Search Documents

By Faisal Shalzad, Adnan Anwar Malik, Tadashi Maejima, Jiro Kuwano

Single helix screw piles carry most of the structural load through end-bearing if the helix is embedded in the dense bearing layer. The tip condition of the central shaft of the screw pile can be closed, closed with cutting blades, opened with flat cut, and opened with wedge shape cut and its selection is based on the insitu ground conditions. These different end conditions of the central shaft disturb the ground differently, leading to the change in bearing capacity. In this study, an attempt is made to investigate the effect of open and close-end screw piles on installation effort (installation load and torque) and bearing performance in the dense bearing layer. The model steel screw pile with a pile shaft diameter of 21.7 mm and helix diameter of 43 mm is used in this study. Test results show that the open-end screw pile required less installation effort than the close-end pile that penetrated the bearing layer by 1Dhwith an unplugged condition. Further, the open-end screw pile shows a higher bearing response than the close-end screw pile if it enters the bearing layer with an unplugged condition.

Oct 1, 2022

By Peter Middendorp, David J. Tara, Gerald E. Verbeek, Jan Fischer

"For pile driving simulation the model used must be accurate for the entire process, i.e. from the start of pile driving until the pile has reached its target depth. Of the various model components (hammer, pile and soil), the soil is the most difficult to characterize accurately. This is well known, but the aspect that is not as well understood (and therefore commonly misapplied) is the fact that the soil properties and thus the soil parameters do not remain constant during the pile driving process. Furthermore, this phenomenon of soil fatigue, mainly for skin friction, as a continual change of soil resistance during pile installation, is not implemented into all commonly applied pile driving simulation software and could therefore not be taken into consideration. In this paper the effect of soil fatigue will be described by numerous research results, showing that this effect will occur regardless. Different methods to consider the change of soil resistance during pile installation will be presented, some applying soil fatigue while others merely reduce soil resistances. Using currently available wave equation software that can take soil fatigue into consideration, the importance of doing so will be shown on the basis of the back calculation of a monopile installed offshore in Germany.THEORY BEHIND SOIL FATIGUESkin friction and toe resistanceTo simulate pile installation as accurately as possible, detailed geotechnical knowledge about the mechanical behavior of the soil surrounding the pile is necessary during each step of the installation process. Therefore, to ensure ""geo-mechanical correctness"" of a pile driving simulation, the shaft friction and the toe resistance have to be recalculated at each penetration level. For the skin friction parameters this is especially important since they change significantly during pile installation because of soil fatigue. Depending on the pile and soil type, the toe resistance can experience changes as well due to soil fatigue during to pile driving. However, in this paper the toe resistance values were kept constant over the entire penetration depth.In general, the unit skin friction can be derived from measured values (CPT, qs) or calculated as a function of the horizontal effective stresses dh acting perpendicular to the pile wall of a vertically driven pile. The horizontal stresses can then be converted into the unit skin friction qs using the Mohr-Coulomb failure criterion:"

Jan 1, 2017

By A. Rod Kern, Michael A. McNicholas, Yaser Taheri

Deep foundations were required for construction of an 18,000 ft2 (1,672 m2) 4-story office building and an adjacent 23,750 ft2 (2,206 m2) 5-story parking garage in Queens, New York due to an existing uncontrolled fill layer ranging from 15-20 ft (4.6 - 6.1 m) in thickness beneath the building footprint. The geotechnical engineers for the project initially selected auger cast-in-place (ACIP) piles over driven piles to limit the impact of noise and vibrations on the surrounding neighborhood. Ultimately, drilled displacement piles (DDP) were installed since this method offered a more economical solution that would generate the required pile capacity with shorter drill depths and would also mitigate spoils volume. During installation of test piles by the geotechnical contractor retained for the foundation work, multiple unanticipated soil conditions were encountered that would adversely affect the constructability of the piles. The existing fill contained significantly more natural and manmade obstructions than expected and the underlying glacial soil became too dense to penetrate at shallower depths than anticipated. This paper discusses how these issues were overcome through pre-drilling and the use of detailed instrumented test pile data coupled with in-house engineering capability to proactively re-evaluate minimum pile lengths at any given location and keep the project on track. INTRODUCTION Geotechnical work in the New York City market presents soil conditions that can be highly variable and challenging due to the presence of uncontrolled urban fill placed over the native soils. Construction in this area can therefore pose many unforeseen challenges, even with detailed geotechnical analysis being performed at project sites. A case in point is a construction site in Queens, New York. The proposed site development consisted of construction of a 4-story office building with a footprint of 18,000 ft2 (1672 m2) and a stand-alone 5-level parking garage with a footprint of 23,750 ft2 (2206 m2), together with associated new pavements and utilities. The site is bordered by a mix of commercial buildings and residential properties on all sides. Depth of the uncontrolled nature of the fill extended up to 20 ft (6.1 m) below street grade. Given the significant cost associated with removal and replacement, deep foundations were recommended to bypass the unsuitable soils and support the structures at depth where good bearing material existed.

