Search Documents

By Charles B. Kenahan

A summary of Bureau of Mines research on utilization and disposal of solid wastes is presented, accompanied by an extensive bibliography of related publications. The Bureau's Solid Waste and Materials Recycling Program is directed toward four main areas of research, development, and demonstration: (1) extraction of mineral, metal, and energy values from urban refuse; (2) upgrading and recycling of automotive and related ferrous and nonferrous scrap; (3) utilization and stabilization of mine, mill, and smelter wastes; and (4) recovery and reuse of values from industrial waste products. A contract and grant program that supplements the in-house research and aids in the training of manpower in management of mineral-, metal-, and energy -based solid wastes is also discussed. This publication is an updating of Bureau of Mines Information Circular 8460 issued March 1970.

Jan 1, 1971

By A. R. Naderian

Laboratory strength and deformation testing of freshly blasted sandstone and claystone overburden from Jeebropilly colliery in Queensland and in-situ plate-bearing tests on four backfills of different ages showed that the bearing capacity of backfill is a function mainly of compaction, not of age. The modulus or stiffness of the backfill is significantly increased by previous loading, in some cases up to threefold. Backfill material experiences some compaction through the passage of mining vehicles, likely to provide a bearing capacity that will support normal construction activities; the limited testing performed suggested that completed backfills are capable of supporting loads of up to 200 kN/m2 while sustaining displacements acceptable for a wide range of residential and industrial uses, but may be susceptible to collapse settlements due to saturation in the long term

Jun 19, 1905

By Robert E. Johnson

1962 was the second year of recovery from the mild 1960-61 recession. The year-to-year gain in constant dollar gross national product, our most comprehensive measure of the country's economic performance, was 6.0 percent (from $447.7 billion in 1961 to $474.8 billion in 1962). The unemployment rate declined from 6.7 percent to 5.6 percent. Although it was a good year, there were still unused resources of labor and capital which implied that the economy was operating below its potential. The year-to-year change in the Federal Reserve Board (FRB) index of industrial production of 7.6 percent masked the fact that more than one-third of the growth took place within 196L The monthly index rose only 4.8 percent during 1962, from 114.3 in January to 117.8 in September. The fact that the economy as shown by the industrial index, rose rapidly in the first half of the year only to remain on a plateau of 119-120 during the second half, led some people to fear an imminent downward turn. This did not occur. Neither production nor consumption of mineral fuels advanced as fast as the total economy. But consumption showed more gain than production, 5 percent compared with somewhat less than 4 percent. Production of both crude oil and natural gas reached new highs while bituminous coal production was the highest in 5 years.

Jan 1, 1963

By R. E. Kennedy

"INTRODUCTION In a previous publication4 results were given of numerous experiments made on the in-flammability of gas mixtures consisting of methane, hydro a. carbon monoxide, nitrogen, and carbon dioxide. Data were obtained and tables prepared giving the inflammable limits of each of these combustibles when mixed with various proportions of carbon dioxide and nitrogen. By the use of these data and the application of Le Chatelier's law, it was found possible to calculate the limits of inflammability of any gas mixture containing any or all of the above gases.Various mixtures of the five gases given above were prepared and their limits determined experimentally and then calculated. Good agreement was found between the determined and calculated results when complex gases encountered in mine safety work were tested. Of special significance was the accurate calculation of the limits of inflammability of gases from mine fires, gases from mine explosions, detonation products of explosives, blast—furnace gases, automobile exhaust gas, and other gases of a similar character.Using the method given in the above report, Yeaw5 investigated a number of industrial gases including oven, coal, producer, blue, carbureted blue, and dry quencher gases, and found the determined and calculated results to agree remarkably well, thus giving further proof of the value of such a means of determining dangerous conditions when combustible gases are encountered in practice.GASES FROM A POTASH MINEGases were recently encountered in a potash nine in New Mexico, containing the com-bustibles, methane, hydrogen, and ethane. In one special case a mild explosion occurred when these gases were mixed with the right proportions of air and ignited it therefore became necessary to know the inflammability of these mixtures in order that the proper precautions could be taken to prevent explosions."

