Search Documents

By C. W. Huggins

The primary objective of this Bureau of Mines research was to measure the size distribution of respirable quartz collected at metal mines, nonmetal mines, and processing plants to select the best reference standard for use in quantifying quartz in mine and plant dust samples. The secondary objective was to size all the nonquartz particles collected at the same sites. Particle size measurements were made on 29 samples using a scanning electron microscope in the backscatter mode of operation, interfaced with an image analysis system. The Mine Safety and Health Administration, Denver, CO, provided the 29 samples, which were collected at mines and processing plants in 19 states. The accumulated particle size measurements indicate that NBS 1878, minus 5-f.lm Hin-U-Sil, and minus 5-f.lm Supersil would be preferred over Silver Bond B as reference standards for most quantitative determinations by X-ray diffraction and infrared spectrometry. The respirable dust samples collected at sand plants, however, would be better served by a new reference standard having a quartz particle size distribution of approximately 2.2 um, as none of the four existing reference standards matched closely with them. Commercially available NBS 1878 and minus 5-um Hin-U-Sil CQuid be used as reference standards for 28 of the 29 samples studied in this investigation.

Jan 1, 1986

By Victor R. Spironello

The Bureau of Mines has studied slags associated with ferrous melting, to evaluate substitutes for the auxiliary flux mineral, fluorspar. A waste material recovered from alumina reduction cells, "used potlining," was tested in an 18-in-ID basic-lined cupola and in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF). One potlining fraction, No. 1 cut, is a carbonaceous (graphitic) material and represents the bulk of the entire cell lining. The other fraction, No. 2 cut, is a refractory backup. These materials contain significant quantities of fluorine and other elements fn various compounds. The potlining fractions were blended in ratios believed representative of available materials. Both lump and pelletized forms provided extremely fluid slag. No adverse effects were found on furnace performance, chemistry or strength of the metals produced, or the environment. Fluorine recovery in the slag and fluorine losses to the scrubber water and solids were about the same as when fluorspar was used. There was apparently no lining loss from the cupola, but there was lining attack in the BOF. Since the fluidizing ability of potlining is due in part to sodium and other elements such as aluminum and silicon, less fluorine is needed in the slags when potlining is used.

Jan 1, 1983

By N. E. Hanna

To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain safety tests prescribed by the Federal Bureau of Mines. These tests are described in Schedule 1-G4/ (explosives) and Schedule 26A5/ (blasting devices). An explosive or blasting device that passes the appropriate tests is placed on the active permissible list. As this list is subject to continuous revision, it has been the practice of the Bureau of Mines to publish periodically the names of explosives and blasting devices that have been added to the active list, as well as those that have been transferred to the inactive list; changes in brand names also are reported. The present circular gives all explosives and blasting devices on the active permissible list as of December 31, 1957, and shows all changes, additions, and transfers in that list between December 31, 1951,6/ and December 31, 1957.

Jan 1, 1958

By Yi-Shen Li

This report has been prepared by Lockheed Missiles & Space Company, Inc. (LMSC), under United States Bureau of Mines Contract No. H0220040 dated 21 June 1972 for the design, development, fabrication, and certification of the One-Hour Self-Rescue Breathing Apparatus (PBA). The PBA is a self-contained, oxygen-generating, CO2-removing closed-loop breathing apparatus that provides a minimum of 1 hour of breathable atmosphere during escape from a mine with a contaminated or oxygen-deficient atmosphere. This Cost-Plus-Fixed-Fee (CPFF) contract has been successfully completed in a three-phase program. The Phase I tasks included the design, development, and fabrication of prototype units developed at LMSC in accordance with the requirement of the Code of Federal Regulations (CFR) Title 30, Chapter 1, Subchapter B, Part 11 (Appendix A), and was submitted to the National Institute for Occupational Safety and Health (NIOSH) for joint NIOSH and Bureau of Mines certification testing.

