Search Documents

By J Sargeant, T Levi, J Theiler, B Beamish

Two coal samples (810 Panel and Area 900) collected from Clarence Colliery have been tested under a controlled heating procedure to evaluate the gas evolution trends corresponding to increasing temperature. Gas evolution data are normally used to identify key gas indicators and validate the trigger action response plan settings for the mine as part of the Principal Hazard Management Plan for Spontaneous Combustion. The samples were located some 6 km apart and there is a significant coal-type difference between them. At low temperatures (<100°C), the Graham’s ratio (GR) values for the two samples are almost identical. However, at elevated temperatures, there is a significant difference, with the 810 Panel coal having higher GR values than the Area 900 coal. This is most likely due to a difference in the coal reactivity. The 810 Panel coal does not evolve ethylene until temperatures in excess of 140°C are reached, whereas Area 900 coal evolves ethylene once temperatures in excess of 120°C are reached. The 810 Panel coal also produces significant ethane evolution (200 ppm) at low temperatures (50°C) due to the presence of retained ethane seam gas, which decreases as the temperature increases due to desorption from the coal. Once the coal temperature exceeds 130°C, the ethane evolution increases again due to coal oxidation reactions, reaching levels of 50 ppm. In contrast, the Area 900 coal has no significant low-temperature ethane evolution, and ethane evolution only increases once the coal temperature exceeds 120°C. There are also noticeable differences in the trends of other gases evolved from the coal. These findings have implications for the interpretation of gas monitoring results from the two different areas of the mine. They also illustrate the need for obtaining results from each new area of a mine as it develops so that changing gas evolution trends can be identified in advance of mining.CITATION:Beamish, B, Sargeant, J, Levi, T and Theiler, J, 2015. Gas evolution trends for coal from two different areas at Clarence Colliery, in Proceedings The Australian Mine Ventilation Conference, pp 273–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By L Eriksson, D Penn, J Appelgren

Atlas Copco, a leading supplier of equipment and services to the mining and construction industries, is consistently pursuing its strategy to offer the most productive and economical solutions by continuously offering new innovative products. These are, in most cases, developed and tested in close cooperation with demanding end users before being officially launched on the international market. The demands for higher productivity and improved overall economy have resulted in systems for automation of the drilling cycle and also tools for integrating the drilling equipment to the production control system used by the customer. In terms of improving the blasted material quality, the company has placed emphasis on accuracy in the drilling process and documenting what has been drilled. By applying state of the art technology to the common automation platform, developed for the surface drilling market, major steps in improving overall drilling productivity and blasting performance have been achieved. This paper will give some examples derived from the latest development of solutions for the companyÆs surface drilling products.CITATION:Appelgren, J, Eriksson, E and Penn, D, 2012. Rotary drilling automation increasing operator productivity and drilling quality, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 13-18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By A Purton, C Taylor, E Conroy

The spatial modelling of geometallurgical domains is an important step in the characterisation of an ore deposit allowing for the quantification of various rock types, their differing rock properties and the overall value of a project. The traditional approach to modelling such features is through the use of deterministic models, where a single estimate of the extents and structure of the ore deposit is mapped out by geologists based on available data and their interpretation of the geological processes. Any uncertainty in the layout of different domains is not accounted for and heterogeneities of chemical and physical properties of the orebody are likely underestimated. Spatial machine learning techniques can be used to derive geometallurgical categories, or classes, from multiscale, multiresolution and high dimensional measured rock properties. Subsequently, geostatistical simulations of these classes can be applied to obtain multiple equiprobable realisations that define the layout of the geometallurgical classes at unknown locations between boreholes, or domains. In-turn these realisations can be used quantify the uncertainties in the location of boundaries between different domains. The development of a workflow for defining geometallurgical domains and later geostatistically simulating them across the Orebody H; a complex stratabound Bedded Iron Ore deposit located in Western Australia’s Pilbara region is demonstrated. This could be used to identify zones of high uncertainty where collection of additional data might help mitigate or minimise risks and in turn improve forecast production performances.

