Search Documents

By M. C. Chang, J. Dasher

The Crucible mine in Pennsylvania, operating on Pittsburgh seam coal, is rated at 5000 tpd. The washing plant, built in 1943, is rated at about 400 tph, using hydroseparator boxes to wash the coarse coal (4 x 5/16 in.) and hydrotator units for the fine coal (5/16 x 0). It is generally acknowledged that gravity concentration equipment cannot be used efficiently to bene-ficiate coal finer than about 65 mesh. Before the present flotation circuit was installed, Crucible recovered its fine coal slurry, predominantly —24 mesh material, by passing it through a battery of five 14-in. and one hundred and ten 3-in. Hey1 & Patterson cyclones in parallel with a 75-ft Dorr thickener. About two thirds went to the cyclones and one third to the thickener. Underflows from cyclones and thickener were filtered, respectively, in one 12-disk Eimco and two 4-disk Oliver filters fitted with stainless steel cloth. The resulting cakes were added to the coarse metallurgical coal. The filtrates, overflow from the 3-in. cyclones, and thickener overflow were recycled to the coarse coal plant. The three major problems encountered in this system became acute when the mine switched from track-mounted machinery to the more economical off-track equipment. The quality and uniformity of product declined, too much slime accumulated in the circuit, and waste pond disposal became highly impracticable. Lowering of Quality and Uniformity: Since the filter cake was not beneficiated in any way, addition of this material, which contained about 18 pct ash. would certainly lower the quality of metallurgical coal. Difficulties of handling the high-ash, high-moisture cake were compounded by the lack of adequate blending facilities at the mine, making it impossible to maintain uniform feed for the coke ovens. For a two-month test period, to verify the source of trouble, all filter cake was excluded from the metallurgical coal. The excluded filter cake was stocked in the yard. Slime Buildup: The moisture retained in the coarse coal products and the filter cake provided daily the only means of slime bleed from the circuit. As this bleed was not enough to offset the incoming fines in the raw coal feed, there was excessive buildup of slimes. To operate at all, it was necessary to purge the system each weekend by pumping all the solids from the thickener to a waste pond. The slimes built up during the week progressively increased the apparent viscosity and density of the circulating plant water, so that hydroseparators and hydrotator units had to be constantly adjusted. Uniformity, yield, and quality of the metallurgical coal suffered in consequence, and the filter cake ash and moisture contents increased from Monday to Friday. Limited Waste Disposal: Location of the plant does not permit unlimited waste pond area. Maintenance of a waste pond for the purpose of emptying the thickener during weekends became a costly burden that could not be tolerated. HOW THE PROBLEMS WERE SOLVED The flowsheet (Fig. 1) chosen to overcome these difficulties is considered the one most economical to install and operate. In a preliminary change made before the flotation circuit was installed, the cyclones and thickener were first operated in series, the overflow from the 3-in. cyclones, after flocculation, being discharged into the thickener and the thick-

Jan 1, 1960

By Yoon T. Auck, Milton E. Wadsworth

Column leach studies of two low grade prophyry copper ores were made with variables of size, flow rate, pH, drainage rate and tempature. Evidence is presented to show that, in some types of ores, sulfide minerals block leaching channels and regulate the rate of dissolution of gangue constituents. Basic iron sulfates, dissolved by introducing acid, provide oxidizing agent in the form of ferric ion in the absence of oxygen. Ferric ion then acts to release copper from the ore. Oxygen up-take was found to increase with the lowering of the pH and to follow parabolic kinetics attributable to the precipitation of basic iron salts within the pore channels. Slow drainage of residual gravitational water can seriously retard oxygen up-take during oxidation for particles in the coarse sand range. A model is presented for dump leaching in which a reaction zone connected by channels to the surface of the ore particle moves topo-chemically during the course of the reaction.

