Search Documents

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

The generation of microscopic bubbles by cavitation may enhance particle-bubble attachment and improve flotation performance. It is shown in this paper that tiny bubbles or cavities can be generated by strong shear and turbulence in high speed liquid flows. These conditions create the necessary pressure fluctuations in the bulk water to cause the local pressure to drop below a critical value. The formation of bubbles is favored by high dissolved gas contents to promote gas diffusion into the cavities, and by the presence of surfactants to provide some mechanical strength due to the adsorbed film. Experimental results on bubble formation by cavitation and consequent flotation of fine silica (d50 = 1.6 µm) are presented.

Jan 1, 1995

By Kenneth J. Leib, Laurie Wirt, M. Alisa Mast

Chemical-constituent loads were determined for an alpine stream in southwestern Colorado that is affected by natural acid drainage from weathering of hydrothermally-altered rock and from acidic metal-rich discharge from abandoned mines. Base-flow loads were compared to storm-related loads using a tracer-dilution approach. A rainstom occurred during the tracer injection, providing the opportunity to measure metal loads before, during, and after storm runoff. Chemical-constituent loads during the storm increased by 1 to 2 orders of magnitude relative to base-flow conditions. The increase in loads was related to two distinct periods; (1) a flush of higher concentrations that occurred soon after rainfall began, and (2) the peak of storm runoff. The initial flush-having no measurable change in discharge--contained the highest loads of trace metals and dissolved iron. The chemical character of peak runoff was distinctly different, as evidenced by the highest loads of total and dissolved major elements and total iron.

Jan 1, 2000

By Verya Nasri, Kevin Akbarpour, Hiva Mahdavi

"The Sheppard East Light Rail Transit (SELRT) project comprises approximately 13 km of new light rail, which will be constructed along Sheppard Avenue East in Toronto. There is a 380 metre long section of the route that will be constructed as tunnel below Highway 404, which is owned by the Ministry of Transportation Ontario (MTO). MTO has published guidelines for tunneling under its highways. An impact analysis was undertaken to predict the surface settlement and angular distortion of Highway 404 resulting from the construction of the twin tunnels. The results were then compared to the performance criteria defined in MTO’s guidelines. As a result of this analysis, it was necessary to request an adjustment to MTO’s current performance criteria. This paper presents details and results of the impact assessment, approaches taken to satisfy the requirements defined by MTO, and provides details of the adjustment permitted by MTO. INTRODUCTION Several major rapid transit projects are planned for the Greater Toronto and Hamilton Area (GTHA) located in southern Ontario, Canada. These projects are part of The Big Move (Metrolinx 2008) initiative, a 25-year, and $50 billion plan aimed at improving regional transportation. Metrolinx, an agency of the Government of Ontario, is now working collaboratively across the region to deliver major Toronto rapid transit projects to the GTHA. One such project is the SELRT. The line will largely run along Sheppard Avenue East on the surface, except for a crossing of Highway 404 where it will be constructed using a combination of open cut and bored tunneling methods. AECOM has been retained by Metrolinx as the Technical Advisor (TA) to develop the Reference Conceptual Design (RCD) and Project Specific Output Specifications (PSOS) for the project. Also, Infrastructure Ontario (IO) is the Co-Sponsor and CH2M HILL is Metrolinx’s Owner’s Engineer (OE) & Project Management Support (PMS) for the new LRT lines. This paper presents information on the tunneling settlement analysis and further work undertaken to satisfy the MTO’s requirements."

Jan 1, 2016

By C. J. Newman

Prior to 1995, the smelting process at the Kennecott Utah Copper Corporation (KUCC) smelter consisted of Noranda reactors and Pierce-Smith converters. In the consideration of expansion opportunities, the existing process did not lend itself to a program geared towards processing the total output of KUCC mining and milling operations. During 1989 and 1990, a number of smelting options were evaluated. The final selection was the Outokumpu flash smelting process, coupled with the new Kennecott-Outokumpu flash converting technology. Facilities were designed and installed to process 1.0 million tonnes per year of copper concentrate, with the ability to expand to 1.2 million tonnes per year. Following the shutdown of the smelter facility utilizing the Noranda technology in May 1995, the flash smelting furnace commenced operation in June with the flash converting furnace startup following a few weeks later. The smelter has achieved design production targets and environmental goals. Current operating rates are at or above design rates for concentrate and matte processing. Emissions are lower than the permit levels and equate to less than 3.5 kg of S02 per tonne of copper. This paper outlines the design, construction, startup and the first two years of operation of the modernized KUCC smelter.

