Search Documents

Remember, the good of the Institute is not limited to the technical papers. The acquaintance and good fellowship, the education and broadening effect of our meetings, can be made a real benefit for us all. Don't forget the meetings. The nest one will be at Denver, Feb. 26, 27 and 28. THE SECRETARY

Jan 1, 1922

By F. Bruey

The Factorial Model Experimenters are often interested in systems that are multi-factorial. A multi-factorial system is one whose output is believed or known to be dependent on the particular settings of several inputs, or factors. We can think of these factors as defining a space, with each point in this space corresponding to a particular set of factor settings. Experimenting can be thought of as exploring this space - finding out how the response of the system changes as factor settings are changed. There are several challenges in this exploration, among which are deciding what region to explore, designing an experiment that explores it most effectively, and describing the results of the exploration. This paper deals principally with the last of these; it shows how the factorial model can be used to describe how the response of the system changes as factor settings are changed. A strength of the factorial model is that it treats the factors as causes of change in the system's response and focuses on relations among these causes. In particular, the factorial model focuses on whether causes act independently on the system (in a sense to be explained below), or whether they interact. This is important because the experimenter generally seeks to control the system, and because control based on causes that act independently of other causes is relatively simple, whereas control based on causes that interact is more challenging. Also, mapping the space - finding out how the response of the system changes as factor settings are changed - will require less work if, during the exploration, it can be determined which of the causes act independently. For the sake of example, let us assume that the space we are exploring is three-dimensional, and that we have already defined, for each of the three factors, the range of interest. Let us consider all the ways in which the response of the system might depend on the settings of these three factors. In the simplest case, the response in this region does not depend on any of the factors. The response is constant throughout the space, at say, 80 units.

Jan 1, 2007

By Peter Richards, Alexander Lewis-Gray, Mark Davies, Nicholas Katsikaros

"Gekko Systems developed the Gekko Resin Exchange Column (G-REX) in order to optimise the recovery of gold in complex leach-to-electrowinning processes, as an intermediate step using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin (Lewis-Gray et al, 2015). Operational experience has been gained at the CGT Ballarat Gold Plant in near continuous operation since 2008, treating unclarified concentrate leach solution. The extension of the technology to higher throughputs and more complex chemistry is discussed.Aurix®100 ResinAuRIX®100 resin is a cross-linked polystyrene alkaline resin developed by Henkel (Virnig et al, 1996). The resin beads are off-white in colour, spherical, with a nominal size of 100% +600µm. This resin is highly selective for gold and silver over many metals, by way of extracting precious metal cyanide complexes from leach solutions with a pH less than 11.5. The higher end of the pH scale produces best selectivity according to the order of preference: Au > Ag > Hg > Zn > Ni > Cu > Co > Fe. Purolite produces the resin and Gekko Systems maintains licensing of AuRIX®100 resin for use in its G-REX column as part of its unique suite of gravity gold handling equipment.Significant cost savings over carbon-in-solution (CIS) systems are realised with AURIX®100 resin, of around 4% to 12% in capital savings and 27% to 40% in operating costs (Virnig et al, 2004). Allied to this is that AuRIX®100 resin is not susceptible to fouling, that is, the resin does not load with inorganic salts or organic compounds which would affect the loading and extraction of precious metals. To counter any potential for fouling by inorganic salts, in service a dilute acid wash is carried out periodically on the resin to unblock resin pores."