Jan 1, 1973

By J. H. Hollomon, L. D. Jaffe

The hardenability concept has become widely used during the last few years for the choice and substitution of steels. Before the work of Grossmann,1 the systems for predicting hardenability from chemical composition could be used only over a narrow range of composition. Grossmann introduced a comprehensive system, which has been effective in calculating the hardenability of most types of moderate or low-alloy steels. However, occasions often arise that require the calculation of the hardenability of high-alloy steels from their chemical compositions. Experimental determinations of the hardenabilities of such steels indicate that the Grossmann system predicts much greater hardenabilities than are realized. The fact that cases do arise in which the Grossmann method does not apply indicates that the fundamental hypothesis of the system may not be generally applicable. It seems advisable to re-examine not only Grossmann's system but also the concept of hardenability itself. Hardenability If steel parts are to possess a martensitic structure after quenching, they must first be austenitized and then cooled through the pearlite and bainite transformation ranges sufficiently rapidly to avoid the formation of pearlite, bainite, and pro-eutectoid products.* If, on cooling, these transformations are avoided, the resulting structure can consist only of martensite (and retained austenite). The hardenability of a steel is measured in terms of the severity of the cooling conditions necessary to avoid the pearlite and bainite transformations. The less rapid is the cooling necessary to prevent the formation of bainite and pearlite, the higher is the hardenability. The pearlite and bainite reactions appear to be differently affected by the alloying elements. Not only is this indicated by the published isothermal transformation data, but recent work by Zener2 affords a rational interpretation of the differing effects of the alloying elements. Manganese,3 for example, appears to decrease the rates of the pearlite and bainite transformations by equal percentages, while molybdenum45 is approximately 10,000 times more effective in retarding the pearlite than in retarding the bainite transformation, on the basis of isothermal measurements. In some steels, the formation of bainite restricts the formation of martensite while

Jan 1, 1947

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansenl and Haughton,² the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 157.3²C O.l°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys, 4,6 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157. ²°C ± O.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4°C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. Thermal Analysis Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high- flash point was used. A platinum-platinum rhodium thermocouple of fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermocouple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.²°Cl and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it scems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16 in. thick, sufficed to give a cooling rate of from I° to ²°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948

By Alexander Squire

One of the principal factors that have contributed to the hesitancy of design engineers to use metal-powder parts is the difficulty experienced in the determination of the mechanical properties of compacted components. Because standard test methods cannot usually be applied in the inspection of such parts, and because adequate special test methods have not been developed, it has been considered desirable to investigate the methods that are applicable. These may then be included in specifications for metal-powder materials and components in order that the design engineer may be assured that the subject parts possess the desired mechanical properties for satisfactory performance. It is known that direct relationships exist between usually nonmeasurable properties as tensile strength and elongation and shear strength and the angle through which compacts may be plastically deformed before fracturing. These correlations are valuable in the inspection of specific parts, but it is necessary to set up standards before they may be satisfactorily employed. Apart from the use of correlations, the number and character of the inspection methods that are applicable to almost all powder parts is limited to three—chemical analysis, density, and hardness. The last of these may or may not be a pertinent characteristic, since the indentation hardness of many powdeied-metal materials is so low as to have little significance. It is, however, occasionally desirable to use hardness measurements as an indication of the uniformity of the structure of pieces of a given type. Chemical analysis reveals very little about the physical properties of metal-powder compacts, since the unpressed powder is usually of a composition almost identical with that of the finished pieces. Density determinations are simple to perform and have the advantage of being nondestructive in character. If the dimensions of a machine part are known (and usually they are), the average density may be determined by weighing a given number of pieces and dividing by the calculated volume of the parts. More accurate measurements may be made by the water-displacement method. It is recognized that mechanical properties of metal-powder materials are related to their density, but usually these relations are determined for only one type of powder, processed under a given set of conditions. Comparisons of the pioperties of compacts formed from different types of powders are made on the basis of compacting pressures instead of density, and for this reason the results obtained by using powders of different types appear widely variant.

