Search Documents

By WenCai Li, Yong Ren, Shuai Niu, Xin Hong

"Temperature measurement is very important in metal smelting process. Many devices are used to realize non-contact temperature measurements. Compared to conventional thermocouple, infrared temperature measurement has it's unique advantages. However, using an infrared temperature measurement at the top of the furnace can not obtain the desired optical signal because of disturbance from slag layer, high-temperature gases and other effects. A real time thermometry system with dual-wavelength radiation was presented to get optical signal emitted from molten metal through bottom-blowing nozzle. Taking into account the advantages and disadvantages of bottom-blowing devices, a MHP (Multiple Hole Plug) bottom-blowing device was used, through which the optical signal was transferred to the infrared thermometer by use of optical fiber. After conversion and analysis in real-time, the result was displayed and recorded in computer. After calibration, it could be a good predictor of temperature trend in a metallurgical process. IntroductionAt the refining stage of steelmaking, in order to achieve predetermined chemical composition and temperature, high-temperature molten steel is refined in a furnace such as converter. Because the refining process involved with chemical components and reaction velocities in the furnace rely on the temperature of steel, it is necessary to know the temperature accurately in real time during the process. And temperature measurement is also helpful for the end-point judgment. The temperature in the refining process changes quickly, for instance, in a converter, 300t molten steel is processed in only about half an hour.At present, traditional way of temperature measurement is using a thermocouple probe mounted on a lifter called a sub-lance. The thermocouple is immersed in molten steel and its temperature is measured during the short period until the thermocouple is fused. Accurate and reliable temperature can be obtained by this method, but in consideration of the discontinuous measurement and the costs, missing the end-point temperature may sometimes occur.According to the above background, a method in which a temperature-sensing element such as a thermocouple is immersed directly in molten steel is not suitable for the continuous temperature measurement because materials having such stability are not available. Therefore, radiation thermometry is promising. There have been some reports on radiation thermometry through an observation nozzle through the bottom or side of a refining furnace [1, 2]."

Jan 1, 2014

By Yoshihiko Maeda

It is said that the 21st century will be an era of the remedy of the global environment. In order to reserve natural resources for the future and to avoid the dispersion of heavy metals after usage and to avoid pollution problems, it is extremely important to recycle heavy metals as much as possible by reasonable recovery procedures. The nonferrous metal industry is expected to play a important role in the recycling of heavy metals that are originally their products. From the depressed metal price experienced in Japan in 1980'h due to the sudden change in current exchange rate between US dollar and Japanese yen, one of major nonferrous metal company, Dowa Mining, has diversified its business area not only to the so-called down stream, but also to the environmental business including metal recycling, industrial waste treatment and soil remediation by utilizing technologis and facilities once used or still used for mining and smelting of copper, zinc, lead and precious metals. In this paper some of these applications will be presented.

Jan 1, 2003

By Hideki Yamamoto, Junji Shibata

"The chemical reactions of fluoride and chloride gases with metal chloride or metal oxide are utilized as an effective treatment for harmless disposal. These chemical reactions can be adopted in the temperature range of 80°C~400°C, which is lower than that in the combustion treatment (800°C). Reaction products are metal fluoride or metal chloride which are a harmless and a valuable chemical material as one of new resources. This paper, concerns with a new harmless disposal treatment of toxic global warming gases.IntroductionNew technology to make fluoride and chloride gases such as NF3, CF4, SF6 BF3, Cl2 and BCl3 harmless has been developed and a new concept on the removing toxic gas to be used in the advanced process of materials has been established. The fluoride gases ~re toxic and special type of gases to be used in the process of manufacturing semiconductors and their specific applications include the dry etching of semiconductors, cleaning of CVD systems, an oxidation agent for rocket fuel etc. Especially, NF3 is also attracting an attention as a high-energy source for chemical laser systems. As a fluoride gas like NF3 is, however; toxic and highly stable chemically, if discharged into the atmosphere, it is liable to cause far-reaching adverse influences on global warming in the same manner as carbon dioxide gas and feron gas.Up till now, the combustion treatment method has been adopted for the disposal of the gas, and when treating the gas by high-temperature combustion (800""C), the generation of nitrogen oxides (NOx), sulfur oxides (SOx) and hydrogen fluoride (HF) have been confirmed: These chemical substances are not only linked with an intense c0rrosion of the combustion systems but also create the generation of atmospheric pollution and acid rains, and therefore, constitute a serious social issue."

