Search Documents

By Paul H. Madsen, Victor S. Romero

The Tren Urbano project in Puerto Rico includes a 19 m diameter tunnel constructed by the stacked drift method, which involves installation of a pre-supported concrete arch using multiple tunnels. Geotechnical conditions consisted of weak rock and highly weathered, unstable alluvial soils. Due to low cover, reinforcement of the arch was required. Ground behavior ranged from firm ground to mixed-face to raveling and flowing ground. Consequently, construction of the individual drifts involved many different soft-ground techniques such as steel set supports, shotcrete support, shield tunneling, forepoling, and consolidation grouting. During construction, the design was modified to improve constructability. Although settlement was experienced during excavation of the drifts, arch movements were within predicted limits and minimal surface settlement was observed upon excavation of the interior.

Jan 1, 2001

By R. L. Virta

Four companies mined ball clay in four States during2004. They were H.C. Spinks Clay (owned by Franklin Minerals) Kentucky-Tennessee Clay (owned by Imerys),Old Hickory Clay and Unimin. Production was estimated to be 1.46 Mt (1.61 million st) valued at about $56.9 million, based on a preliminary survey of the ball clay industry. In 2003, production was 1.31 Mt (1.44 million st) valued at $56.2 million. Tennessee was the leading producer state with 61 percent of production. It was followed by Texas, Kentucky and Mississippi.

Jan 1, 2005

By Simon Mundike, Muwindwa Lipalile

A scraper based block cave method has been successfully applied to extract the Lower Ore Body at Nchanga since the 1950?s. Since inception, scraper drifts and service ways have been supported using steel arch sets fabricated to a specific design from high strength manganese steel To reduce costs and to improve productivity, trials commenced in 2002 using fibre reinforced shotcrete as an alternative support method. One of the areas; the 2420 8E 1C trial drift was subjected to abutment loading for several months prior to undercutting and cave mining. Shotcrete installed exhibited minor cracking shortly after application but very little deterioration thereafter. Following the success of the trial, the application of fibre reinforced shotcrete was extended to other drifts. This paper describes the application of fibre reinforced shotcrete at Nchanga and outlines design and quality assurance methods employed.

Jan 1, 2005

The prediction and control of ground deformations due to underground mining are important considerations in the permitting, planning, and monitoring of coal mining operations. The prediction of mining-induced ground movements using the influence function method is a mature technology and is widely used in many coal basins around the world. Such movements mainly include subsidence, horizontal displacement, and horizontal and/or ground strain. Predictions can be accomplished using regional subsidence parameters and site-specific data.

Jan 7, 2020

By Jan Van Greunen, Mark Vanderzee, David Haug, Geoffrey Hughes, Yiming Sun, Roozbeh Geraili Mikola

"The Sanitation Districts of Los Angeles County is planning to construct a new, approximately 7-mile-long (11.3 km) effluent outfall tunnel to be excavated by TBM and lined with precast concrete segments. Anticipated net operating pressures within the tunnel are expected to approach 3 bar. To counteract joint opening and exfiltration leakage, an approach has been investigated to post-tension the precast concrete tunnel lining with steel tendons. The tunnel alignment crosses several seismically active fault zones, at which installation of steel pipe is proposed as a secondary inner lining to mitigate potential offset displacements. This paper discusses the tunnel lining design approach and methods used to address these unique challenges.INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) is planning to construct a new 18-foot-diameter (5.5 m), approximately 7-mile-long (11.3 km) tunnel from the Joint Water Pollution Control Plant (JWPCP), located in the City of Carson, to the existing White Point outfall manifold structure at Royal Palms State Beach (RPSB) (Figure 1). The project is part of the Sanitation Districts’ Clearwater Program, which will improve overall system reliability through the repair and replacement of the existing aging infrastructure. The existing system includes two 6-mile-long (9.7 km) tunnels, 8- and 12-feet in diameter (2.4 and 3.7 m), and four ocean outfall pipes with a maximum capacity of approximately 675 million gal/day (MGD) (2.6 billion L/day). Addition of the new parallel tunnel will increase overall capacity to accommodate peak wet weather wastewater flows of up to 1,262 MGD (4.8 billion L/day) and will allow inspection and repair of the existing tunnels. The new outfall tunnel will be excavated using a pressurized face tunnel boring machine (TBM). Shafts at the north (JWPCP Shaft) and south (RPSB Shaft) ends of the proposed alignment will connect the tunnel to the existing wastewater treatment plant and existing ocean outfalls manifold and during construction act as launch and receiving shafts for the TBM. The tunnel will be excavated from north to south as a single heading."