Jan 1, 1947

By Ira Joralemon

THE Ajo copper district is in the heart of the Arizona desert, near the western boundary of Pima county. Gila Bend, the nearest railroad point, is 43 miles north of the camp, and the little Mexican border town of Sonoita is 30 miles south. Between Gila Bend and Sonoita, Ajo is the only settlement save for one or two small cattle ranches and the uncertain villages of nomadic Papago families. The Little Ajo mountains rise a few hundred feet above wide desert valleys, beyond which are lava mesas. The camp itself lies at an elevation of about 1,900 ft. above sea level, in a little basin on the east side of the range, separated from the open desert by low hills. In the center of the basin the brilliantly iron and copper stained rocks of Copper mountain rise 150 ft. above -the village. Many varieties of cactus and low desert bushes cover the hills, while in the large valleys there are clusters of mesquite paloverde, and ironwood trees which furnish limited amounts of fairly good fuel. A scanty supply of water is obtained from wells in the desert and from prospect pits in the camp. The nearest abundant source of water is the Gila river, 50 miles north of Ajo. (See Fig. 1.) HISTORY OF THE AJO DISTRICT The Ajo, next to Santa Rita, New Mexico, is claimed to have been the first copper district in the Southwest worked by Americans. In the '60's or even earlier high-grade native copper and cuprite Ore was mined from shallow surface workings and hauled by bull team 400 miles across the desert to San Diego. From there it was carried in sailing ships to Swansea, Wales. Later, the ore was hauled to Yuma, floated down the Colorado river to the Gulf Of California, and shipped to Swansea. Bat-infested old workings and the massive axles of the bull carts are shown to prove the truth of the stories.

Jan 8, 1914

By L. J. Howell, R. C. Sommer, H. H. Kellogg

WORK described herein was undertaken with the aim of determining some of the physical-chemical properties of electrolytes suitable for the electrodeposition of pure zirconium metal. In this paper the phase diagram, vapor pressure, and activities in the melt are considered. In a companion paper,' the electrolytic conductivity of some of these melts is reported. The melts studied were mixtures of NaCl and/or KC1 with ZrC1,. Chloride melts were chosen for study because 1) if the electrolyte is to be useful for industrial electrodeposition of zirconium, the chlorides will be preferred to the relatively costly bromides and iodides; 2) fluoride melts were being studied in another laboratory (Horizons Inc., Cleveland); and 3) melts containing oxygen, in any form, are unsuitable for preparation of pure zirconium, because of the great affinity of this metal for oxygen. Unlike electrodeposition from aqueous solution, the fundamental behavior of fused-salt electrolysis is poorly understood. In most cases, such basic electrochemical information as the phase diagram of the melt system, activities in the melt, conductivity, the nature of the current-carrying ions, the equilibrium electrode potentials, and the overvoltage behavior of the electrodes is unknown to the researcher who would develop a new electrodeposition process employing a fused salt. This research project was designed to supply information about some of these basic physical-chemical properties so that an intelligent choice of electrolyte for electrodeposition studies could be made. Experimental The experimental difficulties-encountered in this work result from the properties of zirconium metal and ZrC1,. ZrC1, is a solid which sublimes at 334°C. It is rapidly hydrolyzed by moist air to HC1, ZrOCl,, and ZrO,. Unusual precautions were exercised in this work to prevent hydrolysis of ZrC1, and rigidly to exclude oxygen, nitrogen, hydrogen, and carbon from the melts under study. These elements are known to react with and contaminate zirconium metal. All melts were studied in vacuum systems, i.e., in the presence of ZrC1, vapor only. Transfer of ZrC1, to or from the melts was accomplished entirely by vacuum sublimation. In this way, neither the melts nor the ingredients thereof were permitted to

Jan 1, 1958

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The Blast Furnace Studies Section, Metallurgieal Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1940

By Oliver C. Ralston

A definite field of usefulness has developed for the brine-leaching processes of removing lead from ores and other products, so this paper reviews the developments, both in practice and in research, that have taken place since the publication of two earlier papers on this subject.' Several commercial plants are now in operation and a number of semi-commercial test plants have been operated in an effort to determine the limitations of brine leaching and to compare the results with other forms of treatment. Briefly, the brine leaching of lead depends on the fact that lead chloride and lead sulfate are soluble in saturated sodium-chloride solutions. In dilute brines, the solubility of the lead salt is less than in pure water; but in the strong brines, the solubility is greater than in pure water due, supposedly, to the formation of a double sodium-lead chloride. This is seen in Fig. 1, which shows the results of M. Demassieux2 on the solubility of lead chloride in sodium-chloride solutions of different concentrations and at three temperatures. The curves are not those given by Demassieux but are calculated from his results in order to convert them to units common in metallurgical work. The right-hand branch of each curve shows that if the solution is kept in contact with solid sodium chloride the lead chloride can be almost entirely displaced from solution, but that brines which are saturated with sodium chloride, but are not in contact with the solid salt, have a very high solubility for lead chloride. The diagram gives the analysis of the solution in grams of lead per liter, although the substance actually in solution is lead chloride. At 100" C. as much as 100 gm. of lead per liter can be obtained; but at lower tem-