Jan 1, 1998

By S. Kelebek, S. O. Fekete

The flotation process developed at Falconbridge laboratories utilizes sulphur dioxide and diethylenetriamine (DETA) reagent combination in the depression of pyrrhotite to allow its separation from pentlandite and chalcopyrite. DETA by itself has failed to produce flotation selectivity with samples from plant and pilot plant streams which showed relatively high redox potentials. However, DETA was found to function effectively on laboratory-generated samples under certain conditions. The results of poor depression are in keeping with thermodynamic calculations which indicate that in the presence of sufficient xanthate and DETA, the formation of ferric dihydroxy xanthate and dixanthogen is possible under oxidizing conditions. The use of sulphur dioxide alone has also resulted in a rather poor depression of pyrrhotite. However, the combined use of these reagents has resulted in an efficient and consistent separation of pyrhotite from pentlandite and chalcopyrite. Various aspects of this selective flotation system are presented along with a discussion on possible operating mechanisms.

Jan 1, 1995

The Sandvik Group (Sandvik AB), headquartered in Sandviken, Sweden, continues to expand its worldwide operations growth. After recent acquisitions, including Tamrock, headquartered in Tampere, Finland, the company now has annual sales of more than US$5 billion (SEK 40 billion). With the acquisition of Tamrock, Sandvik has further increased its interests in the mining industry. Sandvik Rock Tools, a familiar name in the mining industry, is one of the world's leading suppliers of rock-drilling tools. And Tamrock is one of the world's leading suppliers of drilling machinery, loaders and equipment for rock-excavation operations. Sandvik believes that the two companies combined offer customers "maximum productivity through total system solutions, including machinery, service and tools." In 1997, Tamrock posted sales of US$940 million (SEK 7.5 billion). In addition to its expertise in drilling tools and equipment, Sandvik is supported by its collective resources in specialty steel and cemented carbide. These resources include extensive research and development capabilities, with annual investments in R&D now at about US$150 million. As a result of the R&D programs, internal expansion and acquisitions, the company has nearly doubled in size during the past four years. From 1994 to 1997, nearly US$1 billion was invested in internal growth and another US$825 million has gone towards acquisitions. Return on net assets is now 22% annually. In addition to Tamrock, acquisitions of interest to the mining community include Drillmaster Inc., Houston, TX. The acquisition of Drillmaster (by Sandvik Rock Tools) has further strengthened Sandvik's position in down-the-hole drilling tools. Other major recent acquisitions by Sandvik include Kanthal, a Swedish manu¬facturer of metal and ceramic-resistant materials for electric heating furnaces, household appliances and elec¬tronics, and Precision Twist Drill, Crystal Lake, IL, one of the leading producers of high-speed cutting tools. With more than 38,000 employees worldwide, the Sandvik Group is divided into six separate business areas. Each area is responsible for its own R&D, production and sales: ? Sandvik Mining and Construction. Including Tamrock and Sandvik Rock Tools, this business area boasts of offering the most comprehensive range of "rock-working" products. These include drilling rigs, loaders, rock-excavation equipment and rock drilling tools. ? Sandvik Specialty Steel. This area includes Sandvik Steel and Kanthal, manufacturers of stainless steel tube, strip wire and bar, as well as high-alloy steel and specialty metals. ? Sandvik Tooling. This business area consists of tools and tooling for metalworking applications. Sandvik Coromant is a market leader in the development, manufacture and marketing of tools using cemented carbide, ceramics and extremely hard materials, such as diamond and cubic nitrite. CTT Tools is the world's largest manufacturer of high-speed steel tools and is now expanding operations into solid cemented-carbide tools. ? Sandvik Hard Materials. This segment produces a full range of "hard materials," ranging from cemented carbide to diamond. This area manufactures and markets a full range of cemented carbide blanks for tool manufacturers, as well as components and rolls. ? Sandvik Saws and Tools. This business area manufactures high-quality handsaws and metal saw blades, as well as hand tools ranging from wrenches to chains for logging machines. ? Sandvik Process Systems. This segment manufactures steel belts, process systems and automatic sorting systems for the chemical

Jan 1, 1998

When solid pillar is not left to separate different mining levels in underground mine with high dip angle deposit, waste rock in the backfilled stope could be a safety hazard to future mining activities on levels above or below the backfill. Different backfill methods can be used to eliminate this hazard according to the deposit shape and mining method. Building concrete pillar in ore drift of each mining level is one of them. Concrete pillar had been constructed in underground mines based on operational experience. Little design literature and pillar performance data can be found. At Great Basin Gold Hollister Mine, over two thousand feet of concrete pillar had been constructed. The project started with engineering design which combined civil engineering concrete design and the specialties of underground construction. Time Domain Reflectometry technique was installed to monitor the pillar movement and concrete cylinder samples were collected and tested for quality control. Engineering design, underground construction, quality control and concrete pillar monitoring, as well as precious concrete mixing data from years of experience are fully covered in this paper to give a general frame of concrete pillar method.

