Search Documents

By W. Pawlos, A. Bakalarz, M. Duchnowska

This paper presents the results of an investigation into the influence of hydrodynamics on a preflotation process for the copper sulfide ore from the Fore-Sudetic Monocline deposits in Poland in a flotation machine. The main aim of the preflotation stage for Polish copper ore is to remove the easy-to-float organic matter — organic carbon — that causes serious problems in metallurgical processes. The organic matter is connected with the presence of shale ore. This paper describes the preflotation experiments conducted to investigate the effect of various stirrer speeds. The upgrading selectivity of copper and organic carbon were analyzed and compared. The results show that the effectiveness of separation between organic carbon and copper decreases with increased stirrer speed in the laboratory flotation machine. The more intensive the mixing of the flotation suspension, the lower the selectivity of the preflotation experiment. Lower stirrer speed probably provides lower mechanical entrainment and flotation of copper minerals.

By Godfred Amponsah, Mehrdad Razavi

Slope failures very commonly occur during a long period of heavy rainfall and groundwater rise. The failures pose a substantial risk to people, infrastructure, and equipment downslope. In the recent past, the mining industry has faced an increase in tailings dam failure due to several reasons including pore pressure increases in the dams. Many failures have been observed to occur during times of water level fluctuations but the critical factors that influence the initiation of slope failures still need to be adequately clarified. To investigate these factors, laboratory experiments were conducted on model sandy slopes to determine pore pressure-induced slope failure initiation. This study also presents a method to examine water seepage through soil slopes using an ultraviolet (UV) dye and a UV flashlight. The small-scale model test simulation demonstrated failures induced by either water percolation from the upslope tank at a constant level or by raising the water level at intervals. A bottom chamber fully filled with water to replicate groundwater rise was also simulated. The soil slope was monitored at every stage to study the deformations and behavior until failure occurred. Results gathered from the controlled laboratory conditions were useful for the verification of the numerical modeling method created in the computer program Slide. The analysis showed that slope failure always occurred when the toe was fully saturated. High pore pressures and seepage forces reduce the shear force at the toe to almost zero causing it to slide. A comparison of slope height to water level also indicated an average of 96% water level to cause a failure. At this point, the soil slope is fully saturated and has no matric suction. The findings in this study show that, by monitoring the moisture content of slopes, failures can be predicted.

Feb 1, 2024

By Larry F. Brown

Mining has been the mainstay of the Woods Creek Valley for more than a century. The head of the valley is at the Continental Divide, about 50 miles west of Denver, Colorado. First, it was the quest for gold and silver that drew people to the valley. Then, when molybdenum was classified as a strategic metal by the U. S. Government during World War I, it was the valley's molybdenum mineralization which attracted the most attention. Molybdenum is used primarily as an alloying material in superior grades of steel. Circumstances responsible for providing the label "Urad" are unknown, but Urad is variously reported to be an acronym for "Uranium Research and Development" or "Uranium Research of America Division". The search for uranium was fruitless as no ore grade uranium exists in this area. The moly orebody was first developed and mined by the Primos Exploration Company from 1914 to 1919. During World War II, the mine was purchased by the government and turned over to the Molybdenum Corporation of America to operate. In 1963 AMAX Inc. purchased the property for $2 million. After spending nearly $30 million for exploration and development, AMAX put the mine into production again in 1967.

Jan 1, 1984

By Donald R. Williamson

Statistical studies at Cyprus Pima Mine indicate that samples from 22 blastholes are necessary for determining average copper grades, within a desired range of precision, for mine-model blocks by arithmetic averaging. The average number of holes in such blocks is 14. Many considerations show that more holes will not be drilled for sampling. A way to determine block grades more reliably than by" arithmetic averaging was sought. Thus far arithmetic averaging has proven to be the best procedure for the particular operation characteristics despite the small number of samples. It naturally follows that expenditure of great effort in sampling blasthole cuttings is unwise.