Jan 1, 2019

By Seyyed Mehdi Radeghi Mehrjou

It is important to study structures and their retrofitting techniques in order to avoid earthquake-induced seismic damage within countries that are prone to earthquakes. Todays, micro piles are employed as useful structural components for seismic behavior improvement. The present study analyzes inclined micro piles subjected to seismic loading by using the three-dimensional finite difference method (FDM). FDM assumes an idealized three-dimensional soil-micro pile model to perform logical behavior evaluation in the event of an earthquake. Linear and elastic micro piles and elastoplastic soil were employed in this study. The Mohr-Coulomb criterion was employed in the failure control of the micro piles. The micro piles were subjected to the 1978 Tubas earthquake records. The numerical results were compared to experimental data. The comparison revealed good agreement between the numerical results and experimental data. The inclined micro piles were found to sufficiently enhance soil strength under seismic loading, inducing smaller displacements than vertical micro piles. Furthermore, the soil and inclined micro piles showed salient interaction.

Sep 1, 2022

By Athena C. Denivo, Pablo V. Lopez, Sissy Nikolaou, Alfred H. Brand, Ahmad Rahimian, Rudivien G. Josef

"The United States Tennis Association (USTA) Billie Jean King National Tennis Center (BJKNTC) site is located in the northeastern portion of the Flushing Meadows Corona Park area of Queens, N.Y. The site occupies some of the most difficult subsurface conditions for construction in the New York City (NYC) metropolitan area, with unique challenges from geotechnical, seismic and foundation design perspectives.At the USTA site, Paleozoic crystalline bedrock is found at a depth of roughly 300 to 400 ft (90 to 120 m) below grade. The geologic history of the site is complicated, starting from the early Pleistocene, when the ancient Hudson River temporarily changed course, flowing across Queens enroute to the Atlantic. It eventually carved a deep valley through the Cretaceous soils, in some places all the way down to bedrock. A series of glaciers advanced and retreated across the region during the Pleistocene times, filling the deep valley with layers of assorted glacial soils. At its southern edge, the last major glacier to flow across the region built up a ridge at the southern tip of Flushing Meadows known as the Harbor Hill terminal moraine. This ridge blocked the valley forming a dam, so as ice started melting away the valley filled up with a lake fed by glacial meltwater. Layers of clean outwash sand and varved silt and clay filled the glacial lake. The ice did not retreat in a steady manner, instead periodically readvancing over the previously deposited soil in the lake, then retreating far enough to let the lake drain temporarily into Long Island Sound, before readvancing again.As a result of this repeated sequence of retreat, advance, retreat, etc., there are places where a “crust” of desiccated soil formed when the lake drained, and areas with interlayers of outwash sand where ice readvanced into the lake. When the ice melted north of Long Island Sound, the glacial lake filling Flushing Meadows drained forming Flushing Creek. During the Holocene (roughly the last 11,000 years), as ice melted further away and sea-level rose, low lying areas filled with river sands and marine clays, along with coastal marsh deposits. Table 1 lists the soil design properties on site and Figure 1 exhibits the geologic section across the site."