Jan 1, 2010

By Rolf Christiansson, Daniel Johansson, Urban Åkeson, Henrik Ittner, Mats Olsson

"This paper presents two recent studies on the extent of blast damage after excavation in crystalline rock. The Swedish Transport Administration and the Swedish Nuclear Fuel and Waste Management Company (SKB) are both under regulations to limit excavation damage during construction of tunnels. SKB is also required to limit the Excavation Damage Zone (EDZ), as this could be a potential flow path for radionuclides in the planned repository for spent nuclear fuel. Presented in this paper are investigations of blast damage from three tunnel sites, a road tunnel, an experimental tunnel in Äspö Hard Rock Laboratory and an underground subway depot. As expected the fractures resulting from the bottom charge are both longer and more frequent then those mapped in the column charge. The results show that the requirement to limit blast damage according to Swedish regulations was fulfilled for the column charge at the three studied sites.1 INTRODUCTION The Swedish Transport Administration (TRV) and The Swedish Nuclear Fuel and Waste Management Company (SKB) have both recently completed studies related the extent of blast damage from modern explosives after excavation. SKB studies focused on blast damage from pumpable emulsion explosives for underground construction (Ittner and Bouvin 2015) and hydraulic connectivity in the EDZ (Ericsson et al. 2015). TRV had a broader focus with different types of explosives including blasting for both road cuts and tunnelling with pumpable emulsion explosives. Investigations by means of geophysics were also conducted (Olsson et al. 2015). High demands on perimeter control and excavation damage is usually required for underground constructions with a long operation time, such as public tunnels for transport or underground repositories for nuclear waste. This paper presents the findings of recent Swedish studies and aims to discuss the topic in a broader context."

Jan 1, 2016

More than 5,300 mining professionals from around the world attended the SME Annual Meeting and Exhibit, March 1-3 in Denver, CO. Seventy three technical sessions highlighted innovative technologies and applications for the development of mineral resources. And the exhibit featured 421 companies worldwide and 632 exhibit booths. The 1999 SME Annual Meeting had 10% international attendance Professionals from outside the United States were guests at the first SME International Reception. Other meeting highlights included the Keynote Session. This pivotal session examined the international experience of North American-based companies. Speakers presented their perspectives on international explorations and operations. Keynote speakers included Robert Buchan, Chairman an( Chief Executive Officer, Kinross Gold; Dave Baker, Director Global Mining Project Management, Caterpillar; and Leendert Krol, Vice President International Operations Newmont Gold. Ihor Kunasz, 1998 SME President, made the introductory remarks.

Jan 1, 1999

By Douglas Owen

Two case studies describe the introduction of technology new to an organisation. The lessons learnt from these Case studies contribute to Our general understanding of the management of technological change.

Jan 1, 1989

By Ross W. Smith, D. L. Taylor, K. A. Altman

Traditional sensitivity analysis of metallurgical data has the potential to overestimate the value of mining projects. Such analyses provide no information about the probability of the results. Simulations that rely on the input of statistical information provide more realistic predictions of the value of future projects and offer additional information regarding the probability of the outcome.

Jan 1, 2003

By C. Caceres

Fibre reinforced shotcrete in combination with other types of support systems is becoming the leading support method for underground excavations, especially those present in low quality rock masses. Sudden or rapid ground support failure can expose workers to safety hazards, damage to equipment and others resulting in production interruptions that will impact the cost of operation. Knowing the peak and post-peak strength characteristics of the support system over time are of major importance. Round Determinate Panel Testing of fiber reinforce shotcrete is the primary test used by the mining industry to determine strength characteristics; however, the tests are costly and significant manpower is required in a mine environment to build, store, handle and test the panels. For these reasons numerical modeling can result in an effective method to produce realistic results. This paper examines the strength characteristics Round Determinate Panel tests and its ultimate application in underground excavations, using Itasca?s three dimensional particle flow code (PFC3D).

Jan 1, 2010

By Muammer Kaya, Derya Oz

The main objective of this study was to remove printing ink from waste newspaper and improve the de-inked paper brightness as close as the unprinted paper by bleaching agents. This paper summarizes results of laboratory investigation into the de-inkability of newsprint printed with offset printing. Different chemicals and process parameters were varied to assess the effect on the brightness and cleanliness. The operations involved in de-inking process are briefly described and some of the problems being encountered are discussed.

