Search Documents

By Michael Swisdak, John Tatom

In a quantitative risk assessment (QRA), the ability to accurately model real-world situations is obviously critical. In the end, the model must be able to represent the effects produced by the detonation of the donor and the consequences on the target. The science that goes into such a model must be carefully thought-out and based on as much data as possible.

Jan 1, 2007

By James W. Reil, Douglas A. Anderson

Common wisdom has it that a blast which breaks rock efficiently should-generate less ground vibration. In practice, however, this idea has not been-rigorously tested. In a previous paper presented at an SEE meeting[1] we described a method for-controlling vibration using delays. The method is very effective in controlling-annoying low-frequency ground vibration. We noted that observed ground-vibration differs in some respects from that predicted by adding single-charge-waveforms.

Jan 1, 1988

By Roger L. Keller

This paper covers the design and test blast procedures for several drop shafts and edits leading to the completion of a recent Rochester Pure Waters Expansion Project . Due to the projects "in-town" presence, and its close proximity to many sensitive vibration sites, very stringent ground vibration limitations and guidelines for blasting were places on each site.

Jan 1, 1991

By Robert L. Brooks

Blasting liability problems are frequently compounded by a company's inability to effectively communicate with concerned property owners and the lack of adequate complaint documentation. Often, by the time the insurance carrier becomes involved in a blasting claim, the situation has deteriorated to the point that a solution agreeable to both parties is virtually impossible to reach. The insurance carrier, wishing to minimize their lose potential may decide to pay on a somewhat questionable blasting claim rather than be drawn into lengthy civil proceedings that would ultimately end up in front of a jury with little chance for a successful outcome.

Jan 1, 1992

By Kazuyoshi Kawami, Fumihiko Sumiya, Kunihisa Katsuyama, Yuji Ogata, Koichi Kurokawa, Yuji Wada

When explosives are detonated in the borehole where there is an air gap between the explosive charge and the borehole of inner wall, the shock cave in an air gap travelling ahead of the detonation front sill be generated. This shock wave is called the precursor air shock wave (PAS). The explosive is precompressed by the PAS, and as a result of that the detonation failure occur on occasion. This phenomenon is well known as channel effect.

Jan 1, 1994

By William Yutmeyer, Meredith Hardwick

Since 1996 there have been at least two teams formed within the U.S. Government to develop a consistent set of risk-based standards to be used to govern safety. The first of these was the Risk and Lethality Commonality Team which developed risk criteria associated with protecting personnel during launches at the national test ranges. The second team titled the Risk-Based Explosives Safety Criteria Team (RBESCT) is the subject of this paper.

Jan 1, 2007

By Glenn Ludwig, Stephen H. Chung

Fragmentation has a direct impact on mine costs and productivity. Computer programs have been developed to calculate fragmentation using data on the properties of the explosive, the characteristics of the rock, the rock mass and the blast pattern. While computer models can yield good data, conclusions must be verified. Fragmentation assessment, muckpile surveys or high speed film analysis of rock mass movement are some of the techniques that have been used to confirm blast results. Digitizing photos of the muckpile is now the most common method to assess fragmentation. But it has some drawbacks. Although automatic electronic imaging equipment speeds up the process, the results depend on the photographs. Shadows will distort results. High resolution, black-and-white prints are essential.

Jan 1, 1992

By Pierre Mousset-Jones, Jaak Daemen, Songlin Zhang, Jon Hurley

Most western United States open pit gold mine ore bodies are disseminated deposits. The mineralization is so irregular that it is difficult to visually identify the ore/waste boundary. Blast hole samples are used to interpolate digging polygons based on the pre-blast position of the bench. Dilution caused by blasting is of major concern at these mines, since blast movement can mix and dilute the ore and move it beyond flagged digging polygons established on the blasted rock according to their pre-blast location. Typically, mines try to reach a compromise between blast fragmentation and movement.