Jan 1, 2015

By John P. Turner, Mark Jen, Bobby Daita

"The Port Authority of New York and New Jersey is replacing the existing Goethals Bridge built in 1928 which is deemed to be functionally obsolete. The replacement bridge will consist of a dual cable-stayed Main Bridge crossing the Arthur Kill with elevated approach spans connecting Elizabeth, New Jersey and Staten Island, New York. The main bridge towers are supported on a group of six nine-foot diameter drilled shafts that transition into a pier cap. The anchor and approach piers are supported on two column bents with each column supported on a single drilled shaft. The 4.5 to 10 feet diameter drilled shaft foundations have permanent steel casing to rock and socketed into bedrock. Subsurface conditions consist of Passaic Formation bedrock overlain by varying thicknesses of overburden soils. The foundation design assumes permanent casing extending a minimum 2 feet into the weathered bedrock. Rock socket lengths below the permanent casing vary between one to two shaft diameters based on the quality of the bedrock. The reinforcing design was based on AASHTO LRFD minimum requirements, force demands, seismic detailing requirements and also considering the continuity between the shaft and socket.The bridge is currently under construction with approximately 70 percent of the foundations installed. Several field conditions encountered at various stages of shaft construction between casing advancement and concreting required design and construction modifications. Based on the driving method and the quality of the bedrock, the tip of the permanent casing hit refusal either above or below the design elevation, requiring modifications to the drilled shaft design and its reinforcement. This paper provides an overview of the general subsurface conditions at the site and its impact on foundation design and discusses the detailing worked into the design to accommodate tip elevation variations, as well as various foundation design modifications in response to actual conditions encountered during construction."

Jan 1, 2016

By Kenneth Gavin, Weichao Li, Paul Doherty

"The lateral load capacity is one of the most important issues to be considered in designing piles to resist berthing loads, ship impact forces and for monopiles used in the offshore wind sector. A number of semi-empirical design approaches are available to calculate the ultimate soil resistance and assumed soil reaction profile along the piles’ embedded depth. In order to investigate the response of monopiles to lateral loading, a series of field experiments were conducted on instrumented steel pipe piles. Two lateral loading tests were performed on model piles with a diameter, D, of 340 mm and embedded depth, Lem, of 2.2 m, giving a Lem/D ratio similar to those adopted in the offshore wind sector. The piles were driven into dense sand at the University College Dublin geotechnical test bed site in Ireland. 10 pairs of strain gauges were installed on each model pile along the embedded depth at 10 levels to capture the load transfer and bending moment within the piles. The deflection and rotation at the model pile head were measured by Linear Variable Differential Transformer (LVDT) and inclinometers. The tests results were used to perform a detailed evaluation of current design methods. In the final section, discussion on the determination of the ultimate lateral load capacity for monopile design was conducted. IntroductionA pile’s lateral load capacity is determined, for design purposes, by two conditions: 1) the ultimate lateral load, Fu, divided by an appropriate safety factor; and 2) the load according to the maximum lateral deflection that the support structures can sustain. In view of the first condition, design methods to calculate the ultimate load were developed for piles used in the offshore oil and gas sectors, which tend to be much more slender than monopiles used in the wind industry. The purpose of this study was to investigate whether these design methods provide reasonable estimates of ultimate capacity, for short rigid monopiles.The methods to determine the ultimate lateral load generally follow three steps: 1) determine the ultimate soil resistance, Pu, along the pile embedded depth; 2) adopt the most appropriate soil reaction profile, Pz, along the piles embedded depth when the pile subjected to the ultimate lateral load condition (four of the most popular ones are depicted in Figure. 1); and 3) ensure equilibrium of lateral forces (see Equation 1, symbols are listed at the end of the paper) acting on the pile and bending moments (see Equation 2) about a point in pile is employed to determine the ultimate lateral load."

Jan 1, 2015

By Dan A. Brown

The foundations at the Huey P. Long Bridge in New Orleans presented special challenges for construction due to the requirements for very deep drilled shafts in the Mississippi River beneath the existing bridge structure. Drilled shafts were constructed to depths of approximately 200ft in alluvial soils using a rotator system with full-length segmental casing, and base grouted to improve axial resistance. This paper describes the design and construction of the work platform to provide access to the restricted-access site beneath the existing bridge, the approach used to construct the drilled shafts, and the results of a load test program to verify the axial resistance.

