Search Documents

By R. F. Mehl, C. E. Birchenall

SINCE Maxwell1 first considered the self-diffusion process in 1872 its importance in the kinetic theory of matter has been recognized. Until the discovery of isotopes in 1913, a direct measurement of this quantity seemed impossible. The only information that could be gathered indirectly was for gaseous systems for which the kinetic theory was well developed. When methods of direct observation be-came available, investigations on self-diffusion were carried out in condensed phases. In metals these data are presumably of potential importance in the study of recovery, recrystallization, creep, sintering, and related phenomena. Following the pioneer work of Von Hevesy2 and his collaborators, who determined the rate of self-diffusion in lead with the naturally occurring thorium B isotope, several metals have been investigated. Pb, Ag³, Au.6,5, and Cu6,7,8,9 are examples of isotropic crystals existing in only one phase modification. Anisotropy of diffusion has been demonstrated in Bil6 and Znll. This paper is a study of a single metal in two allotropic forms and also of self-diffusion in a body-centered cubic lattice. Despite the fact that the measurements in each of the papers cited on self-diffusion in copper seem to be internally consistent to about 10 to 15 pet, the curves reported by different authors differ by factors of 2 to 4 at the same temperatures. This uncertainty may account, in part, for the failure to establish a successful correlation between the self-diffusion rates and other physical characteristics of the metals. No satisfactory theory of metallic self- diffusion has as yet been proposed to account for all the existing data and to permit estimation in other metals. Experimental Part: Two units of radioactive iron were used in these experiments, each a mixture of Fe53 and Fe59 (12). Fe53 decays by K electron capture and the emission of an X ray with a half life of about 4 years. Fe59 emits two beta spectra, one with a maximum energy of 0.26 Mev, the other 0.46 Mev, and gamma rays of 1.1 and 1.3 Mev, with a half life of about 44 days. They were present in nearly equal concentration initially. The composite half life started at about 50 days and increased as the Fe59 decayed, leaving Fe55 relatively more abundant. After aging a year, the half life was too long to measure significant decay in a month. The absorption properties also changed with time. Because of the importance of the absorption coefficient in the diffusion calculations, it was necessary to determine this quantity frequently over the period during which these experiments were carried out. This correction was unsuspected at the time of publication of notesl3 on this work and accounts for the discrepancy in alpha iron and for part of the discrepancy in gamma iron.* * The data in the present paper supersede those given in the notes entirely. In one note the scale of log D was inadvertently reversed. In addition to the correction for the drift in absorption coefficient, the D values for gamma iron at low temperatures were high owing to insuficient correction for diffusion occurring during heating and cooling through the high temperature part of the alpha range at a rate much slower than that employed in the runs reported here. The high temperature alpha rates are much higher than the low temperature gamma rates and correspond to large equivalent times at these temperatures. These experiments were discarded and new measurements taken. Independent experiments with the same activity units indicated a radioactive contaminant in the iron, but exhaustive attempts to isolate and identify it chemically failed. These experiments? indicate † These experiments will be discussed in a later publication from this laboratory. that the contaminant represented only a trace of little importance in the diffusion results. The active iron was plated from an iron chloride solution. Enough of the solution was dropped on a 1% in. square of filter paper to wet it thoroughly.

Jan 1, 1951

By J. G. Savins

Certain types of macromolecules added to water and salt solutions flowing in turbulent motion can reduce the pressure gradient. Alternatively, the volumetric capacity of a pipe for these fluids is increased by the presence of these materials. Examples presented show that the drag reduction can become significant. Thus, the presence of 0.28 per cent of a gum derivative in a solution of sodium chloride flowing at 200 gal/min in a 1.89-in. pipe yields a pressure drop which is 0.44 of the single-phase drop measured under the same conditions of turbulent flow; the addition of 0.1 per cent of a vinyl derivative to a I-in. water line yields a throughput capacity which is 1.78 of the single-phase capacity at the same pressure drop. It is further shown that these phenomena are distinctly different from previous observations with other classes of non-Newtonian systems. There a simple lowering of friction factors below the levels predicted from the resistance laws for Newtonian fluids is associated with a suppression of turbulent motion. A rational physical explanation for drag reduction is advanced. Briefly, the proposed mechanism is a storage by the molecular elastic elements of the macromolecules in solution of the kinetic energy of the turbulent motion. INTRODUCTION This study was inspired by a recent review of some paradoxical drag reduction phenomena in turbulent pipe f1ow.I Under very moderate conditions of turbulent flow, the pressure gradient necessary to pump solutions containing certain specific kinds of polymers, fibers and metallic soaps may become appreciably lower than that required* to pump the solvent, i.e., water or a low-viscosity hydrocarbon, under identical flow rates in the same conduit. As shown by our review, this phenomenon of drag reduction in turbulent duct flow was first noted during the second world war, apparently arising in connection with the development of flame warfare weapons. Since that time several papers illustrating this phenomenon have appeared: Toms, Oldroyd,3 Agoston et al., Bundrant and Matthews, Robertson and Mason,6 Ousterhout and Hall,7 Daily and Bugliarello~ Lummus, Anderson, and Fox. 9 That there are practical applications for techniques which increase discharge or decrease the pressure necessary to transport a liquid through a pipeline is illustrated in the patents which have issued which take advantage of this peculiar phenomenon, e.g., Mysels,l0 Dever, Harbour, and Seifert.11 One also finds fragmentary evidence of this effect in the data pertaining to a few of the polymeric solutions studied by Shaver12 and Dodge.13 However, these investigators were concerned with the development of friction factor vs Reynolds number correlations for a variety of non-Newtonian solutions and suspensions, rather than in a study of drag reduction-. A similar kind of drag reduction effect has been observed in gases. Sproull, for example, reports that adding dust to air flowing in turbulent motion through a pipe results in a lowering of the pressure gradient at identical flow rates. There are also military applications for reducing the drag on hydrodynamic vehicles. For example, the possibility of injecting a rheologically complex fluid into the boundary layers of bodies to reduce the skin friction has been investigated by Fabulal5 and Granville.16 Along somewhat different lines are the drag reduction studies of Kramer.17118 He has shown that skin friction can be reduced by covering the surface of a vehicle with a flexible skin. The effect is apparently due to the boundary layer being stabilized by the presence of the skin. Drag reduction by means of coexisting gas and liquid boundary layers, e.g., film boiling and continuous gas injection, has been proposed by Bradfield, Barkdoll, and Byrne,19 Cess and Sparrow,20'21 Sparrow, Jonsson, and Eckert.22 Here the skin friction occurs between a vapor and a surface rather than between a liquid and a surface. There are several references in the literature to friction-factor correlations for non-Newtonian solutions and suspensions: Shaver and Merri11,23 Dodge and Metzner, Clapp,25 and Thomas.26

