Search Documents

By K. E. Gray, G. M. Myers

In previous publications,5 results of single-blow bit tooth impacts on saturated rocks at various stress states were reported. This paper extends these earlier works to include study of bit impact tests on salt water-saturated Berea and Bandera sandstone samples under conditions of elevated confining and pore pressure. During the tests dynamic filtration and deposition of a mud cake were occurring due to the presence of drilling mud in the borehole and a borebole-to-formation pressure differential. Results indicate that saturation of these sandstones with salt water tends to make them weaker than when saturated with nonreactive fluids. Plastic failure often occurs even when extremely high fluid-loss muds are present in the borehole. The failure mode tends toward plasticity with decreasing fluid loss. Brittle failure of sandstones in mud-filled holes is apparently relatively rare. Depending on the stress level, and the associated failure mode, withdrawal of the bit tooth induces a tensile force that seems rather important relative to the quantity of rock removed by vertical tooth impact. INTRODUCTION A vast majority of the oil wells drilled today involve the use of colloidal muds having a measurable mud filtrate loss. It is known from field experience that reduction of the water loss of a mud generally results in a reduction of the penetration rate. This paper describes an investigation of crater formation at simulated bottom-hole pressure conditions for drilling fluids having different water losses. The literature on single bit tooth impact (cratering) at atmospheric conditions is extensive, but only a limited amount of work has been performed at the stress conditions similar to that found in oil wells. Spherical penetrator cratering tests on rocks at hydrostatic pressure were performed by Payne and Chippenda1e.1 Chisel impact studies on limestone with independently varying overburden and borehole pressure and atmospheric pore pressure were reported by Garner, et al.2 Gnirk and Cheatham3 performed "static" penetrator tests on dry rocks at equal overburden and borehole pressures. Podio and Gray4 studied the effect of pore fluid viscosity at atmospheric pore and borehole pressures and varying overburden pressures. Their results illustrated the importance of fluid saturation of the rock. Yang and Gray5 reported single tooth impact tests on saturated rocks at elevated borehole, pore and confining pressures, but with equal pore and borehole pressures. For the work reported in Refs. 4 and 5, filtration across the hole bottom purposely was avoided. Maurer6 has investigated the effect of independently varying pore and borehole pressures at elevated overburden pressures by using a zero water-loss mud in the borehole. His tests were carried out under conditions that allowed independent control of overburden, pore and borehole pressures, but without control of filtration at the hole bottom. EXPERIMENTAL APPARATUS AND PROCEDURE APPARATUS The single blow chisel impact apparatus used by Garner,2 as modified for this study, is shown in Fig. 1. A cross section of the pressure vessel is shown in Fig. 2. Several pieces of auxiliary equipment were added to the original apparatus in order that the borehole and pore pressure could be applied in a manner analogous to the actual bottom-hole situation. The pore-pressure system included a filtrate volume-measuring transducer and had sufficient surge capacity to allow filtrate to be injected into the sample without significant changes in pore pressure at points remote to the borehole. The borehole-pressure system contained a cross connection to the pore-pressure system so that both systems could be pressured simultaneously. The borehole-pore pressure differential was applied rapidly by the use of a quick and full-opening valve. The operation of this valve triggered two industrial

Jan 1, 1969

By Lawrence A. Shepard, Richard H. Krock

A series of ductile, two phase W-Ni-Fe composites, sintered in the presence of a liquid phase, were tested in tension. Identical room temperature stress-strain curves were obtained for specimens containing from 80 to 92 wt pct W (58 to 75 vol pct W particles). The composites exhibited a maximum elongation of 29pct at room temperature, and 10.7 pct at 77 °K. The tungsten particles in the composite elongated by the same amount at these temperatures. Single-phase alloy specimens matching the composition of the composite matrix showed about one half the flow stress of the composites. The test results demonstrated that the mechanical properties of W-Ni-Fe composites are determined by the tungsten particles alone and are independent of matrix volume fraction or mean free path over the composition range studied. A general prediction of the plastic behavior of two-phase alloys or composites from a knowledge of the properties, size, shape, and dispersion of the individual components is not, at present, possible. The excellent theoretical and experimental exposition of the dispersion-strengthening problem applies only to cases where the stronger phase is present as fine particles and in volume fractions of a few percent. Materials in which the stronger phase constitutes a significant fraction of the volume, although of broad engineering interest, have received comparatively little analytical attention. This important group of materials is the concern of the present study. The degree of deformation of each phase during the plastic working of a ductile two-phase alloy has been established by Boas and Honeycombe,1 Clare-brough,2 and Clarebrough and berger.3 These workers empirically correlated the recrystallization temperature of the individual phases with the degree of cold work sustained by each. It was shown that the deformations of both phases are equal and therefore the same as that sustained by the composite whole when the volume fraction of the stronger phase exceeds 35 pct. At yielding, however, deformation begins in the weaker phase. A direct correlation of composite strength, as a function of deformation, with the strength of the individual components cannot be made. In the presence of stronger phase particles, the flow stress of the weaker matrix phase is enhanced by an additional hydrostatic component. The development and potential magnitude of matrix strength promotion upon straining has not even been experimentally established. Quantitative work in this field has been confined to ceramic-metal composites. These materials fracture at strains considerably below 1 pct by cracking of the ceramic particles.4-6 An indication of the potential constrained matrix strength capacity is given by the observation by Nishimatsu and Gur-land4 that the maximum tensile strength of a WC-Co composite is almost double the bulk strength of the cobalt matrix. The relationship between composite strength and geometry is ordinarily expressed in terms of the mean-free matrix path (referred to subsequently as MFP) between the stronger particles.* This factor takes into account both the volume fraction of matrix phase and the average size of the particles. unke17 concluded that composite strength varied directly with the decreasing log MFP, following the Gen-samer8 relationship. However, Gurland and ~radzil~ reported a strength maximum at an MFP of the order of 1 p in WC-Co composites. A ductile two phase metallic composite was chosen for the present investigation of composite mechanical properties with the view of avoiding the difficulties and ambiguities noted above. The W-Ni-Fe heavy alloy of Green, Jones, and pitkin9 contains 80 to 94 wt pct W, and nickel and iron in a weight ratio