Jan 1, 2010

By D. Y. Peng

A Large Sub-structure with open top of S.Y.P. float line requires a 90m x 50m in plan and 13m-deep excavation in soft soil, Shanghai. The geological conditions in site are rather severe. The technology specifies that no permanent braces nor partition walls are allowed to be constructed inside. After a series of discussions the scheme of semi-gravity type cellular D-walling without any braces or earth anchors is finally adopted and successfully executed by SFEC. This paper deals with the technical problems in the design, construction and in-situ monitoring we met with in this difficult project.

Jan 1, 2010

By Lance Rasband, Richard Hanke

"Seattle Tunnel Partners (STP) started mining on Seattle’s SR99 tunnel on July 30, 2013, working slowly through a 15 ft (4.6 m) thick fiber-reinforced concrete headwall. Once through the headwall, the machine would move through roughly 400 lineal ft (122 m) of jet grout-improved soil at a rate slightly over 6 ft (1.8 m) per day. It was anticipated that once through the improved area, Bertha—the world’s largest tunnel boring machine—would move at a rate of 35 ft (10.7 m) per day. By the end of October 2013, Bertha had mined roughly 430 ft (131 m), averaging 4.73 ft (1.4 m) per day, and had begun mining within native soils. By the start of December 2013, tunneling reached the 800 ft (244 m) mark and Bertha averaged 12 ft (3.7 m) per day, achieving as much as 42 ft (12.8 m) of progress on some days. However, on December 6, 2013, Bertha began to stumble and all progress quickly came to a halt. Preliminary InvestigationInitial reports stated that an obstruction had stopped the machine in its tracks. Malcolm Drilling received an early morning call on Sunday, December 8, 2013, from STP to rapidly mobilize a Bauer BG-50 drill rig with crews to investigate what was hindering Bertha’s progress. Malcolm’s equipment and crews flew into action and were completely mobilized and operational by mid-week. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic head within the ground around the machine and allow STP personnel to inspect the cutter head from within the shaft for presence of obstructions. By the close of December 2013, the wells were installed and the dewatering system was fully commissioned. STP crews were then able to inspect the cutter head and found small fragments of a steel pipe wrapped around the outside of the shield. The steel was apparently from an abandoned 10 in (0.25 m) diameter monitoring well casing previously installed by WSDOT (Washington State Department of Transportation) to monitor groundwater conditions for the design and planning of this very project. After the steel was cut out of the head and cleared from Bertha’s path, she attempted to move forward but was only able to manage a slow crawl"

Jan 1, 2015

"The Metropolitan St. Louis Sewer District (MSD) in Missouri, the country’s fourth largest sewer system, is upgrading its storm and wastewater infrastructure in a 23-yearlong, $4.7 billion initiative called “Project Clear.” Historically, during times of intense precipitation, the current sewer system becomes overwhelmed. The primary goals of this project are to improve water quality and to alleviate many wastewater concerns in the St. Louis region by planning, designing and building community rainscaping, system improvements and an ambitious program of maintenance and repair.Part of the system renovation has focused on constructing underground tunnels for storm water storage, permitting controlled drainage of runoff, and preventing overflows into rivers and streams. Construction plans for these storage tunnels called for eight vertical intake and ventilation shafts to be bored from the ground surface. These shafts will then be intercepted in the bedrock at a depth of about 150 ft (45.7 m) during the excavation of the 3,000 ft (915 m) long underground tunnel that will be about 28 ft (8.5 m) in diameter. According to John Deeken , a geotechnical engineer with Black & Veatch Corp. and construction manager for the Maline Creek project, the drilling and blasting technique for creating the shafts was ruled out because the project was located in a residential neighborhood. “We could have used rock coring or a cutter head, but the drop shaft for this project is constructed within 10 ft (3.05 m) of an existing 108 in (274 cm) diameter sewer main,” Deeken said. “We had to take precautions to avoid damage to it.”A primary planning mandate of all MSD Project Clear phases requires minimized impact on traffic and residents. The canister drilling method enabled work to be confined to the median of a residential boulevard running perpendicular to the side street without detouring traffic. In addition, canister drilling offered a highly-precise means to create the shafts, leaving a smooth-sided borehole, right on target. Ground conditions in this 132 in (3.35 m) diameter intake shaft were wet due to the high groundwater levels and close proximity to the Mississippi River. “They’ve been finding shale in 2 to 6 ft (0.6 to 1.8 m) layers between weathered layers of Mississippian limestone,” said Dan Spiecher, technician at Center Rock (CRI). “The 2 ft (0.6 m) layers we can punch through. The 6 ft (1.8 m) layers slow us down.”"