Jan 1, 1965

By C. S. Finney, John Mitchell

The introduction of ovens for the production of metallurgical coke is believed to be due to L. L. Norton who operated an iron foundry in the vicinity of Connellsville, Pa. Persuaded by his foreman, an English immigrant named Nickols from Durham, L. L. Norton put up a 12-ft square oven which produced coke in 1833. The coal used was taken from a local mine at Mounts Creek. The oven seems to have been used in conjunction with the customary method of coking in mounds. It was in the Connellsville district also, in 1841, that two carpenters, Provence McCormick and James Campbell, formed a partnership with John Taylor, a stone mason, for the manufacture and sale of oven coke. The task of the mason was to construct the ovens, while the carpenters were to build the arks by which the coke could be taken by water to the market at Cincinnati. The following account of the enterprise was given by McCormick: "James Campbell and myself heard in some way that I do not now recollect that the manufacturing of coke might be made a good business. Mr. John Taylor, a stone mason, who owned the farm on which the Fayette coke works now stand, and who was mining coal in a small way, was spoken to regarding our enterprise, and proposed a partnership-he to build the ovens and make the coke and Mr. Campbell and myself to build a boat and take the coke to Cincinnati, where we heard there was a good demand. This was in 1841. Mr. Taylor built two ovens. I think they were about 10 feet in diameter. My recollection is that the charge was 80 bushels. The ovens were built in the same style as those now used, but had no iron ring at the top to prevent the brick from falling in when filling the oven with coal, nor had we any iron frames at the mouth where the coke was drawn. The top and mouth had to be repaired when they fell in. In the spring of 1842 enough coke had been made to fill two boats 90 feet long-about 800 bushels each-and we took them to Cincinnati down the Youghiogheny, Monongahela, and Ohio, but when we got there we could not sell. Mr. Campbell, who went with the boats, lay at the landing some two or three weeks, retailing out one boatload and part of the other in small lots at about 8 cents a bushel. Miles Greenwood, a foundryman of that city, offered to take the balance if he would take a small patent flour mill at $125.00 hi pay, which Mr. Campbell did. He had it shipped here. We tried it, but it was no good, and we sold it to a man in the mountains for $30.00, and thus ended our coke business." So successful did the coke subsequently prove to be in use that the three partners were asked to deliver more. Evidently they had had enough of the coke business, however, for they refused to have anything more to do with it. Few ovens were built between 1841 and 1855, and it is reported that in the latter year, "there were only 26 coke ovens along the river above Pittsburgh". Successful coke makers of these years included Mordecai Cochran, Richard Brookius, and Colonel A. M. Hill. It was the use of coke in 1859 in the Clinton furnace erected by Graff, Bennett and Co. in a plant on West Carson Street, Pittsburgh, that brought the real beginning of the coke-iron era in America. Here the successful use of Connellsville coke as a blast-furnace fuel was demonstrated beyond all possible doubt, and from the year 1859 the coking industry expanded tremendously. The era of beehive coke ovens During the latter half of the nineteenth century and the early years of the twentieth, the major percentage of metallurgical coke produced in the United States came from beehive ovens. It was not until 1893 that the first battery of by-product ovens came