Jan 1, 2016

Study on Influence that Styrene-Phosphoric has on the Surface Property of Rutile Minerals

Sep 13, 2010

By Marc C. Bétournay

Hydrogen fuelcells are a known technology, having been applied to stationary (e.g equipment, buildings, power plants) and vehicle applications (e.g transit buses, space shuttles). There is currently a growing need to provide alternate power systems to diesel fuel for underground mining vehicles to improve underground air quality and reduce production costs and green house gas emissions. To date, however, fuelcells have not been exposed to underground mine air and physical conditions. A testing program was carried out to provide information on the vulnerabilities of fuelcells as part of a number of proof-of-concept projects to apply hydrogen power to underground mining vehicles. The fuelcell type of choice for the industry, the Proton Exchange Membrane, would function at the range of temperatures encountered in underground and surface operations, and use hydrogen that is stored under low pressure and risk. A small fuelcell stack was tested in a cooperative project between CANMET, the Fuelcell Propulsion Institute, INCO, the Ontario Ministry of Labour, Sandia National laboratories and H-Power. This article will review the tests carried out to measure the effects from high humidity, mineral dust, diesel emission gasses and diesel particulate matter as well as from shock and vibration provided to the unit in underground conditions, at INCO?s 175 Orebody minesite and INCO?s Stobie Mine. The test results provided will show that the unit was not affected by the underground conditions: physically and electrically the unit performed without any reduction in operation or adverse effects imposed.

May 1, 2003

By R. C. Warner, L. Mills, S. D. Botts, M. Marticorena

The Antamina Mine is located in the mountainous region of the Ancash Department of Peru at an elevation of approximately 4200m.The 120 km main access road crosses the headwaters of numerous high-value trout streams and is adjacent to pristine lakes, some of very high ecological and scenic value. In addition, the mine discharges mine water and tailings supernatant to the Antamina and Ayash watersheds. These streams provide the primary water supply for irrigation by local residents and provide excellent fishery habitat. The rock walls and earthen diversions constructed by historic and current indigenous residents of Peru are world-renowned and local residents continue this tradition, passed down from the Inca Civilization, for both agricultural purposes and water distribution. The key elements of sustainable development – economic, environmental and social development have been incorporated into Antamina’s sustainable development program through integration of indigenous knowledge and capabilities into enhanced storm water, erosion reduction and sediment control systems. Examples of incorporating indigenous technologies and knowledge into cost-effective and environmentally sound environmental controls are:(1) placement of rock walls on steep terrain to reduce slope length and erosion, (2) installation of rock walls (porous rock check dams) within elongated sediment ponds to increase detention time, (3) construction of rock-lined ditches to convey clean water (4)use of rock walls, with or without geotextile, to function as a seep berm, and (5) appropriate selection and usage of native Andean species for protection of canals and sediment ponds, and steep slopes.

Jan 1, 2004

By T S. Giraudo

The Macraes Gold Project, operated by GRD Macraes Limited, engaged GRD Minproc Limited to assist with the evaluation of a pressure oxidation circuit, this being the key component of a recovery enhancement project. The initial study gave sufficient confidence in the process to enter into project execution. GRD Macraes Limited was the first company to license Newmont Mining Corporation's pressure oxidation technology, which aims to improve gold recovery from the carbonaceous sulfidic flotation concentrate. This paper outlines the fundamental chemistry of the process followed by a description of the plant that was ultimately installed. A summary of the commissioning is given together with an overview of the production results to date. The project ramp-up was rapid, with design temperature and throughput being achieved within days of hot commissioning. Gold recoveries have exceeded expectations, improving from around 70% prior to the installation of pressure oxidation to above 84%. The project has increased the nominal gold output at Macraes from 120,000 oz/y to 170,000 oz/y. On-going plant optimisation for process parameters is discussed, giving rise to flexibility in gold production, with key controlling parameters exceeding design.

Jan 1, 2000

The principal activities of the Bureau of Mines Explosives Research Center during fiscal year 1967 (July 1, 1966, to June 30, 1967) arc reviewed in a part 1. Part 2 presents short abstracts of the publications issued during this period in the Bureau series and in other media. Part 3 describes a short study on the shock initiation of hydrogen peroxide not destined for publication elsewhere. ACKNOWLEDGMENTS The Bureau of Mines gratefully acknowledges the support received through cooperative agreement in fiscal year 1967 from The Dow Chemical Company Manufacturing Chemists' Association, Inc.

Jan 1, 1968

By T. Clarkin

This paper presents a hydrologic closure design concept to minimize the risk of water discharges from closed mine tailings facilities. It evaluates the applicability of U.S. Nuclear Regulatory Commission guidelines to develop acceptable designs for the closure of tailings facilities that have a calculated adequate surcharge capacity for environmental protection and an emergency spillway for dam safety. The guidelines provide a basis to estimate an acceptable surcharge capacity of a Probable Maximum Flood series for storage of surface runoff. To be conservative and for redundancy with respect to dam safety, an emergency spillway is provided to pass the Probable Maximum Flood. Depending on the annual water balance, the surcharge capacity may be used by surface runoff and minor amounts of sediment that accumulates in the impoundment from year to year. The emergency spillway crest is then set at this level or above the surcharge capacity, whichever is higher. An example is given of the active Red Dog Mine tailings facility in Alaska where this method was used for the preliminary design of the tailings main dam at its ultimate closure configuration.