May 1, 1932

I attended a funeral in West Monroe, Louisiana, for one of the best powder peddlers I’ve ever known. He started work in 1948 for Dixie Dynamite, a seismograph explosive distributor. His first job was as a truck driver, then magazine keeper and then sales re p re s e n t a t i v e . When Dixie Dynamite quit, he acted as an explosives sales agent for sometime before moving on to Kansas to be a sales rep for a distributor there. We called him the “ragin cajun” long before James Carville came on the national scene messing up things. While he was born in G e o rgia, he was a Cajun at heart. I don’t believe the old saying, “Build a better mousetrap and the world will beat a path to your door.” To me, the best products in the world need to be sold. Two examples of this are the Beta system for TV and the Apple Macintosh computers. Beta is the best system but VHS took over because the Beta people fell down on the selling job. Windows 98 is Macintosh ‘86 but again the engineers were not salesmen. Marion “Johnny” Johnson who was buried only about a half mile from his first magazine site proved that good selling is good citizenship. He could have sold any firstclass product, for he wouldn’t tolerate inferior items, and made a successful career of it, but he chose dynamite and the industry benefited from his talents.

Jan 1, 2004

By I F. Bell, K P. Hammerschmid

Well planned and executed environmental management plans can reduce life-of-mine operating costs and the need to deal with major environmental issues at the time of mine closure. With proper planning during the exploration, feasibility and execution phases of a project, final closure costs can be reduced. The reduction of closure costs should be considered during exploration and initial feasibility studies and when process facilities, waste rock dumps and tailings impoundments are designed. During the mining of the resource, closure cost reduction will depend on effective and efficient environmental management plans for ongoing land clearance, segregation of mine waste materials, management of mine site water and workshop wastewaters, and the establishment of progressive rehabilitation strategies. These issues are the responsibility of planning, production, technical support and maintenance personnel at an operating site. The successful implementation of environmental plans will ensure that all impacts are reduced and that closure issues with major cost implications are addressed prior to closure of the mine.

Jan 1, 1995

By Dave Rose, Jacques McMullen

"The Detour Lake mine is located 200 km northeast of Timmins, Ontario, Canada.The mill processes a free milling gold ore using both a gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 55,000 tpd at 95 microns with the addition of pre-crushing upstream of the SAG mill.The Detour Lake mine has one of the largest gyratory crusher in the world (60"" x 113"") and over the years, many improvements have been made to this crusher with the result of improving plant throughput. This paper will present how choke feeding the gyratory crusher has been found to be one of the main influences on crusher product particle size and plant throughput. It will explain how the effect of choke feeding the gyratory was measured and from that, the various changes made to improve choke feeding of the gyratory crusher.IntroductionOre is hauled from the open pit mine and dumped directly into a single 60"" x 113"" primary gyratory crusher. The live capacity of both the feed and discharge hoppers of the gyratory crusher are designed for two (2) truck loads each, assuming a nominal payload of 300 tonnes per truck. The surge bin under the primary crusher feeds an apron feeder that controls the ore feed rate at approximately 4,200 tph onto a 227 metres long x 1.52 metres wide belt conveyor with a nominal capacity of 4,200 tph.The primary crusher is operated at an open side setting of 172 millimetres to produce a F80 feed to the secondary crushing circuit of 135 millimetres."

Jan 1, 2017

By D. W. Taylor, I. W. Farmer, N. Mojtabai

Rittinger's and Bond's descriptions of rock crushing relate the energy input required to fracture rock and the surface energy required to form new fractures to the change in specific surface area of feed and product during comminution. The potential applicability of this approach to blasting is illustrated, using the results of data from bench blasting tests on Pinal schists and production blasting of Carboniferous limestones. The approach contributes to understanding of the mechanisms involved in blasting and to the design of test blasts. A modified form is presented of the relationship between blasting energy, specific surface area of the muckpile and a rock energy constant related to the discontinuity structure of the rock. The modified equation fits observed data and offers a simple basis for further experiments

Jun 19, 1905

By Slavoljub D. Maksimovic

The Bureau of Mines, through a memorandum of agreement with the State of Ohio, tested a method of constructing seals in abandoned mine openings in Ohio by means of pneumatic stowing of crushed limestone and gravel with sand. A total of five openings and one shaft were back-filled. Pneumatic stowing uses compressed air to convey material through a pipeline and into the mine opening. The stowing equipment consists of a power supply, a blower, a feeder to inject the material into the pipeline through an airlock, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. Well-graded aggregate up to 2 inches in diameter and having sufficient fines is used as fill. The stowing method is safer and faster than conventional methods, is cost competitive, prevents trespass into abandoned mine openings, and eliminates or reduces the exposure of workers to possible hazards since the discharge nozzle can be kept at the mouth of the opening. The equipment is mobile, and, with some modification, the technique could be widely used for sealing abandoned and active mine openings, even in remote locations and during severe weather conditions.