Jan 1, 1974

By Frank H. Reed

This report is one of a series written by members of the Solid Fuels Mission to Germany describing wartime developments in the mining , preparation , and utilization of coal . This mission was organized early in 1945 under the auspices of the Technical Industrial Intelligence Committee , which cooperated with a counterpart British committee . The Solid Fuels Mission operated under the direction of a steering committee headed by Dr. C. J. Potter , Deputy Solid Fuels Administrator . The personnel of the mission consisted of H. F. Yancey, in charge , J. W. Buch, Thomas Fraser , L. L. Newman , and L. D. Schmidt of the Bureau of Mines ; H. H. Lowry , Director of the Coal Research Laboratory , Carnegie Institute of Technology; H. J. Rose , Vice - president and Director of Research , Bituminous Coal Research , Inc .; and F. H. Reed , Chief Chemist , Illinois State Geological Survey . Over 50 reports were written by the members of the Solid Fuels Mission . These , together with microfilms of supporting data obtained in the course of the investigations , are on file at the Bureau of Mines , Washington , D. C. , where they are available for public examination . The Office of the Publication Board in the Department of Commerce is prepared to furnish photolith copies , photostats , or microfilm reproduction of all declassified reports . A Bibliography of Scientific and Industrial Reports is issued weekly by the Department of Commerce , Office of the Publication Board , and is sold by the Superintendent of Documents , Government Printing Office , Washington 25 , D. C. , on a subscription basis . An initial payment of $ 10 will provide for approximately 9 months , and subscribers will be notified when additional remittance is necessary . All subscriptions will begin with volume 1 , No. 1 , unless ordered otherwise . The Bibliography, covers all materials and subjects and gives instructions for obtaining the desired items . The reports of the Solid Fuels Mission relate to the following general subjects : Mining methods in the Ruhr district of Germany , with special reference to mechanical cutting and loading equipment , pneumatic packing , and Diesel mine locomotives ; activities of industrial research laboratories supported by the German coal and coke industry ; coal preparation in western Europe ; low- temperature carbonization processes ; metallurgical coke from

Jun 1, 1948

By George T. Faust

The petrographic microscope plays an important role in the mineral dressing of nonmetallic materials. Petrographers and mineral technologists have evinced an interest in the technique developed, specifically, for mineral-dressing problems. The following dissertation makes the informa¬tion more generally available. ACKNOWLEDGMENTS The authors are indebted to O. C. Ralston, chief engineer, Nonmetals Division, and to Will H. Coghill, supervising engineer of the Southern Experiment Station for a critical reading of the manuscript. They are also indebted to their colleagues for technical information obtained in the course of cooperative work, in particular to J. B. Clemmer for the use of the data on fluorite.

Jan 1, 1940

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag compositions. The present report deals with the SrF2-Y2O3 system for which liquidus and solidus temperatures and solid solubilities were determined. The information is presented as the phase diagram. The phase diagram was constructed from information obtained by ceramogra¬phy, X-ray diffraction, thermal analysis, and electron probe microanalysis of small specimens encapsulated in platinum-20 percent rhodium or molybdenum ampoules. The data indicate a simple eutectic system with limited terminal solid solubilities. The eutectic temperature is 1,457°±5° C, and the eutectic composition is 4±1 mole-pct Y203. Strontium fluoride containing up to 2 wt-pct 0 2 was studied to determine the effects of oxygen contamination. Oxygen levels in excess of 0.2 wt-pct resulted in eutectic formation between SrF2 and SrO. The eutectic composition is between 0.2 and 0.7 wt-pct 02, and the eutectic temperature is 1,447°±5° C. No intermediate oxyfluoride phases were detected.

Jan 1, 1974

By Thomas Varley

During the past few years, since flotation has become the paramount treatment method for most all kinds of ores, the Bureau has gathered the data on consumption of reagents used in the flotation treatment. The first report was issued in 1916. A brief review of such reports snows the progress made in the art of flotation, and each year brings forth the development of new reagent a or combinations of reagents that seem sure to survive, but research and progress spell their defeat, if not by entire elimination, at least subjects them to considerable modification.

Jan 1, 1928

By Lowell Stroud

This report is the third in a series presenting equilibrium vapor-liquid data for helium-bearing natural gases. The first two reports contained phase data for the gases processed for helium at the Bureau of Mines Amarillo and Exell, Tex., helium plants. The present report offers similar information for a lower-helium-content (0.75 mole-percent) natural gas to be processed in the Department of the Interior's long-range helium-conservation program. A windowed-cell apparatus was used to obtain 218 samples of equilibrium vapor and liquid phases at 73 experimental conditions ranging in temperature from -100° F to -275° F and in pressure from 100 to 500 psi. From the phase data, the condensation characteristics, helium solubility, and equilibrium-vaporization-coefficient data for helium, nitrogen, and methane were evaluated. The effect of using a. preliminary hydrocarbon trap upon the subsequent vapor-liquid compositions is reported. A brief comment regarding the composition effect of passing the gas through a gasoline-removal unit is also included.