Jan 1, 1924

By L. D. Jaffe, J. H. Hollomon

The hardenability concept has become widely used during the last few years for the choice and substitution of steels. Before the work of Grossmann,1 the systems for predicting hardenability from chemical composition could be used only over a narrow range of composition. Grossmann introduced a comprehensive system, which has been effective in calculating the hardenability of most types of moderate or low-alloy steels. However, occasions often arise that require the calculation of the hardenability of high-alloy steels from their chemical compositions. Experimental determinations of the hardenabilities of such steels indicate that the Grossmann system predicts much greater hardenabilities than are realized. The fact that cases do arise in which the Grossmann method does not apply indicates that the fundamental hypothesis of the system may not be generally applicable. It seems advisable to re-examine not only Grossmann's system but also the concept of hardenability itself. Hardenability If steel parts are to possess a martensitic structure after quenching, they must first be austenitized and then cooled through the pearlite and bainite transformation ranges sufficiently rapidly to avoid the formation of pearlite, bainite, and pro-eutectoid products.* If, on cooling, these transformations are avoided, the resulting structure can consist only of martensite (and retained austenite). The hardenability of a steel is measured in terms of the severity of the cooling conditions necessary to avoid the pearlite and bainite transformations. The less rapid is the cooling necessary to prevent the formation of bainite and pearlite, the higher is the hardenability. The pearlite and bainite reactions appear to be differently affected by the alloying elements. Not only is this indicated by the published isothermal transformation data, but recent work by Zener2 affords a rational interpretation of the differing effects of the alloying elements. Manganese,3 for example, appears to decrease the rates of the pearlite and bainite transformations by equal percentages, while molybdenum45 is approximately 10,000 times more effective in retarding the pearlite than in retarding the bainite transformation, on the basis of isothermal measurements. In some steels, the formation of bainite restricts the formation of martensite while

Jan 1, 1947

By Walter L. Maxson, Fred C. Bond

THIS paper is a continuation of two earlier papers, l, 2 and presents new data on the grindability of various ores and other materials-the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRINDABILITY OF VARIOUS ORES This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at x6-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1 ½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1938

Teamwork: The famous first sentence of an essay en- titled Aphorisms, by Hippocrates, is as follows: "Life is short, the Art long, opportunity fleeting, experience treacherous, judgment difficult." The future of science does not depend so much on the number of scientists or the number of colleges, but rather on the individual qualities and the degree of perfection of a limited group of leading scientists and colleges. These are individual factors which require inherent talent which in turn is a condition evolved after generations of culture. Thus, very elaborate higher education for indiscriminate masses of humanity or students may not necessarily show the expected results. In other words, it is possible that higher specialized education should be given only to the few talented individuals, and their capacity and worth should be judged by as highly qualified and talented teachers. Quality is the greatest of all competitive aids. An essential qualification that must be possessed by a quality mineral industries college is a high caliber teaching staff, for the mineral sciences will advance in the coming years only if the leading minds of today are made avail- able as the mental springboards for our scientists of tomorrow. Mineral industries schools are finding it increasingly difficult to maintain a high caliber staff of instructors and administrators in competition with private business and governmental demands for similar