Jan 1, 1963

By J. J. Gilman

The data presented indicate that the critical shear stress and strain-hardening Thedatapresentedrate of a zinc monocrystal depend on the orientation of its slip direction with respect to its external boundaries. The tendency of a crystal to form deformation bands also depends on its shape. THE plastic behavior of pairs of zinc monocrystals in which both members of the respective pairs had the same orientation with respect to the longitudinal axis, but each had different orientations with respect to their rectangular external shapes, were compared in this investigation. The purpose of the investigation was to see what influence the shape or surface of a zinc crystal has on its mechanical properties. In a previous investigation of triangular zinc monocrystals,1 anomalous axial twisting was observed which seemed to be related to the triangular shape of the crystals. Wolff,' in 400°C tensile tests of rectangular rock-salt crystals bounded by cubic cleavage planes, found that, of the four equivalent slip systems, the two with the "shorter" slip directions yielded and produced slip lines at lower stresses than the other two. This observation and the work of Dommerich³ as formulated by Smekal4 as a "new slip condition" for rock-salt: "among two or more slip systems permitted by the shear stress law, with reference to the formation of visible slip lines by large individual glides, that slip system is preferred which has the shortest effective slip direction." More recently, Wu and Smoluchowski5 reported essentially the same effect for ribbon-like (20x2x0.2 mm) aluminum crystals at room temperature. Experimental Chemically pure zinc (99.999 pct Zn), purchased from the New Jersey Zinc Co., was the raw material. Glass envelopes, containing graphite molds and zinc, were evacuated while hot enough to outgas the graphite but not melt the zinc. At a vacuum of about 0.2 micron the envelopes were sealed off and then lowered through a furnace at 1 in. per hr so as to melt and resolidify the zinc and produce mono-crystals. One-half of one of the molds is shown in Fig. la. Each mold consisted of four pieces from a cylindrical graphite rod that was split longitudinally and transversely at its midpoints. Rectangular milled grooves 0.050 in. deep and % in. wide formed the mold cavity when the split halves were assembled with twisted wires. Fig. lb shows the specimen shape obtained when the top and bottom mold-halves were rotated 90" with respect to each other. Good fits prevented leakage and excess zinc was necessary to provide enough liquid head to fill the mold completely. In removing soft crystals from the molds it was impossible to avoid small amounts of bending. However, manipulations were carried out whenever possible with the crystals protected by grooved brass blocks. All specimens were annealed prior to testing. From the top and bottom sections of each crystal, X-ray specimens and tensile specimens 7 to 8 cm long were sawed. The tensile specimens were annealed inside evacuated tubes for 1 hr at 375°C. Next the crystals were cleaned and polished by 2-min dips in a solution of 22 pct chromic acid, 74 pct water, 2.5 pct sulphuric acid, and 1.5 pct glacial acetic acid.' Cleaning was followed by a 10-sec dip in a 10 pct caustic solution, then washed in water and alcohol, and dried. This treatment results in a bright surface covered by an invisible oxide film. The testing grips were a slotted type with set screws and were supported in a V-block during the mounting operations in order to avoid bending the crystals. A schematic diagram of the recording tensile-testing machine is shown in Fig. 2. The machine has been described elsewhere.' The head speed was 0.3 mm per sec for all tests. The crystal orientations were determined by the Greninger X-ray back-reflection method with an estimated accuracy of 1. Description of Crystal Geometry A schematic picture of a rectangular zinc mono-crystal is shown in Fig. 3. ABD designates the front edge of a basal plane (0001) of the crystal, the only active slip plane for zinc at room temperature. Of the three possible (2110) slip directions, the active one is indicated by an arrow. Cartesian coordinates are taken parallel to the specimen edges. The normal, n, to the basal plane (n is parallel to the hexagonal axis) has the direction cosines a, ß and ?. X0 = 90 — y is the angle between the longitudinal axis and

Jan 1, 1954

By G. H. Bishop

The kinetics of the inter granular penetration and embrittlement of [100] tilt boundaries in 99.998 pct pure nickel upon exposure to bismuth-rich Ni-Bi liquids have been determined in the temperature range from 700° to 900°C. The kinetics of penetration are parabolic in time at constant temperature over most of the temperature range. In a series of 43-deg bicrystals the rate of penetration is anisotropic with respect to the direction of penetration into the grain boundaries. In lower-angle bicrystals the penetration rate is isotropic. The rate of penetration decreases with tilt angle at 700°C. The activation energy for penetration in the 43-deg bicrystals is 42 kcal per g-atom independent of direction. It is concluded that the intergranular penetration and embrittlement in the presence of the liquid proceeds by a grain boundary diffusion process and not by the intrusion of a liquid film. This was confirmed by a determination that the kinetics of penetration and embrittlement were the same in the 43-deg bicrystals upon exposure to bismuth vapor under conditions such that no bulk liquid phase would be thermodynamically stable. WhEN solid metals are exposed to a corrosive liquid-metal environment, the grain boundaries are sites of preferential attack. Depending on the temperature, the composition of the liquid, and the composition, structure, and state of stress of the solid, a number of modes of attack are possible. This paper reports a study of the kinetics of intergranular penetration and embrittlement of high-purity nickel bicrystals upon exposure to bismuth which, together with an earlier study by Cheney, Hochgraf, and Spencer,&apos; demonstrates that there are at least two modes of intergranular attack possible in the Ni-Bi system. In the study by Cheney et al., columnar-grain specimens of 99.5 pct pure nickel were exposed to liquid bismuth presaturated with nickel in the temperature range 670" to 1050°C. They found that the majority of the boundaries, which were predominantely high-angle boundaries, were penetrated by capillary liquid films, the attack proceeding by a process which will be termed grain boundary wetting. This process occurs in a stress-free solid when twice the liquid-solid surface tension is less than the surface tension of the grain boundary,* i.e., when 2yLs < YGB In this case the penetration of the grain boundary by the liquid occurs at a relatively rapid rate, resulting in the severe embrittlement of a polycrystalline solid. Grain boundary wetting is a common mode of intergranular attack in systems in which the lower melting component is relatively insoluble in the solid, but the solid has an appreciable solubility in the liquid, for example, the Ni-Bi system, Fig. 1. In systems of this type at temperatures above the range of stability of any intermetallic phases, once the liquid is saturated with respect to the solid so that no gross solution occurs, chemical gradients are small, and surface tensions become major driving forces for attack, provided the solid is stress-free. The results of Cheney et al. appear to be typical of those encountered when grain boundary wetting occurs.&apos; Capillary films were observed in the boundaries after quenching from the exposure temperature. The mean depth of penetration increased linearly with time, and the activation energy for the process was found to be 22 kcal per g-atom. In a study of the Cu-Bi system Yukawa and sinott4 found that the depth of penetration of bismuth into high-purity copper bicrystals of orientations from 22 to 63 deg of tilt about (100) at 649°C ranged from 0.05 to 0.25 in. after a 12-hr anneal. This corresponds to a linear rate of 6 to 15 X 10~6 cm per sec. At the same reduced temperature of 0.68 the rate for the Ni-Bi system&apos; was 7 x lo-&apos; cm per sec. In another study of the Cu-Bi system, Scheil and schess15 determined the kinetics of grain boundary wetting in hot-worked commercial rod. While there were several complicating factors present in this study, there is general agreement with the above results. The kinetics of penetration were linear, the activation energy was 20 kcal per g-atom, and at 650°C the rate of wetting was 2 to 5 x 10-6 cm per sec. The rate of wetting in the A1-Ga system6 is somewhat