Jan 1, 2000

By W. Dutton, D. Simms

"The clearing of tuyeres on copper and nickel converters or similar metallurgical, vessels has, for many years, been done using mainly a manually- operated ""puncher"". One such device is the ""Gaspe Puncher"" developed in 1962 at Noranda's Gaspe Smelter. In an attempt to remove the operator from the cab of the Puncher, and to relieve him of a tedious, uncomfortable job, Noranda's Horne Division, in cooperation with Heath & Sherwood (1964) Limited and the Noranda Research Centre, undertook to automate the Gaspe Puncher used on the Noranda Continuous Smelting Process Reactor.The automated puncher is controlled by a Texas Instruments Model 530C Programmable Controller (PLC). Position measurement and control is done using non-contact position measuring equipment from the Tele-Controls Division of Geodimeter Inc. The entire automation system was installed on an existing Gaspe Puncher with minimum disruption to the operation of the smelting process. The operator's panel allows the user to ""block out"" any individual tuyere, and to select any of a variety of operating modes.The development of the automated puncher is described, and the results of several months operation are given.IntroductionThe tuyeres of copper and nickel converters and similar metallurgical vessels become blocked with solidified material formed by the cooling action of the blowing air. This restricts the converting operation. Clearing these blocked tuyeres has for many years been done mainly using a manually-operated ""puncher"" which uses a hydraulic or pneumatically-operated piston to drive a steel bar into the tuyere. The Gaspe Puncher, developed at Noranda's Gaspe Smelter in 1962 is one such device. It is currently being built and sold by Heath & Sherwood (1964) Limited, under license to Noranda. There are over 200 units in operation world-wide.In an attempt to remove the Puncher operator from the cab of the Puncher, and to relieve him of a tedious, uncomfortable job, and to increase productivity, Noranda's Horne Division, in cooperation with Heath & Sherwood (1964) Limited and the Noranda Research Centre, undertook to automate the Gaspe Puncher used on the Noranda Continuous Smelting Process Reactor. This paper describes the development of the automated Gaspe Puncher, its installation at the Horne Smelter, and the results of its operation after several months."

Jan 1, 1989

By Xi-Shan Li, Qian Li, Yong-bin Yang, Li-na Cui, Tao Jiang, Jie Ge

"With regard to control environment pollution in the roasting pretreatment of sulfur & arsenic-bearing gold concentrate, roasting of double-layered pellet was proposed. In the paper, the characteristics of double-layered pellet roasting were studied. Removal and solidification rates of sulfur and arsenic were investigated as primary factors. The result indicated that the removal and solidification rates of arsenic reached up to 95.91 % and 98.95% while the sulfur was 97.19% and 97.90% respectively on the premise of adopting slaked lime as solidified agent at temperature of 6000, the package proportion of 2.14 and roasting time of 3h. However, pyrite and arsenopyrite were transformed to hematite and magnetite and product of solidification mainly consisted of calcium sulfate, calcium arsenate and calcium sulfite within optimum roasting parameters.IntroductionUtilization of refractory gold resources has been gradually concentrated on with the depletion of the gold resources which are easy to deal with in the world [1]. Sulfur and arsenic-bearing gold ore is a typical refractory gold one, in which ultrafme gold is encapsulated in the structure of metal sulfide minerals [2,3], so it gives poor recovery through direct cyanide leaching. These refractory ores need pretreatment before the process of cyanide leaching to undermine lattice structure of pyrite and arsenopyrite containing gold [4] so that the gold could touch with cyanide solution [5]. Among various methods of pretreatment, conventional roasting method is most effective, but this process generates gases such as S02 and As203 harmful to environment. Therefore solidification roasting was proposed to solve this problem occurring in the conventional roasting at the end of last century."