Jan 1, 1961

By L. S. Allen, R. L. Caldwell, W. R. Mills

Borehole models used in the study of nuclear well logging are reviewed and the merit of heterogeneous us homogeneous formation simulation is discussed. .A heterogeneous model for simulating sandstone formations of variable porosity is described. Simulation adequacy was checked by steady-state and pulsed-neutron measurements. INTRODUCTION In the course of developing new methods of nuclear well logging, the problem of testing new logging instruments under controlled conditions always arises. This testing is usually done in wells of known lithology, porosity and fluid saturation, or in laboratory test facilities which simulate the borehole environment. Although the former approach is possibly more satisfying, it is frequently difficult or inconvenient to find wells with enough variation in the cited parameters for a truly comprehensive study, On the other hand. laboratow- test facilities can simulate a wide variety of formation and borehole conditions if care is exercised to maintain adequate simulation under all conditions. Workers concerned with the development of nuclear well logging methods have reported several types of research facilities in the past. Tittle, et a1 used cubical tanks filled with Ottawa silica sand to study the steady-state behavior of thermal and epithemal neutrons in simulated sandstone logging environments.1 In addition to the effects of fresh vs salt water, a wide variety of casing sizes and compositions were investigated. Tittman also used a large tank of Ottawa sand to measure the slowing down length of sio2;2 for making the same measurement in CaCO3, however, an assembly of solid Vermont marble blocks was used. More recently a very useful and carefully planned test pit for nuclear logs was constructed under the auspices of the API.3 This facility consists of three massive limestone sections, each 6-ft thick and more than 5 ft in diameter. The blocks are buried, one on top of the other, in a concrete- lined pit having a total depth of 24 ft. Each section is made of a different limestone to achieve porosity variation, the selection being Carthage (2 per cent), Indiana (19 per cent) and Austin (26 per cent). The blocks are traversed by a 7 7/8-in. diameter borehole and are saturated with fresh water. Great care was taken to insure total saturation of the stone. Homogeneous mixtures and materials have not been used exclusively for simulating earth formations. Tittle, et a1 4 showed that a heterogeneous lattice of water and graphite could be used to simulate Liquid furfural with very little effecton measured thermal and epi thermal neutron distributions. Subsequently, a lattice-type model for simulating limestone earth formations was designed and built by Berry This limestone model was constructed of 7/8- x 11/4- x 36411. marble rods glued together with a plastic resin to form a 36-x 42- x 42in. cube. The cube was honeycombed vertically with 7/8- x 7/8- x 3641-1. holes for porosity and had a 111/2-in. diameter hole in the center to serve as the borehole. Lower porosities were simulated by placing marble rods in the square holes. The finished cube was used with the borehole vertical and set in a tank to hold liquid for filling the holes in the rock matrix. A second type of heterogeneous borehole model has been proposed by Kukharenko, et a1.6= In this concept the model is composed entirely of solid material. The hydrogen equivalent of formation fluids is simulated by making the model of alternating layers of dense rock and celluloid. Additional hydrogen is included by drilling vertical holes in the rock sections and filling them with solid forms of hydrogeneous material. The volume of the holes is equal to the volume of the celluloid layers, so an axial and radial dispersion of the hydrogeneous material is thus obtained. One such model was composed of alternate 50 mm-thick sand layers and 2 mm-thick celluloid sheets. Approximately 200 appropriately spaced plastic tubes were used in each sand section. The plastic tubes were filled with paraffin for additional hydrogen concentration. This arrangement yielded a model with a water-equivalent hydrogen concentration of 10 per cent. Experimental data taken in this model and in a model consisting of the same material but homogeneously dispersed showed that the heterogeneous system adequately

Jan 1, 1966

By D. M. James, J. C. Martin

The results are presented of a study of the application of analytical methods to the solution of two-phase flow into single wells. Approximate analytical expressions for the pressure distribution in two-phase flow are found ;;; a number of conditions. The results obtained from the analytical solutions me found to be in good agreement with results obtained by finite difference techniques using a high speed digital computer. Mathematical solutions for four sets of boundary conditions are presented. All of these solutions are composed of a short-term transient plus a steady or quasi-steady state. The rates of decay of the short-lived transients are analyzed. It is found that the durations of the short-term transients may be characterized by a parameter defined as the time constant which can be determined from simple relations. It is shown also that if the outer radius is much greater than the radius of the well. the short term transients decay at rates which are proportional to the square of the exterior radius, and the rates of decay are only slightly dependent upon the radius ratio. Numerical solutions based on finite difference techniques are presented for a number of conditions. The numerical solutions are in good agreement with the predictions based on the theoretical analysis for small and moderate drawdowns. Examples involving large drawdowns indicate that the nonlinearities in the equations of flow do not appreciably alter the longevity of the short-term transients. In all cases the time required for the short-tern transients to disappear is predicted satisfactorily. INTRODUCTION The mechanism by which oil and gas flow into a single well is of vital interest to the petroleum industry. The fundamental equations of two-phase flow which describe this mechanism are nonlinear partial differential equations. Numerical solutions of these equations describing pressure transients have been obtained with the aid of electronic computers. Although solutions obtained in this manner take into account a large number of effects, the reduction of this information to useful generalities is difficult. One method of obtaining generalities is the use of linearized approximations of the nonlinear equations. Since it is possible to obtain explicit solutions of the linearized equation, general properties of the role of pressure in the flow mechanism may be ascertained. Results obtained from this approach are limited to some extent by the linearizing assumptions. The severity of these limitations may be evaluated by comparing solutions of the linear equation with numerical solutions of the more exact nonlinear equations of two-phase flow. In the past considerable amount of work has been devoted to studying pressure build-up using the single-phase flow theory. Unfortunate1y, most prep sure build-up tests involve multiphase flow. A small amount of work has been done studying pressure build-up where the flow is two-phase. The encouraging results of these studies suggest that useful results may be found from additional studies of not only pressure build-up, but also the rapid transients associated with placing a well on production. This paper presents the basic theory of the pressure transients associated with placing a well on production and with closing it in. The paper is concerned chiefly with two-phase compressible flow; however, the results also apply to single-phase flow. The results are based on analytical solutions of the flow equations, and they are verified by numerical solutions using finite difference techniques. Much of the previous work on compressible flow into wells has been confined to single-phase flow. Some work has been done on compressible two-phase steady state flow, and solutions of the equations of flow have been found by finite difference techniques using high-speed computers. Muskat1 presents some rather general solutions to the equations of single-phase compressible flow into wells. Much work has been done on pressure build-up in wells (see, for example, Refs. 2-6). Almost all of the work on pressure build-up concerns single-phase flow with the exception of Ref. 5 and part of Ref. 2. Some work has been done on pressure fall-off in injection wells.718 Muskat9 presents the solution of the equations for radial steady state two-phase compressible flow. Handyl0 extends Muskat's solution to obtain

By M. A. Grossmann

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a ''pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain sue may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of un- hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybde- num when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as wouldappear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added " 20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost lo per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome- molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By George Krauss, M. Cohen