Jan 1, 1982

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2003

By M. Kunst

The creep behavior of three AJ62 alloys was investigated in a wide range of stresses and temperatures. Multi-level tensile creep tests revealed a distinct primary creep stage and a high stress exponent up to a value of 10. The threshold stress concept which is commonly used in combination with high stress exponents was utilized in the analysis of creep behaviour. This resulted in an effective stress exponent for the AJ alloys indi¬cating dislocation climb as the dominating creep mechanism. In addition, microstructural observations of the lamellar eutectic and of the a-Mg-matrix were carried out using opti¬cal microscopy, SEM and TEM. The creep properties of the alloys are discussed in the context of microstructural parameters such as phase volume-fraction, stability and solute supersaturation.

Jan 1, 2006

By M. J. Little

Potgietersrust Platinums Ltd (PPRust) is Anglo Platinum?s only open pit operation. The major slope stability concern at PPRust is rapid, small-scale brittle failure on the west wall of Sandsloot open pit. In order to improve safety and mine more economically, a comprehensive slope monitoring strategy has been implemented. In the last 3 years four new state-of-the-art monitoring systems have been installed namely an ISSI microseismic monitoring system, a GeoMoS automated prism monitoring system, prismless Riegl laser scanners and a GroundProbe slope stability radar (SSR). Groundwater monitoring and visual monitoring have also been improved over the same time period. To complement the visual inspections, SiroVision digital photogrammetry is now used for predicting where future failures may occur. All these monitoring tools provide primary monitoring which is used to identify high risk areas. The SSR is then set up in that area to provide early warning of failure so evacuation can be successfully done. Fault tree analysis has proved that with this comprehensive slope monitoring strategy the geotechnical risk at PPRust is greatly reduced, allowing mining to continue safely and economically in challenging conditions.

Jan 1, 2006

By J. K. Whyatt, B. G. White

A comprehensive survey of mine seismicity and rock bursting during development of two sublevels at the Lucky Friday Mine, Mullan, ID, USA, was conducted to better define rock failure mechanisms and sources of ground control hazards. Survey data included rock burst damage reports, seismic event locations and magnitudes and, for the most energetic events, first-motion information. Several subsets of this database, including large seismic events, rock bursts, and microseismic activity near the face, were analyzed. Elements of the large-event and rock burst data sets were nearly independent. That is, there was no relationship between the risk posed by a seismic event and its energy, although such a relationship is well established for the mine as a whole. All data sets showed that certain geologic features appear to control the spatial distribution of events and the spatial distribution of rock burst risk. The data also suggest that, within the scope of this study. the greatest risk of injury occurs when a pocket of heightened rock burst risk is first encountered and that this risk is controlled when miners adapt their practices to these conditions. Recognition of the role of particular geologic features in the spatial distribution of rock burst hazards provides an opportunity for anticipating, rather than only reacting to, a changing level of rock burst hazard- However, much work will he required to make good on this promise.