Jan 1, 2017

By Scott A. Walker, Gabriel J. Alcantar, Brian Zuckerman, Ramin Golesorkhi

"The stadium development consists of construction of a 68,500-seat, open-air NFL football stadium for the San Francisco 49ers. The main structure will consist of a 7-story above grade steel structure supported by over 3,000 piles. Berkel and Company Contractors, Inc. (Berkel) was selected as the design-build pile contractor who used their auger pressure grouted displacement (APGD) piles for this project. During an indicator pile installation and pile load test program, fifteen piles were tested to develop installation criteria to support demands of 150kips tension and 180 kips compression. Following the indicator pile program Berkel installed 3088 piles in 30 working days. Throughout pile installation data were collected with an automated data acquisition system (DAS). During pile installation field engineers from Treadwell & Rollo observed the pile installation as well as the real-time data from the DAS. Strategic staging and pre-production planning by Berkel along with consistent collaboration with the design team created an atmosphere for a successful and on schedule project completion.IntroductionThe new San Francisco 49ers Stadium in Santa Clara, California will be a 68,500-seat facility, a rendering of which is shown in Figure 1. The main structure will consist of a 7-story above grade steel structure supported by more than 3,000 piles. The north, east and south portions of the stadium are designed as an open seating bowl, while the western portion includes open seating at the lower levels and seven-story tower which houses over 150 suites.The stadium project includes the stadium structure, as well as elevated open pedestrian walkways, commercial community space, and three new pedestrian bridges spanning a nearby by creek. Sustainable designs and innovations such as a green roof, photovoltaic panels, a ground source geothermal system, stadium-wide Wi-Fi capability, and access to public transit are provided throughout the project. The stadium is designed as an open, light, and airy structure and is surrounded by an existing amusement park, office buildings, the Santa Clara Convention Center, and the training facility of the 49ers."

Jan 1, 2015

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano, Shinya Tachibana

"The helical piling system provides solution to many geotechnical related problems due to its quick installation, higher compressive and pullout resistance, no wastage of material, workable in limited areas and reusability. However, its use as a foundation for bridges and high-rise buildings is still limited as compared to other piling methods. In the present study, the performance and load settlement behavior of screw and straight pile is investigated under cyclic compressive load in dense ground conditions. To achieve the set objectives, pile load tests were conducted in a cylindrical steel container. The model ground was compacted with dry sand at relative density of 80%. It is observed from the test results that screw and straight pile resistance reduced when the cyclic load is applied at allowable pile resistance state. The reduction in the ultimate pile capacity is more in straight pile than in screw pile. However, straight pile showed higher ultimate pile capacity than screw pile under similar pile tip diameter. The effect of helix bending deflection on load settlement behavior and ultimate pile capacity increases under cyclic loading.INTRODUCTIONScrew pile is one of the new developments in deep foundation, which is growing tremendously fast because of its quick installation technique, less noisy operation, no wastage of material and involvement of minimum manpower. Screw piles have an edge on straight pipe piles due to its high bearing capacity and uplift resistance. The installation mechanism of screw pile is different from straight pile. Torque and pressure is required to install the screw pile whereas hammering, pressure and vibration is required to install straight pile. As the installation mechanism is different between screw and straight pile, therefore, the ground disturbance that is produced during their installation is also different. The ground disturbance produced during the installation also depends upon the pile tip condition i.e. open or closed ended. Sakr, (2009) stated that the compressive capacity of screw pile in 3 to 5 times higher than driven piles having the same shaft diameter and length. The reason for this increase in pile capacity is due to helix, which is generally 2 to 2.5 times the pile shaft diameter. Larger helices can give higher end bearing capacity but it requires very powerful machinery to install in dense grounds. For instance, if large helix screw pile is installed in a dense ground then helix-bending deflection will start affecting the end bearing capacity (Yttrup and Abramsson, 2003; Malik et al. 2013 and 2015). According to Malik (2015), the equations of thin plate (Young and Budynas, 2002) with uniformly distributed load on the plate can give reasonable estimation of helix deflection due to dense ground conditions."