Jan 1, 2013

By Miguel Olivas-Martínez

A two-dimensional computational model for the hot filament chemical vapor deposition (HFCVD) process to produce diamond films is presented. The model incorporates the transport of momentum, energy, and mass inside the reaction chamber of a HFCVD reactor. The gas-phase homogeneous reactions were represented by a simplified reaction mechanism. The gas-phase transport equations were coupled to the kinetic expressions representing the catalytic dissociation of the molecular hydrogen at the filament surface and the deposition rate of the diamond film on the substrate. The computational model was solved numerically by means of a commercial software. The model predictions showed good agreement with the experimental data reported in the literature in terms of both temperature and methyl concentration profiles along the filament-substrate center distance. Examples of the potential applications of the present formulation for the design and further optimization of the HFCVD reactor are discussed.

Jan 1, 2006

By N. R. Green, N. J. Humphreys, D. McBride, T. N. Croft, M. Cross, D. M. Shevchenko

"Centrifugal casting offers a route to high quality products in difficult to cast high temperature low superheat alloys and thin section molds. Under centrifugal forces metal is forced into thin sections and can fill thicknesses of less than a millimeter. However, due to the high liquid metal velocities there is a high risk of surface turbulent flow and air entrainment within the liquid metal. The combination of interacting flow-thermal-solidification phenomena and associated defects is a challenging modeling task which the authors have previously described and validated. Capturing the metal-air interface, on what are inevitably complex three dimensional geometries, results in highly computationally expensive simulations and simulating a single cast can take weeks on a single processor. This contribution reports on modeling a complex centrifugal cast, gas entrainment, bubble transport and solidification, employing meshes of up to a million elements and investigates the scalability of the model on high performance clusters.Introduction The ultimate goal of any casting procedure is to produce a defect-free product. For difficult to cast alloys, such as Titanium, centrifugal casting has a number of advantage over conventional gravity methods [1]. In the casting of thin sections, such as turbine blades, the metal is forced into the thin sections under centrifugal forces. The centrifugal force can overcome the backpressure due to surface tension and the metal can fill mould sections with thicknesses substantially less than a millimeter. However, the materials used in these castings [2] tend to be highly reactive and requires low superheat. High liquid metal velocity gives rise to a high risk of free surface turbulent flow and of associated entrainment through free surface turbulence [3] and trapping of gas present in the flow [1]."

Jan 1, 2012

By Kazuya Koyama

The leaching of copper from a printed circuit board (PCB) and the electrodeposition of copper from a cuprous solution in ammoniacal alkaline solutions were examined in order to develop an energy-saving hydrometallurgical process for copper recovery from electronic scrap. In the leaching experiments, copper in the PCB was oxidized by Cu(II), and Cu(I)-ammine complex ions were formed. The copper(I)-ammine complex slightly depressed the leaching rate, while Cu(II)?ammine markedly enhanced it. During the electrodeposition experiments, the current efficiency of copper deposition was approximately 100% in the current density range of 200 to 1000 Am-2. The electrodeposition of copper from the Cu(I)-ammine complex solution favored the production of plates rather than powders.

Jan 1, 2003

The resist profile simulation is carried out using the combined data obtained. The nematic liquid crystal is clear only when a long range order exists, in the whole medium. using the Jones matrix method. Director can change from point to point and is, in general, a function of space. Details of the lens structure and of the devices fabrication and performance are described. Light from conventional light source or laser is passed through a polarizer and then incident on the specimen At the nematicisotropic, transition temperature, the medium becomes isotropic and looks clear and transparent. The transition can be approached by changing the impurity concentration or, indirectly, by tuning the temperature since the pinning strengths of the random and crystal potential have in general a different temperature dependence.