The reverse martensitic transfomzation (i.e., the conversion of martensite to austenite on heating) was investigated in Fe-Ni alloys containing 30.5 to 33.5 wt pct Ni. The reversed austenite was found to be sufficiently distorted to exhibit marked differences in mechanical properties and to undergo recovery and re crystallization on further heating. In particular, the yield strength of the reversed austenite was as much as 2.5 times higher than that of the virgin austenite: with five cycles of the direct and reverse martensitic transformation, the yield strength was 2.6 times higher. There was an accompanying decrease in strain-hardening capacity and in stable ductility or uniform elongation. The recrystallization was observed to follow sigmoidal kinetics, but was characterized by an abnormal1y large temperature dependence which was evidently due to carbon segregation at the migrating grain boundaries. Upon recrystallization, the strength Properties reverted to those of the virgin austenite, but the ductility did not fully recover until the annealing temperature was further raised to dissipate the carbon segregation at the grain boundaries. The transformation of reversed austenite to produce second-generation martensite resulted in an unusually imperfect structure, thereby leaditg to additional strengthening. Horlleuer, the martensitic phase was much less responsive in this respect than was the austenite. MOST martensitic transformations are capable of undergoing a reverse transformation back to the austenitic phase on heating.&apos; This reaction, like the direct transformation to martensite on cooling, is usually athermal. In analogy with the Ms andMf temperatures for the martensitic transformation (where M, > Mf), the reverse transformation is characterized by the As andAf temperatures (where As<Af). It is well-known that the finish (Af) of the martensite-to-austenite reaction on heating may occur at a temperature where austenite is not stable relative to other phases in the equilibrium diagram.&apos; Reverse martensitic transformations have been found to influence the properties of the parent austenitic phase in a number of ferrous alloys. The austenite thus produced after one or more reversals is significantly altered in strength, microstruc-ture, diffusivity, and annealing characteristics compared to well-annealed, virgin austenite. The first detailed observations of such phenomena were made by Wasserman3 on an Fe-30 wt pct alloy. He found that the reversed austenite (i.e., austenite formed by the reverse martensitic transformation) was much stronger than the original austenite, and the second-generation martensite (i.e., martensite produced from the reversed austenite) was somewhat stronger than the first-generation martensite. On heating the reversed austenite, recrystallization occurred in a manner similar to that of a cold-worked metal; the Laue spots sharpened and the strength decreased.4 In recent years, Russian workers have shown considerable interest in these reverse martensitic transformations. Most of such investigations5-10 have been concerned with the stabilization of reversed austenite relative to subsequent martensitic transformation, and because of its unusual nature, this phenomenon will be discussed in detail elsewhere." On the other hand, the annealing behavior of reversed austenite and the attendant variation in properties have received little attention beyond the experiments of Wasserman.3,4 Gridnev eta1.,8 in one of the few such studies. followed the hardness change of reversed austenite as a function of time at three annealing temperatures. The marked strengthening of austenite achieved by the reverse martensitic transformation has been referred to as "transformation strengthening" by Wasserman3,4 and as "phase hardening" by Malyshev et a1.7,9,10 to differentiate it from hardening produced by cold working. Both groups of investigators noted that further strengthening of the austenite could be attained by repeated or cyclic transformations, but the first cycle resulted in the most pronounced effect. Evidence of the altered microstructure of reversed austenite has been reported by Maximova and Nikonorova6 and by Edmonson and KO.12 The former found that reversed austenite was much more sensitive to etching than the original austenite, and the latter authors observed a (&apos;ghost" structure resembling martensite in certain areas of the reversed austenite. Enhancement of the self-diffusion rate in reversed

Jan 1, 1962

By M. A. Grossman

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of unhardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of o.-2o per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as would appear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.2o per cent Mo provides a factor of 1.63, an increase of over 6o per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater harden ability will be obtained by using, for example, o.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By S. A. Levy, J. D. Wood, J. F. Libsch

A study of the preparation and characteristics of a sevies of Fe-C-N alloys has been conducted. X-ray, microhardness, and metallographic data from a series of single-phase alloys produced by controlled nitriding of carburized foils are reported. The existence of a, y&apos;, and E carbonitride has been confirmed and it has been found that y&apos; is the hardest of these three phases. These results have been used to interpret the structures observed in nitrided steels. ThIS paper represents the second phase of a three-part study concerning combined nitriding and induction hardening. The first part&apos; reports the engineering properties (depth hardness, fatigue, corrosion, and tempering resistance) obtained when seven different steels were subjected to the combined surface hardening treatment. The present paper concerns the nature of a series of single-phase alloys prepared by controlled nitriding of carburized foils. The objective was to simulate the various layers present in the as-nitrided steels. A third paper will report data concerning induction hardening of the foils and will attempt to set forth a mechanism for the high hardness obtained with the combined treatment. Studies of nitriding generally fall into three categories. The first were performed with bars using conventional nitriding procedures, thus yielding a nitrogen gradient and a series of phase layers near the surface.2-6 Such studies were complicated by the presence of the nitrogen gradient, for it was difficult to correlate microhardness and X-ray data with chemical composition. There were always complications due to penetration of the X-ray beam which yielded data influenced by underlying layers. Similar difficulty was experienced in taking hardness readings on a tapered specimen or in isolating various layers by machining. A second group of investigations was primarily concerned with establishment of regions in the Fe-N7,9,10 or the Fe-C-N phase diagram.8 These were performed with powder specimens which were nitrided in am-monia-hydrogen mixtures to produce a series of single-phase specimens. Unfortunately, the powder specimens were not amenable to either microstruc-ture or microhardness study. The third was essentially a compromise of the first two. Bose and Hawkes," using 0.005-in.-thick iron foils, were able to obtain microhardness, microstruc-ture, composition, and X-ray data on Fe-N alloys of eutectoid composition by equilibration in ammonia-hydrogen mixtures at 1290°F. To obtain a better understanding of the nitriding process and the characteristics of the phases in ni-trided plain carbon steels, the present investigation was undertaken. The investigation was patterned after that of Bose and Hawkes with the exception that nitriding was performed at 930°F (below the eutectoid temperature), as in the case of conventional nitriding. In addition to gaining some understanding of the source of high hardness of nitrided and induction-hardened steels, found in a previous study,&apos; this investigation was concerned with the possibility of controlling the phases present in a nitrided case through the use of ammonia-hydrogen mixtures. Knowledge of the properties of each phase and the conditions necessary for its production could make it possible to avoid undesirable surface layers in nitriding. EXPERIMENTAL PROCEDURE Specimen Preparation. A specimen thickness of 0.005 in. was selected to insure that a uniform nitrogen concentration could be obtained in a reasonable length of time by equilibration in an ammonia-hydro-gen atmosphere. The starting material was a vacuum-cast ingot of pure iron, the major impurities of which were: C, 0.003 pct; 0, 0.014 pct; S, 0.004 pct; N, 0.003 pct.* &apos;Compositions are quoted as weight percent except as noted. The ingot was heated to 1500°F in a nitrogen atmosphere and forged to a slab 0.25 in. thick. The material was then reduced to 0.005 in. by alternately cold rolling and annealing in a nitrogen atmosphere at 1600°F. This material was divided into five groups of specimens which, after carburizing, yielded the following carbon contents: 0.003, 0.28, 0.36, 0.46, and 0.74 pct C. The carburizing was performed by the Leeds and Northrup Research Laboratories, using a controlled "carburizing potential" which yielded a uniform carbon concentration throughout the cross section.