Jan 1, 1969

By E. Teghtsoonian, E. M. Schulson

The tensile behavior of bcc ordered P&apos; AuZn single crystals (CsCl structure) has been investigated under varying conditions of temperature, composition, and orientation. Between -0.2 and 0.4 T, multi-stage hardening occurs fm stoichiometric and nonstoichio-metric crystals oriented near the middle of the primary stereographic triangle. At higher and lower temperatures, parabolic type hardening occurs, followed by work - softening at the higher temperatwes. Deviations from stoichiometry give rise to increased flow stresses. Multi-stage hardening was observed for most orientations, except along the [loll-[lll] boundary and near the [001] corner of the stereo -graphic triangle, where parabolic type hardening occurs. Along two slip systems, (hk0)[001] and (, operate simultaneously while in the [001] comer, slip occurs mainly on the system. Electron microscopy of deformed crystals revealed bundles of edge dislocations forming walls approximately Perpendicular to the glide plane. In general the plasticity of 4&apos; AuZn closely resembles the plasticity of bcc crystals. In recent years, considerable interest has arisen concerning the mechanical properties of the CsCl type intermetallic compounds Ag Mg,&apos;- Fe co,&apos; and Ni Al.&apos;-&apos; The compound P&apos;AuZn is structurally similar. It has a low and congruent melting point of 725"~,&apos;" remains ordered up to the melting point,16 and pos-esses a range of solid solubility from 47.5 to 52.0 at. pct Au at room temperature.15 The present paper reports the results of an investigation on the general tensile behavior of material in single crystal form. Some dislocation configurations characteristic of the deformed state are also reported. The results of a detailed study of the slip geometry in AuZn are presented in a separate paper.17 PROCEDURE Alloy preparation, crystal growing techniques, and the procedure followed in selecting specimens of minimum composition variation are reported elsewhere.17 Dumb-bell shaped tensile specimens were prepared by carefully machining single crystals in a jewellers&apos; lathe to a gage length of 0.80 in. and diam of 0.090 in. Back-reflection Laue X-ray patterns and room temperature tensile tests revealed that machining damage could be eliminated by electrochemically polishing 0.005 in. from the machined surface followed by annealing at 300°C for 1 hr. Specimens were polished in fresh 5 pct KCN solution (40°C, 12 v). Experiments were performed by gripping specimens in a self-aligning pin-chuck and threaded collet system, then straining in a floor model Instron tensile machine. All tests were performed in duplicate. Experimental variables included temperature, composition, and orientation. Unless otherwise stated the strain rate was 2.5 x 10"3 per sec. Liquid testing environments included nitrogen (WOK), nitrogen cooled petroleum ether (133" to 293"K), and silicone oil (293" to 488°K). Resolved shear stress-shear strain curves were electronically computed from autographically recorded load-elongation curves. Stress and strain were resolved on the macroscopic noncrystallographic (hkO) [001] system operative under the specific test conditions of temperature, strain rate, and orientation reported earlier.17 RESULTS The temperature dependence of the work-hardening curves is shown in Fig. 1 for gold-rich crystals of 51.0 at. pct Au oriented near the center of the stereo-graphic triangle. Over the range of intermediate temperatures from -200" to 400°K, they are very similar to those classically observed for fcc metals (reviewed by Nabarro et al.).&apos;&apos; The beginning of deformation is characterized by a region of decreasing hardening rate, stage 0, which is followed by a region of low linear hardening, stage I, and then a region of higher linear hardening, stage 11. At the higher temperatures, stage 111 is observed, a region of decreasing hardening rate. Over the intermediate temperature range, the extent of stage 0 and of the slow transition between stages I and I1 decreases with increasing temperature. Total ductility is large, often greater than 300 pct shear. As the temperature is either increased or decreased, the extent of stage I is decreased, giving rise to parabolic type flow and reduced ductility. Similar temperature effects have been reported for bcc ~r~stals.~~-~~ Below -14O°K, hardening is terminated in brittle fracture while above -400°K. initial hardening is followed first by work-softening and then by chisel-edge type ductile fracture. Stoichiometric (50.0 at. pct Au) and Zn-rich (51.0 at. pct Zn) crystals were also tested from 77" to -500°K. The effect of composition on the flow behavior is illus-

Jan 1, 1970

By F. J. Schuh

The drilling industry long has been plagued by failures in the bottom few joints of surface and intermediate casing strings. This paper presents an analysis of the various possible causes of failure and concludes that failures are caused by short-lived, high-energy torque impulses delivered from the drill string through the bit while drilling out the cementing plugs, cement and floating equipment. The magnitude of these torque impulses is shown to be a function of the rotational momentum of the drill string, and a method is derived to calculate the magnitude of these impulses. The available methods of strengthening the bottom joints are reviewed. It is concluded that, while present methods are ineffective, a combination of improved procedures for strengthening and minor restrictions on drillout practices will prevent failures. Introduction In most cases, failure in the bottom few joints of casing strings is not discovered until electric logs record that the bottom one, two or three joints have parted from the casing string and slipped down the hole. However, in some cases the parted section of casing uncovers a high-pressure or lost circulation zone, or shifts laterally restricting the passage of drilling equipment. In these instances extensive remedial work is required to realign the parted pieces and seal the exposed formations. Several methods used to strengthen the bottom joints of casing strings include locking set screws in the couplings, putting wedges in special collars, welding straps across the couplings, welding the couplings and, most recently, using epoxy resin-based, thread-locking compounds. Since none of these techniques has eliminated the problem, this study was initiated to find the cause of failures and to evaluate the available methods of prevention. Mechanics of Casing Failures An analysis of the various possible causes of failure indicates that the casing is unscrewed rather than broken and that therefore failure must occur before the shoe is drilled. Since there is no general agreement as to the causes of casing failure, some possible mechanisms were ATLANTIC RICHFIELD CO. DALLAS, TEX. considered in this analysis. Failure of the bottom joints of casing can occur by only one of three types of stress: tension, torsion or bending. The possible mechanisms of failure were evaluated by determining the forces required to cause casing failure by each of the stresses; and, where applicable, the possibility of failure by fatigue was considered. For casing to part under tension requires a downward load of more than the tensile strength of the casing. The lightest API weight H-40 grade casing requires a bit load on the bottom of the casing of 27,000 to 34,000 Ib per inch of bit diameter (Table 1). Since maximum drill collar weights seldom exceed 10,000 Ib per inch of bit diameter, it is apparent that casing strings cannot be parted by the downward load of the drill string. The second mechanism considered was failure by bending. This mechanism requires that the lowermost casing joints be free to be deflected laterally until the bending stress exceeds the strength of the pipe. To fail, the casing (at a height L above the shoe) requires a force and deflection&apos; at the shoe of To deflect the casing shoe with the drill string obviously requires a dog-leg at the casing shoe. This dog-leg must have a rate of change equal to or greater than the change in curvature of the deflected casing, which is given by

