the Batu Hijau copper project was completed in the fourth quarter of 1999 with the formal handover and start-up of ore processing facilities. The project began in August 1996 when the owner, PT Newmont Nusa Tenggara (PTNNT), awarded an engineering, procurement and construction (EPC)contract to Fluor Daniel (FD) for the development of the project. This included a copper concentrator, port, power plant, town site and infrastructure. PTNNT managed the development of the mine and the procurement of the mine equipment. In 1996, Batu Hijau was the largest mining project ever undertaken. Developing the Batu Hijau Mine was complex. It involved the work of thousands of people in all parts of the world to plan, engineer, procure, fabricate and manufacture equipment, supply and deliver materials and equipment, and build the plant.

Jan 1, 2002

By A. H. Shapiro

A decanter centrifuge of novel design was developed for the dewatering of fine-solids slurries having micron-range particles that form paste-like, flowable, hard-to-dewater cakes. The design combines a compound beach with a cake-flow control structure that allows expressed liquid from the cake in the dry beach region to be returned back to the liquid pool while maintaining high solids throughput. In order to provide optimal performance with various operating parameters (feed rate, centrifugal gravity, pool, differential speed, concentration of feed solids, and different slurry types), the cake-flow control is adjustable. The second part of the beach is preferably at zero angle. Tests showed that the new design allows increases in both solids dryness and solids throughput.

Jan 1, 2001

By Hendrick A. D. Kirsten, A. Clayr Alexander

Stillwater Mining Company is currently developing a second underground palladium and platinum mine approximately 21 km (13 miles) west of their existing Nye operation in the Bear tooth Mountains of southern Montana. Portals for the two access tunnels required at the new site were excavated in limestone talus to accommodate4.6 m (15 feet) diameter tunnel boring machines. A review of the technical design, field conditions and construction of the portals is presented.

Jan 1, 2001

This paper describes major technical developments in rod mill design and operating practice since its introduction into the North American minerals industry over fifty years ago. The basic operating characteristics of the wet, overflow rod mill are described, and significant operating variables are reviewed in terms of their effects on mill power draw, power efficiency, and practical aspects of circuit operation. Key factors for improving the economic performance of rod milling circuits are identified.

Jan 1, 1986

By Davar Abi-Zadeh, Cillian Brown, Deepak Kandra

"Grout backfill strategy for a particular subsurface concrete tunnel (~4.9km long, 3.5m in diameter, carrying 20” gas pipeline) was based on achieving 1:100 slope of the fill in order to progressively fill the tunnel, in a series of 350m section. Grout rheology, particularly its non-Newtonian and thixotropic behavior, determines the final fill slope for given backfill strategy. The objective of this study was to simulate the two-phase grout mix backfill process using Computational Fluid Dynamics (CFD) and determine the slope of the fill to validate and optimize the backfill strategy. Three dimensional CFD study showed that for a 500m long tunnel section with a single injection point of grout, given its rheology, it will likely keep flowing without filling the 500m section height wise. Design optimization for filling was carried out using two dimensional studies to make the backfill process “slope independent” by incorporating a 2.5m high bulkhead at ~1,000m. INTRODUCTION As part of a gas field development a 20” onshore gas pipeline is required from the landfall site to the processing terminal some 8km inland. At the landfall site the gas pipeline is routed in a ~5km underground tunnel underneath a bay. For operational reasons and planning consents as well as to mitigate environmental impact based on an environmental impact study, once the gas pipeline and the associated services and spares have been installed, the subsurface gas tunnel will be fully grouted. There will be no permanent access to the tunnel after construction is completed and the site compounds have been reinstated once works are complete. One of the key requirements is that “full grouting of the tunnel” is desired. The grouting material used is a non-Newtonian and thixotropic fluid mixture of bentonite, cement, plasticizer, retarder/stabilizer and water. The tunnel is filled progressively in 350m sections using a combination of existing and new pipework assuming the grout rheology will yield a fill slope of 1:100 in a 350m section. The proposed grouting system used one pump at the grouting compound to pump the grout into the tunnel using the existing tunneling pipework. For the longer runs a second booster pump was used in series to pump the grout to its final discharge location. The filling process is controlled via a system of flow meters, pressure transmitters and a tunnel CCTV system."