Jan 1, 1950

By D. Webster

It has been found that cold work and annealing treatments greatly retard subsequent grain growth and re-crystallization in thoria-dispersed nickel and NiCr. It is suggested that this is due to cavities which form at the particle-matrix interface durilzg cold work. Some of' the cavities formed are stable at elevated temperatures and prevent the mouement of large-angle grain boundaries. The movement of these boundaries at elevated temperatures is known to start recrystal-lization and when they are pinned by voids recrystal-lization is made more difficult. TD Nichro,me had a maximun resistance to recrystallization when the initial structure was coarse-grained and had a low dislocation density. A precipitation reaction occurred between 700° and 1200° F in cold-worked TD Nichrome. It has been shown by Grant and his coworkers1-3 that a large part of the strength of dispersion-hardened materials is a result of the cold-worked structure produced during fabrication. In a comparison of the strength of cold-worked copper with and without an oxide dispersion, Grant4 has demonstrated that there is little difference in strength at room temperature. The function of the dispersion is essentially to maintain the cold-worked structure at higher temperatures than is possible in the base material. The dispersion accomplishes this by making recrystallization more difficult. The mechanism by which this is achieved is discussed in this paper. The fabrication history of the material has been found to greatly influence recrystallization behavior and this aspect is discussed in some detail. I) MATERIAL Three different thoria-dispersed materials were examined. 1) DuPont 2 pet thoria-dispersed nickel (TDNi) in 0.050-in. seeet. Thoria particle size is in the range 100 to 2500A. 2) DuPont 2 pct thoria-dispersed nichrome (20 pet Cr, 80 pct Ni) (TDNiC) in 0.125-, 0.060-, and 0.040-in. sheet. In the as-received condition these sheets have

Jan 1, 1969

By H. A. Wheeler

That lead and zinc deposits are the result of prolonged,, slow deposition is the idea of most students of ore deposits, and in many cases, where the ore-bearing solutions have been very weak or the precipitating conditions have been very feeble, the ore accumulations have undoubtedly taken a long period of time. As these two vital conditions have been subject to great variations in the different mining camps, the following example is highly interesting in showing that deposition can be very rapid under favorable conditions, geologically speaking, and also extremely recent. In fact, the writer is inclined to regard most, if not all, of the Mississippi Valley deposits of lead and zinc as probably being very young, at least not older than Tertiary, if not Quarternary, in age. The extensive Joplin lead and zinc district, in southwestern Missouri, which is about 60 years old and has numerous mines that were abandoned from 1 to 50 years ago, shows that the lead and zinc today are in an active condition of solution and redeposition, although these two metals occur in the predominant form of sulfides. The mine waters from the older and more or less abandoned portions of the district are frequently so acid, mainly from the oxidation of associated pyrite, as to necessitate the use of wooden pipes and pumps. The first boom in the Oklahoma zinc fields, which is the southwestern extension of the Joplin district, occurred when ore was accidentally struck in drilling a water well. Among the mines then opened up was the Mission mine, at Lincolnville, Ottawa County, Okla. This mine was opened in 1903 in lean "sheet ground," or a flat blanket formation of chert carrying disseminated zinc blende, or "jack," and galena. Theore-body was very free from iron pyrites and the concentrates were very high grade, the "mineral," or lead concentrates, assayed 80 to 85 per cent. lead and the jack, or sphalerite, assayed 60 to 65 per cent. zinc. The orebody was very shallow, occurring at a depth of 76 to 95 ft. (22 to 28 m.) and very wet, requiring three or four pumps to handle the water. The mine was operated until 1914, when it was closed by litigation and immediately filled with water. The second Oklahoma boom, five years ago, opened up the large, active camps of Picher, Tar River, and Century, which are located 2 to 5 mi. west of Lincolnville. They are considerably deeper, being farther down on the westwardly dipping monocline that emanates from the Ozark

Jan 1, 1920

By George Bain

SOME problems concomitant with commercial exploitation of marble are presented as examples of interesting, useful and profitable fields for application of scientific knowledge. The marble industry is only one such field and is selected because its varying new aspects are familiar to the author. However, what is true for marble is equally so in principle for many industrial minerals. The problems of any stone industry are to maintain markets, create new outlets for stone already in demand, and develop varied uses for varieties that are not so popular. Here the geologist has a different role from most of his colleagues in metal mining. The producing branch may ask about the expectable variation in thickness or size of a deposit as development proceeds. The stock department may call for the available amount of a given type of stone before accepting a large order. The sales force requires data on the use for stone from certain parts of deposits in order to divert grades to the most suitable use. The service depart-ment wants defects rectified and the cause determined to avoid recurrence. The mills want data on durability and cutting quality of abrasives. The geologist occupies no special department; he is on general call, as may be illustrated by a few types of problems that may be classified as: (1) dominantly geological in character, (2) dominantly chemical in character, (3) dominantly physical in character.