Jan 1, 1969

By A. J. Shaler

The subject of the mechanism of sintering has received much attention in the past few years, particularly since the beginning of the series of AIME seminars in powder metallurgy of which this paper introduces the fourth. In the first of these, F. N. Rhines1 brought together and discussed the available experimental data on the sintering of pure metallic powder, and succeeded in bringing to a sharp focus the attention of workers in this field on the established observations which a satisfactory theory must explain. Several other authors3,5,6 have, in the last few years, studied the phenomena that occur when cold metallic powders, loose or in the form of compacts, are first brought to elevated temperatures. Some workers&apos; in the field of friction have recently studied the adhesion of solid metal surfaces when they are brought into close contact. These researches have indicated that several separate mechanisms operate simultaneously, at least during the first part of the sintering process. Some of them have been called transient mechanisms4 because they are in general not absolutely necessary to sintering. Powders may be so prepared and so treated that these transient phenomena do not take place during subsequent sintering. This does not mean, of course, that their industrial and scientific importance is any less than that of the steady-state phenomena. The latter are changes that go on during sintering no matter how the powders are made or treated; they cannot be divorced from sintering. One way to analyze the process of sintering into its component parts is perhaps to distinguish between these transient and steady-state phenomena. Some of the transient phenomena have been studied in the past few years. Huttig3 has shown that, when the temperature of metallic powder is slowly raised, the following events generally occur in order: (1) physically adsorbed gases are desorbed; (2) there is an atomic rearrangement of the surface, a sort of two-dimensional "surface-reciystallization"; (3) there is a breakdown of chemically adsorbed surface compounds; (4) there is a recrystalliza-tion in the volume of the metal. All these changes are shown by Huttig and his coworkers to be completed fairly rapidly at lower temperatures than those generally used in sintering and are therefore not a part of the mechanism whereby the density of a mass of powder continues to change after long heating at an elevated temperature. But the first and third of these changes release gases in quantities which may or may not help to control the steady-state mechanisms, depending on when the voids become isolated from the outside of the compact. Among the phenomena studied by Steinberg and Wulff,8 there is the effect on sintering of residual stresses arising from the pressing operation. They found that the lateral surfaces of a green compact of iron are under a longitudinal residual tension-stress of the order of magnitude of half the yield-point for solid iron. If the outside surface is in tension, the core must be under longitudinal compression. When the compact is heated, the surface residual stress is thermally relieved first, and the compact therefore initially expands in the direction of its axis. This is a transient phenomenon, if for no other reason than the possibility of sintering unpressed powders, as demonstrated by Delisle,9 Libsch, Volterra and Wulff10 and others.1 The subject of recrystallization is dealt with further in a separate section, in view of its prominent place in sintering literature. It, too. is one of these transient phenomena. Among the steady-state parts there may be distinguished the attraction between particles and its consequences, the spheroidization of voids in the compacts, and the densification or swelling of the compact. There is considerable evidence4,7 showing that cold metallic surfaces, when brought to within a few interatomic distances of one another, are attracted to each other by forces of the order of many thousands of pounds per square inch. A calculation, discussed in greater detail in another section, shows that this force changes but slightly when the temperature of the surfaces approaches the melting point. Actual measurements of forces of adhesion of this magnitude have been made by Bradley12 on some nonmetals, but none has yet been made on cold or hot metals. This force is of sufficient magnitude to cause some plastic deformation in powder compacts, as will be shown below. A second force of steady-state nature is due to the surface tension, which probably has the same origin as the force of attraction between surfaces.164 A paper by Udin, Shaler, and Wulff1,3 gives the results of precise direct measurements of its value for solid copper. The demonstration of the tendency for the surface tension to shrink a pore was long ago given by Gibbs.17 He showed that its effect on a curved surface between two phases is equivalent to a pressure perpendicular to that

Jan 1, 1950

By W. B. Mather

R. G. Wuerker (University of Illinois, Urbana)—Mr. Mather is to be congratulated for stressing the most urgent need for a program of testing the physical properties of rocks, as they are encountered by the petroleum engineers on their drilling jobs and by the miners on their excavating, roof control and mineral preparation tasks. Another valuable source of information is the Handbook of Physical Constants.22 It stresses the physicist&apos;s approach rather than the engineer&apos;s procedure. The study of hardness, and rock hardness in particular, is beset with many difficulties. There is no satisfactory definition of hardness yet, and the term hardness is used to describe a number of quite dif- ferent properties. Hardness tests are grouped into static and dynamic determinations. They should be expressed with reference to the mechanical action of the applied force, like indentation hardness, scratch hardness, abrasion hardness, rebound hardness. A discussion of all these various hardness tests and of the special difficulties encountered in hardness testing of such heterogeneous material as rocks is given in the U. S. Bureau of Mines&apos; standard proposal. The more critical student may be referred to the book by D. Landau: Hardness, which is in my opinion the best existing treatise on this subject.

Jan 1, 1952

By Gen-Hua Shi, William Boyle, Richard E. Goodman

This keynote paper calls attention to two critically important issues relating to selecting supports for excavations in hard rock. The first is the proportion of the ultimate sliding volume that needs to be stabilized by the support system. Some excavations can be imagined to liberate very large rock volumes, whose weight can not be assigned to supports without severe economic penalty. Using the keyblock principle, it is argued that only the most critically oriented and finite blocks right on the periphery of the opening have to be supported; if these are retained by the support system, or by self resistance due to friction on the sliding faces, then the blocks behind will remain in place. As all concepts, this one has bounds and limits. Since the keyblock analysis for rock engineering is very new, these limits are not yet understood ... The second issue is the degree to which possibly stabilizing forces associated with the in-situ stress field ought to be accepted as support for potential keyblocks. It is shown that the initial stress can be effective in stabilizing rock wedges whose faces are nearly perpendicular to the excavation surface. It is too early to decide this issue but important to consider it.

Jan 1, 1982

By A. E. Gorum, I. Cornet

Fatigrle of ionic crystals has been studied primarily in magnesinm oxide. under cyclic stress dislocations move irrreversibly; they multiply; slip bands form and grow; cracks mucleate and propagnte, and failure occurs. The use of ionic crystals such as MgO is advantageorus in such investigations because they are optically transparent. Individual dislocation Intersections with {100} surfaces may be observed with a standard microscope, using etch-pit techniques. Slip, deformation, crack .formation, and fracture in MgO crystals under cyclic stress are compared with cotrresponditzg processes in metals. ThE effect of cyclic loading in metals has been studied for many years. The appearance of slip lines is readily observed and the ensuing fracture may also be seen. From these observations it is possible to predict the behavior of a material and make an educated guess as to what is happening internally, but the actual changes taking place within the structure are not readily apparent. If one could obtain a material in which the individual glide components could be observed, it would be invaluable in determining the actual slip distribution resulting from cyclic loading as well as the distribution of slip in the neighborhood of a growing crack. Such a material is magnesium oxide. Dislocation arrays may be observed by means of etch pits

Jan 1, 1961

By R. W. Armstrong, P. C. Jindal

The hardness dependence on grain size for polycrys-talline cartridge brass and a leaded brass has been measured by Brine11 and Rockwell B testing. In each case, the hardness, H, depends on the average grain diameter, 1, according to: H =Ho + kHl-1/2 where Ho and kH are experimental constants. Diamond pyramid hardness values have also been measured as a function of the indentation size and grain size to give additional information on the nature of the hardness test and the dependence of hardness on micro-structure. The hardness of polycrystalline brass depends on its grain size. Bassett and Davis&apos; demonstrated this as early as 1919 by making Brinell hardness measurements on cartridge brass. Since then, the hardness of this type of material has been measured as a function of grain size by making Rockwell,2&apos;3 Vickers,4 and Brinell5 tests. he hardness dependence on grain size has also been measured for other materials. Angus and summers6 investigated the grain size dependence of the Brinell hardness of polycrystalline copper and a Cu-4.5 pct Sn bronze. In other studies, nickel,? Armco iron,Big an Fe-0.07 pct C alloy,I0 and an 0.39 pct C-12.45 pct Cr stainless steel" have been investigated. In some of the preceding cases, the hardness results have been analyzed to show that the hardness varies with the average grain diameter, 1, according to an l-l\4, l-1/4 or I-2 dependence,11-13 The studies of the influence of grain size on hardness have not been based on any theoretical model. This may be because the hardness of a material is itself a complicated property. However, attempts have been made to correlate, experimentally and theoretically, the hardness of a material with its unidirectional stress-strain behavior.14-l6 On this basis, Hall" proposed that the polycrystal hardness dependence on grain size might follow directly from the Hall-Petch18,19 relation for the grain size dependence of the yield stress. Thus, the hardness-grain size relation was given as: H = Ho + kHl-1/2 [1] where Ho and kH were taken as experimental constants. The relation was applied to the measurements on brass,&apos; copper,6 bronze,= and Armco iron.&apos; More recently, this relation was shown by Armstrong and jindal20 to adequately describe the measurements on cartridge brass made by Bassett and Davis&apos; and Babyak and Rhines.5 In this case, the relationship was taken a step further by independently relating the values of Ho and kH to the values of oyand ky, previously reported by Armstrong, Codd, Douthwaite, and petch21 from measurements of the yield stress dependence on grain size for this type of material. In the present investigation, new Brinell and Rockwell B hardness measurements have been made as a function of grain size for a cartridge brass and a leaded brass. In addition, diamond pyramid hardness values were measured as a function of the indentation size. All these results are applied to a further analysis of the hardness dependence on grain size. MATERIALS AND EXPERIMENTAL METHODS Cartridge brass and a leaded brass were selected for this investigation for two main reasons: it was anticipated 1) that these materials could be cold-worked and recrystallized to a wide range in grain size and 2) that the results to be obtained on these typical industrial materials could be usefully compared with previous investigations. The chemical analyses of the actual materials which were employed are given in Table I. The as-received 1/2- and 3/4-in.-thick plates were given various reductions in thickness by cold rolling. The rolled material was heat-treated at various temperatures between 330" and 850°C for differing time periods from 5 min to 9 hr to achieve a variation in the average grain diameter between 0.0339 and 0.000543 cm.22 During heat treatment, the brass was protected from zinc loss by packing it in chips or foils of the same composition material. Reasonably equi-axed grain structures were obtained in each case. The metallurgical grain sizes of the specimens were determined from measurements of the average linear intercept on a random line. Annealing twin interfaces were not counted along with grain boundaries. The

