Search Documents

By Anja Pfennig, Thomas Böllinghaus, Marcus Wolf

During CCS components are exposed to a corrosive environment and mechanical stress which results in corrosion fatigue and is inevitably followed by the lifetime reduction of these components. The lifetime reduction of the cyclically loaded high alloyed stainless injectionpipe steel AISI 420C (X46Cr13, 1.4034) constantly exposed to highly corrosive CO2- saturated hot thermal water is demonstrated in in-situ-laboratory experiments (T = 60 °C, brine: Stuttgart Aquifer, flow rate: 30 l/h, CO2) in an environment similar to the on-shore CCS-site in the Northern German Bassin. In-situ tension-compression experiments were established simultaneously along with electrochemical measurements using a newly designed corrosion chamber in a resonant testing machine at a frequency as low as 30 – 40 Hz. In addition technical CO2 was introduced into the closed system at a rate close to 9 L/h. S-N plots, micrographic analysis and surface analysis of the fracture surface are demonstrated. X46Cr13 (surface roughness Rz = 4) reached the maximum number of cycles (12.5 x 106) at stress amplitude of 173 MPa producing a low scatter range of 1:3.5. Hydroxide and siderite layers were found on pits and crack surfaces. No typical fatigue limit exists. Pit corrosion prior to crack initiation may be identified as failure cause.

Jan 1, 2016

By Chuanfu Zhang, Jinliang Wang

"Brickless reaction shaft is the latest progress for flash smelting furnace. However, there are many factors influence the melting point of the freeze slag inside brickless reaction shaft, and their variational regularities are not obvious, thus, it is difficult for conventional methods to analyze accurately the complex data. In this research, the experiment data of slag melting point were processed based on optimal discrimination plane. For this method, two orthogonal vectors were firstly built up based on the Fisher's criterion, and then the experiment data were projected onto the two vectors, thus, two-dimensional feature vectors were extracted as criteria to determine the factors effect degree on the slag melting point. Results show that the CaO content is the greatest factor to the melting point of the freeze slag inside brickless reaction shaft, the content of Fe3O4, SiO2, Cu2 O and MgO is the second, and the FeO content is the last.IntroductionBrickless reaction shaft is the latest progress of flash smelting furnace reaction shaft. To research the influence factors on the slag melting point inside the brickless reaction shaft is significant to form freeze slag with compact structure, good heat insulation, certain intensity, appropriate thickness and reasonable distribution, to extend furnace life, to reduce energy consumption, and to promote safe production.However, due to the complex components, there are many factors influence the melting points of the freeze slag inside brickless reaction shaft, and their variational regularities are not obvious. Therefore, it is difficult for conventional methods, such as variance analysis, data fitting, etc., to analyze accurately the complex experiment data.Pattern recognition can easily classify information, even if there are many influencing factors. For pattern recognition, there are some sub-disciplines such as discriminant analysis, feature extraction, error estimation, cluster analysis (together sometimes called statistical pattern recognition), grammatical inference, parsing and matching (sometimes called syntactical and structural pattern recognition) [1, 2]."

Jan 1, 2012

By Achilles J. B. Dutra, Carlos M. Juarez

"The use of thiourea as a gold leaching reagent has been extensively studied by many researchers, and it has proved to be promising for some cases as refractory ores. Otherwise, the recovery of gold from these solutions did not receive so much attention. In this paper the electrowinning of gold in acidic thiourea solutions was studied by voltarnmetry and chronopotentiometry. An adsorption step was detected prior to Au(I) reduction and the diffusion coefficients at 25°C for Au-TU complex and FD were found to be 1.00 x 10.5 cm2 S-I and 1.98 x 10-5 cm2 S-I respectively. At -0.350 V (SCE) a passivation probably due to TU adsorption was observed. For higher overpotentials hydrogen evolution was the main reaction.IntroductionThe use of acidic thiourea solutions for the extraction of gold and silver has shown to be a promising alternative to the traditional process of cyanidation, specially for certain refractory ores (1-3) and electronic scrap (4). In some cases, the industrial scale was reached (1,5). The thiourea leaching of precious metals presents advantages over cyanidation, as faster kinetics, lower toxicity and lower sensibility to base metals; however the costs due to high thiourea consumption impairs its use.The majority of the publications on thiourea processing of gold is on leaching. Many are review papers (5-7). Recently, the adsorption and desorption of the gold-thiourea complex on activated carbon and ion exchange resins have been studied (8-11).Little research has been done on the electrowinning of gold from acidic thiourea solutions, most of it has been carried on the seventies and beginning of the eighties in the former USSR (12-17) and concerned the eletrolytic extraction of gold in tridimensional cathode cells.The present paper concerns the cathodic behavior of the gold-thiourea complex in the presence of formamidine disulfide in order to provide information on the electrowinning of gold from solutions obtained directly from leaching or from an elution process."