Jan 1, 1970

By M. Marciano, K. Kreider

Silicon carbide coated boron fiber (Borsic) reinforced aluminum composites were made which exhibit strength and modulus values predicted by the rule of mixtures. A successful technique for fabricating these composites consists of plasma spraying of monolayer filament reinforced tapes and subsequent diffusion bonding of these tapes into composites. The elastic properties of the composites were given by the rule of mixtures in reinforced directions. (The modulus parallel to the fibers was 32 x 106 psi for a composite with 50 pct by volume fibers. The other elastic properties for a composite with 50 pct fiber were transverse modulus = 14 to 16 X 10 psi, G = 9.5 x 106psi, and v,, = 0.23. Tensile strengths of over 190,000 psi were measured for the composites with 50 pct fiber and the average strength for these composites was 162,000 psi. These same composites had interlaminar shear strengths of 12 to 15,000 psi. Multidirectionally reinforced composites demonstrated the same reinforcement efficiency in strength and modulus as the uni-directimlly reinforced composites. Comrpessive strengths of composites with 50 pct by volume fiber were found to be greater than 250,000 psi. STRUCTURAL filamentary composite materials are being considered for use where high strength, high modulus, and lightweight materials are required. Metal matrix composites have been considered for use at temperatures ranging from cryogenic (aluminum stainless steel) to 6000°F (plasma sprayed tungsten plus tungsten fiber) and other requirements have been similarly diverse. Metal matrix composites offer high modulus and high strength in unreinforced directions, the ability to be joined by brazing or welding, and greater fracture toughness compared with the more easily fabricated resin matrix composites. This paper deals with the mechanical properties of aluminum boron composites, a system which is being considered for applications where lightweight, high modulus, and high strength are required at temperatures including those above the normal operating temperatures of resin composites. The boron fiber used in this investigation had an average room temperature strength of greater than 400,000 psi, a modulus of 58 x 106 psi, and a density of 0.09 lb per cu in. (2.6 g per cu cm).&apos; The fiber used in the composites had a coating of silicon carbide to retard degrading reactions with the matrix at elevated temperatures. The coated fiber, which is sold commercially as Borsic: has been reported to have excellent resistance to degradation at temperatures up to 600°C in air and in aluminum2 and the same mechanical properties as the standard bare boron fiber. Fabrication of Composites. The composites were diffusion bonded from plasma sprayed monolayer tapes. These tapes were fabricated on a substrate of aluminum alloy foil which is incorporated in the composite matrix. The technique consists of winding a layer of fiber on the foil, and plasma spraying the balance of the matrix alloy over the windings which bonds all of the components together. Advantages of this process include the ability to achieve good fiber spacing, Fig. 1, the formation of a good bond between fiber and matrix (achieved during the plasma spraying), and the adaptability of the process for forming large and complex parts. This is particularly true when used with brazing foil backing which alloys low pressure bonding of the structural shape. PROPERTY EVALUATION TECHNIQUES Tensile test specimens, 5 to 7 in. long with a reduced gage section and ,030 to ,040 in. thick, were cut from composite sheets with a diamond saw. The gage section was .200 in. wide, while the gripped section was .240 in. wide and over 2 in. long in each grip. The standard gage length used was 1 in., however, transverse specimens (i.e., specimens with the fibers oriented 90 deg to the loading axis) were tested without a reduced section. Twelve specimens were also made with a 3-in. gage length but no significant effect of gage length was measured. The tensile test specimens were mounted in a fixture and aligned in friction grips using a 10X microscope. Unbonded foil doublers (0.010-in.-thick aluminum) were used to insure firm gripping with a minimum of damage to the fibers. The test specimens were transferred to the testing machine in a rigid fixture and mounted in the self aligning loading train. Testing was performed using a Tinius Olsen four screw testing machine with a torsion bar LVDT load