Jan 1, 2016

By F. E. Cash

"Explosions in bituminous coal mines are preventable. The combination of adequate ventilation, thorough rock-dusting, and water on the cutter bars of mining machines and of empty and loaded cars will certainly reduce the hazard to a minimum, if not remove it entirely. This is the attitude taken by the Woodward Iron Co. in lessening or removing the dust and gas explosion hazard from its Dolomite and Mulga mines.This report was made possible through the willingness of Frank H. Crockard, president of the Woodward Iron Co. to make records available and to authorize their publication for the benefit of the coal-mining industry.The compilation of these data and preparation of maps was facilitated by the cooperation of M. Heard, general superintendent of coal mines, J. B. Whatley, assistant general super-intendent of coal, and R. P. Whetmore, chief mining engineer.The Dolomite and Mulga mines are about 16 miles southwest of Birmingham, Jefferson County, Ala., on a company owned and operated railroad which connects ore mines, coal mines, coke ovens, and furnaces.In the Dolomite property there is a 30°, 860-foot, double-tracked slope for hoisting, three manway and air slopes and one air shaft, all in rock.At Mulga there is a 220-foot hoisting shaft, an air shaft and two manways, and material and air slopes, all in rock to the coal bed.The coal in both mines comes from the Pratt bed, which is the next coal above the Mary Lee bed in the Warrior Basin. The coal is horizontal or slightly undulating, with thickness varying from 36 to 72 inches and averaging 50 inches.The method of mining is essentially room-and-pillar with modifications for mechanized sections. The mines produced approximately 1,100,000 tons with 2,328,309 man-hours exposure n 1929 and 900,000 tons with 1,697,436 man-hours exposure in 1930.Through the work of the safety department the entire personnel in the coal mines, as well as in other departments, makes safety an essential part of efficient operation.Both mines are gassy; Dolomite produces about 334,000 cubic feet and Mulga about 919,000 cubic feet of methane every 24 hours.The ventilation maps, two of Dolomite mines (figs. 1 and 2) and one of Mulga (fig. 3) give as much of the details of ventilation as is practicable to put on maps of such scale. As will be seen from these maps there are two main ventilating fans in Dolomite mine and two in Mulga mine and the general direction of the air travel is indicated by long arrows to fan 1 and short arrows to fan 2 in each mine. Each fan has a gas or steam auxiliary drive and each mine has a complete fan and power unit ready for operation in emergency.In Dolomite, recently taken data show that fan 1 exhausts 82,000 cubic feet of air per minute at 3.2-inch water-gage pressure, with an analyzed methane content of 0.15 per cent, and fan 2 exhausts 115,500 cubic feet of air at 3.8-inch pressure and 0.10 per cent of methane. In addition, a Capell fan at No. 2 air shaft is a standby or emergency unit.In Mulga recently taken data show that fan 1 exhausts 83,000 cubic feet of air per minute at 3.0-inch pressure and 0.18 per cent of methane, and fan 3 exhaust 119,000 cubic feet of air per minute at 5.4 inch pressure and 0.35 per cent of methane. Fan 2 at No. 2 shaft is a standby or emergency unit for the Mulga mine.The ventilation is on a split system in both mines. All part split and total returns are measured, sampled, and analyzed weekly, requiring one man two days each week. During December, 1930, 77 samples were collected and analyzed in Mulga and 78 in Dolomite. Two weekly reports covering part of December, 1930, are given here so that they can be studied to show control of ventilation in the Dolomite and Mulga mines. In the event that a split sample shows more than 0.50 per cent of methane, immediate steps are taken to lower the explosive-gas content. The reports follow:"

Mar 1, 1932

By Carrie Smith

Mining has historically been one of the most male-dominated industries in the world. From underground operations to executive boardrooms, the presence of women has often been slim. Women had often been excluded from operational, leadership and decision-making roles, both by cultural norms and systemic barriers. According to PwC’s Global Mine Report (2023), women represent around 14 percent of the global mining workforce. Leadership representation, however, remains sparse, with S&P Global’s 2023 report showing women holding approximately 12 percent of C-suite positions and only 3 percent of senior leadership roles globally. These figures reflect persistent gaps, but they also highlight the progress driven by a new generation of women transforming the industry. Despite the gender imbalance among mining workers, women have continuously made grand strides within the industry, resulting in pivotal changes. At the forefront of this transformation is Kimberly Morrison, one of several women who have played pivotal roles in shaping the mining sector.

Aug 1, 2025

By D. F. Malan

This paper gives an overview of the difficulties associated with determining the strength of hard-rock pillars. Although a number of pillar design tools are available, pillar collapses still occur. Recent examples of large-scale pillar collapses in South Africa suggest that these were caused by weak partings that traversed the pillars. Currently two different methods are used to determine the strength of pillars, namely, empirical equations derived from back analyses of failed and stable cases, and numerical modelling tools using appropriate failure criteria. The paper illustrates that both techniques have their limitations and additional work is required to obtain a better understanding of pillar strength. Empirical methods based on observations of pillar behaviour in a given geotechnical setting are popular and easy to use, but care should be exercised that the results are not inappropriately extrapolated beyond the environment in which they are established. An example is the Hedley and Grant formula (derived for the Canadian uranium mines), which has been used for many years in the South African platinum and chrome mines (albeit with some adaptation of the K-value). Very few collapses have been reported in South Africa for layouts designed using this formula, suggesting that in some cases it might yield estimates of pillar strength that are too conservative. As an alternative, some engineers strongly advocate the use of numerical techniques to determine pillar strength. A close examination unfortunately reveals that these techniques also rely on many assumptions. An area where numerical modelling is invaluable, however, is in determining pillar stresses accurately and for studying specific pillar failure mechanisms, such as the influence of weak partings on pillar strength. In conclusion, it appears that neither empirical techniques nor numerical modelling can be used solely to provide a solid basis for conducting pillar design. It is therefore recommended that both these techniques should be utilized to obtain the best possible insight into a given design problem. Owing to the uncertainties regarding pillar strength and loading stiffness, monitoring in trial mining sections and in established mining areas is also an essential tool to test the stability of pillar layouts in particular geotechnical areas.