Jan 1, 2006

By Eiki Ono, Atsushi Yamatodani, Shigeru Sunagawa, Yasushi Takasaki, Atsushi Shibayama, Yasunori Higuchi

"During metallurgical processing of non-ferrous metals, smelting residue (inc. smelter slag, flue gas and so on) is inevitably generated as secondary product.In this research, some experimental feasibilities were investigated to recover/remove Cu and As from the residue. Primarily, the removal of As and volatilized materials from the residue was examined by pyrometallurgical treatment (dry-process). In the second stage after treating the residue with a dry-process, leaching and solvent extraction as hydrometallurgical treatments (wet-process) were also investigated by using H2SO4 solution as a two stage leaching treatment, to dissolve various metals from the leach residue. Then, solvent extraction was examined by using LIX-84I as an extractant to recover and separate Cu from impurities from the final (2nd) leached solution. For the leaching stages, the removal of 90 % As and the leaching rate of 85 % Cu could be achieved by 0.25 mol/l and 1.0 mol/l H2SO4 solution, respectively. On the other hand, the extraction of over 90 % Cu and stripping was carried out by solvent extraction. 1. IntroductionIn metallurgical process for non-ferrous metals, smelting residue (inc. smelter slag, flue gas and so on) is inevitably generated as secondary product, i.e., flue dust, slug and so on. The smelting residue includes some useful metals and undesired toxic materials; Cu, Pb, Ca and As, etc.In Japan there is one undisclosed place stockpiled with 10,000 ton of smelting residue from abandoned smelters about 25 years ago. Therefore it is necessary to reduce the residual amount for space and environmental protection including water treatment by separating and removing toxic materials."

Jan 1, 2008

By Roma T. Dec

Many industrial wastes may require preliminary processing to change their particle size, density, surface properties or flowability to become more suitable for treatment and recycle. This can be achieved by pressure agglomeration using roll presses. In the following paper an overview of various roll press processing methods like briquetting, compacting, compacting-granulating or densification is presented together with basics of process and equipment design. The emphasis is focused on major factors influencing compaction process and responsible for pressure build up and final product quality. Finally, two examples of roll press application for briquetting of steel plant wastes and compaction of alumina base catalyst tailings are introduced.

Jan 1, 1996

By Nobuhiro Ishikawa

The in-situ observation of the effect of impurities on the reduction process of iron oxides by C in TEM was carried out. A few wt% of CaO or AbO, was used as impurities in FeO was prepared. Some precipitates grew into the C layer expect for using 3.0wtCa. The reaction between FeO and carbon was much different from using pure FeO at about 800-1 lOOK. The rate of reaction became much slower including Ca and almost no reaction was happened with the concentration of CaO up to 3.0wt%. On the contrary, AbO, had ahuost no effect on the reaction. The results indicated that Ca suppressed the reaction and the effect of Al was much less. The precipitates which grew into C layer accompanied almost no Ca and AI. Only Fe was detected in the precipitates.

Jan 1, 2008

By W. G. Davenport

Chapter 6 examined autotherrnal smelting of pure chalcopyrite concentrate with 50 mass% O2-50 mass% N2 blast. It showed that production of 1500 K products with this blast requires: 181 kg of pure oxygen 337 kg of air per tonne, of concentrate. It also showed that the grade of matte produced with this blast is 58% Cu. This chapter re-examines autotherrnal smelting by asking: (A) WHAT COMPOSITION BLAST (MASS% 02 -MASS% N2), 298 K, WILL AUTOTHERMALL Y PRODUCE 65% Cu MATTE 1500 K FROM PURE CHALCOPYRITE CONCENTRATE? (B) HOW MUCH PURE OXYGEN AND AIR WILL BE NEEDED? These are important questions for flash? smelting because furnace operators usually want to send specific composition matte to converting. This chapter shows how a specified matte can be produced autotherrnally with 298 K oxygen-air blast. Later chapters show how it can be done with hot blast, hydrocarbon combustion, different concentrates etc.

Jan 1, 2001

By Hong Yong Sohn

On the occasion of this symposium in my name, I reflect upon the contributions of my academic mentors and early associates who helped shape my professional career. I was fortunate to have these people around me during my graduate work and at the start of my professional career. In forming my view of the technical field and career, they represented academia, research institutions, industry, and different parts of the world.