Jan 1, 1970

By K. Sallmann

Spurred by a variety of factors, coal flotation is making headway among the preparation plants of West Germany. The author gives some statistics on German coal flotation plants and information on the properties of the feed and quality of the derived products. Types of machines and reagents used, dewatering practices, tailings disposal, and thickening operations are covered. There is special emphasis on the many-sided problems that confront German coal preparation engineers. The coal mining industry of West Germany is concentrated in three coalfields: the first on the Ruhr and the Rhein rivers, the second on the Saar river, and the third near the frontier between Germany and the Netherlands, around the towns of Aachen and Erkelenz. The total run-of-mine production of these three coalfields amounts to 736,000 tpd which come from 145 collieries. There are 121 washeries, 43 of them with a flotation plant. The total throughput of these 43 washeries is 280,000 tpd, out of which 26,000 tons (9.3 pet of the washery feed coal) are cleaned by flotation. The capacity of the individual flotation plants varies within relatively wide limits, the average being 40 tph and the capacity of the largest flotation plant being 120 tph. During the last few years, the number and size of flotation plants have been steadily increasing, although flotation must be looked upon as an expensive and rather complex cleaning process. The considerations which have led to the widespread application of flotation may be summarized as follows: 1) In making coking coal, it is seldom possible to add uncleaned fines to the coke oven charge, as their ash content is too high. If, however, the ash content of the fines is reduced to a maximum of 7 or 8 pet, they can be admixed to the washed and crushed small sizes without difficulty. This means, naturally that revenue is increased since the price of coking fines is always higher than the price for dust or uncleaned wet fines. 2) To prevent silicosis and pneumoconiosis, water infusion and spraying of the coal are practiced much more today than ever before. As a result, moisture content of run-of-mine coal has markedly increased and the washery feed coal contains more and more slurry instead of dry dust. The price of slurry, how- ever, is very low, and in many cases it is impossible to sell filtered raw slurry with a moisture content of 20 to 25 pct and, at the same time, 20 to 25 pct of ash. Reduction of the ash content of these slurries improves the possibility of dewatering them and, in this way, also enhances the marketability of this product. 3) The new severe laws and regulations against pollution of air and rivers make it necessary to de-dust coal better than in the past and to reduce the quantity of the waste water from coal preparation plants and their solids content to a minimum. 4) Even if there were no compulsory reasons to clean the fines, flotation will often lead to an increase in the overall yield. Although not the only application, it appears that the treatment of coking fines is the primary field for the flotation process in coal preparation. It must not be overlooked, however, that a series of arguments may be advanced against flotation: 1) Flotation is an expensive process because, in addition to the cleaning operation itself, the dewatering of the froth and the disposal of the tailings is very costly. 2) Operation of a flotation plant requires well trained personnel. 3) Filtered froth has about a 20 pct moisture content and, therefore, if mixed with the cleaned small coal it causes an undesirable increase in water content of the coke oven charge. For this reason it is necessary to take additional measures for dewatering washed small coal and this, of course, entails additional expense. 4) Disposal of flotation tailings involves very difficult problems, particularly in the highly industrialized regions. An investigation covering 32 flotation plants of Western Germany shows the following composition and properties of their feed:

Jan 1, 1961

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

Binary alloys of titanium with silver, lead, tin, nickel, copper, beryllium, boron, silicon, chromium, molybdenum, manganese, vanadium, iron, and cobalt were studied. One-half-pound ingots of the alloys were prepared in an arc furnace, employing a water-cooled copper crucible, an argon atmosphere, and a water-cooled tungsten electrode. The half-pound ingots were fabricated by forging at 1700°F in air to 1/4-in. slab, followed by hot rolling at 1450°F to 0.060-in. sheet. Tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships were determined for these alloys. EARLY in 1947, as one phase of the evaluation of materials for Air Force Project RAND, Battelle successfully arc melted Bureau of Mines titanium and obtained a few basic properties of unalloyed titanium and several titanium-base alloys. The low density, excellent resistance to corrosion, and high tensile properties of these materials stimulated a great deal of interest among metallurgists and designers seeking better materials of construction. As a result of this early work, Battelle, under contract with the Air Materiel Command, Wright-Patterson Air Force Base, has continued extensive studies of titanium alloys. The result of the first year&apos;s work is described in three papers. The present one deals with binary alloys, the second with ternary alloys, and the third paper with quaternary alloys. Melting Method The arc furnace for melting titanium and other refractory metals was developed at Battelle Institute under Air Force Project RAND. During the present work, considerable improvement has been made in the design and operation of this furnace for making small ingots of titanium and titanium alloys. The improved furnace design is illustrated by fig. 1, which shows a cross-sectional view with the dimensions of various parts and their relationship to one another. The essential features of the furnace are the inert argon atmosphere, the water-cooled copper crucible, and the water-cooled tungsten elec- trode. The melting crucible is formed by spinning 0.064-in. annealed copper sheet. A groove for an O-ring seal is spun into the flange of the crucible. A fiber gasket between the crucible flange and the water-cooled brass cover provides electrical insulation. The brass cover is fitted with a sight glass, an opening for the water-cooled electrode, and a tube through which the material is charged. Direct current is used for melting, with the positive electrical terminal connected to the water jacket and the negative terminal to the electrode. A typical heat is made in the new furnace as follows: Approximately, 0.20 lb of titanium under 2 mesh per in. and the alloy addition, if any is to be used, are placed in the bottom of the crucible. The cover is clamped on the crucible so that the O-rings make a tight seal. The remainder of the charge is placed in a glass bottle, and this is connected by a rubber hose to the charging tube of the furnace. The crucible and the charge are evacuated with a mechanical pump to a pressure below 50 mm of mercury, or less if desired, and held at this reduced pressure for 5 min. Hot water is circulated through the jacket during the evacuation period to assist in outgassing the crucible. Following the evacuation, tank argon of 99.92+ pct purity is flushed through the crucible for 5 min and then adjusted to give a positive pressure of 1 to 2 psi. During subsequent operation, an argon pressure regulator introduces only enough argon to compensate for the small leakage which occurs through a mercury trap. Re-evacuation and reflushing the melting chamber with argon produced a negligible reduction in contamination. Two 550-amp generators, connected in parallel, constitute the power source. Normally, about 800 amp are used for melting alloys which are not extremely refractory. The generators are set for 90 v open circuit and 200 amp. The arc is struck and the electrode is withdrawn to produce an arc of 23 to 26 v. This voltage is maintained while the electrode tip is moved slowly around a circle 1 in. smaller than the diameter of the ingot. The current