Jan 1, 1977

By Alan Boughey

The world's largest grinding mill operates at the Cadia Hill Mine in Australia. Svedala Industries supplied the 12.2-m- (40-ft-) diam, 20-MW Cadia gearless, semiautogenous grinding mill (SAG). This was a leap of more than 40% above the largest operating SAG mill. This article reviews the significant items involved in the development, design, manufacture, installation and operation of this mill. Description of the Cadia project The Cadia Hill Mine is located 25 km (15 miles) southwest of Orange, in the Central Tablelands of New South Wales, Australia. The mining lease covers about 3,100 hm2 (7,660 acres) of the Cadia Valley. The Cadia deposit is a large, homogeneous, low-grade, porphyry-type, gold-copper resource. Current reserves stand at 202 Mt (222 million st), grading 0.73 g/t (0.02 oz/st) gold and 0.17% copper. They contain 146.2 t (4.7 million oz) of gold and 347 Kt (382,500 st) of copper. The operation consists of openpit mining and ore processing to produce gold bullion and a gold/copper concentrate. The operation processes 17 Mt/a (19 millon stpy) of ore to produce 91 kt/a (100,300 stpy) of concentrate and 9.1 t/a (293,000 oz/year) of gold. The plant operates two 12-hour shifts a day and had a targeted availability of 94%. The plant facilities include a copper concentrator, o water supply system, an openpit mine, tailings pipeline and dam, and a concentrate pipeline and dewatering facility located in Blayney, about 35 km (22 miles) from the concentrator. Significant features of the process plant include o primary crusher and stockpile, a reclaim conveyor system feeding, the Cadia SAG mill (Figs. 1 and 2) and two 6.7-m- (22-ft-) diam ball mills (Fig. 3). A portion of the gold is extracted in a gravity circuit. The balance is extracted with the copper in the flotation section of the plant. Concentrate is thickened and piped about 35 km (22 miles) to the filter plant and rail loadout facility located in Blayney. Tailings are pumped to a tailings dam and process water is reclaimed from the tailings dam. The water system is designed to control and capture available runoff from local creeks, and to store these waters in dams and weirs. In addition, a major portion of the water for the process plant is treated effluent from the city of Orange and a smaller portion from Blayney Mill selection. The low-grade ore posed a dilemma for Cadia. To achieve a satisfactory economic operation, large-scale processing was required. The selection of the mills, equal to the largest designed and operated at the time, gave a plant configuration consisting of two 11.1- x 5.8-m (36- x 19-ft) SAG mills and three 6.1- x 9.1-m (20 x 30-ft) ball mills. This configuration did not provide the most satisfactory economic model for the project. A review of the single line configuration indicated that a significant reduction in the overall capital cost of the plant could be achieved by increasing the size of the mills and reducing the quantity. Increasing the size of the mills,

Jan 1, 2001

By John S. Carman

Our industry is in trouble. Real trouble. It has never been an easy, secure business. But to-day it is engulfed in revolutionary currents. No longer can there be reliance upon the checks and balances of market forces. Supply and demand largely dictated the economics of business enterprise in simpler days. To-day politics, in particular nationalism become increasingly dominant. And as governments expand and put out tentacles of interference in the direction of the mining industry, far too little understanding is evidenced as to how that industry works. Then there is something which is relatively new -stagflation. As the prices of minerals falls, the capital investment required for new extractive facilities soars at rates which far outdistance those which are cited by governments to indicate the magnitude of inflation. To illustrate; 1) In 1971 it was calculated that $355 million would be required to bring the Cuajone property in Peru into production. Five years later that stage was reached at a cost of $680 million. 2) With the Caridad mine in Mexico, estimated capital investment doubled between 1971 and 1976. 3) The requirements calculated for Cerro Colorado in Panama have risen in two years from $560 to $800. 4) The budget of $240 million for Sar Chesmeh in Iran in 1971 had become $500 million by 1976.

Jan 1, 1977

By A. G. Mayton, D. H. Ambrose, C. C. Jobes, N. K. Kittusamy

In a systematic study, the National Institute for Occupational Safety and Health (NIOSH) evaluated seat designs in low- and mid-seam shuttle cars during production operations at two underground coal mines in southern West Virginia. The purpose was to support, with additional data, earlier findings that NIOSH ergonomic seat designs (featuring viscoelastic foam padding and lower-back support) may help reduce health risks to operators of coal mine shuttle cars. Eight shuttle car operators evaluated seven seat designs (one already in use in each vehicle and five NIOSH designs) relative to perceived and measured whole-body vibration (WBV) exposure (including vehicle jarring/jolting) and discomfort. Operators’ perceptions using a visual analog scale (VAS) and questionnaire ratings were compared with International Standards Organization (ISO) 2631-1:1985 fatigue-decreased proficiency (FDP) limits and measured WBV levels on low- and mid-seam shuttle cars. Objective and subjective data results indicated that NIOSH seat designs (with added adjustability, lower-back support and improved seat padding) performed better to reduce vehicle jarring/jolting levels and that shuttle car operators favored them over existing seat designs. The NIOSH low- and mid-seam shuttle car seats showed 45 to 77 percent better performance in FDP and 9 to 60 percent better performance overall in operators’ ratings. Considering the VAS results for low- and mid-seam shuttle cars under no-load conditions, operators rated the level of jarring/jolting 18 to 89 percent lower with the NIOSH seats. Reductions in measured vehicle jarring/jolting were 19 to 46 percent for the three-directional vector sum accelerations relative to the existing seats on the low- and mid-seam shuttle cars. Questionnaire responses indicated that operators for both shuttle car models rated NIOSH seat designs as more comfortable overall. Vehicle operators most frequently suggested adding armrests to improve the seats on the mid-seam shuttle car. A suggested improvement for the low-seam shuttle car was to make the seat a better fit for the operator compartment, which would enhance clearance between the operator and vehicle controls and allow for better seat adjustment and operator visibility.