Jan 1, 1997

By Kafui Nyavor

Acid mine drainage (AMD) is presently the biggest single environmental problem facing the mining industry. New and expanding metal mines in most parts of the world have to demonstrate their ability to contain this problem to obtain operating permits. Conventional methods of controlling acid mine drainage have primarily been limited to collecting the drainage and neutralizing with alkaline materials which do not provide a permanent solution to the AMD problem. Since acid mine drainage results from the oxidation of sulfides in the presence of oxygen, water and iron-oxidizing bacteria, controlling any of these three factors contributing to pyrite oxidation provides a potential at-source remedy for reducing or preventing acid mine drainage formation. Physical properties such as hydrophobicity also play an important role in the attachment of bacteria, adsorption of oxygen, water, and other ions that subsequently lead to the oxidation of pyrite. In this communication, the suppression of pyrite oxidation by treatment with fatty acid amines (FAA) was investigated. The FAA treated pyrite samples were tested at various conditions of temperature and pressure. At an elevated oxygen pressure of 500 psi and a temperature of 600 C, less than 0.2% oxidation was obtained for the FAA treated pyrite samples, while over 1.2% oxidation was obtained for the untreated samples in 10 hours of oxidation time. Accelerated column oxidation tests at ambient condition showed that FAA mated samples reduced pyrite oxidation by at least 75% in 81 days.

Jan 1, 1994

By Youn-Bae Kang, Jong-Jin Pak, Min-Kyu Paek

The critical evaluation and thermodynamic optimization of Mn-Si-C and its sub-binary systems have been carried out over the whole composition range from room temperature to above the liquidus temperature. The solution properties of the liquid systems have not been clearly described because the liquid solution exhibits a high degree of short-range-ordering. In order to predict the thermodynamics of the liquid solution, the liquid phases were optimized by the modified quasichemical model. The model parameters of the solid phases were also optimized by the compound energy formalism to best reproduce the phase diagram and important thermodynamic properties in Mn-Si-C system. Using the model parameters, various thermodynamic calculations were carried out. The present database will be a part of larger thermodynamic database for the ferromanganese alloy database.

Jan 1, 2014

By Arsenio Enriquez, Adrian Deneys

"Rio Tinto through its subsidiary Kennecott Utah Copper Corporation (KUC) and Praxair have implemented the CoJet® gas injection system for copper anode refining. The system provides the capability to melt on average 60 to 70 tons of scrap copper per heat (with acceptable NOx emissions). The system has demonstrated the potential for tuyere-less sulfur and oxygen removal using coherent jet technology.This paper describes the process concept, system development, laboratory testing, implementation, current operation and ongoing developments."

Jan 1, 2009

By A. Christlo

Short circuit detection in 1984 involved nine inspectors for production rates of 43,000 tpa. Trials indicated the feasibility of applying cell voltage monitoring to short circuit detection and improving operational efficiency. A computerised cell voltage monitoring system was commissioned in February 1986, to read voltages from 648 cells. The system incorporates 16 evenly distributed work face units which communicate with a central computer system. Provision has been made in the computer program for the automatic adjustment of cell reference voltages. This allows for the effect of polarization and other process variables which might other wise interfere with short circuit detection. The work face units can continue to work independently for several days should this become necssary. Current efficiencies have been maintained and the number of inspectors reduced from nine to five.

Jan 1, 1987

By J. Méndez-Nonell

The thermodynamic and chemical properties of SrSO4 and SrS in a gaseous flow of CO and CO2 at high temperature are discussed. The thermodynamic analysis of the system was made using data from the literature. The results obtained from the thermodynamic analysis were experimentally verified using the thermogravimetric technique. The experimental results suggest the formation of a complex compound between SrO and SrSO4. It was also found a change in the chemical mechanism of the process between SrSO4 and CO-CO2 and in the chemical mechanism of the process between SrS and pure CO2.