Jan 1, 1970

By L. A. Panek

During the past three years, USBM has developed an apparatus and technique for direct measurement of existing pressure and change of pressure in mine rock. This relatively simple and inexpensive monitor is reliable for months after being installed. It is used to determine shift of ground pressure created by different sequences of mining, to ascertain the cause of rock failures, and to evaluate the need for artificial support. The technique has been employed to measure pressures in limestone, greywacke, concrete, diabase, and soft iron ore. When rock is subjected to a load it is deformed. Ordinarily this is observed in a mine as the displacement of one point with respect to another—the deflection of the roof, which may be observed as a convergence between roof and floor; or the extrusion of material from the rib, which may be observed as a decrease of the distance between the rib and the post of a timber set. The effect of excessive pressure may be a rockburst if the rock is strong, or it may be squeezing ground if the rock is soft. Some desirable effects of high stress (high in relation to strength) are the caving of roof in a longwall mining operation, the caving of ore in block caving, and the decrease in mechanical energy required to break down the mineral seam in a retreating pillar-robbing operation. In any case, whether the observable effect of rock load is desirable or undesirable, it is a displacement, and depends on the following four factors: 1) The structure—the size and shape of openings, pillars, and linings, the geologic bedding and jointing. 2) The mechanical properties of the rock—prin-cipally the strength, modulus of elasticity, and flow characteristics. 3) The load or applied stress—primary sources are the weight of superincumbent rock, which increases with depth, and unrelieved tectonic stresses; secondary sources are redistributed pressures caused by other nearby openings, especially large mined out zones (rock pressure depends partly on the rock structure created by mining). 4) Duration of load, related to the length of time the opening is exposed. CONTROL OF ROCK DISPLACEMENT Rock displacement can be controlled by control of these four factors. Consider now the means of exercising such control over these factors. Control of the structural features is obviously possible to a great extent, as such control is exercised largely by choosing the method of mining and the methods of natural and artificial support. Rock properties vary, even within a particular mine, but they are controllable only in the limited sense that control may be exercised by choosing the beds or zones to be mined so that rocks with undesirable properties will not occupy critical positions within the rock structure created by mining. Rock pressure is the most complex of the four factors through which ground control can be achieved because it is invisible, difficult to measure, and poorly understood. Rock pressure is controllable only to the extent that control is exercised on the rock structure created by mining. Considering openings within a particular mine, time of exposure varies, and is readily controllable because it is easily measured and easily understood — the longer an opening stands, the greater the likelihood of failure or excessive convergence. Control is exercised by choice of an appropriate sequence of driving openings of different classes, such as haul-ageways and rooms, which are required to remain well supported for different lengths of time under different conditions. Again, control is exercised through the method of mining. All controllable factors can be controlled by proper design of the mining method. The orientation and relative positions of the mine workings and the sequence of their excavation are likely to be much more important to ground control than is the design of artificial support. This implies that the major decisions in regard to ground control are made, knowingly or not, at the time the mining method is chosen. WHY MEASURE ROCK PRESSURE In addition to restrictions on the several factors, control implies the measurement of these factors in some sense, whether only qualitatively by visual observation, or by actual quantitative determination with a measuring instrument. Rock pressure is the most difficult of these factors to measure, largely because of the interaction between the measuring device and the rock. Nevertheless, the quantitative

Jan 1, 1961

By R. M. N. Pelloux

This study of aluminum-copper alloys had two aims: 1) To determine the effect of the amount and distribution of a second phase, CuAl2, on the creep-rupture strength, ductility, and fracture characteristics of the alloys. The work of Gemmell and grant&apos; on single-phase aluminum-copper alloys provided a basis for the present study. 2) To attempt to provide a relation between the microstructure and strength of two-phase alloys deformed at comparatively high temperatures (greater than 0.45 T,). The creep behavior of the two-phase magnesium alloys Mg;Ce and Mg-A1, has been treated by Roberts. 9 In work reported by Sully and Hardy4 and by Underwood, Marsh, and Manning~ on A1-Cu two-phase alloys, and also in a portion of the work of Gemmell and grant,&apos; aging took place during the creep tests. &apos;In the present work, overaged aluminum-copper alloys were subjected to creep deformation at two temperatures, 500 and 700OF. The overaging treatments to produce the precipitate dispersions were performed prior to the test, at temperatures which were the same as the ultimate respective test temperatures. Hence, the present study is concerned with the creep behavior of stable (in contrast to "underaged") two-phase A1-Cu alloys, i.e., alloys in which no depletion of the solid-solution matrix occurred during: creep. MATERIALS AND PROCEDURE A 2 and a 3 pct Cu alloy, supplied by Alcoa, were studied; Table I shows the compositions. The grain size of the specimens, 0.9 to 1.0 mm, was achieved by annealing the machined test bars for 2 hr at 1000°F, followed by furnace-cooling to 900°F, and homogenizing for 4 hr. Both compositions are in the single-phase condition at 900°F. Two types of overaged dispersions, termed "over-aged I" and "overaged 11" were prepared after the grain size and the homogenization anneals. The overaged I alloys were prepared by quenching to room temperature after homogenization, aging at either 500&apos; or 700°F for 72 hr, and air-cooling to room temperature. The overaged I1 alloys were prepared by furnace-cooling after homogenization, to either 500&apos; or 700°F, and holding at the necessary temperature for 72 hr. The times for furnace-cooling from 900°F to 700° and 500°F were, respectively, about 2 and 3.5 hr. The structures of the A1-2 pct Cu alloys are shown in Fig. 1 (overaged I) and in Fig. 2 (overaged 11). A comparison of Figs. 1 and 2 shows that in the overaged I alloys the precipitate particles along the grain boundaries are much more closely spaced and the grain boundaries are straighter than they are in the overaged I1 alloys. Further, the particle size and spacing in the grains are smaller than in the overaged I1 alloys. Microstructures of the A1-3 pct Cu alloys have not been shown; the structures of these alloys differed from those of the A1-2 pct Cu alloys only in that the distribution density of the particles was greater. The creep specimens had a gage section 1 in. long with a diameter of 0.155 to 0.195 in. Before testing, specimens were electropolished in a solution of 100 cc glacial acetic acid, and 30 cc of 60 pct perchloric acid, at 40&apos; to 50°F, at 24 v. The specimens were kept refrigerated prior to testing to avoid precipitation at room temperature. Constant stress creep tests were conducted; the load was applied 75 min after heating of the specimens to test temperature had begun. EXPERIMENTAL RESULTS Creep-Rupture—Fig. 3 shows the log stress-log rupture life plotfor the overaged alloys studied, and also for the underaged A1-2 pct Cu alloy.&apos; At 700°F, the stress-rupture life relationship is nearly independent of both the amount of precipitate (i.e., composition) and of the type of overaging treatment (i.e., precipitate dispersion). At 500°F it is apparent that the increase in rupture life that was ex-