Jan 1, 2012

By Mehdi Razavi

Scope of the Study The possibility and risk associated with mining two stopes at the same time The influence of Creighton Fault on the stability and dilution The effect of irregular shape of stope walls on overall stope stability and ore dilution The support requirements for proposed mining plan

Oct 1, 2010

By G. D. Schena, C Chiaruttini

The feasibility is demonstrated of reconstructing the volumetric distribution of liberated particles and middlings by use of a damped, weighted least-square regularisation method. This allows a precise mass balance to be obtained around a separation/concentration unit, permitting evaluation of the partition curve (Tromp curve) of the separator. Areal grade measurements are made on polished sections of feed, concentrate and tailings and a kernel-based inversion technique is then used to obtain the volumetric grade distribution of the three assemblages. A plain kernel (number of occurrences) and a weighted kernel (each occurrence counted with its area) are used for the solution. Testing of the method on computer-generated synthetic areal grade measurements indicates that it offers a valid alternative to the tedious conventional procedure of conducting experiments with heavy liquids

Jun 21, 1905

By T. Grammatikopoulos, A. McKen, O. Christiansen

Vanadium mineralization occurs in oxide-rich horizons within layered metagabbro zones of the Sinarsuk deposit, West Greenland. The main oxide minerals are vanadiferous magnetite and ilmenite, comprising 30% to 90% of the rock volume and the ratio of magnetite to ilmenite ranges from 3:2 to 4:1. Ore microscopy shows that magnetite and ilmenite vary between 0.2 mm and 4.5 mm in grain size, but locally they are coarser grained. Grains are subhedral to euhedral and annealed suggesting that they will liberate very well upon grinding. Electron microprobe analyses indicate that magnetite grains are homogeneous and have a vanadium content, in different mineralized samples, ranging from 1.93 wt% to 2.68 wt% equivalent V2O5. Ilmenite hosts abundant and variably sized hematite lamellae, and it has vanadium contents ranging from 0.32 wt% to 0.59 wt% equivalent V2O5. Preliminary beneficiation of two composite bulk samples shows the samples can be beneficiated fairly easily using low-intensity magnetic separation at a coarse grind (106 microns to 600 microns) to yield a vanadiferous magnetite concentrate. The presence of hematite lamellae in ilmenite prevents recovery of a satisfactory ilmenite concentrate. The most likely beneficiation flowsheet would encompass a primary mill (SAG or rod mill), which would grind to about 600 microns, followed by a rougher magnetic separation stage. The rougher magnetic concentrate would be reground in a ball mill until suitable liberation is achieved. The reground material would then be cleaned in further LIMS stages. However, further laboratory testing is required to establish the final beneficiation program. This work demonstrates the value of mineralogical investigation in guiding and explaining the results of beneficiation processes.

Jan 1, 2002

By R. G. Garrett, A. J. S. Geddes

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The 1986 geochemical survey was successful in recognising all the previously known mineral occurrences of significance in Jamaica, in outlining areas not previously believed to have mineral potential and in stimulating fresh appraisals of old occurrences in terms of their potential for new commodities. This has resulted in a very significant increase in mineral exploration activity in Jamaica

Jul 1, 1991

By K. T. Menzies

This report documents laboratory and in-mine analyses of diesel exhaust pollutants carried out to assess the fate of potentially reactive species in the mine environment. Specifically, the concentration of stable compounds including carbon monoxide and carbon dioxide, and potentially reactive compounds including nitric oxide, nitrogen dioxide, sulfur dioxide, aldehydes, formaldehyde, acrolein, formic acid, odorants, particulates, soluble sulfates, and polynuclear aromatic hydrocarbons were determined. The concentration and mass emission rates of these compounds were measured in the laboratory under three engine speed and load conditions and with three exhaust control conditions, i.e., none, catalyst, water conditioner. Once calibrated, the engine was installed in the Bureau of Mines Safety Research Coal Mine and the concentration of exhaust pollutants measured at several distances downstream (inby) of the engine. Laboratory results confirm the relatively small effect of exhaust control devices on most pollutants under engine conditions of low speed and load. At higher engine speed and load, the catalyst is more effective in controlling many pollutants. The in-mine data indicates that during residence times, which are typical for miner/exhaust contact, most diesel exhaust pollutants do not decrease in concentration. The obvious exceptions are nitrogen dioxide, sulfur dioxide and formaldehyde. The concentration of these pollutants is reduced by up to 75 percent in five minutes. The lack of increase in levels of obvious reaction products indicates that surface loss may be a major sink for these pollutants.