Jan 1, 2011

By Richard N. Spencer

Electric-furnace smelting for simultaneous recovery of zinc spelter and lead bullion from complex lead-zinc sinter was investigated. Reduction of lead and zinc was satisfactory. Condensation of lead and zinc vapor to pyrophoric metal powder in a water-cooled, shock-condensing system produced excellent recoveries. Metal-splash condensation to produce zinc spelter was unsatisfactory. Special smelting experiments differentiated the effects of several smelting parameters on zinc metal recovery. The principal cause for unsatisfactory zinc metal recovery was transfer of iron to the condenser and subsequent degradation of zinc in a mixture composed of lead and an iron-zinc intermetallic compound. Limitations of the process were determined. Slag-resistance open-bath electric smelting of complex lead-zinc sinter is not considered feasible.

Jan 1, 1967

By Thomas M. Barczak

Roof support systems are necessary to provide stable mine openings and much research has been conducted to design a variety of roof support systems that will function in various manners to ensure that stable ground conditions are achieved. Despite these advancements in technology, mistakes continue to be made in the evaluation and/or installation that significantly degrade the support capability or lead to erroneous determinations of support expectations. The purpose of this paper is to discuss misconceptions about how roof supports perform and factors that impact their performance. The goal is to present practical information that will assist mine operators and engineers in selecting, installing, and evaluating roof support systems properly, and help them to avoid mistakes that can lead to erroneous expectations and potentially catastrophic results that may lead to roof falls. The paper is limited to a discussion of secondary roof support systems and powered roof supports such as longwall shields.

By J E. Nethery

At the Red Dome and Mungana deposits in north Queensland, Australia, it is proposed that mineralisation and alteration developed as a 'telescoped' overprinting continuum, ranging in style from hypothermal to epithermal, reflecting the major changes that developed in the regional setting over the period circa 325 - 290 Ma. Regional assessment suggests that this also applies to many other precious and base metal deposits within a 40 km length of the host Siluro-Devonian Chillagoe Formation.   A ten stage paragenetic sequence of structural preparation, multi phase intrusion and associated mineralisation, alteration and brecciation is postulated for the Chillagoe district.

Jan 1, 1995

By M. M. Tilman

The Bureau of Mines conducted research to determine the feasibility of strengthening experimental magnesium-base sheet alloys by strain softening induced by controlled cold rolling followed by selective heat treatment. Relatively small alloying additions having potential for producing strain softening were selected from metals that are readily avail-able. Tensile properties comparable to minimum properties of the most commonly used magnesium-base sheet alloy AZ31B, in the H24 condition (strain-hardened and partially annealed), were obtained in an Mg-IMM (mischmetal)-O.5Mn alloy after strain-softening rolling followed by heat treatment. Tensile properties of the experimental alloys in certain conditions are also compared with minimum tensile properties of other standard magnesium sheet alloys. Incidental to the principal objectives, apparent superplastic behavior was observed in three experimental magnesium-base alloys containing MM, MM plus manganese, and MM plus zirconium.

Jan 1, 1985

By Michael Forbes, Rick Jeuken

The challenge of managing geological uncertainty in mine planning is central to optimizing resource extraction while minimizing risks and costs. This paper introduces a novel approach to coal mine planning by integrating chance-constrained programming to address the uncertainty inherent in mining operations. The main takeaway from this work is the demonstration that focusing on reducing the variance of high-quality coal blocks, rather than low-quality ones, can lead to better blending outcomes, higher profitability and more efficient resource utilization. The study presents a case study of a coal mining operation, using chance-constrained programming to manage the uncertainty surrounding coal property predictions, specifically the predicted coke strength after reaction (CSR).