Jan 1, 1960

By I. A. Goddard

INTRODUCTION This paper deals with the development of the sublevel open stoping (SLOS) method in lead orebodies at the Isa Mine of Mount Isa Mines Limited, during the last ten years. Open stoping in different forms has been used at the Isa Mine for many years. Prior to the period under review, stopes were small, pillars were not always recovered, and scrapers extracted the ore. By the end of the sixties, the use of load-haul-dump units was becoming more widespread. Wagner ST5&apos;s were the mucking units for the lead cut and fill stopes. Some of the open stopes in 5 orebody above 13 level had 100 kW slushers, but the more southerly stopes were the sites for the introduction of diesel front-end loaders for extraction. In the early seventies, new methods were used in the block of six stopes in 2 and 5 orebodies between 8 level and 13 level and a trial stoping project was undertaken in 7 orebody between 11 level and 13 level to determine possible stope dimensions for the extraction of the Racecourse orebodies below 13 level. By the mid-19701s, stoping was well underway in 5, 7 and 8 orebodies between 13 level and 15 level, using the &apos;triplet&apos; system, incorporating cemented hydraulic fill to allow greater pillar recovery. As the eighties were entered, development of the Racecourse orebodies below 15 level commenced, as did preparations for 1 orebody in the upper levels of the north end of the mine. In both cases, the pillar recovery method has been changed to reduce the amount of cemented fill required for pillar recovery. GEOLOGY Most of the lead orebodies at Isa Mine lie chiefly to the north of the central shaft complex. They are bedded sulphide deposits in a host rock called Urquhart Shale, which dips at roughly 650 to the west. The main minerals are galena and sphalerite, with the silver mineral, freibergite, being contained in the galena. To the hangingwall of the sequence are the Black Star orebodies (1, 2 and 5) which are relatively wide, pyritic and with low to above average grade lead. The Racecourse orebodies (6 to 16) lie to the footwall, and have a large variation in width, low to high grade lead, and gradation in the lead to zinc ratio from north to south. Stope outlines are often determined by economic or engineering considerations rather than geological. The published extraction reserves are 56 million tonnes of primary ore, containing 150 grams of silver per tonne, 6.4% lead and 6.5% zinc. Traditionally, it has been regarded as lead ore, although the dominant revenue earner varies from time to time. In the Black Star orebodies, the ore and hangingwalls are more competent and open stoping has long been used. The major Racecourse orebodies which have been open stoped are 7 and 8 orebodies. This has been where the orebodies are wider (to the south) and where hangingwall conditions allow. This latter aspect has been greatly influenced by the presence of &apos;silica dolomite1. This tough, relatively homogeneous, non-bedded rock is, in fact, the host rock for the copper mineralisation at Mount Isa, and provides a competent hangingwall for some of the lead stopes. While the shale&apos;s bedding and jointing has a major influence on the ground conditions, there is a major fault system which causes local problems. The principal virgin stress direction is perpendicular to the bedding, but the local stress situation is complicated because of shielding by filled stopes in the hangingwall copper orebodies and because of the interaction between orebodies being extracted to the footwall. Most development on strike is mined with a &apos;shanty-back’, with the back being as close to normal to the bedding as possible. This is near parallel to most jointing and the principal stress direction. Figure 1 is a plan view of 14 level north, which provides a representative horizontal section through the orebodies. A typical cross section is shown in Figure 2. The narrow, parallel footwall orebodies can be seen to differ from the wider hangingwall orebodies.

Jan 1, 1981

By V. B. Kurfman

The temperature, strain rate, and orientation deDendence of defbrnzation of single-crystal MgAg has been examined. The crystals exhibit a tendency to single glide and little or no hardening at 25°C for many orientations. A much higher hardening rate is observed when multiple glide occurs, such as can be initiated by surface defects. The tendency for easy glide becomes less dependent on surface preparation and orientation as T — 100°C and bars so tested often fail after one-dimensional necking-. At T > 200°C (transition temperature for single-crystal notch sensitivity and poly crystalline ductility) single glide diminishes and two-dirnensionul necking begins. The crystals do not strictly obey a critical resolved shear stress law, but show the influence of {loo) cracks in determining the slip mode. The results are correlated with the difficulty of sciperdzslocation intersection and semibrittle behavior of this compound in single-crystal and poly crystalline form. Comparisons are made with the slip selection mode observed in tungsten, with the reported observations of easy glide in bee metals. and with the mechanical behavior of poly crystalline MgAg. PREVIOUS work on tensile deformation of polycrys-talline MgAgl and bending deformation of single-crystal MgAg2 has shown that the compound is semi-brittle (i.e., notch and grain boundary brittle). If this semibrittleness is supposed to result from the difficulty of multiple glide (associated with the problems of superdislocation intersection) one might expect single crystals deformed in tension to show pronounced single glide and strong orientation dependence of hardening rate. These experiments were done to examine this supposition and to study the tensile deformation of a highly ordered system which may be considered bcc if the difference between the two kinds of atoms is ignored (actual structure: CsC1). EXPERIMENTAL Single-crystal ingots were grown by directional freezing as previously described.&apos; These ingots were sliced into a by a by 2 in, rectangular bars by electric discharge machining, then round tensile bars were conventionally machined to 1/8-in.-diam by 1-in.-long reduced section. The bars were typically tested without an anneal because of the problem of magnesium vapor loss and they were typically tested as mechanically polished. The analyses are within the same limits as those reported earlier; i.e., the average composition for each specimen is within 0.5 at. pct of stoichiometry, while the total range from end to end in a given specimen varies from 0.7 to 1.4 at, pct. There has been no indication in the results of any variation in slip or fracture mode attributable to the composition fluctuations. The slip systems were determined by two-surface analysis of the bars after testing to failure at room temperature. Single glide was so dominant that there was little difficulty in identification of the dominant slip system even though the tensile elongation to failure often approached 7 to 8 pct in room-tempera- ture tests. Elevated-temperature testing was done in a silicone oil bath and low-temperature testing was done in liquid Np or a dry-ice bath. All stress measurements are reported as engineering stress unless otherwise specified, and crosshead travel is used as the strain measurement. RESULTS The tendency toward single glide is best seen in the pictures, Figs. 1, 2, and 3, which depict deformation at fracture as a function of test temperature. While it is possible to find regions of secondary slip by careful microscopy, such regions are very small. The development of a ribbon-shaped configuration from an initially round section bar pulled at 100°C is typical, occurred by single glide, and illustrates the degree to which such glide continues. At temperatures =100°C the bars typically show elongation of 20 to 50 pct by predominently single glide. Despite the large elongation, fracture even at 150°C occurs in a brittle mode, Fig. 2, in the sense that it is an abrupt failure which shows no discernible necking in the second dimension of the bar&apos;s cross section (i.e., there is no appreciable action of any slip modes which would decrease the broad dimension of the cross section). Near 200°C the fracture mode changes slightly. Although most of the sample extension is by single glide, after the bar develops the characteristic ribbon shape it begins to neck in the second (i.e., broad) cross-sectional dimension. The bar becomes very thin in the "necked down" region, Fig. 3, and the reduction in area approaches 100 pct. Often there oc-