Jan 1, 1963

By E. R. Maize

[he scconG rcport of :his st?rI.org 8cdt with o3servatioi:s of conver- gence of roof an4 floor at t!x*re: ?.cc.-.tioris iri til~ ClVucible mine of kke Cru- cib1.o Fuel Co. Data on sl:'ociacnce ?.rd Lztcrcl mwe:~cnt cf the surface were .:lven for two of these areas, a-12 it was mentioned that ~lr~~ilar data were being obtained on a ?art of Pe:sc:rlvtzr.ia Fii~l?trr.y FE:, ~i!lic;l pcser: over the third area. 'I'hie hichw~ :LEO FasseE over t!lc ITenncoli::. :.line of the Bnckeye Coal Co. 9 milcs to ';he so-lth, cnd at P. l~tcr C'..att: ~.nr?r.,cc?r:cntS *.rere mnd.e to make similar observati on3 there. This y: pr mrnmri:.c n Czto obtnino? at those two locetionn,]

Jan 1, 1941

By R. R. Sayers

Although the attention of those interested in diseases peculiar to mining as teen focused recently on one duct disease - silicosis - other respiratory diseases may cause more suffering and economic loss. The increased incidence of these diseases usually is attributed to exposure to abnormal air conditions underground, such as sudden changes from high to low temperatures, excessive dust, and noxious gases. The principal respiratory diseases to which the mine is subject axe bronchitis, influenza and pneumonia, pulmonary tuberculosis, anthracosilicosis, and. silicosis. Although the mortality statistics in some of the tables included in this paper are old they have been corroborated by later, lees complete data Bronchitis Bronchitis is en inflammation of the bronchial tubes due, among other causes, to the inhalation of irritants such as dusts (organic and inorganic). Occupations that entail exposure to atmospheres polluted, by irritating gases carry with them the risk of bronchitis. According to Collie (1), it cannot be distinguished clinically from bronchitis occurring among the general population, and its association with tae inhalation of dust or gases usually is unrecognized.

Jan 1, 1941

By A. F. Colombo

The western Mesabi range nonmagnetic taconites containing about 34 percent Fe were evaluated by the Bureau of Mines in a 900-pound-per-hour pilot plant employing a selective flocculation-desliming-cationic flotation technique. The flotation step was a reverse flotation process and involved the flotation of the gangue minerals. The objective of the research was to increase the availability of domestic raw materials for the iron and steel industry. The beneficiated ores yielded concentrates containing 62 to 64 percent Fe and less than 5.5 percent Si02 with accompanying iron recoveries that averaged about 75 percent. Comparable flotation results were obtained with either fresh or 80 to 90 percent reclaimed water. Recycled waters having turbidities as high as 5,000 ppm Si02 did not affect the flotation process. Reclaimed waters containing residual calcium contents of less than 10 ppm gave better flotation concentrates than those containing 15 ppm.

Jan 1, 1976

By Nikolaos Polysos, Holger Witthaus

INTRODUCTION The classification system for German coal mining is the result of approximately 100 years of experience in roadway development and longwall mining. It is also based on different research projects covered by national and European research programs. Over the past 30 years, more then 600,000 m of road-ways have been driven and employed for mining activities. To properly describe the German rock mass classification system, therefore, it is useful to take a look at the main geomechanical preferences and common support systems. The decision about the most effective development technique and support system is based on a synthesis of rock mass classification and geomechanical analysis. The properties of surrounding rock, the in situ stress, and the influence of mining activities in several seams at each German mine must be considered for the evaluation of the expected deformation of the roadway. The mine layout, the requirements of ventilation and fire prevention, as well as the need to maintain emergency escape routes for the miners, require that the gate roads remain usable after the passage of the longwall face in most cases. Moreover, the gate roads must be maintained despite the high stresses that are applied during longwall retreat mining. Therefore, gate road design must address a broad spectrum of potential deformation environments. In the past, when gate roads were supported solely with yielding steel arches, lithologic descriptions of the surrounding strata conditions were adequate for the dimensioning of support and the prediction of the roadway deformation. The current conditions of multiple-seam mining at depths of up to 1,700 m require combined support systems, including pattern bolting and backfilled steel arches. Rock bolt support is used for development, after which (typically 50–100 m outby the face) the steel arches are installed and backfilled with building material (concrete) in order to achieve an optimized development rate. The rock mass classification system described below was developed especially for the conditions of German hard-coal mining. It includes the stress distribution caused by multiseam workings (including crossing goaf edges of former longwalls), as well as in situ stresses due to greatdepth and the presence of tectonic faults. It is based on the evaluation of four parameters: • Geotechnical analysis of drill cores • Geotechnical observation of the development face • Geotechnical classification of tectonic structures (faults) • Standard classification derived from geotechnical assessment and evaluation of stress conditions (using numerical modeling for stress calculation) ROCK STRENGTH One of the most important input parameters for describing strata conditions is the strength of the rock. The German classification system is based on a description of lithotypes. This method has been used successfully since the 1950s and is based mainly on the uniaxial compressive strength (UCS) of the material. An evaluation of the rock strength observed in a survey of approximately 82,500 samples of rock core yielded the results shown in Figure 1. The three most common coal measure rock types are mudstone, siltstone, and sandstone. Each shows a specific mean UCS level and a different spread between the minimum and maximum values. Sandstones, in particular, have a wide spectrum of compressive strength, ranging from approximately 40 MPa to greater than 130 MPa, with an average of 85 MPa. The causes of this wide range include different sedimento-logical preconditions, facies, and digenetic processes. [ ]