Jan 1, 2025

By Edwin W. Meyer

The augered cast-in-place piling technique was used to install deep foundations 20 feet into weathered sandstone. The project involved the upgrading of the Air Quality Control System (AQCS) for a 560 megawatt coal fired power plant located in Stillwater, Minnesota. The site subsurface consisted of 20 feet of overburden overlying weak sandstone. The overburden consisted of sands and gravels with cobbles and boulders, and variable thicknesses of peat. Ground-water at the site was approximately 8 feet deep. Two foot diameter piers were selected to facilitate installation through the cobbles and boulders in the over-burden and to penetrate the sandstone 22 feet. During installation of the first pier, the weak sandstone broke down to sand-sized material that could not be cleaned from the pier hole without the use of slurry to hold the material in suspension. However, the use of slurry would significantly impact both schedule and cost. Since the sandstone could be easily drilled with the pier equipment, it was believed that 2 foot diameter deep foundations could be installed as designed using augered cast-in-place piling techniques. A brief test drilling pro-gram was conducted to evaluate the viability of 2 foot diameter continuous flight augers penetrating 22 feet into the weak sandstone. The test drilling indicated that augered cast-in-place installation techniques should be successful. Following a short delay to mobilize the additional required equipment, construction commenced. Installation of the 2 foot diameter augered cast-in-place piling to a depth of 22 feet into the weak sandstone was successfully performed.

Jan 1, 2006

By Walter R. Hibbard

Precipitation in the northeastern United States, Florida, California and in many industrialized areas of the world is now more acidic (lower pH) than can be accounted for by natural causes. At the same time, the acidity of many lakes and streams in the northeastern United States has been measured and found to be similar to that of actual rain. These facts have led to conclusions that the two conditions are related. Coal burning utilities, 700 to 1000 miles upwind, have been accused of being the cause, leading to proposals for strict emission controls on the alleged offenders. The costs of these controls would place an estimated $10 to $15 billion capital burden on utility customers in about 15 states plus $2 to $6 billion annual operating costs. There appears to be no direct well-established scientific evidence that the accused are guilty but that the indictment is based largely on circumstantia1 evidence. This study examines the evidence, describes the situation and proposes what must be done to reduce the acid precipitation in an orderly cost beneficial manner. It is interesting to observe that studies by the different adversaries on the acid precipitation issue come to different conclusions largely because they do not read the same literature, but selectively develop evidence to support their own points of view, This study will try to review the issues impartially and reach a position of scholarly balance.

Jan 1, 1982

By L. Westerstrom

Supply and Demand After a dismal first half, the industry saw a marked improvement in its markets during the final six months of 1983. Domestic consumption was 17.6% higher in the second half of the year, primarily due to a surge in electric power requirements. The sharp increase in demand for electric power during the third and fourth quarters afforded utilities the opportunity to lower stocks that had accumulated to record levels during 1982. Consumer stocks were reduced from 179 Mt (197 million st) at the end of June to 153 Mt (169 million st) by the end of the year. That is the largest inventory drawdown on record during a six-month period without a major coal strike. Despite the huge depletion in inventories, coal production in the second half of 1983 rose 1.3% above output in the second half of 1982. However, because of the disappointing first half, production in 1983 totaled only 712 Mt (785 million st), 6.4% less than the 760 Mt (838 million st) produced in 1982. Demand The extent to which the economic recovery affected coal markets in 1983 varied: • total domestic coal consumption increased 4.2%; • electric utility coal consumption increased 5.3%; • exports declined by about one-fourth; • coal consumption at coke plants declined 9.5%; and • coal consumption in the other industrial sectors increased 2.9%. Domestic coal consumption totaled 667 Mt (737 million st) it 1983, 27 Mt (30 million st) more than 1982. Electric utility consumption increased from 539 M1 (594 million st) in 1982 to 567 M1 (625 million st) in 1983. Coal consumption at coke plants declined from 37 Mt (41 million st) to 34 M1 (37 million st). Residential and commercial use increased 181 kt (200,000 st) - from 7.4 to 7.6 Mt (8.2 to 8.4 million st). Electric Utilities: Electric power generation increased 3.1% in 1983. Demand for electric power increased in all major consumer categories. Residential and commercial use rose 2.7% and 3.3%, respectively. The most striking increase, however, and indicative of the economy's strong upturn, was the increase in industrial electric power use. Industrial power requirements, which declined 9.8% in 1982, rose 4.1% in 1983. The electric utility sector continued to expand its use of coal last year while lowering its requirements of oil and natural gas. In 1983, electric generation from coal increased 5.7%, while genera-