By Amitava Gangulee, Michael B. Bever

The order-disorder transition in Ag-Mg alloys in the range 17 to 26 at. pct Mg was investigated and some thermodynamic, electrical and mechanical properties of ordered Ag-Mg alloys were measured. A modification of the phase diagram is proposed on the basis of measured transition temperatures. The stability of the ordered structure is analyzed in terms of the quasichemical theory. Kinetic aspects of the order-disorder transition were also investigated. The energies of ordering at 273°K of Ag-Mg alloys were measured by liquid metal solution calorimetry. The electrical resistivities and the tensile Properties of the ordered alloys were measured. The exothermic energy of ordering increased with magnesium concentration up to the composition Ag3Mg; it is discussed in terms of the quasichemical theory. Pronounced order hardening was observed and can be explained by several strengthening mechanisms, which are particularly effective because of a change in crystal structure associated with the ordering transition. IN silver-rich solid solutions containing approximately 17 to 26 at. pct Mg, long- range ordering may occur during appropriate therma1 treatments. Clare-brough and Nicholas1 first detected such long-range order in the solid solution of composition Ag3Mg and suggested that the unit cell of the superlattice contained 256 atoms. x-ray2 and electron diffraction3 investigations confirmed the occurrence of long-range order, but indicated a shifted Ll2-type structure. On the basis of recent X-ray measurements the crystal structure of ordered Ag3Mg has been confirmed as type D023.4 The present paper is concerned with the order-disorder transition in silver-rich Ag-Mg solid solutions and some thermodynamic, electrical, and mechanical properties of the ordered alloys. The effects of short-range order on the properties of silver-rich solid solutions containing up to 26 at. pct Mg are discussed in a concurrent paper.5 1) EXPERIMENTAL PROCEDURES 1.1) Preparation of Specimens. Specimens of Ag-Mg alloys containing from 18 to 26 at. pct Mg were prepared in the form of 1.0-mm-diam wires as described in Section 1.1 of Ref. 5. Disordered specimens were prepared by annealing at 773°K for 1 hr and quenching into iced brine. Ordered specimens were prepared by annealing at 773°K for 1 hr and slowly cooling to room temperature over a period of 15 days. The specimens were stored at 78°K. 1.2) Resistivity Measurements. Electrical resistivi- ties were measured by a potentiometric method.' Equilibrium values were obtained at several temperatures. The kinetics of ordering were investigated by following the time-dependent changes of the resistivity of initially disordered specimens during annealing. The specimens were enclosed in copper capsules and immersed in salt pots; the heating up was accelerated by injecting preheated helium into the capsules. 1.3) Calorimetry. The energies of ordering of the alloys were measured in a tin solution calorimeter as the difference between the heat effects of additions of completely ordered and disordered specimens of the same composition. The procedure and the method of calculation have been described.6 Magnesium was used for thermal compensation in most calorimetric runs in order to improve the accuracy.677 1.4) Mechanical Tests. Tensile tests were carried out with wire specimens at room temperature as described in Section 1.5 of Ref. 5. Microhardness measurements were also made.? 2) RESULTS AND DISCUSSION The characteristics of the order-disorder transition of silver-rich Ag-Mg solid solutions will be discussed first. Some thermodynamic, electrical, and mechanical properties of the ordered alloys will then be considered and compared with the corresponding properties of dis-disordered alloys. 2.1) The Order-Disorder Transition. 2.1.1) Thermodynamic and Structural Aspects. The transition temperatures Tt were determined from discontinuities in the slope of the equilibrium resistivity vs temperature curves. Normalized curves for three compositions are shown in Fig. 1. The transition temperature increases with the magnesium concentration and reaches a maximum at the stoichiometric composition Ag3Mg. The transition temperature of the alloy Ag3Mg was measured as 665° ± 2°K and compares with published values of 660°,1 663°,8 and 66°k.3 In the slopes of the resistivity vs temperature curves of alloys containing 22.2 and 22.5 at. pct Mg, discontinuities were observed at two temperatures. Such upper and lower discontinuities indicate a two-phase field. A modified form of the published phase diagram9 is shown in Fig. 2. A two-phase field was found only on the low-magnesium side of the composition Ag3Mg. On the high-magnesium side, the existence of a two-phase field could not be established because of insufficient resolution, but such a field must be present. This part of the phase diagram can be made complete by a eutec-toid-type reaction a = (a' + ß). The existence of a boundary between the two-phase fields (a + ß) and (a' + ß) is also in accord with published lattice parameters.3 The crystal structure of ordered Ag3Mg (type Do23)

Jan 1, 1969

By A. Broussaud, J. D. McKay

Benefits analysis of adaptive Expert control systems operating at plants in Africa and the United States are presented. Proper statistical tools and techniques are discussed. Technical and practical pitfalls of strategy comparison are also presented and illustrated with from published data. Advantages and disadvantages of a “Pay for Performance” approach to a project are reviewed.