Jan 1, 2009

By Paul R. Smith

The theoretical requirements for the flotation d large particles are discussed. A flotation machine is described which has components which meet many of the theoretical requirements for the flotation of large particles. The machine's salient features include multiple fine-bubble attachment, froth level feeding, quiescence, shallow depth, and short flotation time. Test conditions and results are presented for the laboratory flotation of 10 mesh phosphate, 4 mesh potash, and 1/2 inch coal. In addition, test conditions and results of pilot plant flotation of minus 14 plus 35 mesh phosphate and minus 14 plus 150 mesh phosphate are also presented.

Jan 1, 1969

By Abdallah Khair, Nathalie Risso, Arie Herrera, Victor Tenorio

This study introduces a machine learning strategy to optimize icy regolith extraction from the Shackleton-de Gerlache Ridge using autonomous mining equipment. The model incorporates key parameters—distance, road gradient, vehicle load, speed, recharge logistics, and regolith water content—into a cost framework for excavation, hauling, and dumping. Regression models estimate energy and time requirements; classification predicts terrain navigability; clustering groups craters for efficiency; and K-Nearest Neighbors (KNN) determines optimal routing and scheduling. The system adapts to a six-month daylight cycle to maximize productivity and minimize costs, enabling intelligent planning for sustained lunar resource extraction under extreme environmental and logistical constraints.

Feb 22, 2026

By Paul R. Wieber

This paper describes the U. S. Energy Research and Development Administration's (ERDA) program to develop in situ coal conversion processes, especially gasification, he potential of this technology, the technical directions being explored, and the program strategy to carry the process concepts toward commercialization are emphasized. The geographic location of the U. S. coal resources and a market analysis are described. Commercially successful in situ coal processes could add over a trillion tons of coal to the U. S. coal reserves. The economics of these processes is compared with surface gasification independent studies show this process to be 25Z cheaper than surface gasification for Western coals. The major projects are briefly described. The Linked Vertical Well process is in the lost advanced stage and shows great promise. The last test produced a low-Btu gas averaging 171 Btu per standard cubic foot for average pro¬duction rates of 5.5 million standard cubic feet per day. The other projects are Packed Bed, Longwall Generator, and Steeply Dipping Beds.

Jan 1, 1977

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters while implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of the karst voids which are frequent phenomena in a carbonate rock formation. The karst system is a network of cavities that along with an omnipresent fracture network may lead to ground control issues in a limestone mine. The objective of this study is to provide a safe and reliable alternative design for a pillar in a case study mine for safe and efficient ore recovery. This research is a continuation of a previous study aimed at studying the effect of karst void on the strength of the same limestone pillar. It was assessed from the calculated pillar strength and the estimated redistributed stresses that the pillar is capable of countering more stress than is currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using Distinct-Element Modeling (DEM) to determine a better design. Discrete fracture networks (DFNs) were included to imitate the effect of the presence of discontinuities. An effort is also made to understand the variation of pillar strength with height for karst-affected pillars using two different constitutive models. This study serves as a preliminary investigation in terms of improving the future design of pillars and also while recovering old pillars prone to karst formation.