Jan 1, 1995

By Craig A. Johnson

Cyanide speciation and behavior have been examined at three active heap leach operations, three heaps undergoing rinsing, and three sites with cyanide contaminated groundwater, all in the southwestern U.S. Data from these studies demonstrate that strong cyanometallic complexes of iron and cobalt can play ?an important role in cyanide behavior throughout the lifetimes of heap leach operations. In active circuits, we find evidence that significant amounts of cyanide combine with iron and cobalt to form strong cyanometallic complexes, and that these species can be adsorbed, probably onto iron hydroxides, or precipitated as insoluble cyanometallic compounds. When spent heaps are rinsed, the release of this cyanide is likely controlled by the slow kinetics of desorption from, or dissolution of, solids that have gone largely uncharacterized. We find evidence that strong cyanometallic complexes can give rise to transient free cyanide in some settings by rapid photo dissociation where heap rinse effluent is exposed to sunlight in open channels or translucent sample bottles. Thus, these species can complicate the ,preparation of spent heaps for decommissioning, even where regulatory standards ?are based on weak acid dissociable cyanide. There is a critical need for information on the form and stability of adsorbed and precipitated cyanide in spent ore heaps, on the concentrations of strong cyanometallic complexes in mineral processing effluents -particularly the complexes of cobalt, and on the natural attenuation of iron and cobalt cyanometallic complexes in both surface and subsurface waters.

Jan 1, 1998

By Ximeng Zhu

The electrochemical behavior of mineral and coal pyrites in stirred and quiescent alkaline boratelsulfate solutions @H 7.9-10.5) have been investigated using cyclic voltammetry. Significant differences in the electrochemical response of these pyrites were observed. At the mineral pyrite surface, three anodic peaks at about -0.8 V, -0.1 V and +0.5 V (SCE) have been detected along with their corresponding reduction peaks. The first two peaks correspond to FeIFeOI) and FeOI)lFe(III) oxidation. The third peak is present for quiescent conditions but disappears as a distinct peak when the electrolyte is stirred. In the upper voltage region +0.30V (SCE), the current increases markedly during stirring and the reactions correspond to the oxidation of pyrite with the formation FeOII) oxides plus elemental sulfur. Also there is evidence that Fe oxy-ions form. Coal pyrites, under rapid sweep conditions display only the first two anodic peaks, the associated reduction peaks and an additional reduction peak corresponding to one or more of the high voltage oxidation products. After prolonged exposure to high potentials, coal pyrite displays reactions similar to those of mineral pyrite but at much higher current densities demonstrating the much higher reactivity of the coal pyrite. The reactivity sequence was Upper Freeport coal pyrite > Pittsburgh coal pyrite > mineral pyrite.

Jan 1, 1991

By M. Girgis

The behavior of arsenic III during electrolytic refining of copper in acidic copper ?sulphate electrolytes was studied by different electrochemical methods such as, linear potential sweep, cyclic voltammetry, chronoamperometry and chronopotentiometry. The study showed that arsenic behaves as a depolarizing ion and has a deleterious effect on copper deposit. Three substrates; Pb, Cu and Ag were used during the refining process and the electrode kinetics were found similar for both Cu and Pb electrodes while a little difference was found for the Ag electrode. A microscopic study by scanning electron microscope was undertaken to show the influence of arsenic on deposit's morphology. Surface analyses of the deposit were carried out by some electronspectroscopic techniques such as Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS). The results showed that arsenic coexists with copper deposit at potential?~ -0.25 V.

Jan 1, 1987

By R. E. Burleigh

'Gold-telluride mineralization was deposited in quartz veins which cut a Late Cretaceous tonalite pluton emplaced near the southern margin of the Peninsular tectono-stratigraphic terrane in south-central Alaska. The gold-bearing veins formed shortly after the development of a widespread Cu-Mo sheeted quartz vein system. Early mineral assemblages consist of quartz, white mica, pyrite, and arsenopyrite (wall rock only). Subsequently, pyrite. sphalerite, chalcopyrite, zoned tetrahedrite and gold precipitated within multiply fractured veins. Late stage galena, tellurides (altaite, nagyagite, coloradoite), and Pb-Sb or Pb-Cu-Bi sulfosalta with gold constitute bonanza ore assemblages that are variably associated with quartz, white mica, ankerite, and calcite. Fluid inclusion evidence coupled with mineral assemblage paragenesis suggests the depletion of volatiles (C02, H2S) and cooling resulted in the precipitation of high grade gold mineral assemblages.