Jan 1, 1940

By Basil B. Zavoico

The symposium on production for the year 1942 contains no papers on the foreign situation except those on Argentina and Mexico. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts From Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not determinable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a Rope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone.

Jan 1, 1943

By Leon W. Dupuy

Many articles have been written describing peculiar and particular types of drilling. Little correlation has been made between the character of ground to be drilled and sampled and the type of drilling most desirable for procuring satisfactory samples. In development work, the engineer and metallurgist often desire the recovery of a sample in as physically natural a condition as possible, particularly when the sample must provide material for process tests as well as chemical and physical analyses. This paper describes the results of experimentation in drilling unconsoli-dated materials carrying titanium minerals in the Magnet Cove area, Ark. The drilling was most difficult in that the ground varied much in consistency, and it was vitally necessary to recover a physically natural sample. Ordinary churn drilling recovered a sample that could be analyzed chemically, but the sample was not in its natural state. The problem was successfully solved by utilizing and further developing methods used in the oil and clay industries. In the Magnet Cove area of Hot Spring County, Ark., the titanium minerals include rutile, brookite, ana- tase, leucoxene, and others. They occur in soil, clays, and altered rocks adjacent to novaculite in contact meta-morphic deposits. In preparing titanium minerals for use in the industry, it is necessary to know the physical characteristics of the ore. Also it is believed that the particular physical character of the titanium mineral used is just as important as the chemical character. Brookite and rutile, for example, are the same chemically but differ in crystalline structure. In preparing titanium minerals for market, beneficia-tion is necessary. For the millman to make a satisfactory laboratory test, the sample he uses must be as nearly of the same physical character as he would have from mine run ore. In the past at Magnet Cove, churn drilling had been done on the properties, and assays of total titania had been obtained. It was found, however, that the total titania was indicative merely of the presence of titania but did not tell the metallurgist the character of the material or even give him the slightest indication of what he might expect to recover. When the Bureau of Mines entered the field in the winter of 1947 and 1948, it was therefore necessary that a natural sample be recovered. LIMITATlONS IN ORDINARY PRACTICE The churn drilling that had previously been done had shown that the occurrence of titanium-bearing mineral was somewhat widespread. The samples were, however, completely beaten up and in a finely powdered state. The minerals had been slimed, and such ore dressing tests as were made from the churn-drill samples were found to be worthless. Test pitting and outcrop sampling had provided satisfactory samples of surface ore but did not represent the entire ore body. A quantity of rutile had been produced from the surface residual concentrations in the westerly part of the cove, but production ran into metallurgical trouble as depth was attained. Representative deep samples upon which ore dressing research might depend were needed.

Jan 1, 1950

By A. B. Kinzel

Precise knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly .ell known. General Method The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By Thomas Harris

This paper. was written in conjunction with the work being undertaken by the Technical Committees on Classification of Coal, and an effort has been made to compile information relative to the use of coal for stationary steam generation in order to use this information to assist the Committee on Classification of Coal for the ultimate purpose of elimination of losses both by the' reduction of indivi-dual effort and waste in the consumption of material. Under the auspices of the National Association of Purchasing Agents, a questionnaire was drawn up to develop this information from stationary steam plants throughout the United States. in order to consolidate the information de-veloped from the many hundreds of boiler tests on coals consumed by various coal¬burning equipment. These questionnaires covered: 1. The company reporting, location and method of delivery to the plant. 2. Complete coal date, including description of coals used (with. sufficient space to- include first, second and third, preference) on--source of coal used,- complete-analysis and factors affecting choice of, coal used. 3. Plant data, divided into - A. Hand fired, B. Overfeed stokers,. . C. Underfeed stokers, D. Traveling grate stokers, E. Pulverized coal, and included complete description of furnace data, draft data, coal-burning rate, type of stoker, type of pulverizer, efficiency date and remarks.

Jan 1, 1933