Jan 1, 2006

By Kang-In Rhee

Nonferrous metal recycling not only provides energy saving and environmental benefits but also is a significant factor in the supply of various types of metals used in our society. Recycling plays an important role in establishing the sustainability of materials. The total amount of recycled nonferrous metals by weight accounts for less than 5% but their value is larger than 50% compared to ferrous metal recycling which consists of about half of the total metal recycling in weight. This paper describes trends and typical achievements in nonferrous metal recycling and overviews the present and future of nonferrous metal recycling technology and business in Korea.

Jan 1, 2006

By John O. Marsden

The past fifteen years have seen a number of important developments in copper hydrometallurgy, including the commercial application of biological heap leaching of secondary (chalcocite-dominant) copper ores, the commercial demonstration of chalcopyrite concentrate leaching technology using pressure leaching and biological processes, and the application of novel configurations of solution extraction circuits. Significant emphasis is now being placed on the development of effective stockpile leaching practices for primary ores (chalcopyrite and bornite-dominant mineralization). Some of these developments have been highly successful, and will pave the way for further development and commercialization. Others have been less successful. These developments are reviewed in the context of the metal price cycle and trends for the future are identified.

Jan 1, 2006

By J. Michael Canty

Over 25 years of US research in Mineral Recovery from Geothermal Solutions have lead to few commercial applications. With the World Bank program in Kamchatka, Russia in September 2005 a step was taken to vitalize and coordinate the many efforts to advance economic mineral recovery systems worldwide. The US Department of Energy is helping to spur on the interest and research needed to realize the many benefits of extracting minerals from geothermal solutions. The excitement of recovery of minerals from geothermal brines has many positive angles. The economics of certain geothermal site is improved if a revenue is arrived from a sellable commodity with the geothermal power. The use of cleaner geothermal brines also improves the capable use of the brine before reinjection. We will review the history of Geothermal in the USA and the opportunities for recovery of different minerals and the markets for them.

Jan 1, 2006

By M. Olper, M. Maccagni, C. J. N. Buisman, C. E. Schultz

The key point of the CX-EWS process is the conversion of lead compounds, contained in the active mass of spent batteries, into lead sulphide. The obtained lead sulphide is leached with ferric fluoborate electrolyte to dissolve lead and oxidize the sulphur from sulphide to the elemental form. The lead-rich solution is fed into a diaphragm electrolytic cell depositing lead and regenerating ferric fluoborate. The introduction of sulphate reducing bacteria technology in the sulphidization step of the battery paste improves dramatically the economics of the CXEWS process, reducing the costs of chemicals, avoiding gypsum disposal and minimising the unit operations of the process. This paper describes in detail this technology change with reference to the economics of the process.

Jan 1, 2000

By F. San Martin, Y. Lefevre, F. Tamargo

The San Juan de Nieva smelter was commissioned in 1960 with an electrolytic zinc capacity of 15,000 t/y. After a number of minor expansions, the capacity was increased to 320,000 t/y in 1991 and will reach 440,000 t/y by August 2001. The expansion involves the construction of a 900 t/day Lurgi roaster and a new acid plant. The leaching will be fully revamped and modernised, including the construction of a new building for residue treatment and for j arosite precipitation with a separate circuit for silver-containing concentrates. The project also includes the construction of a fully automated 137,000 t/y zinc cathode tankhouse fitted with 3.4 m2 cathodes designed by Asturiana de Zinc, and based on the existing tankhouse and introducing some improvements. New melting and casting facilities, also designed by Asturiana, will be constructed.

Jan 1, 2000

By Julian Szekely

Transport phenomena, that is heat transfer, mass transfer and fluid flow, play a critical part in the operation of metallurgical reactors. In this paper, we shall present a review of our current state of ability to model these systems mathematically, with emphasis on the use of computational codes that are generally accessible to the public and on the comparison of the theoretical predictions with measurements.

Jan 1, 1993