Jan 1, 2016

By George C. Toland

Most existing impoundment ponds and dams leak effluent into the soil or rock upon which they are constructed. However, proposed environmental legislation will require very stringent control on the release of toxic effluents such as cyanide. More exacting investigation, design, and construction techniques than have been used in the past will be required to satisfy these new regulations. This paper discusses the types of field and laboratory investigations required to develop the data for the design of an impoundment system containing toxic effluent, and discusses in detail technical considerations necessary to design this system. Design topics include reservoir sealing with natural and man-made materials; embankment sealing; embankment design considering stability, surface hydrology, capacity, and downstream catchment basins; and special implications of cyanide effluents.

Jan 1, 1975

By Cary Hirner, Sarah Lothman, Chris Mueller, Savita Schlesinger, Mike Hanna, Ian Fitz-James

Loudoun Water is currently implementing a quarry to reservoir conversion that will improve water supply reliability in periods of drought and flexibility in water supply operations when turbidity in its Potomac River supplies are high. The Milestone Reservoir Project consists of an inter-tie to the existing Potomac River Pipeline; new pipeline and tunnel; and a pumped intake and outlet works. Planned construction involves significant risks due to underground conditions which includes hard, igneous rock and high groundwater at the creek crossing. In addition, the site is constrained by Goose Creek, an adjacent residence, active mining in a quarry next to the new reservoir, public use of adjacent park space, and the Washington and Old Dominion Trail. Working with these constraints will require close coordination with active mining operations and public and private property owners. Safety of personnel involved with construction also represents a concern with quarry high walls over 30 meters in height near the planned construction. In consideration of key projects risks, Loudoun Water determined that an innovative CMAR delivery approach provided the best opportunity to achieve its goals in quality, innovation, front-end cost and schedule certainty, and operational flexibility and reliability. What matters most to Loudoun Water is the value in having a builder participate in the design process where key decisions can be made based on consideration of risks, cost, schedule, quality, and operability and maintainability of the system. While a progressive design-build delivery model may have produced similar outcomes, Loudoun Water had already invested in substantial development of the design for the work, and ultimately, CMAR provided Loudoun Water the opportunity to retain the partnership with the design team while gaining valuable input from a contractor. Among the challenges with CMAR in the Commonwealth of Virginia is a substantial limitation on self-performance corresponding to 10 percent of the construction value of the work. A significant industry outreach program was initiated by Loudoun Water to encourage participation with incentives in contract terms that allowed for the CMAR Contractor to make a reasonable profit. This paper reviews the CMAR procurement process and discusses contract incentives that were adopted to promote the work within the constraints of contract law in Virginia.

Jun 13, 2021

By Hasan Nizamoğlu, Z. Abidin Sarı, Aslıhan Demiraslan, M. Deniz Turan, Tolga Depci

In this study, recovery of copper from solid material (obtained by leaching of chalcopyrite with oxalic acid in the presence of hydrogen peroxide) with a copper oxalate structure was carried out selectively using HCl. The chemical composition of the solid was as 29.3%, 9.7%, and 13.3% for Cu, Fe, and S, respectively. Selective recovery of copper by degrading the copper oxalate structure with a low-solubility product (Ksp = 4.43 × 10−10) was performed by conventional leaching in the presence of HCl. The optimum leaching conditions were determined as 5 M of HCl concentration, 318 K of leaching temperature, 120 min of leaching time, 25 ml/g of liquid–solid ratio and 400 rpm of stirring speed. Under these conditions, approximately 77% of copper and 3% of iron were taken into the solution. According to the characterization of the leach residue that was obtained, the oxalate structure was degraded. Moreover, the results of XRD analysis showed that the sulfur (S) and cubanite (CuFe2S3) phases were mostly observed in leaching residues, and this was supported by the SEM-EDX data. Based on the results, it may be stated that selective copper extraction can be obtained from a chalcopyrite concentrate by a two-step leaching method using a conventional hydrometallurgical technique.

By L. C. de Kooker, K. Esmaeili, I. Musonda, M. Ferentinou

A numerical investigation of the effect of pore pressure regime on the safety factor and the critical failure mechanism is presented for fly ash storage facility. Pore pressures’ measurements from standpipe piezometers and pore pressure estimated from seepage analysis are used to compare the factor of safety for a fly ash slope. This was applied for considering static and seismic scenarios. A probabilistic approach was applied to account for the uncertainties resulting from the limited data available and support a qualitative risk assessment evaluation. Slope stability analysis is conducted in two and three dimensions, adopting the limit equilibrium analysis approach, and also a finite element seepage analysis, to assess the stability of the slope. The two-dimensional cross-sections were extruded to three-dimensional models to estimate the factor of safety and associated shear failure. The results from the performed analysis suggest an increase in safety factor values of 5%.