Jan 1, 2016

By Paul C. Schmall, Kevin Clarke, Paul J. Lewis, John M. Stanbury

"The $200M rehabilitation of the more than 100-year-old Gowanus Flushing Tunnel and pumping station located on the Gowanus Canal in Brooklyn, NY required deep excavations in an extremely congested urban environment. The environment posed significant challenges, including: support of excavation for protection of existing structures, excavation through man-made fill while eliminating groundwater inflow due to potentially contaminated groundwater chemistry; discharge and disposal impacts; and potential settlement of surrounding structures. This paper will present the design and construction challenges associated with the construction of a new combined sewer overflow (CSO) chamberwhich included a jet grout bottom seal, to mitigate groundwater inflow during excavation. The foundation for the finished structure also included a unique system incorporating the jet grout bottom seal elements with deep jet grout columns (piles) acting as the foundation system for the final structure. Design and construction challenges included highly variable soil conditions such as man-made fill, obstructions from previous construction, presence of an organic stratum, and conflicts with existing timber foundation piles. The jet grout bottom seal was constructed in loose sands with the deeper jet grout foundation elements extending to bear on a dense sand stratum. Challenges associated with the bottom seal included grid spacing and construction sequencing. Wet in wet sequencing was used to mitigate potential windows in the bottom seal further complicated by shadowing from existing timber foundation piles.Introduction And BackgroundModernization of the Gowanus Tunnel Pumping System required deep excavations in the extremely congested urban environment of Brooklyn, NY. The project location is shown on Fig. 1 and 2. The focus of this paper is to present the design and construction challenges associated with the support of excavation, control of groundwater, and ultimate foundation support for the combined sewer overflow (CSO) bypass chamber extension. The project site was tightly constrained by adjacent, active roadways and underground utilities, as well as residential and industrial structures. Therefore, excavation support was required to limit ground movement and maintain the integrity of the surrounding facilities. Excavation depths to as much as 16 ft below ground level, 8 ft below groundwater, required that seepage and groundwater be controlled so as to minimize pumping and disposal of groundwater and maintain the surrounding groundwater levels to avoid potential settlement of adjacent roadways, utilities, and structures. In addition, the subsurface conditions required that the proposed CSO bypass chamber extension be supported on a deep foundation to avoid differential and total settlements that may be detrimental to the existing and expanded structure. A plan view of the existing CSO bypass chamber and the proposed extension is shown on Fig. 3."

Jan 1, 2016

By Arash Khosravifar, Ali N. Ibrahim

"Large areas of Iraq are covered with collapsible soils namely gypsiferous soil which is often used as the foundation soil for structures. In particular, the Mosul Dam foundation is comprised of high contents of gypsiferous soils. Intrusion of water through the foundation soil dissolves gypsum which acts as the binding material between soil particles. This phenomenon results in the formation of collapsible soils which can cause serious damages to the dam structure. The failure of Mosul Dam, with a reservoir as large as 11 billion cubic meter of water, can be catastrophic. In the past, Mosul Dam Authorities have been remediating the soil foundation by injecting cement mortar. This method has been proved not economic; therefore, new, more efficient, methods are desperately needed.This research study focuses on finding practical methods to remediate collapsibility of gypsiferous soils by improving their geotechnical properties. This study presents remediation of collapsible gypsum-rich soil by grouting. Three types of stabilizer materials were used to make the grout; (1) sodium silicate (Na2 O3 Si) which is a well-known chemical soil stabilizer, (2) bentonite slurry, and (3) silicone oil. The purpose for using these stabilizer materials is to provide an impermeable layer (waterproofing coat) around the gypsiferous soil particles and to fill the voids that may occur in the soil as a result of gypsum dissolution when subjected to water.A series of double oedometer (collapse) tests and direct shear tests were carried out on gypsiferous soils before and after remediation by grouting. The results show that the soil compressibility decreases in the grout-treated gypsiferous soil by reducing volumetric strain. Consequently, the potential for collapsibility decreases too. It was also shown that grouting, increases the shear strength of the soil at confining stresses smaller than 250 kPa by increasing the cohesion combined with a slight reduction in the internal friction angle.INTRODUCTIONGrouting is one of the ground improvement techniques which is often used to improve the loose foundation soils. Bruce (2003) provides step-by-step procedures on using grouting techniques for sealing dams and other water reservoirs. Grouting can be classified as permeation grouting, compaction grouting or hydraulic fracturing. Permeation grouting is an effective way to send the grout into the ground without disturbing the soil structure, i.e. free flow of grout into the soil voids where grouting is accomplished by injection of a fluid-like material that is capable of forming a gel and binding the soil particles together. Grout materials may be solution grouts or suspension grouts. The permeation grouting technique is generally used to minimize ground permeability and to control ground water flow, but it can also be used to strengthen and harden the ground (Raman et al., 2012)."