Mar 22, 2022

By F C. D Michelin

As mines get deeper, the critical underground temperature limits will be exceeded, and an increasing number of mines will need to implement, expand or modify cooling systems. Surface cooling plants have many advantages over underground cooling such as efficient heat rejection, and lower relative capital cost; however the delivery of cooling through long underground distances can result in lost refrigeration capacity before the chilled air reaches the areas it is needed most. Refrigeration plants are therefore often overdesigned in size and capacity to compensate for underground losses.More mines are now utilising real-time monitoring and automated control of ventilation airflow and fan systems to ensure the conditions underground are safe and productive, and power consumption is efficiently managed. There may be significant opportunities to extend ventilation monitoring and control into the refrigeration delivery and control system.Energy reduction is an effective way to reduce costs and CO2 emissions, which is an increasingly important part of corporate governance. More efficient refrigeration control is a further step toward reducing energy consumption. This paper looks at an added step in how real-time monitoring can assist in controlling the output and chilled air delivery of a cooling plant. The requirements, implementation, benefits and challenges will be discussed.

Oct 12, 2022

By D Connelly

Magnetite ores can be used to produce very high-grade concentrates that are suitable feed for the direct reduction process route but the high sulfur content of some concentrates can cause substantial environmental issues. Processing of high sulfur magnetite ore is therefore increasingly problematic for the industry. Generally, the industry demands a concentrate with <0.05 per cent sulfur and <2 per cent silica. This paper reports the outcomes of a study to produce a concentrate with the requisite low sulfur content from a sulfur-rich magnetite ore. The main findings may be summarised as follows: if the sulfur is present in magnetite as nonmagnetic pyrrhotite or pyrite, it can be beneficiated using magnetic separation and hence, monoclinic pyrrhotite is magnetic and is magnetically recovered with magnetite leading to a concentrate that is too high in sulfur. X-ray diffraction and QEMSCAN analyses revealed that the magnetite concentrate was liberated at P80 30 microns and was associated with maghemite, pyrrhotite (magnetic), carbonates and hematite with very low amounts of chalcopyrite, sphalerite and arsenopyrite. Sulfur removal using flotation was the first stage of investigation and this required flash flotation in the grinding stage followed by column flotation of the initial concentrate to generate the final concentrate. At the same time, it was observed that oxidation of the pyrrhotite had a negative effect on its flotation requiring copper sulfate to activate it. Bioleaching and concentrate leaching were also considered and achieved over 90 per cent sulfur removal but were deemed unsuitable owing to the production of highly reactive wastes and high CAPEX. Reference is made to a number of operating magnetite producers and how they manage the sulfur in feed.

Sep 18, 2023

By M Behrens

The Melbourne Main Sewer Replacement (MMSR) is a major urban infrastructure project involving approximately 2.3 km of tunnelling and construction works. The works extend from Docklands Precinct, on the southwest edge of the city, southwards to connect with the Hobsons Bay Main Sewer in Port Melbourne. The tunnel boring machine (TBM) tunnelled section of the works terminates at the Yarra River where the delta geology and alignment requirements precluded the use of underground tunnelling methods. The 132 m long river crossing works involve a cut-and-cover excavation within a staged fl ooded cofferdam construction to construct an immersed tube tunnel as an extension of the TBM works.This paper reports on the development of the staged construction method and highlights the geotechnical and structural design aspects involved in building a new sewer in the Yarra River to close the gap between the new TBM driven and pipe-jacked tunnels.