Jan 1, 1951

By IRVING H. WENTIVORTII

(New York Meeting, February, 1912.) THE little town of San Nicolás, Tamaulipas, Mexico, lies approximately 60 miles east of Linares, situated in the State of Nuevo Leon, and 150 miles SE. of Monterey, as shown in the sketch-map. Fig. 1. The place is reached from Monterey by the Tampico train as far as Linares, a distance of 92 miles, and then by coach the rest of the way. It is situated in a narrow valley between low hills, the houses forming one main street and a plaza. It is peopled by about 500 inhabitants. The climate is temperate, the thermometer ranging from 90° in summer to a few degrees below freezing-point in winter; but this severe weather only lasts a day or two at a time, when the " northers " blow. There are no streams in the vicinity, but water sufficient for the use of the people is obtained from wells. The rainfall is about the same as that in the rest of NE. Mexico. The rainy months are July, August, and September. The rest of the year is practically dry, with an occasional showery day or two during the winter, when a " norther " is blowing. Timber is abundant in many localities. There are two varieties of oak, besides mesquite, ebony, "maguira," "patol," and a number of other kinds of trees indigenous to this region. I. HISTORY. On the discovery of the silver-lead hearing veins occurring in this district, the mining-camp of San Nicolás was founded in 1767 by the Spaniards, and numerous mines were opened and worked for a distance of abort 3 miles east and 5 miles west of the town. At the western extremity and near the Carrolena mine, a small town called San Pedro was built. The ruined walls of the houses form a single street, and all is over-

Aug 1, 1912

By J. D. Dixon

Procedures are given for calculating stresses in underground tunnel supports which accounts both for the structural behavior of the support and that of the adjacent rock mass. Stresses in the support are caused by service loads and rock reactions. Service loads are due to rock pressures, hydrostatic and hydraulic pressures, selfweight of the support, or other utilitarian-type loads. Rock reactions, equal and opposite those in the support, are due to the deformational interaction that results as service loads deform the tunnel support against the adjacent rock mass. The procedures developed for solving this problem are an application of matrix structural analysis. The principles involved in this method allow for the consideration of the deformable characteristics of most tunnel support systems and an iterative solution procedure is applied to determine the areas of support-rock interaction. Numerical results of example problems are given.

Jan 1, 1972

By H. C. Jennison

Two distinct types of defects occur at times in copper wire as a result of the use of dies of improper design or undesirable wire-drawing practice. The conditions under which these defects may be produced, as well as precautions to be taken in order to prevent them, have been known to The American Brass Co. for many years. The quality of the copper wire bars and rods has too often and unjustly been held responsible for these particular defects and it is to correct any such belief that this paper is presented. An extremely high quality of electrolytic copper has been supplied to the trade by all refineries for the last 20 years at least. The purity of the copper would average well above 99.900 per cent. The casting of the wire bars has been handled in a generally satisfactory manner. The bars have been cast sound, with a flat to slightly crowning set and have been free from sloppy edges, cold sets, etc. In other words, the wire bars have met A. S. T. M. specifications and have been generally satisfactory. For the most part, they have been everything that could be desired from a quality standpoint yet most of the wire mills in this country and in Europe have at times held the quality of the copper responsible for the two types of defects described in this paper. As a matter of fact, these defects are produced entirely in the wire mills. The author has visited many of the large wire mills in the United States and in Europe to investigate these defects. In some cases the trouble has been so serious that the wire mill has ceased operations. At times the wire mills are reluctant to believe that they are responsible for the defective product. The effect of die design, wire-drawing practice, etc., upon the quality of copper wire has received&apos; little study on the part of wire mills, particularly those that have commenced operations in the last few years.

Jan 1, 1930

By J. V. N. Dorr

DEADWOOD and the Black Hills were familiar names to me from childhood, for. I had an uncle who was among the earliest eastern investors there and I used to hear of the Uncle Sam mine and its rich ore back in the eighties. The spring of my junior year at college, in 1893, brought me an offer of summer work at the Deadwood & Delaware smelter, in Deadwood, and full of the thrill of the long journey from New Jersey, I went out as chemist and stayed four months. Within a week or two of my arrival, I went through the tragic experience of seeing an associate drink cyanide by mistake and die within a few moments. I shall never forget the horror of feeling that my lack of knowledge of an antidote might be responsible for his death, but I found later that the solution he drank was so strong that nothing could have been done. A year after graduation, when I had settled down to chemical research work in New York, an offer came to go back to the smelter in Deadwood, and within a few days I was again tramping down "the Gulch" with my lunch bucket and putting in the standard assay office shift of that day, from 7 a.m. to 6 p.m., with a half-day off on Sundays. During my absence East, the D. & D. smelter had been changed from a pyritic smelter, using native pyrite, and Homestake concentrate to matte the siliceous gold ores, into a copper-matting smelter using copper ores brought from Butte, over the newly-completed Burlington rail-road. The work was interesting, and the laboratory offered many opportunities for making improvements. I remember also undertaking experiments at home on a new method of gold precipitation for the chlorination process and leasing a mine in Strawberry Gulch that promised great things, but soon petered out.