Jan 1, 2017

By Sunil S. Basarkar, Vinothkumar S

Ground Improvement Techniques serves to improve various engineering properties for supporting various foundations. These may be undertaken either by conventional or advanced methods. The Controlled Modulus Column (CMC), also known as Rigid Inclusion is a soil improvement technique to reduce the total and differential settlement by using semi-rigid soil reinforcement columns. The CMC technique can be executed by displacement or non-displacement methods. It does not aim to bypass the compressive layer or to install a pile that will directly support the entire load from the structure. Principle of the technique is to introduce a load transfer platform between the head of the column and structure and transform a uniform load into soil. Initially, the structural load transmitted into the soil generate the settlement greater than CMC piles. When the settlement between the soil and column became equal at neutral point, maximum structural load shall be balanced by the positive friction and tip resistance to stabilize the foundation without exceeding the allowable settlement limit. This paper describes the behaviour of soil reinforcement with CMC column and their installation process with reference to a project at the Dry Bulk Terminal Port, San Pedro- Abidjan (Western Africa). Methodology of CMC, requirements of Ground Improvement, arrangements and outcome of this method are presented in this paper.

Sep 1, 2022

By K. Madhusudan Reddy

"Pile response under combined uplift and lateral load is very important and it is imperative to evaluate the effect of combined loading and only few studies were reported on pile behavior under combined uplift and lateral loads. Model pile made-up of aluminum having an outer and inner diameter of 25.4 mm and 19.4 mm respectively is used. Dimensions of the model steel tank are fixed as 1.0 m x1.0 m x 1.2 m (depth) to avoid the boundary effects under combined lateral and uplift loads. Experiments were carried out on single piles at isolated uplift, isolated lateral loading and combined lateral and uplift loading, embedded in sandy soil. Results indicate that load–deflection behavior is nonlinear for isolated uplift and lateral load tests as well as in case of combined loadings. It is also observed that the behavior of piles under isolated loadings is substantially different when compared to combined loading.INTRODUCTIONPile foundations are generally used to support compressive loads from superstructures. Some structures, like transmission towers, mooring systems for ocean surface or submerged platforms, tall chimneys, jetty structures, etc. are constructed on pile foundations, which have to resist large lateral and uplift loads and moments. The various loads (compressive, lateral and uplift) and moments act on the piles simultaneously rather than isolated manner. There are well-established theoretical methods present to evaluate the pile behaviour under different isolated loadings namely, verticalcompressive, vertical-uplift and lateral (Poulos and Davis, 1980), but there are very limited studies focused on pile behaviour under combined loadings. Though there is good number of studies reported on pile behaviour under combined compressive-lateral and compressive-uplift loadings (Ramasamy, 1974; Jain et al. 1987; Zhang and Small, 1999; Dash and Pise, 2003; Karthigeyan et al. 2006 & 2007; , there are only very few studies reported on pile behaviour under combined uplift and lateral loads. Darr et al. (1990) described an approach to a rational solution of the interaction of pile to combined uplift and lateral loads based on analytical and experimental studies. Influence of cyclic loading was also considered. Narasimha Rao and Prasad (1993) investigated the uplift behaviour of pile anchors subjected to lateral cyclic loading. There were many onshore and offshore situations where lateral cyclic loading may affect both the pullout and lateral loading capacity of pile anchors. Jetty and wharf structures are usually subjected to lateral forces from wave and wind action. If these cyclic lateral loads are acting on the supporting piles, the resulting movement of the upper part of the embedded length of pile may reduce the skin friction. This progressive deterioration in pullout resistance may not be reflected by a pullout test made soon after the installation. Hence, Tomlinson and Woodward (2008) pointed out that a generous safety factor on the ultimate pullout load should be adopted for piles in such situations. Mroueh and Shahrour (2007, 2008) presented a threedimensional finite element analysis of the response of battered piles to the combined lateral and vertical pullout loads. Nevertheless, the model is not validated well due to lack of good experimental data based on rigorous experiments. Thus there is a scope for investigating the effect of lateral load on pile behaviour under uplift load and vice versa based on carefully designed experiments, which is main focus of the present investigation."