Mar 8, 2011

By O Arafat, K M. Bartholomew

A voracious consumer of energy and grinding media, the modern ball milling circuit has a huge direct cost impact on a mineral processing operation. Through optimisation, grinding also has the potential to unlock great improvements in recovery and throughput, but how can the complex interactions between mills, classifiers, tonnage, ore-type and downstream recovery be measured, understood and managed in a systematic manner?Functional performance analysis provides the tools and insights needed to measure, understand and improve the two key process efficiencies in ball milling circuits: classification system efficiency (CSE) and mill grinding efficiency.CSE measures the composite performance of the classification system as a whole. In short, the purpose of the classification system is to ensure that grinding mill energy is used to grind coarse particles while minimising overgrinding. CSE is simple to measure in the plant and it provides immediate feedback to the plant metallurgist, mill superintendent and management about the performance of the classification system and the amount of wasted energy in the grinding plant.Mill grinding efficiency measures the capacity of the grinding mill to convert feed-sized material into product-sized material on a tonnes per kilowatt hour basis. It is normalised based upon the ore resistance to breakage, so it provides feedback about the ‘health’ of the milling process under varying operating conditions and ore types. Mill grinding efficiency is measured at the same time as CSE through circuit sampling.Functional performance analysis combines CSE and mill grinding efficiency to provide a measureable, manageable optimisation objective. It also provides a link to tonnage, ore type and recovery. As a result, systematic optimisation of a grinding circuit is a measureable and manageable process to meet business objectives.CITATION:Bartholomew, K M, McIvor, R E and Arafat, O, 2014. Functional performance of ball milling circuits – a plant metallurgist’s tool for process characterisation and optimisation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 227–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By K J. Riihioja, E Nozawa

SmartTag is a radio frequency identification (RFID) based technology designed to allow tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles and finally into the concentrator. This paper presents current developments and the future direction of the SmartTagÖ ore tracking system, as well as presenting some case studies. Successful applications of the SmartTag system have encouraged development to allow the system to be used in a wider variety of plants, in particular plants with finer crushing and screening stages. This presented Metso with a number of technological challenges, including RFID tag and antenna design. By reducing the traditional RFID tag diameter from 60 mm to 20 mm the RFID tags can now successfully pass through a secondary crusher. The new smaller RFID tags (referred to as mini RFID tags) have been used in some Process Integration and Optimisation projects with very promising results. The results indicate that the miniature RFID tags have a higher survivability to blasting and through secondary crushing stages. Extending ore tracking further through the process allows more reliable linking of spatial data with time based process performance. Metso is looking at developing even smaller micro RFID tags, and is also investigating other applications for the SmartTag system, including ore tracking from the original source to the final destination (ie from the mine, through the plant and ports to the customer).

Sep 26, 2011

By F P. van der Meer, E Lessing, E Matthies

High pressure grinding rolls (HPGR) technology is growing to be a common comminution tool in iron ore processing. The technology finds a wide acceptance and presents specific benefits in coarse ore grinding and closed-circuit grinding in preparation of ball mill feed, right down to the other end of the particle size spectrum for iron ore pellet feed preparation.A growing number of minerals processing plants are facing higher operating costs and difficulties due to a scarcity of process water, which in some cases is a result of more stringent environmental constraints. In addition, many new iron ore deposits are located in more arid regions of the world. These challenges have led to operators taking a new look at dry processing of iron ores.The use of dry crushing and classification technology in cement production from blast furnace slag, clinker material or limestone feed stocks indicates that the technology may be applied in minerals processing. In addition, dry processing provides the possibility of generating a final product from finely disseminated and inter-grown ores at sizes near or well below 100 &#181;m, as may be required for beneficiation techniques such as in fine magnetic separation, flotation or magnetic flocculation.Dry grinding by HPGR has a number of specific features, challenges and opportunities, including balancing power input, moisture content requirements and classification efficiency in the process design. HPGR parameters and the latest HPGR design and sizing capabilities indicate considerable potential benefits from this dry processing technology.This paper highlights some of the specific issues that play a role in dry HPGR application, with respect to energy and materials balances. Examples of dry HPGR practices and process studies in iron ore mineral processing are discussed.CITATION:van der Meer, F P, Lessing, E and Matthies, E, 2015. Iron ore final grinding by high pressure grinding rolls and air classification, in Proceedings Iron Ore 2015, pp 197–204 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By R Price