Jan 30, 2023

By Garry M. Hughes

Lynn lake, Manitoha, where Sherritt has operated a copper-nickel mine since 1954, is located north of the 56th parallel approximately SOO miles north of Winnipeg. Sherritt's new, 3,000 tpd, copper-zinc Fox Mine is situated 30 miles southwest of Lynn lake. This paper focuses on the Fox Mine concentrator, hut first some background information. Sherritt Gordon Mines Limited started mining operations as a copper-zinc producer in 1931 at Sherridon, Manitoba, 150 miles south of Lynn Lake. As Sherridon fizzled out development of a series of nickel-copper orebodies commenced at Lynn Lake. The Forward process was developed to treat the nickel concentrate from the Lynn concentrator. Sherritt's ammonia leaching process is now history and is expected to gain more prominence as pressure is applied to the mining industry for closer environmental control. But few are aware of the fact that the present Lynn Lake crushing plant and concentrator were dismantled in the autumn of 1951 and freighted from Sherridon by tractor train during the winters of 1952 and 1953. The copper-zinc orehody at Fox Mine was discovered early in 1961 by geophysical methods which included both airborne and ground surveys. It is part of a ,large body of massive and semi-massive sulphides consisting chiefly of pyrite; with chalcopyrite, sphalerite (containing 7-9% iron) and pyrrhotite in varying proportions which occur within a series of volcanic and sedimentary rocks. The total mineralized zone is a lenticular body with a minimum average length and width of 1,350 feet and 66 feet respectively, to the explored depth of 2,000 feet. The average sulphide content is 67%. Higher zinc zones are masses of pyrite grains cemented by sphalerite with lower than average copper content. Zones higher in copper and lower in zinc are slightly more quartzose. Gold and silver are present in small amounts roughly proportional to the copper content.

Jan 1, 1971

By Donald E. Ranta

An ore zoning technique developed by Climax geologists during the past forty years has been used to contour drill-hole assay values on cross-sections for fourteen porphyry molybdenum deposits in western North America, including the Climax and Henderson orebodies. Detailed geological studies of these large, complex deposits are essential in determining ore controls, which are the factors most critical to the zoning of MoS2 assays and to conceptualizing geologic models. The technique provides a detailed representation of the size, shape, grade distribution, and geologic continuity of the individual deposits. It demands a disciplined approach and adheres to rigorous rules while maintaining flexibility for adaptation to widely varying geologic conditions. By defining the limits that guide and control manual, computer-assisted conventional, and geostatistical reserve estimates, it exerts a strong geologic influence on the estimation process. A combination of ore zoning and geostatistical analysis of molybdenum deposits produces a significantly more accurate, precise, and defendable geologic reserve estimate than other methods.

Jan 1, 1983

By Erika Moonin, Jim Nickerson, Claudio Cimiotti, Roberto Bono

"In response to the severe drought on the Colorado River basin and in order to preserve existing water capacity to the Las Vegas Valley, the Southern Nevada Water Authority contracted a new deep-water intake (Intake No. 3) located in Lake Mead. The current project (Contract No. 070F-01-C1) includes 5 km (3 miles) of tunnel with very difficult geological conditions and a 200- m (650-ft) deep shaft and marine works. This paper will present the current status of the design-build contract being constructed by Vegas Tunnel Constructors and the challenges and problems faced and the innovative solutions developed to handle the difficult conditions encountered during tunneling with up to 15 bars of pressure.ProjectbackgroundThe Las Vegas Valley receives the majority of its water from Lake Mead, which is located approximately 30 km (20 miles) east of the Las Vegas, NV metropolitan area. Due to the severe drought that has hit the southwest region of the United States, the water level in Lake Mead has receded from its high water level of 372 m (1,221 ft) above mean sea level (amsl) to a low of 330 m (1,076 ft) amsl in June 2015. Should the lake level continue to fall, at elevation 320 m (1,050 ft) amsl, the current water intakes will not be able to draw enough water to meet the needs of the local area. The risk of losing water capacity has prompted the construction of a new deeper intake. Not only is the new Intake No. 3 situated at a lower elevation in the lake at 262 m (860 ft) amsl, the new Intake No. 3 is also located to draw better quality (Fig. 1).Project challengesThe project has had several difficult challenges to overcome:• The work consisted of a 1.2 kt (1,300 st) structure constructed on a barge and lowered 100 m (330 ft) into Lake Mead anchored with 9,200 m3 (12,200 cu yd) of tremie concrete.• The drill-and-blast starter tunnel was impacted by three inflow events, resulting in a one-year project delay.• One of the main challenges was selecting the tunnel boring machine (TBM) and excavating the tunnel with expected hydraulic head pressure of as much as 17 bar (16 bar was the highest pressure recorded during the drive), crossing faulted areas, low rock cover and the risk of tunnel instability due to direct connection with the lake.• Extensive pre-excavation grouting with a constant head pressure ranging from 12 bar to 15 bar.• Structural repair of the cutterhead in difficult hydrogeological conditions [water inflow of approx. 800 m3/hr (4,000 gpm)].• Complete repair of the cascade sealing system for the main bearing and two replacements of the pinion bearings.• The TBM approach to the intake structure."