Jan 1, 1994

By James Stuart

Explosive components are common in electric power distribution systems. Basically, we use explosives either to open or to close a circuit very quickly, in order to avoid electrical catastrophe. We use explosives in these important applications, because explosive materials are compact, inexpensive, long-lived, powerful, and can be triggered instantly. A lead-alloy fuse will melt when excessive electric current passes through it. A small fuse of this type melts quickly. However, a lead-alloy fuse for high current levels must be larger, and takes longer to melt. Thus, at high current levels, a lead-alloy fuse offers inadequate protection, because electrical catastrophe might happen, before the fuse melts. We need faster-acting, explosive components.

Jan 1, 2009

By David A. Paul

Over the past several years a great deal of information on blasting vibrations and their effects on structures has been generated. Much of this knowledge has been gained through the use of ground vibration measuring equipment. While this type of information is valuable and gives us great insight into damage that can be incurred by structures from this source, very little, if any, information of this quality is available for the vast majority of cases in which an engineer is called upon to investigate alleged damage from ground vibrations. For the investigative engineer, then, the problem becomes one of accumulating whatever data is available and drawing a conclusion as to whether or not the subject structure was in fact damaged by the blasting vibrations. Such an analysis certainly requires a working knowledge of the literature on the subject and as much experience as he can bring to bear. Even thus armed, however, the data is often ambiguous, confusing, and/or contradictory. A practical approach is presented herein to aid the engineering investigator in arriving at the best possible conclusion available with the information at hand.

Jan 1, 1983

By D. Johansson, C. San Miguel, U. Stenman, N. Petropoulos

Blasting is a commonly utilized method in civil engineering projects and mining operations. Ammonium nitrate-based (AN-based) explosives are the most efficient explosives today in terms of handling and performance. However, a side effect is the production of gases. The reduction of these gases plays an important role in the safety and environmental aspects in the working place. Therefore, optimizing the recipes of explosives is vital for minimizing the environmental impact and increasing performance. The aim of the project is to provide results and recommendations on the use of emulsion commercial explosives to support the Swedish mining industry and tunnel-contractors as well as the explosives manufactures. The approach was to test various recipes of civil emulsion explosives to investigate the generation of toxic fumes (CO, CO2, NO, NO2 and NOx) during their detonation. To further increase the knowledge of the influence of different additives, ammonium nitrate prills were added in various percentages. The experimental configuration consisted of magnetite mortar cylindrical specimens with a 50 mm borehole at their center, filled with emulsion explosive. Several tests with different emulsion compositions regarding ammonium nitrate additives (10%, 20%, 25%, 30% and 35%) were carried out in a blasting chamber. The measurement equipment was composed of a flue gas analyzer. The instrument was meticulously cleaned after every test, as well as before and during the tests due to condensation (high humidity and dust) at the inlet of the instrument. The emulsion was manually sensitized with microballons and pumped into the cylinders to ensure lack of bubbles, which could introduce inhomogeneities. The acquired gas concentration data was complemented with temperature, humidity, and VoD measurements. The results showed a linear increase of nitrogen gases as the percentage of ammonium nitrate prills increased. On the other hand, carbon gases had a relatively low coefficient of determination. The VoD data showed a behavior that can be described with a simple quadratic equation.

Jan 1, 2024

By S D. Cummings

"CRACKS CONCERN CORPORATION" Was the headline on the front page of the Terre Haute Tribune Star, March 1994. Having spent several years following up on blast-induced damage allegations made this article especially interesting. Knowing that there were no operating mines within 30 miles of this newly built, yet to be occupied building, also made the reading more enjoyable. The article went on to read, "Vigo County school officials have asked architects to find out whether some cracks in walls at the new school are due to NORMAL settling or if they indicate serious structural problems." It is obvious that if there were a mine within "Feeling" distance, blasting and the operator would have immediately become suspect as at least one of the potential causes. More alarming is that the investigation may have stopped there.