Jan 5, 1984

By A. F. Banks

"Potash processing in Canada commenced on a commercial scale in 1962. Over the last 25 years it has grown into a world-class industry with many advances in processing technology. As it is a relatively young industry, many more advances can be expected. Unlike much of the mineral production in Canada, potash is sold as a range of finished products. The processing involves potash recovery and finishing in about equal amounts in terms of the effort of processing. Environmental concerns are not insignificant and are being treated uniquely in some areas. Research and development efforts, while not carried out on a large scale, are attacking industry problems on a wide front.THE INDUSTRYThe Canadian potash industry has 12 producing mines, 10 in Saskatchewan and 2 in New Brunswick. The total productive capacity of the industry is 18,300,000 tonnes of products per year. At capacity, the industry 1•ill process the equivalent of about 53,000,000 tonnes of ore per year. Plants range in size from 8,000 tonnes to 24,000 tonnes of feed per operating day. In product terms this is from 2,500 to 3,500 tonnes of products per day.Of the 12 mines, 11 are conventional underground mining operations with potash recovery principally by flotation supplemented by crystallization and one is a solution mine where mining is achieved by dissolving the potash and salt in underground caverns and then treating the solution in an evaporator/ crystallizer circuit. In all plants there is commonality of unit operation in the product screening and compaction sections. There are three principal ores being treated in the conventional plants. These may be characterized in general terms as follows:"

Jan 1, 1987

By M. A. Kujoana

Following on the design of good mining layouts and regional support systems, and the implementation of sound strata control practices, stope support is the ultimate strategy to combat the hazards of rockfalls and rockbursts. The primary function of stope support in intermediate and deep level mines is to stabilize the rock mass immediately surrounding stoping excavations, that is, the zone of fractured rock which behaves in elastically around stopes. Support design is a process resulting in a support system which is both practical and meets or exceeds by a factor of safety the requirements for a particular geotechnical environment. The aim of this project was to design a support system, which accommodates the factors of rockfalls and rockbursts. The pack support unit must be easily handled, less costly and can be used in stopes without any significant convergence. The project tested the structural stability of packs to their expected deformation, in order to design a height to width ratio for stopes where little convergence is expected.

Jan 1, 2009

By Peter White

Mine Planning Shaft Collar Shaft Sinking Raises Ramp Underground Water Storage

May 1, 2009

By David S. Yang

The Cement Deep Soil Mixing (CDSM) method introduces and mixes cementitious materials with in situ soils using hollow-stem rotating shafts equipped with a cutting tool at the tip and mixing paddles above the tip. CDSM generally produces a soil-cement panel consisting of three overlapping soil-cement columns. The soil-cement panel is then extended to form walls, which are effective for excavation support and groundwater control due to the continuity and low permeability of soil-cement walls. Two design approaches could be taken in the application of CDSM for excavation support: 1) single wall design and 2) gravity wall design. The former one is treated as a wall technology and the latter one is treated as a soil stabilization method. This paper will review the CDSM equipment and installation procedures for the construction of these two types of soil-cement walls. Four case examples are used to illustrate the design and application of these two types of soil-cement walls.

Jan 1, 2003

By Robert B. Hopler

The history of the first twenty years of the high explosives industry in the United States begins as an illustration of the free enterprise system at its best and ends with the industry virtually taken over by a single company: a company which strongly opposed the new explosive material at the beginning of the period. In the world of the late Twentieth Century we could almost compare this history to the opposition of the mainframe computer manufacturers to the introduction of the personal computer, and their later entry into, and attempted dominance of, that market. With computers in the twentieth century the attempt to dominate the market has not been particularly successful: with dynamite in the nineteenth century it was.

Jan 1, 1994

By Ketan H. Trivedi

This paper describes the method of analyses used for the design of temporary and permanent Secant Pile Walls, describes various aspects of construction including, guide walls, sequence of pile installation, plan alignment and verticality tolerance, methods of drilling (auger, wash boring, cased and open holes), lateral bracing for secant piles, cutting of keys in secant pile walls for the connection of permanent floor slabs, sealing of water leaks and waterproofing. The paper concludes with a brief case history of a secant pile wall project recently constructed in New York City.

Jan 1, 2006