Jan 1, 2001

The Calypso geothermal field, mapped by the R V Sonne (cruise SO-135) in 1998, includes four main sites, the Northern Vent Area (centred on 37¦ 36.7'S, 177¦ 06.2'E, area 1.5 km2), Central Vent Area (37¦ 39.4'S, 177¦ 05.2'E, 1 km2), Southern Vent Area (37¦ 41.7'S, 177¦ 06.0'E, 1 km2) and Mercury Vent Area (37¦ 41.3'S, 177¦ 07.3 'E, 0.5 km2). Hydrothermal activity at the vent sites is controlled by minor, sub-parallel NE-trending normal faults. Gas bubble trails (C02) and shimmering hot water vent from fractures and joints between large blocks of silicified volcaniclastics and in depressions in the sediments at the base of these outcrops. Measured maximum vent temperatures are between 180¦C and 201¦C. Venting fluids are at, or just below, boiling for water depths of 200 m. Rock samples recovered by dredge from the sites include massive anhydrite, clay-altered pumiceous ash, silicified volcaniclastic sediments and volcaniclastic breccias cemented by sulphur. Clay-altered samples, dominated by randomly interstratified illite-smectite and accessory chlorite, indicate formation environments of 70¦C to 90 ¦C. Native sulphur is abundant throughout the samples. Fine-grained (<1 mm) disseminated pyrite and vein pyrite occurs in the clay-altered pumiceous volcaniclastics and argillites. In the Southern and Mercury Vent Areas, fine-grained orpiment, realgar and cinnabar have deposited in the sandy matrix of volcaniclastic breccias. Amongst the cinnabar, small (<2 mm) beads of native Hg formed on the surface of several rocks following their recovery. These samples also contained abundant light hydrocarbons, which coat the rocks with an oily sheen.

Jan 1, 1999

By A. Moergeli

The Swiss are currently building the world’s longest tunnel, the 35-mile long Gotthard Base Tunnel. At Sedrun, for the first time in tunneling, four Roadway Support Machines will drive through most difficult ground, supporting variable diameters of up to 13 m. The machines are prepared for their first deployment. At Amsteg, two Hard Rock TBMs have successfully crossed a known fault zone by applying full circle steel arches and shotcrete immediately behind the cutter head. Comparisons between Drill& Blast and Hard Rock TBM are shown.

Jan 1, 2005

By Andrew P. Jarosz

The present computerized mine planning systems use CAD-like and Data Base Management System (DBMS) environments for the handling of numerical, textural, and graphical data. These two environments are usually integrated, that the data provided by the DBMS are linked to any graphical element rendered by the CAD system. The subsidence monitoring, analysis and prediction process should be integrated with the mine design process. It should allow for the assessment of impacts of mining on surface, surface utilities, and structures. It should also provide for the measures to control mining, that will create only acceptable levels of negative impacts on the surface. The common data base, and graphical capabilities of the CAD interface, may be used with great advantage for both systems. The findings of the subsidence engineering modulus should be directly incorporated into the mine design system, and vice versa. In this paper the author suggests guidelines for the development of the comprehensive computer system, able not only to predict the vertical and horizontal components of the ground movement, but also assess the induced surface damages, and costs related to subsidence prevention and compensation.

Jan 1, 1995

By Irwan S. Halim

For tunnels in horizontally bedded rock, geologic factors affect the selection and design of the initial supports, including the rock propensity toward parting along bedding and the resulting high potential for rock slabbing during excavation. To evaluate this ground behavior, numerical analyses and results with Mohr-Coulomb, Hoek-Brown, and Ubiquitous Joint constitutive models were used, using the Upper Rouge CSO tunnel in Detroit, Michigan as an example. The different rock models and other geologic considerations are shown to impact the selection of the tunnel initial support and design. This paper emphasizes the appropriate selection of an analytical model based on the site specific geology to achieve an optimum initial support design.

Jan 1, 2008

Consumption and intensity of use trends for twelve metals, by industrial end use, were estimated for 1972 through 198Z. The trends were then forecast through 1993 using standard statistical methods. The intensity of use measure selected is the quantity of metal consumed per constant dollar output of a specific industrial sector. The metals studied were aluminum, chromium, cobalt, copper, lead, manganese, nickel, the platinum-group metals, tin, titanium, tungsten, and zinc. Average annual growth rates for the following four of the twelve metal increased from 1972-82 as follows: aluminum, 1.00 percent; platinum-group metals (consisting of platinum, palladium, and iridium), 8.83 percent; titanium, 7.82 percent; and tungsten, 6.09 percent. Consumption. for the remaining eight metals decreased at average annual rates ranging from 0.58 percent (copper) to 5.37 percent (manganese).

Jan 1, 1986