Jan 1, 2015

Automation and robotics are the keys to new intelligent autonomous mining systems which can remove operators from the hazardous and stressful mining environment and provide the tools for greater productivity. This pa-per presents the components necessary for a mining Intelligent Task Control System (ITCS) in dynamic unstructured mining environments. The proposed concept is applied to develop the ITCS for an autonomous excavator. The design and implementation of a fuzzy logic controller for an excavator that uses force/torque sensor feedback to complete excavation tasks is presented. Initial experimental results are also given.

Jan 1, 1994

By Michael F. Gleason

In 1986, Gold Fields began negotiations with a large Nevada electrical power utility to supply power for its Chimney Creek Mine In northern Nevada. After the long negotiations reached an impass over various costs associated with the power line, a decision was made by Gold Fields to generate its own power. Self-generation is not uncommon overseas, but it is rare for any but very large or very small operations in the United States. Surprisingly, under certain conditions a mine can generate its own power profitably and Gold Fields has found that the associated operating and maintenance problems are minimal. The following report details what factors went into this decision and how it works. Hopefully, it can serve as a guideline for those who may find themselves in a similar position.

Jan 1, 1990

By Jon Kellar, William Cross, Eric Swanson, John Starkovich

Zirconium tungstate (ZrW2O8) is a unique material with a negative coefficient of thermal expansion. In order to fully utilize this material as a filler, a surface treatment needs to be developed to better improve the wetting and dispersion capabilities of the filler. This paper describes an initial study to characterize the filler as well as investigate fatty acid and silane surface treatments for eventual compounding with thermosetting matrices. It was found that ZrW20, has a point-of- zero charge between pH 2.7-3.0, and that both fatty acid and organofunctional silane treatments appear to be viable surface treatments for this unique filler.

Jan 1, 2003

By R. Shields

"Hard rock mines move large volumes of material, which can cause the conveyors that are essential to this movement to suffer lots of problems, including carryback, spillage, dust and belt wander. Many of these issues are created at the transfer points where the belts are loaded.This article provides an overview of the latest transfer point systems that incorporate safety and serviceability by design as well as a report on recent projects. One project is the Conveyor B Transfer at the Coeur Rochester silver mine near Lovelock, NV. Here, performance was improved with the installation of belt support cradles, engineered chute walls with external wear liner, and a compact dust collector. A second project is the improvement of belt support idlers and skirtboard sealing in a long loading zone of a conveyor under the concentrator at an Arizona copper mine.The importance of transfer pointsConveyors are essential in mine material handling. Their performance will often make the difference in mine productivity and profitability. A key to conveyor performance is the transfer points where the conveyor belt is loaded and discharges. At these transfer points, many of the problems encountered with the conveyor system are created.The problems that arise at the transfer stations include off-center and segregated loading, mistracking, blockages and plugging. And there are a variety of problems originating with fugitive material — cargo released in the form of carryback, spillage or airborne dust — that are created or exacerbated in the transfer points. These fugitive materials turn into other conveyor-related problems, including shortened component life, unplanned outages for conveyor maintenance, unexpectedly high labor costs for maintenance and cleanup, worker health and safety problems and issues with community relations. The U.S. Mine Safety and Health Administration estimates that 85 percent of conveyor maintenance is a result of fugitive material at conveyor transfer points.Technologies to improve transfer pointsA number of techniques to improve the performance of conveyor transfer points have been developed. They include:"

Jan 11, 2017

By James M. Peay

This paper discusses the recently completed organizational development research project, which was addressed to the underground mining industry. The three specific purposes of the project were as follows: (a) to determine whether Organizational Development approaches are feasible in the mining industry, (b) to provide a demonstration that Organizational Development methods can successfully contribute to the safety of underground mines, and (c) to compare the efficacy of classical Organizational Development methods, which are highly trainer- intensive, with trainer-nonintensive management development approaches. The term "Organizational Development" (OD) is here broadly defined as a management intervention for the purpose of assisting an organization with the solution of problems, which are seen by the organization as important. More specifically, we can define OD as a planned effort to improve the effectiveness of an organization through (a) team building and problem solving, which concentrates on the issues of immediate concern to the organization, and (b) efforts to improve organizational communication at all levels of the organization.

Jan 1, 1983

By Giovanni Barla

The stress-relief method for the determination of the ground stress tensor is a common procedure in rock mechanics. In particular, the method of applying gauges to the end of a borehole is a well-established technique. Investigations, both experimental and theoretical, indicate that large discrepancies can exist in the determination of the ground stress tensor when the rock substance is not the ideal elastically isotropic material assumed for the reduction of data. The purpose of this paper is to extend the analysis of strain gauges applied to the end of a borehole to rock material more closely approximate to an orthotropic substance.

Jan 1, 1969