Mar 27, 2024

By J. Drelich

The highly-efficient and economically-feasible technology for bitumen recovery from US oil sands using a water extraction approach was developed at the end of the last century. This water-based bitumen extraction process has been optimized based on observations and analysis of microscopic mechanisms of bitumen release from oil sands and the bitumen transfer to a froth product as well as measurements of interfacial properties of bitumen. The wetting mechanisms that occur in the diluent-assisted water-based processing of US oil sands include bitumen film rupture and recession on sand grains and bitumen transfer to nucleated and injected gas bubbles. These mechanisms are reviewed in this contribution.

Jan 1, 2007

By Jian Deng, Hehua Zhu, Lianyang Zhang

Rockburst is defined as a sudden and violent explosion of rock on the surface of a rock excavation. Rockburst has been regarded as the least understood and most feared hazard problem for underground rock excavations. Traditionally, rockbursts were classified into the strain, pillar, and fault-slip categories. However, rockbursts are also known to occur at stress levels well below the rock yield strength, in mines where the rock is far from brittle, or without the presence of geological discontinuities. A plausible explanation of rockbursts is buckling, which has been identified as one of the main mechanisms for rockbursts. It is observed that rockbursts are often induced by dynamic loadings (pulses) from adjacent blasting. Therefore, the present paper studies the effect of pulse shape and amplitude on pillar rockbursts induced by dynamic loadings from blasting using the method of numerical analysis. The governing equation of a pillar’s motion is set up and the mechanism of pillar rockbursts is investigated through a practical example. The results show that it is not the shape of a pulse but the impact energy to decide the occurrence of pillar rockbursts. If all other parameters remain the same, pillar rockbursts are more likely to occur when the pulse duration is longer. The parametric resonance and the perturbation of dynamic loadings are also found to play an important role in the occurrence of rockbursts. These insights would provide invaluable clues about the mechanism and for better control of pillar rockbursts.

Apr 26, 2022

By H. Maleki

This paper recognizes the 100th year of research accomplishments by the mining industry resulting from close cooperation among mining companies, geotechnical consultants and researchers from the former United States Bureau of Mines in stability assessments and development of improved and productive mine designs. The paper provides an overview of dramatic developments in geotechnical instrumentation, and its applications in the U.S. and around the world for enhancing the understanding of ground response to mining-induced changes in stress, resulting in improvements in ground control technologies.

Jan 1, 2010

By Steven K. Duke, Jay Arabshahi

An economic, real-time probe drill monitoring system was developed for Metropolitan Water District’s Arrowhead Tunnels project to quantitatively evaluate ground conditions ahead of a TBM. This system digitally records hydraulic feed, rotation, and percussion pressures and calculates drill advance rates during drilling. These data are computer synthesized to develop a digital representation of the ground ahead, and the resulting “picture” of the ground is distributed to the project team to assist with tunnel construction decisions (i.e., targeting grout holes, optimizing mine-cycle lengths, and avoiding becoming stuck). The analysis and interpretation procedure has now been calibrated and refined using over 5,000 m (3 miles) of geologic face mapping data.

Jan 1, 2007

By Terry W. Engelhart

"A computer-based approach to online supervisory control and operations management of bulk materials handling terminals". This paper describes an integrated computer facility supporting the functions and responsibilities of shift operations, scheduling, maintenance and management using real-time interactive techniques. The functions and responsibilities as related to coal export terminals are specifically addressed, although these functions would be equally applicable to other terminal configurations and other commodities. A discussion of the resulting benefits are presented: - throughput efficiency - long-term planning and scheduling, using simulation - operations monitoring and protection - demurrage/despatch optimization - preventative maintenance - operational productivity

Jan 1, 1982

By N. Arbiter, C. C. Harris

The economic advantages of large diameter ball mills can be compromised by unexpected capacity limiting conditions. These arise because media rotational flow to ore axial flow ratios, and the number of mill revolutions that ore is subjected to during residence, are both inversely proportional to mill diameter. Because of this, mixing efficiency and grinding kinetics may decrease and become capacity limiting when mill diameters reach a critical range. There are two possible scale-up problems involved in the design and use of mineral processing machinery: • Selecting the size and operating conditions for available larger equipment, to insure that operating results will match those obtained with smaller units; or •Extending the size ranges of equipment beyond existing limits. Previous research at Columbia University into flotation machine hydrodynamics has demonstrated the importance in scale-up of internal flow relationships; these perform a similar role in grinding (Arbiter and Harris, 1980).

Jan 1, 1982