Jan 1, 1967

By J. R. Cahoon, H. W. Paxton

The possibility of using unidirectionally solidified, two-phase alloys as an approximation to fiber composite materials is investigated. The short-term me.chanical properties and failure modes of unidirectionully solidified A1 (rich)-Cu alloys containing ap -Proximately 0, 17.5, and 27.7 vol pct of 0 phase &apos;fibers" are determined at temperatures from 25" to 500" and compared with those obtained for conventionul SAP alloys. In a previous publication,&apos; hereafter referred to as I, the possibility of understanding some of the room-temperature mechanical properties of unidirectionally solidified castings was explored. For Al(rich)-Cu and Al(rich)-Mg two-phase alloys over a substantial range of compositions, the yield and ultimate strengths and common ductility measures were very adequately predicted from the principles of fiber strengthening4 and the analysis of ductility outlined by Gurland and Plateau." The results obtained in I suggest the possibility of using unidirectionally solidified, two-phase alloys to simulate fiber composite materials where the inter-dendritic second phase or constituent acts as the reinforcing material. Recent attempts concerning the fabrication of fiber conlposites have concentrated on producing composites with a good bond between fiber and matrix and with very long fibers so that their maximum contribution to the strength of the composite may be realized. However, these objectives are difficult to attain in practice and present fabrication processes are either extremely laborious or costly.13 The slow, unidirectional solidification of eutectics has received considerable attention as a method for producing composite materials. 5,6 This method can fulfill both of the above objectives but it is currently laborious, expensive, and has the additional disadvantage that the volume fraction of reinforcing phase cannot be easily varied. On the other hand, unidirectionally solidified, two-phase alloys, also with a good bond between the phases, are relatively easy to make and the volume fraction of reinforcing "fibers" can be easily varied by changing the average composition of the alloy. The disadvantage of the cast alloys is that the mechanical effectiveness of the "elongated interdendritic reinforcements" (EIR)* may be reduced due to their rela- tively short lengths, the w factor in Eq. [2] of I. However, if the EIR have a high strength their contribution can be considerable. For composite materials containing discontinuous cylindrical fibers of various lengths the ultimate strength is given by1 where it is assumed that the composite fractures when the fibers fail. In Eq. [I], a, is the stress in the matrix just prior to failure of the composite, Vf is the total volume fraction of fiber reinforcing constituent, Vf(l+) is the volume fraction of fibers whose lengths exceed the critical length, I,, which is defined as the shortest length of fiber in which the stress can build up sufficiently to break the fiber. af is the fracture strength of the fiber material, w is a factor accounting for the discontinuity of those fibers whose lengths exceed I,, 1-/d is the average aspect ratio of those fibers whose lengths are shorter than I,, and t is the shear stress in the matrix at the fiber-matrix interface. The factor w is dependent on the length of the fibers and also on whether deformation of the matrix occurs plastically or elastically. However, for a given length of fiber, w is smaller when elastic deformation of the matrix is assumed.&apos; It is of interest to consider the properties of simple unidirectionally solidified, two-phase alloys at elevated temperatures in view of the possibility of using suitable modifications for high temperature service. Knowledge of the creep behavior of these materials is still rudimentary (although under active investigation) and the present paper concerns itself with short time tensile properties of some alloys similar to those investigated in I (i.e., unidirectionally solidified Al(rich)-Cu alloys). Unidirectionally solidified alloys containing 5.6, 17, and 23 wt pct Cu were tested parallel to the direction of solidification at temperatures from 25" to 500°C. In the present investigation, the alloys were homogenized for 2 days at 535°C giving a matrix of homogeneous a phase (5.2 wt pct Cu) and an interdendritic constituent (EIR) which was completely Q phase (53 wt pct Cu). EXPERIMENTAL Alloys of nominal composition 5.6, 17, and 23 wt pct Cu (containing approximately 0, 17.5, and 27.7 vol pct 8 phase, respectively, after homogenization at 535°C) were prepared by melting 1200 g of A1 (99.99 pct) in a high purity graphite crucible and adding the appropriate amount of freshly cleaned copper chips (99.9 pct). The molten alloy (at 700°C) was poured into a preheated graphite mold (also at 700°C) and the ingot unidirectionally solidified by impinging water on the steel baseplate of the mold. The alloy was degassed immediately

Jan 1, 1970

By AIME AIME

THE luncheon of the Milling Methods Committee in the Engineers&apos; Club, on Feb. 16, was distinctly a social affair, although several matters of a non-milling nature were fruitfully discussed. The session* on Milling Methods, the same afternoon, attracted a gathering which overtaxed the capacity of the Board Room on the fifteenth floor. Galen H. Clevenger presided, with the moral reinforcement of Charles Butters. As all papers were available in printed form, and since synopses have appeared in MINING & METALLURGY, it is unnecessary to cover the contents of each in detail here. The first paper (T. P. 410), by Leaver and Woolf, on the "Flotation of Minor Gold in Large-scale Copper "Concentrators," was excellently summarized by R. S. Dean of the U. S. Bureau of Mines, who stressed the -very definite action of lime as a depressant of gold, and showed how the authors had worked out the best conditions of alkalinity, pH concentration and reagents for -optimum recovery of gold along with base metals, especially where lime had to be used to depress pyrite. No discussion was evoked.

Jan 1, 1931

By Yoichi Ishida, Ching-Yao Cheng, John E. Dorn

Tile creep behavior of a iron was investigated over the range of temperatures from 375° to 1150°K. Apparent activation energies for creep, obtained by the effect of sudden changes in temperature on the creep rate, revealed the presence of- four distinguishable regions. The creep behavior of a iron in Regions II (480° to 774°K) and 111 (775° to 1045°K) was found to correlate well with a model where the creep rate is controlled by the nonconsevualive motion. of jogged screw dislocations. An anomalous increase in the apparent activation energy fur creep in Region III was found to be in harmony with the known decrease in the free activation energy for self-diffusion over the Curie transformation range. Furthermore, the creep rates in Regions II and III were found to increase with stress due not only to the effect of stress on the activation energy but also to an increase in density of mobile dislocations. The evidence suggests that pipe diffusion along moving dislocations could be a significant factor over the lower temperatures of Region II. ALTHOUGH the creep properties of iron and steel have been of interest to metallurgists for some time and an extensive literature is now available, most of the published information has not produced much toward understanding the fundamental dislocation processes controlling the creep behavior of these materials. Whereas the activation energy for high-temperature creep of metals usually agrees well with that for self-diffusion, Sherby, Orr, and Dorn1 deduced from the data of Tapsell -and c1enshaw2 that the activation energy for creep of Armco iron is about 78,000 cal per mole and more recently Lytton and sherby3 reviewed the data of Jenkins and Mellor4 and found an activation energy for creep of a iron of 80,000 cal per mole. Both values are substantially greater than the activation energy for self-diffusion in a iron. Because of the limited data suitable for purposes of identifying the controlling dislocation mechanisms of creep and the unusually high activation energies for creep quoted above, it was considered desirable to reinvestigate in detail the creep of a iron by more reliable techniques which would provide sufficient data for determination of the creep mechanisms. EXPERIMENTAL TECHNIQUE Creep specimens were prepared from 3/8 by 4 in. iron bar stock of the following composition by weight percent: 0.001 C, 0.0120 0, 0.001 N, 0.004 S, and 0.003 P. The as-received bars were cold-rolled to a thickness of 0.100 in., annealed under argon for 30 min at 1113°K, cold-rolled to a final thickness of 0.063 in., and machined into tensile specimens having gage section 0.250 in. wide and 1.70 in. long. Finally they were recrystallized under argon at 1113°K. Specimens to be crept above 1060°K were recrystallized at 1173°K. Both recrystallization treatments gave the same reproducible equiaxed ASTM No. 4 grain size. Creep testing was conducted in machines fitted with Andrade-Chalmers arms that maintained a constant stress to within ±0.2 pct of the reported values. Deformation over the specimen gage section was sensed with a linear differential transformer and recorded auto-graphically as a function of time. The strains deduced from these measurements were sensitive to ±5 x 10-5. During creep the specimens were contained in an argon-filled chamber which was immersed in a temperature-controlled molten tin bath. Creep temperatures, as measured by thermocouples attached to the specimen, were maintained to within ±10.25°K of the reported values. For activation-energy determinations rapid changes in temperature of about 12°K were obtained within 30 sec by direct resistance heating of the creep specimen, and maintained to ±1°K of the reported values. Observations of structural details of specimens before and after creep tests were made by electrolytic polishing and etching in acqueous ammonium persulfate. EXPERIMENTAL RESULTS A typical example of the determination of apparent activation energies, Q, by the effect of small changes in temperature is illustrated in Fig. 1. Q is defined by