Jan 1, 1980

By Joseph A. Vanous

The inductive communication system was developed under this contract for use in the hoist of deep mines. This program was a four phase program with experimental dual frequency equipment resulting from Phase I, emergency single frequency equipment developed under Phase II, and equipment documentation required under Phase III. An additional emergency system was provided under Phase IV.

Jan 1, 1976

This paper describes a proposal to reopen the Sylvia gold mine for underground exploration and development for an initial production of 10 000 tpa. A combination of trackless mining equipment and railtrack would be utilised for development with ore extraction being carried out by undercut and fill methods. The use of the smallest LHD units for mucking, and rail track for the main haulage together with airleg drilling will form the basis for development and stoping. The proposal has been subjected to an environmental impact assessment report to evaluate the impacts of the proposal on the natural and social environment in the area.

Jan 1, 1987

By Jean Cayouette, Paul Blatter, Paul Cousin

"The Laronde mill was commissioned in 1988 and has been treating the Laronde Penna ore since 2000. The Laronde plant, situated in the Abitibi region of Quebec, has experienced mill expansions to accommodate 7500 mtpd and to recover gold and silver as well as important amounts of base metals (Cu, Zn, Pb). Ten sequential metallurgical and environmental processes are responsible for metals recovery and process viability. Over 200,000 ounces of gold, 4,5 million ounces of silver, 7000 tonnes of copper, and 78,000 tonnes of zinc are produced annually.In 2008, the Goldex plant began trucking high grade (35-45 g/t Au) pyrite sulphide concentrate (TCGO) for gold extraction at a newly constructed treatment plant, increasing gold output at Laronde by 40,000 ounces. In 2009, the high gold grade Lapa ore processing facilities were annexed to the Laronde plant increasing output by 120,000 ounces of gold. TCGO and Lapa productions are forecasted until 2018 and 2015 respectively, with known reserves of each mine.Today, up to 140 permanent employees run and optimise the Laronde plant operation. As a result, Laronde has intricacies intrinsic to a large and varied operation. The paper will outline the metallurgical highlights, challenges, and future outlook related to the treatment of each ore type (Laronde, TCGO, and Lapa).INTRODUCTIONFollowing the 2000 to 2003 expansions, the Laronde plant evolved into a mature milling complex with developed processing, man power, and water treatment capabilities able to accommodate the complex Laronde ore. The ore requires a series of grinding, copper/lead flotation and separation, zinc flotation, zinc tails precious metals leaching, followed by a counter-current decantation circuit and Merrill Crowe precipitation. A paste backfill and SO2-air cyanide destruction operate intermittently. The tailings area has a dedicated cyanide destruction and metals precipitation plant prior to water recycling to the mill. A biological water treatment plant was put into service in 2004 to address the build-up of thiocyanate in the tailings ponds at Laronde. This was the result of the high sulphide content of the Laronde ore and 90% recirculation of the process water. The plant uses bacteria to oxidize and destroy thiocyanate, and removes phosphate from the water before it is released to the environment."

Jan 1, 2011

By P. R. Day, W. K. Webster

"The introduction of large boreholes underground initially involved taking the techniques of open-pit bench blasting to the production stope, but with deeper boreholes and narrower stopes more controlled techniques must be developed in order to maintain good stope walls and prevent dilution of ore or structural damage to pillars due to blasting overbreak. The points discussed are drilling accuracy and drill pattern, the relationship between open-pit wall control and underground mining, the varied explosives products and initiation devices available, and some of the many ways that variations in loading, such as deck charging, etc., can produce desirable results.IntroductionThe use of large-diameter blastholes for underground mining began ten years ago and today they are widely employed in a variety of orebodies and stope configurations. These big blastholes, which range in size from 4.5 to 8 inches in diameter, were originally employed in the same manner ' as open-pit bench blasts; that is, the stope was silled out to full width and all holes were drilled vertical and parallel. This was suitable for competent, massive orebodies, however the popularity of the big drills saw their usage in more narrow stopes, often with poor ground conditions. The dipping orebodies and small drill sublevels resulted in inclined drilling.Today, there is full-ring drilling of 4.5-inch holes. Some 6.5-inch holes are drilled up to 350 feet deep. A 350-foot borehole may contain 6000 to 7000 pounds of explosive. The detonation of this size of charge weight within the confines of an underground stope can have considerable effect on the stability of stope walls and adjacent pillars. Obviously, precautions must be taken to minimize the damage which would result from the large charge weights possible with these big boreholes."

Jan 1, 1982