Jan 1, 1995

By B. D. Nichols, W. S. Gregory

SOLA-DM is a three-dimensional finite-difference computer code designed to model the dynamics of an incompressible fluid and the transport of discrete particulate material around obstacles impervious to flow. The numerical methods used in this code are described. SOLA-DM was used to predict the particle flux sampled by the 10-mm Dorr-Oliver Cyclone and MINIRAM dust monitors. Various geometric and dynamic variations of monitor and airflow combinations were tested. The code predictions are shown in computer-generated graphic plots.

Jan 1, 1987

By T. J. Dudek

To be competitive in automotive applications, polymer composites must be processable by high production rate processes like injection molding (IM), reaction injection molding (RIM), structural rim (SRIM) and compression molding. With current fiber reinforced composite materials, performance properties are sometimes compromised to make them compatible with these processes. This is done by decreasing the amount and length of the reinforcing fiber and the viscosity and molecular weight of the polymer matrix. Sheet molding composite (SMC) and thermoplastic polymer blends are examples of polymer composites which are cost effective in many applications and meet the high speed processing requirements for automotive parts.

Jan 1, 1993

By Colin M. Kelly

The Loveridge Mine, located near Fairmont, West Virginia, has been mining coal from the Pittsburgh Seam since 1958. As the mine develops its reserves it finds itself with increasingly distant hauls from the operating faces to the preparation plant. Initially, the mine was designed with track haulage. The coal was hauled to an underground rotary dump which fed a slope belt, to the preparation plant. As the haulage distances increased, production delays due to the track system's limitations became severe. To resolve this situation, a complete review of the haulage system was undertaken. Simulations of the present system along with future scenarios were conducted to help management effectively plan the haulage requirements of the mine for the remainder of its life.

Jan 1, 1986

By G. Pierson

Explanations for commodity price levels (or movements) commonly focus on the fundamentals of supply and demand, otherwise they are simply assigned to speculative activity. Comparisons of metal-price histories to monetary and other economic data support the argument that the supply of and demand for money are no less important in the determination of price than are the supply and demand of the commodity itself. That these relationships should exist is evident in the price identity and they are consistent with monetary theory. The patterns developed have limited usefulness as predictors, but their recognition is essential for the construction of price scenarios for planning purposes.

Jan 1, 1997

By R. Addison, P. V. Avotins, D. W. Kestner, M. F. Dibble, L. A. Haas, M. D. Flavel, D. Halbe, D. J. Barratt, G. V. Jergenaen

Mineral processing in 1980 can be described by several key words, familiar to the industry throughout the past decade: complex, low grade, environmental, energy, high tonnage, and economics. Flowsheets have become more complex in order to treat lower-grade, finer-grained, more complex ores and still meet environmental and economic constraints. Operators and researchers have had to cope with these problems, which have resulted in marked trends in mineral processing. The use of advanced instrumentation in process monitoring, control, and modeling has been increasing to deal with fluctuating ore grades, higher plant capacities, rapidly rising operating costs, and process complexities. The industry has been presented with new generations of equipment that reportedly do the job more efficiently and at a reduced cost. The need to meet stricter air and water environmental standards has resulted in a concerted effort by the mineral industries to obtain an appropriate balance between the needs of mining and mineral processing and the requirements for proper environmental, safety, and health protection. Energy and economic considerations have led to increased equipment size, particularly in grinding, flotation, and conveying. Throughout all phases of mineral processing there has been an effort to reduce energy consumption. One avenue followed by researchers and operators was the testing and use of chemicals to reduce energy requirements.

Jan 5, 1981

By G. H. Jardine

Mine planning and production scheduling in surface mines are basically iterative processes which are ideally suited to the use of computer-based techniques. Both processes are truly three-dimensional and lend themselves to the application of 3-D interactive graphics. Until recently, this has applied the need for the costly, dedicated graphics screens and mid range minicomputers. However, ongoing advances in processor chip design led to the emergence of inexpensive and powerful 5 to 10 Mips desktop work- stations. These workstations have the processing power to support rapid, high resolution, 3-dimensional graphics. By combining these workstations with powerful 3-D CAD software and, with a suite of comprehensive mine planning and scheduling applications, Mincom has developed a most cost effective solution to modern mine planning challenges.

Jan 1, 1989

By J. Ragot, D. Maquin, N. Heraud

Acquisition of coherent and representative data about the state of processes remains a major problem of process control. This paper proposes an approach that ensures coherence in measurements on an operational industrial process. The basic technique employed relies on balance equilibration of resource mass flow. An interesting particularity of the set up is the ease with which it can be adapted to check productivity or detect sensor failures. In the case of sensor failure, it suffices to examine the evaluations before and after balance equilibration. The algorithm was tested by means of computer simulation using data from an industrial metallurgical flowsheet.

Jan 1, 1992