Jan 1, 1988

By Stephen K. Pave1

Over 1,100 tons per day of Fluid Catalytic Cracking Unit (FCCU) catalyst is used worldwide. During the cracking reaction, catalyst is contaminated by deposited metals including nickel, vanadium, potassium, copper, iron, sodium, etc. To compensate for contaminants, a portion of the circulating catalyst inventory is withdrawn for disposal and fresh catalyst is added. The DEMETR process takes spent FCCU catalyst and removes a portion of the metal contaminants, enabling the refiner to recycle demetallized catalyst, thus reducing the solid waste from the refinery. Through August, 1993, the operation of one unit for one refiner has resulted in the recycling of over 7,500 tons of spent catalyst.

Jan 1, 1994

By Russell E. Clemons

Coarse-crystalline granite, quartz syenite, syenite, meladiorite, and anorthosite in the Florida Mountains, southeast of Deming, New Mexico, were originally mapped as Precambrian. They were remapped in 1971 and some of them described as Mesozoic intrusives. Several subsequent papers presented Precambrian and Ordovician ages. Zinc, lead, copper, silver, gold, manganese, fluorite, and barite mineralization in the Florida Mountains invite more extensive exploration. Clarification of ages of rocks and periods of alteration and mineralization are necessary for efficient exploration. Field observations combined with petrographic studies strongly suggest that all the coarse plutonic rocks are Precambrian and most were altered extensively by late Tertiary hydrothermal activity.

Jan 1, 1982

By Rak-Jun Choi

Plasma-induced damage of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) has been studied in terms of forward turn-on and reverse breakdown voltages, together with etch rate and surface morphology. The physical degradation of sidewall along with rough surface morphology of n-GaN caused by increased ion scattering induced the deterioration of the forward and reverse voltages. It was found that the turn-on voltage is sensitive to the surface roughness of the etched n-GaN and the breakdown voltage is strongly affected by the sidewall contamination. Annealing under nitrogen after the mesa etching improved the electrical properties of the InGaN/GaN MQW LEOs. Efficient blue light-emitting diodes (LEOs) were fabricated using InGaN/GaN triangular MQWs. The LEOs with triangular QWs showed a lower operation voltage and 2.4 times higher light output power than those with the rectangular MQW LEOs at 20 rnA and 20 "C. The intensity of electroluminescence (EL) at 20 mA was almost independent of ambient temperature in the triangular QW LEO, but decreased substantially in the rectangular one.

Jan 1, 2003

By J. C. Yannopoulos

The quest for a continuous copper smelting and converting process, which has been going on for a long time, has not as yet reached its objective. The most recent efforts for the development of a continuous copper?making process started about two decades ago. Among the contending proposed processes, four have been piloted and three of them are currently in operation: the WORCRA process., the NORANDA process, the MITSUBISHI process, the OUTOKUMPU process. The WORCRA process, after some long pilot plant tests, failed to develop as an industrial process: The NORANDA process, as currently operating, is a smelting process and not a continuous copper?making reactor as initially conceived. The MITSUBISHI, although the only continuous process, has not been widely accepted. The OUTOKUMPU process can be applied only to a low iron concentrate feed and co?produces blister and high in copper slag. The thermodynamics of these "continuous" systems and the practical problems of their industrial application are reviewed and discussed. The achievement of efficient and inexpensive environmental control should' be the primary objective of any new process development. A review of the environmental problems of the copper industry indicates that the quest for a continuous smelting and converting furnace should be intensified.