Jan 1, 2017

By T. Wulleman, M. Ansriou

Integrity testing is a primary quality control check on a product that is for the most part not accessible to visual examination. Their cost can be expensive when using direct methods of inspection (like coring a pile) or more economical when using indirect methods (e.g. acoustic testing). All indirect methods operate by “inference” which means that they do not directly measure the defect of integrity. Indirect methods measure the variation of physical values (temperature, impedance, speed, ect.) correlated to the integrity of the pile allowing the detection of integrity defects, although these methods do not allow for the characterization of the defect. 1. INTRODUCTION Cast-in-place piles are particularly prone to integrity defects. The reasons for this are multiple, including lack of high quality of contractor workmanship, experience and supervision necessary in construction, variable soil and groundwater conditions on site, etc. Furthermore, visual inspection of the finalized pile is usually impossible. Therefore, special care has to be taken both during the execution process and during the subsequent quality control campaign to detect any defects of executed piles. Today, a lot of methods do exist to assess pile integrity. It is thus essential to understand the mechanism governing those devices to both make an engineering choice of the pile integrity testing method and to interpret correctly the provided results. 2. QUALITY IN PILE FOUNDATIONS 2.1 Pile anomalies A pile having an anomaly is a pile which has a different behavior from what is normally expected. The presence of a pile anomaly does not necessarily imply that a pile cannot be used for its intended purpose (Gordon & Chapman 2004). An anomaly can be considered as a defect, or a “performance” depending on the ability of the pile to fulfil the following three criteria (3C): C1 - Meet the Service Limit State (SLS) requirement and support the proposed working load without settling more than admissible by the superstructure ; C2 - Meet the Ultimate Limit State (ULS) requirement and carry a specified load with an adequate factor of safety against failure ; C3 - Remain durable throughout the design life of the structure such that the pile is not affected by time dependent activities (chemical attack, corrosion of steel reinforcement, ect.), which would jeopardize its ability to maintain its compliance with the first two criteria.

Jan 1, 2019

By Shreya Vivek Hokam, Dr. A. I. Dhatrak, S. W. Thakare, Dr. Vivek S. Hokam

Construction in congested urban areas has necessitated tall and massive structures. In urban areas, it is common to construct underground structure nearby existing buildings. Selection of an appropriate support structure system to be implemented in the excavation in an urban area is heavily dependent upon the geotechnical conditions and safety of the surroundings and neighbouring structures. Urban Rail, popularly referred to as Metro Rail, has seen substantial growth in India in the recent years. More cities are experiencing the need for metro rail to meet their day-today mobility requirements. The metro structures involved deep excavation for foundations which induces the stresses and thereby alters the existing equilibrium and thus may affect stability of neighbouring structures considering safety point of view. Hence, design and execution of deep excavations become one of the important challenging tasks of any geotechnical engineer in the modern era. Further, it is important to control the ground movement in order to prevent the failure of excavations. This involves specialized foundation technologies, usage of sophisticated equipment and new methods in underground construction, safety and monitoring systems. In this paper the methodology used for protecting adjoining structures due to deep excavation for Nagpur Metro station is studied.

Sep 1, 2022

By Georg Breitsprecher

The technique of Stabilising Columns (product names are for example "Stabilisierungssaulen" (STS) or "Coplan Stabilisierungs-verfahren" (CSV)) is gradually becoming well accepted for ground improvement. The installation, dimensioning and quality control are standardized by DGGT (German Association for Geotechnique), working committee 2.8, of which until now only part one exists for dry columns. This paper describes the installation and testing of stabilising columns for a ground improvement project. To achieve comparable results in testing both ready mixed concrete and dry binder had been used for production.

Jan 1, 2006