"Technology has the potential to revolutionise industries, work functions or businesses. One such technology in the mining industry is the deployment of automation in a modern autonomous haulage system (AHS). This paper examines a theoretical application of an AHS in a medium scale mine site. The cost-benefit commercial argument is particularly compelling, and the paper outlines metrics and future issues for consideration.Citation:Price, R, 2016. Autonomous Haulage Systems - the Business Case, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 11–17 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By R Jaine, D Strang, M Fowler

"This paper presents a case study demonstrating active geotechnical pit slope management at the now completed Carina Iron Ore Project operated by Mineral Resources Ltd (MRL). The site is located 105 km north-east of Southern Cross, Western Australia. The paper is primarily focused on the slope stability failure modes and the remedial measures employed to maintain mining.Between a quarter and a third of the excavated slopes were impacted by some form of instability that was beyond expectations of the intended slope design criteria and common practice. Ongoing mining was supported by intensive geotechnical pit slope management including close cooperation between geotechnical, mine planning and operations staff to achieve timely and practical mining solutions.Mining encountered varied slope failure mechanisms which required a combination of remedial solutions comprising: horizontal depressurisation holes, deferral of excavation, unloading, buttressing and catch berms.The root cause of the challenging slope performance was a mismatch between the predicted and encountered geotechnical model, resulting from a failure to recognise the critical mechanisms that control slope stability.Despite the extensive zones of instabilities at completion of mining, full ore recovery was achieved without major delays and in a controlled and safe manner.Citation:Fowler, M, Strang, D and Jaine, R, 2016. Adapting to Geotechnical Change - a Case Study of the Carina Open Pit Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 150–161 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By D Phillpotts, S M. Mantsho, P Strobos

A challenge on many industrial flotation circuits is controlling concentrate mineral grades using measurements that are provided infrequently. The mineral grades in concentrate streams are a critical performance indicator in any industrial flotation circuit. Failure to achieve concentrate mineral grade targets has significant financial consequences on a flotation operation. A violation of a gangue mineral grade limits by the concentrator may also result in significant penalties. Online grade analysers which can provide reliable real-time grade measurements are essential for effective grade optimisation. The Blue Cube MQi analyser (by Blue Cube Systems) has recently come to prominence for its ability to rapidly determine mineral concentrate grades online and in-stream. This has provided excellent insight into the actual process dynamics in the flotation circuit, and hence enabled real-time control and optimisation of concentrate mineral grades. MintekÆs Measurement and Control division, specialising in advanced control solutions for mineral and metallurgical industries, has had the opportunity to link the FloatStar Grade-Recovery Optimiser to the measurements provided by the Blue Cube system at a nickel concentrator plant. The project initially focused on stabilising the final concentrate grade without directly accounting for nickel recovery. The site later procured additional Blue Cube MQi analysers, resulting in the expansion of the FloatStar Grade-Recovery Optimiser to incorporate recovery component in the performance. This site already had the FloatStar Grade-Recovery Optimiser for several years, but the original grade measurement device was unreliable and ultimately failed. The system was reactivated once the Blue Cube system was installed, replacing the old analyser.CITATION:Mantsho, S M, Phillpotts, D and Strobos, P, 2012. The implementation of FloatStar grade-recovery optimisation control solutions using Blue Cube online grade analysers on industrial flotation circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 363-368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By R Zhang, J Xu, X Lv, C Bai, S Zhang

This paper studies the grinding behaviour of vanadium-titanium magnetite concentrate in a ball mill. The grinding kinetics, surface morphology, lattice distortion, wettability and moisture capacity were analysed. Grinding kinetics equation was established based on population balances model with the size distribution data from a laser diffraction technique. The SEM photos of the ground concentrate showed that the surface gets rough with increasing grind time. Agglomeration of fine particles was enhanced when the grinding time reached 30 minutes. X-ray diffraction results showed that a loss in crystalline occurred with increasing the grinding time. The peaks of the X-ray diffraction patterns are significantly broadened with increasing grinding time. Wettability, characterised by contact angle between the material and water, improved due to the fact that the surface roughness increased with increasing grinding time. Moisture capacity of concentrate ascends abruptly in the first three minutes and then changed slowly with increasing grinding time. The water transfer coefficient in the particles increased rapidly in the first six minutes and then decreased quickly until grinding time reached 12 minutes.CITATION:Zhang, R, Lv, X, Bai, C, Xu, J and Zhang, S, 2013. Wet grinding of ?vanadium-titanium magnetite concentrate in a ball mill, in Proceedings Iron Ore 2013 , pp 511-518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By A Cranley, A Giblett, S Thacker