Jan 8, 1927

By Francis L. Bosqui

The following paper embodies a report which I made on the filter-press treatment of slimes at the Liberty Bell mine, Telluride, Colo. At the time this report was submitted, the management deemed it wiser to defer the installation of so costly a plant as the one required, in the hope that some of the many investigators in the field might soon evolve a cheaper and more perfect method of slimes-treatment, and one better suited to the conditions at Telluride. The Liberty Bell ore consists essentially of quartz and clay, with iron pyrites disseminated through the quartz in very fine particles. There is considerable iron and manganese stain in some of the ore, the latter especially in the clays, which are sometimes quite black. Occasionally particles of galena, zincblende, gray copper and a few other minerals are seen, but they are comparatively rare, and not in sufficient quantity to affect considerations of treatment. Free gold is occasionally seen in the quartz, and one or two instances of mire silver have been observed. The milling-plant consists of an 80-stamp amalgamating mill which crushes through 20-mesh screens; 20 Wilfley concentrating tables, taking out, in iron sulphides, about 2 per cent. of the total ore crushed; and a cyanide plant consisting of two tiers of 33 ft. vats, five in each tier, fed by revolving pipe-die tributers. The slimes overflow from the upper settling tanks through gates with adjustable outlets, and thence to a large canvas-plant, which efects only a small saving. This slimes product, of which about 100 tons escape per day (or 38 per cent. of the total ore crushed), contains about 3 per cent. of dry solids. Of this approximately 93 per cent. will pass a 200-mesh screen. The slimes range in value between $3.90 and $4.87 per ton, the values being about equally distributed between gold and silver. The actual averages for ore and slimes during the years 1900-

Jan 1, 1904

By H. L. Hartman

The past 15 years have seen rapid advances in the metallurgy of materials for drill machinery and bits, but rock drilling itself continues to be largely an art. Jet piercing, roller bit rotary drilling, and rotary percussion are all promising new techniques, but the percussion rock drill, still used for 90 pct of the blastholes in U. S. hard-rock mining, has undergone no major modification since pneumatic machines were first used successfully in the 1860&apos;s. This singular lack of progress stems directly from ignorance of the nature of impact failure of rock and the fundamentals of rock penetration in general. For nearly three-quarters of a century, mining engineers did not know what went on at the bottom of a drillhole. More and more, in recent years, investigators in the field have come to realize that to understand percussion drilling they must study the basic action of percussion bits penetrating rock—not the per- formances of commercial rock drills, with their many attendant variables that cannot be isolated or controlled. Using a vertical drop tester, the writer investigated the sequence of rock failure under the impact. of a simple, chisel-shaped bit when changes were made, singly, in significant variables. Results of this and other research are reported here. BASIC CONCEPTS The formation of a crater in rock under the impact blow of a bit can be observed experimentally. Directly beneath the edge of the bit the rock is crushed into fine powder; toward the sides of the crater it chips out into relatively large fragments. An explanation of these phenomena has been offered by Drilling Research Inc. on the basis of work sponsored by this organization at Battelle Memorial Institute (Ref. 1,1954, Summary, pp. 9-18). High-speed photography and force waveforms obtained from strain gages mounted on the bit near the cutting edges recorded the sequence of events in crater formation with a die-shaped or blunt, wedgc-

Jan 1, 1960

By H. H. Hausner, S. Storchheim, J. L. Zambrow

The solid state bonding of aluminum to nickel was studied as a function of temperature, pressure, and time at pressure. The initial results indicated that as the reaction conditions were varied, marked changes in tensile strength occurred. Plots of the log penetration coefficient vs the reciprocal of absolute temperature for various isobars were straight lines displaced from each other. THE techniques of bonding different metals to A each other include brazing, welding, welding by application of a molten phase, and solid state welding without any molten phase present. This last technique, the pressing of metals either at room temperature or at some temperature below the melting point of the metals to be joined, seems to offer interesting possibilities for bonding purposes. However, this technique has not been completely investigated, and very little is known about the diffusion phenomena which occur during solid state welding. Some previous work on the effect of pressure on diffusion1 was inconclusive. This paper is concerned with an investigation regarding the effect that the processing variables, such as pressure, temperature, and time at pressure, have in solid state bonding. The tests were made with aluminum and nickel and special emphasis was given to the strength of the bond between these two metals and to the intermetallic penetration rate during the bonding process. It seems that the effect of pressure on the intermetallic penetration is of particular importance for practical purposes and this effect was therefore studied in detail. Procedure Apparatus: The means of solid state bonding used for this study was that of the hot-pressing technique. This method requires the equipment pictured in Fig. 1 and involved the following procedure. The two metals to be bonded were placed in an aquadag lubricated 18-4-1 tool steel die, 16 in. high by 1.440 in. ID, between punches of 1.366 in. diameter made of the same material. A thermocouple

Jan 1, 1955

By Ogden B. Malin

In conducting the manufacture of extruded brass rods and brass forgings it has been noticed that there is considerable variation in the physical properties, particularly the machinability of different rods and forgings, even though the composition, working temperatures and method of manufacture remain the same. It is the purpose of this paper to attempt to establish the cause and extent of this variation, and also to determine whether variations in composition within certain defined limits influence hardness and machinability to any marked degree. The writer believes that this variation probably is due to the variation in grain size of the metal, therefore the microstructures of several compositions under various conditions of working were examined in an effort to establish this as a fact. Survey of Previous Work in Studying Extrusion Defects Very little has been published concerning defects in extruded and forged brass. In 1921, R. Genders1 $ delivered a paper before the British Institute of Metals, relative to a defect inherent in the extrusion process. This defect, commonly found in extruded brass rod, shows up in the form of a circle in a transverse section consisting of oxides and impurities, and is generally present in the last 25 to 30 per cent of the rod. Genders concluded that the defect is caused by the turning inward of the skin of the billet at the edge of the plunger because the inside of the billet is more plastic than the outside, which is in contact with the cooler container; the outside skin will lag behind to form the rear end of the rod. Genders suggested a movable die as a remedy, and while this met with fair success, it is not used in present practice. About the same time as Genders&apos; experiments, Tucker2 and Rosen-hain3 conducted experiments using colored plasticene in the form of a billet, and found much the same defect as Genders. Dr. Rosenhain State College, Pa.

Jan 1, 1932