Jan 1, 1967

By I. Javandel, P. A. Witherspoon

The finite element method was originally developed in the aircraft industry to handle problems of stress distribution in complex airframe configurations. This paper describes how the method can be extended to problems of transient flow in porous media. In this approach, the continuum is replaced by a system of finite elements. By employing the variational principle, one can obtain time dependent solutions for the potential at every point in the system by minimizing a potential energy functional. The theory of the method is reviewed. To demonstrate its validity, nonsteady-state results obtained by the finite clement method are compared with those of typical boundary value problems for which rigorous analytical solutions are available. To demonstrate the power of this approach, solutions for the more complex problem of transient flow in layered systems with crossflow are also presented. The generality of this approach with respect to arbitrary boundary conditions and changes in rock properties provides a new method of handling problems of fluid flow in complex systems. INTRODUCTION Problems of transient flow in porous media often can be handled by the methods of analytical mathematics as long as the geometry or properties of the flow system do not become too complex. When the analytical approach becomes intractable, it is customary to resort to numerical methods, and a great variety of problems have been handled in this manner. One such method relies on the finite difference approach wherein the system is divided into a network of elements, and a finite difference equation for the flow into and out of each element is developed. The solution of the resulting set of equations usually requires a high speed computer. When heterogeneous systems of arbitrary geometry must be considered, however, this approach is sometimes difficult to apply and may require large amounts of computer time. The finite element method is a new approach that avoids these difficulties. It was developed originally in the aircraft industry to provide a refined solution for stress distributions in extremely complex airframe configurations. 27 Clough has recently reviewed the application of the finite element method in the field of structural mechanics.6 The technique has been applied successfully in the stress analysis of many complex structures.l, 27, 28 Recognition that this procedure can be interpreted in terms of variational procedures involving minimizing a potential energy functional7 leads naturally to its extension to other boundary value problems. In the field of heat flow, there recently have been introduced several approximate methods of solution that are based on variational principles.2-4, 17 By employing the variational principle in conjunction with the finite element idealization, a powerful solution technique is now available for determining the potential distribution within complex bodies of arbitrary geometry. In the finite element approximation of solids, the continuum is replaced by a system of elements. An approximate solution for the potential field within each element is assumed, and flux equilibrium equations are developed at a discrete number of points within the network of finite elements. For the case of steady-state heat flow, the technique is completely described by Zienkiewicz and Cheung.33 Since the flow of fluids in porous media is analogous to the flow of heat, Zienkiewicz et al. have employed the finite element method in obtaining steady-state solutions to heterogeneous and anisotropic seepage problems. 34 Taylor and Brown have used this method to investigate steady-state flow problems involving a free surface.25 The work of Gurtin has been instrumental in laying the groundwork for the application of finite element methods to linear initial-value problems.12 As a result, Wilson and Nickell have recently

Jan 1, 1969

By C. Gatlin, M. E. Chenevert

The effects of bedding plane orientation on the elastic constants and the yield strengths of three laminated rocks (one sandstone and two shales) and one isotropic rock (a limestone) were studied. The directional dependence of the elastic properties of these rocks was experimentally evaluated using a triaxial compression cell and auxiliary stress-strain measuring equipment. Symmetry of Poisson&apos;s ratios within the bedding plane suggested that horizontal isotropy exists, but the bedding planes do give rise to an appreciable difference between properties in the horizontal and vertical directions. For the three bedded rocks studied, Young&apos;s modulus was lower normal to bedding than along bedding. Yield strengths were determined at confining pressures from 0 to 12,000 psi in a triaxial compression cell. The rocks studied showed strength reductions as high as 40 per cent when the test specimen was oriented at 20°-30° to the bedding planes. The mechanical behavior of these rocks suggested that the rock properties of shear strength and/or coefficient of internal friction can vary with direction, depending on the particular rock tested. Tensile strengths were also measured and found to be lowest when failure occurred along bedding. This work shows that bedded formations exhibit sizable directional variations in both their elastic constants and yield strengths. It is suggested that these variations may be accounted for by using the "elastic laminate" model and the "variable coefficients" failure model. INTRODUCTION The nature of rock deformation at elevated pressures has been studied by many workers; papers by Handin,l,2 and Robinson3 illustrate the present state of knowledge. Most investigators have either chosen rocks which were as isotropic as possible (in order to avoid complications of data interpretation and analysis) or they have oriented their samples so that the effects of anisotropies (such as bedding planes) have been avoided. Of the studies performed, few were concerned specifically with mechanical anisotrop-ies. Griggs4 has presented limited data for specimens cut parallel, normal, and 45° to the bedding plane; he relates the strength anisotropy observed to the fabric (bedding) anisotropy. His tests were primarily concerned with large deformations (20 per cent strain); thus, no directional values of the elastic constants were reported. Handin has reported the results of similar experiments. Bott5has discussed rock strength anisotropies due to faults, cleavage, or bedding. He was concerned primari ly with determining the shear stress on such planes and did not mention the effect of friction. Jaeger6 later generalized Bott&apos;s work by taking friction into account and presented a limited theory for the failure of rocks having a "single plane of weakness", and also for rocks having a constant coefficient of friction, and a shear strength which varies with bedding plane orientation. Donath and Cohen,7 and Donathg have evaluated rock strengths from shale and slate specimens cut normal and parallel to bedding. A dependence of cohesive strength (7,) on the specimen orientation was also shown. Adler9 has also studied this problem and lists similar results. He assumes that all bedded rocks behave according to Jaeger&apos;s single-plane-of-weakness theory. Kalinin and Belorussov10 list results for strength tests parallel and perpendicular to bedding and use this information as a basis for hole deviation analysis. From the literature it is apparent that sedimentary rocks have been tested under widely varying conditions of stress; however, the assumption of isotropy is generally, but not always, made. Since geologic sedimentation often deposits sediments in very definite lavers.,. it seems that more svstema tic attention should be given to the possible effects of this natural bedding. Bedding, as used here, refers to visible regularities of grain size or orientation resulting from depositional processes. The mechanical strength anisotropies, which bedding may present, is not the only anisotronic property to be considered, since the elastic

Jan 1, 1966