The Newmont Tanami Operations are located in the Northern Territory, approximately 550 km north-west of Alice Springs. The Granites process plant commenced operations in 1986 as a 300?000 t/a ball mill / carbon-in-leach (CIL) plant and has undergone numerous expansions between that time and the current day, with project-to-date gold production exceeding 6.5 Moz. Annual plant throughput has exceeded 2.8 Mt/a while processing a blend of open pit material and ore from the Callie Deeps underground mine, with annual gold production exceeding 400 koz. In 2013 the operation processed 1.8 Mt of underground ore for the production of 323 koz of gold.This paper reviews the operation and expansion of The Granites process plant since the mid to late 1980s with particular focus on the gravity gold recovery circuit. The Tanami ores contain significant levels of free gold, and gravity recovery has long been an integral component of the metal recovery process at the Granites plant. The results of ten years of gravity circuit performance analysis and optimisation are presented.CITATION:Giblett, A, Cranley, A and Thacker, S, 2014. Three decades of gold production at the Newmont Tanami operations, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 209–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By J Li, A McFarlane, J Yu, L L. Kuhar, R Meakin, N Chapman

"Column leach tests are used frequently to predict recoveries and reagent consumption for nickel laterite heap leaches. These column leaches often run for more than 100 days and therefore require long-term monitoring and data analysis to achieve the desired information. To minimise the cost and time required to obtain relevant information for nickel laterite heap leaching, we have developed a small-scale hydrogeometallurgical laboratory test to serve as a proxy to column, and by inference, heap leaching. In excess of 50 leach tests were conducted using four different small-scale proxy and column leach tests to compare predicted nickel recoveries, acid consumption and leach kinetics and to determine whether insight into potential scale-up effects can be obtained. The most promising proxy test was identified and we achieved a statistically significant recovery and acid consumption correlations between this test and the column leach tests. The accuracy of the small-scale tests was confirmed by column tests run on new laterite ores. This geometallurgical proxy could be of use for the population of block models and process selection during the mine planning phase or for optimisation and control during processing.CITATION:Li, J, Kuhar, L L, Meakin, R, Chapman, N, McFarlane, A and Yu, J, 2016. A Geometallurgical Proxy for Nickel Laterite Heap Leaching, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 335–340 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By B Murphy, J L. Heath

Installation of flotation equipment is a lengthy and intricate process involving conceptual design, detailed design and layout, equipment installation, equipment commissioning and handover prior to the plant commencing operation. During these steps, mistakes are often made that lead to increased costs and/or schedule delays in bringing the new equipment online.This paper presents a series of recommendations for the installation and commissioning of flotation equipment to minimise mistakes and ensure that plant production commences efficiently with a minimum of resources. The advice herein is based on lessons learnt from recent flotation equipment commissioning. It is intended as resource material for flotation plant designers, construction contractors, metallurgists and operators, and is applicable to both new and existing plants.CITATION:Heath, J L, Murphy, B and Bourke, P, 2014. Effectively installing and commissioning flotation equipment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 399–404 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By R Shaw, T T. Neidel, C Adams

Sampling equipment manufacturers endeavour to ensure that the mechanical equipment installed in sampling systems are designed and manufactured to adhere to the requirements of the International Organization for Standardization (ISO) or other standards relevant to the application. The mechanical parameters necessary to achieve these standards can be well controlled and requirements such as constant speed can be met through good mechanical design and engineering. However, when the equipment is installed and put into operation, the ISO compliance of the system is out of the hands of the equipment manufacturer and handed to the operator, who may be a generalist control system integrator.Making a sampling system perform according to standards, and being able to monitor and report on compliance require that the sampling system knowledge and the control integration is combined and applied in an integrated approach. Using a dedicated library of control routines developed for sampling can change a system from having compliant equipment to being a compliant system. The library has to include monitoring of relevant parameters and control and reporting on sampling parameters.CITATION:Neidel, T T, Adams, C and Shaw, R, 2014. Control and monitoring of International Organization for Standardization compliance for industrial sampling systems, in Proceedings Sampling 2014 , pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By X Xia2, X Wang, G Liang, T Song, F Ma