Jan 1, 1995

By Michael S. Wieland

Underground coal-mine explosives (permissibles) can be substantially degraded by the underground stress waves from the explosion of neighboring borehole charges. This cross-borehole interaction generally yields the worst receptor (impacted) charge performance when the borehole separations are too close. For explosives which recover, the receptor degradation is worst when the delay until firing is small. Except for a poor quality muck pile or unreacted cartridge fragments, degraded charge malfunctions of this type are difficult to detect in coal-mine delay blasting. A simulator which reproduces the underground wave/receptor charge interaction and special underwater donor/receptor tests were utilized to study this transient desensitization problem. Test results revealed reductions in receptor energy output, delayed transitions into detonation, inferior reaction rates, or sympathetic reaction responses from the impaction. Tests on detonators showed reduced tip-strength, abnormal functioning times, or sympathetic firing as a result of transient impaction. The cross-borehole desensitization and sympathetic reaction response problems warrant concern because they are logical mechanisms for raising the risk of hazardous mining conditions, including blown-out shots, flyrock, charge deflagration, and methane/coal dust ignitions.

Jan 1, 1987

By Paul Worsey, Matthew K. Coy

New blasting mat designs are currently tested in the field on actual blasting jobs and only undergo qualitative rather than quantitative assessment. The majority of matted blasting occurs in trenching in which the blast designs and field conditions vary considerably. In order to assess a new blasting mat material and design, a new standard test was devised.

Jan 1, 2015

By W. Fourney

In the late 70’s and early 80’s in conjunction with other oil and gas well stimulation studies, personnel from the Dynamic Effects Lab performed model testing to demonstrate the effectiveness of utilizing an open section of borehole just before a plug. We called the process stem induced fracturing. The open section beneath the stem was used to increase the pressure magnitude and spread out the duration of the pressure pulse. This technique was later utilized to by Frank Chiapetta (1) in the fracture and fragmentation of rock in quarry blasting situations. He called his technique air deck blasting. In fact, Frank found that the Russians had previously discovered the same technique. There is currently interest in utilizing air deck blasting with an open section of hole beneath the explosive at the bottom of the bore hole to better remove the toe in a fragmentation shot. This paper reviews the development of stem induced fracturing and then describes a series of model tests conducted to measure borehole pressure at points along a borehole when an explosive charge is detonated at the midpoint of the borehole. Tests were conducted in both stiff boreholes (aluminum) and less rigid boreholes (PMMA-Plexiglas). Pressure time profiles were measured at the charge site, midway between the charge and the bottom of the hole, at the stemming at the top of the borehole, and at the bottom of the borehole. Crack initiation sites and crack propagation were also determined in the PMMA models. Some high speed pictures were taken of the event in the PMMA.

Jan 1, 2006

By Ann Barron, Paul Downing

Those employed in the explosives industry must have a keen familiarity of the explosives products they handle, the safety pro c e d u res they must follow, and the increasing number of laws and regulations governing blasting operations in order to perform their duties satisfactorily. For this reason, companies must make certain that their employees have the necessary knowledge and full understanding of their blasting and non-blasting responsibilities. Consequently, training is one of the most important elements in any company’s safety program.

Jan 1, 2004

By D T. Froedge

The state of Kentucky is making some changes in it's blasting program namely instituting a training program for blasters and instituting a new classification of blaster titled "Class A Kentucky Blaster". These changes will take place within the next year and are felt to be of great interest and benefit to those in the blasting industry.

Jan 1, 1978

By John W. Brown

During the summer of 1994 the mining industry experienced numerous accidents involving blasting related incidents. The Tri-State Chapter of Explosives Engineers planned a meeting to discuss three of these accidents.

Jan 1, 1995

By Frank Hirthammer

"Nowadays, security in the lifecycle of explosives is more important than ever. Terror attacks all over theworld pushed the EU to decree a Commission Directive for the identification and traceability of explosives that set a series of requirements for involved manufacturers, distributors and end-users. The challenge was to find and implement a track and trace system for all concerned European companies byApril 5, 2015. Since then, countries worldwide have followed this example and implemented similarregulations."

Jan 1, 2017

By Paulo Cesar Pavan

T&T or Traceability, is a concept of generating, storing and on demand providing information about all traceable items in the supply chain

Jan 1, 2019