Jan 1, 1983

By Bin Xu, Qian Li, Yong-bin Yang, Tao Jiang, Jian-jun Hu

It could significantly increase the leaching rate of refractory gold concentrate containing sulfur and arsenic by roasting pretreatment with adding certain amount of sodium sulfate, and the mechanism of that was systematically researched with DSC, XRD and SEM in this paper. Results indicated that the mechanism of Na2SO4 on double refractory gold concentrate at roasting pretreatment can be summed up in the following three aspects：Firstly, Na2SO4 can react with SO2 and SO3 which is produced by the oxidation of sulfides and generate Na2S2O7(l), which plays buffer effect on sulfides exothermic oxidation, avoiding the secondary-encapsulated of gold. Secondly, the liquid phase of Na2S2O7 can cover mineral particles' surface that possesses a sintering effect, it leads to internal cracks of the particles. Finally, mineral particles will gather with sodium sulfate particles as the center that can improve the permeability of the layer.

Jan 1, 2015

By A. E. Isaacson

The U.S. Bureau of Mines is studying the effect of supercritical water, at 400' C and 3,500 psi, and subcritical water, at lower temperatures and pressures, on mixtures of minerals and metals to determine the possible applications of water at high temperature and pressure for processing these materials. This research was conducted using a flow-through bench-scale system. Copper-bearing minerals studied were chalcocite, chalcopyrite, covellite, and cuprite. In general, mixtures of copper minerals and pyrite reacted to form bornite. Intermediate phases formed were chalcopyrite and digenite. Similar reactions occurred between pyrite and metallic copper. A mixture of chalcopyrite and pyrite was inert in supercritical water'. The reaction between cuprite and metallic zinc yielded metallic copper. The cuprite was reduced by hydrogen generated by the reaction between metallic zinc and water. None of the reactions occurred exclusively in supercritical water, but also occurred in water at high temperature and pressure below the critical point. 'Experimental results did show that a dual-reaction process, consisting of solid-state diffusion and fluid transport, was occurring.

Jan 1, 1989

By R. D. Irwin, W. M. Mullins, E. A. Medina

"Various stability criteria are introduced and thermo-kinetic models for metallurgical processes are used as concrete examples for evaluation. Kinetic criteria for the process of dynamic recrystallization are proposed. These criteria are compared to the non-equilibrium thermodynamic approaches discussed in the literature. The application of macroscopic stability criteria to materials processing is then discussed.IntroductionThe mechanical behavior of metals at elevated temperature is very well predicted by any of several empirical constitutive relations. Typical is the power-law (or Swift's) form,Equationwhere r-is the stress, y is the strain and m, n , t0, y0 and Q are material constants. This form has been used with some success in the metals processing area [1]. In general, though, all of the empirical constitutive equations are static, failing to account for any dynamical properties of the system they seek to describe.The physics of warm deformation is qualitatively well understood. An example is power-law creep, where the dominant mechanism is assumed to be lattice diffusion limited climb of dislocations, which allows the strain-rate to be determined by the applied stress through"

Jan 1, 1997

By J. L. Jambor, H. W. Nesbitt

Oxidative dissolution of pyrrhotite and pyrite is largely responsible for the sulfate-rich waters of the vadose zone in the Waite Amulet tailings. Although the shallowest of the sulfate-rich waters are of the Fe-SO4 type, they change to Mg-SO4-type, near-neutral waters within 1-2 m of the tailings surface. Phyllosilicates and amphiboles are the only minerals present in sufficient quantity to ameliorate the amount of acidity produced. X-ray diffraction and microscopic studies of bulk sample indicate that quartz, chlorite, talc, amphiboles, magnetite, albite, and micas are the major and minor non-sulfide minerals, but their variations with depth do not give clear indications of depletion in the vadose zone. Mineralogical and bulk chemical compositions of the tailings confirm that Fe2O 3 has accumulated in large quantity in the vadose zone, with the Fe having been derived from Fe sulfides. When the effect of Fe2O3 is accounted for, the bulk compositions suggest that SiO2 is slightly more abundant in the vadose zone than in the saturated zone. This may be the result of residual enrichment of siliceous minerals such as quartz and albite in the vadose zone. Weathering of the tailings since the cessation of deposition in 1962 has resulted in a well-defined zone of sulfide depletion and secondary sulfate-mineral development. Although some silicate dissolution is indicated by pore-water compositions, the role of silicates in providing neutralization seems to have been minimal. The contribution by silicate minerals in laboratory tests of neutralization potential may be excessive relative to that in natural settings.

Jan 1, 1999