Inertia cone crushers have found applications mostly in steel slag crushing operations in China. Compared with conventional eccentric cone crushers, the crusher has an obvious advantage in reducing product size. In addition, they are mostly used in two-stage open circuit crushing flow sheet, which simplifies the crushing process. However, inertia cone crushers are not widely used in the mineral processing industry due to their low crushing capacity. In this paper, the throughput performance of the inertia cone crusher was investigated in a laboratory-scale inertia cone crusher and relationships between operational parameters were identified. Iron ore was crushed using orthogonal experimental method under different machine parameters and operational conditions. The crusher throughput and product size distributions were determined. The effects of parameters such as eccentric speed, discharge gap, eccentric mass and eccentric distance on product mass flow and product size were investigated. The results of this study can help reduce the feed size of the mill in order to reduce total energy consumption of comminution.

Aug 24, 2022

By E Wargem

The optimum mining of an orebody in an underground mining operation is fundamental to the mine’s ability to operate both sustainably and efficiently. The effective mining of an open stope or a cave is largely reliant on the recovery of the initial void created by conventional drilling and blasting. These initial voids are known by various names such as a Longhole Rise, Slot or Winze and can be mined either as a downhole or as an uphole. Regardless of the underground mining method, the process of the design and implementation of this initial void is largely uniform across many operations with various patterns of slot or winze designs used across these different operations. Diligent design, implementation and review strategies in drilling and blasting of these will facilitate cost-effective mining with minimal disruption to mine schedules and production targets. When an operation struggles in opening the initial void in underground mine blasting, it has a negative impact on productivity, mineral recovery, and the overall economics of mining. Near field blast vibration monitoring is a vital tool to use in analysing slot blasts and will provide additional feedback into the reconciliation part of the drill and blast process. It is one that is often overlooked in the mining industry in many operations due to many factors such as lack of skilled personnel, or a lack of required resources. The data obtained from near field blast vibration monitoring can be used to provide additional feedback into blast reviews and help in any drill and blast optimisation projects. This paper highlights key aspects of underground drill and blast reviews and the use of near field blast vibration monitoring for post blast analysis and shares learnings from various projects that the authors have been involved in within Australia and abroad.

Mar 29, 2023

By M Franklin, C Puglisi, S Fitch

Implementation of a well planned and executed Management Operating System (MOS) can result in widespread improvements to operational performance but its success relies heavily on the investment by and engagement of the larger workforce with the project. Over the seven month period of the Telfer MOS project, significant improvements were achieved; a 20% increase in monthly hoisted tonnes from the open stope and sublevel cave operations and a 45% increase in square metres of ore extracted from the narrow vein operation. The Telfer MOS was undertaken with the intention that the project wasn’t solely about producing new tools, it hinged on the investment and behaviours of the personnel affected by these tools and alterations. To ensure that the project ran smoothly, the Byrnecut senior leadership team and their operators were heavily involved in the project’s development. In the initial stage, Telfer’s MOS project determined that the quality and accuracy of the information received in the form of radio calls to mine control and completed operator plods was questionable. This required an overhaul of the data collection and verification process in the form of altered operator plods, which was then cross referenced with the operator’s radio calls to mine control. Once the data collection and verification process was implemented, the Telfer team was then able to produce several tools with the aim of providing visibility to the data being captured and its implications. These tools allowed the mine foremen to determine whether equipment was being under-utilised and where they should focus their production efforts to meet monthly targets. Whilst the initial underground project is now complete, the implementation of MOS across the entire site is ongoing with significant operating improvements occurring.

Mar 15, 2021