Jan 5, 2007

By Paul L. Michael

This report presents a discussion of perforance parameters for electronic or active hearing protectors that will meet the needs of underground coal miners. This information is incorporated into a proposed set of specifications that can be used to judge the suitability of a particular electronic hearing protector for the coal mine application. Acoustic and electrical tests were performed on a developmental model of an electronic hearing protector built by the U. S. Bureau of Mines. This model showed only a slight reduction in speech intelligibility which was traced to poorly matched components and in particular to the transducers. Tests of alternative components showed the Knowles BL-1671 microphone to be suitable for this application because of its performance and extremely small size. The Roan-well H-143/AIC earphone was found to have a good frequency response but has the disadvantage of being rather bulky which causes a slight degradation of a low frequency attenuation of the hearing protector. A satisfactory installation of these components in a hearing protector muff was demonstrated and tested. Results of tests of several methods of controlling the sound level under the hearing protector muff showed that a simple diode clipper circuit can be used with only a negligible loss in speech intelligibility for normal-hearing listeners. A commercially available active hearing protector, the British-built ACOS A-9000/2 was examined. This hearing protector provides sound level limiting through a saturating amplifier. Preliminary tests have shown that the performance characteristics of this commercial unit meet many of the proposed specifications so further testing and evaluation should be performed to determine its suitability for use 1n underground coal mines. The recommended test of intelligibility for electronic hearing protectors and other communication systems as used in a coal mine setting is the Modified Rhyme Test (MRT) developed by House et al. in 1965. The suitability and method of administering this test are discussed.

Jan 1, 1976

By Louis A. Panek

Determining the change of stress in rock based on measurements of the deformation of a drill hole is a procedure that is increasing in popularity. A closely related procedure involves the applicat10n of this principle to determine the existing stresses in a rock medium, by cutting free (core drilling) an annulus containing the drill hole. In this Bureau of Mines report, expressions are derived from which one can calculate the stress ellipsoid--the three-dimensional change of stress, or the existing three-dimensional stress field, as the case may be. Study of these equations shows that the stress components in three dimensions can be determined by measurements in only two drill holes, and yields general principles that are useful in planning an efficient program of drilling and measurement. Procedures are given for calculating the least squares estimates of the stress components and their standard errors, and for evaluating or comparing calculated values by means of standard statistical inferences.

Jan 1, 1966

By C. R. Summers, J. N. Murphy

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneurnaric drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115 -dbA s rope drill to approximately 100 dbA.

Jan 1, 1974

The analysis of in-mine grounding systems began with an extensive literature search which is still in progress. About a dozen articles have been found which deal directly with grounding problems on low voltage power systems or mine power systems. These systems have special grounding problems because normal load currents can be nearly as large as many types of fault currents. Information has been collected on the influence of cable spacing) conduit geometry, location of nearby conducting structures, etc., on the magnitude and path of fault current. Many other articles have been found which are less directly related to mine ground system analysis. The in-mine ground system analysis team has also inspected portions of two mine power systems to become familiar with the practices used in grounding. One electrical engineer and several other mine personnel have been interviewed concerning mine power system grounding practice. Already several aspects of the mine grounding system have been marked as requiring special attention.

Jan 1, 1975

By D. Harrington

Educational campaigns conducted by the manufacturers of explosives, the Bureau of Mines, mining companies, and safety organizations have contributed greatly in reducing accidents caused by explosives arid blasting. Despite these campaigns and the dissemination of information, accidents from explosives and blasting continue to be the direct cause of scores of fatalities and hundreds of nonfatal accidents annually, not only in the mineral industry but essentially wherever explosives are used. The experience of many mining companies and other users of explosives has proved that accidents from explosives can be prevented or averted by the proper training of employees in the handling and using of explosives and by the enforcement of definite rules and instructions for their use. Unfortunately, throughout the years numerous false impressions and ideas have grown up and around the use of explosives. Many of these can be traced back to the manner in which the users of explosives were originally taught, if instructed at all; and as with many types of misinformation in nearly all walks of life, those false ideas are decidedly persistent and being so cause much damage. Many if not most of the users of explosives gained their knowledge of explosives and blasting by watching others and more or less "absorbing" the procedures and thrones of the other fellow, who acted unconsciously as teacher or instructor. A study of explosives accidents reveals the results of such "teachings" when the causes of the accidents are determined, and as might be expected the results very often are far from good. One of the most persistently erroneous impressions or ideas is concerned with the burning rate of safety fuse. Many men with

Jan 1, 1944