Search Documents

By S. P. Cashin, D. Kashuba, W. Esplin

Barrick has had 6 autoclaves in operation at the Goldstrike Mine, North of Carlin Nevada, since 1993. The 6 autoclaves operate in parallel, processing slurry of gold ore. The gold in the ore is predominantly associated with, and encapsulated by, sulphide minerals. It is necessary to oxidize at least 90% of the sulphide mineral before the gold can be concentrated using a cyanide/carbon-in-leach (CIL) circuit. Sulphide oxidation chemical reactions occurring in the autoclaves are exothermic; however, the sulphide content in the ore is not high enough to operate the autoclaves in an auto-thermal mode. Heat from steam is added to the first 2 of 5 autoclave compartments to initiate the sulphide oxidation reactions. The steam used to heat the autoclaves is supplied by three boilers, which are fuelled with propane gas. The completion of a few operations and maintenance projects in the last 2 years has resulted in a 50% reduction in propane energy requirements. The autoclave operating temperatures were minimized. Excess oxygen addition was held as low as possible. The material of construction for the compartment walls inside the autoclaves was changed from brick to Titanium metal. And, the speed of the autoclave slurry agitators was increased. All of these activities had an impact on the propane energy requirements of the autoclaves. Presented below is a description of the autoclave systems, and a discussion of how the energy needs were reduced, resulting in significant operating cost savings.

Jan 1, 2004

By T. T. Tigert

INTRODUCTION THE PURPOSE of this article on methane is to present the simple basic facts of the characteristics, detection, occurrence, and control of this natural gas in metal mines, so that operators and .safety men may deal with it with some degree of confidence. Fortunately, although methane has been noted at many metal mines throughout Canada, the occurrences usually are small flows of short duration, and the ignitions experienced have, in most cases, had minor consequences. However, methane does present a hazard that can be of serious proportions, and ?any complacent attitude toward this gas that might exist in the minds .of people engaged in underground mining operations should be dispelled when it is ,pointed out that, in Ontario alone, ignitions of this gas have resulted in at least four fatalities, and eight men seriously injured and burned, during the past three years. lt is well-known that liberation of methane can and does .occur suddenly, often in mines where no gas has been found before, and that many ignitions and explosions have occurred in so called non-gassy mines. In view of this, it is apparent that no mine can, with any degree of certainty, be classified as non-gassy. CHARACTERISTICS OF METHANIZ The characteristics of natural gas encountered in most of the Ontario mines indicate that methane is the chief constituent. Methane (CH4), commonly termed 'marsh gas', and by the coal miner 'firedamp', is a colourless, odourless, and non-poisonous gas considerably lighter than air, and is the explosive gas frequently found in coal mines. Its physiological effects, closely resemble those resulting from nitrogen.

Jan 1, 1951

By Eduardo R. Rodrigues, Ankur Narang, Roberto Federico Ausas, U. T. Mello, Jose Maria Segura Serra, M. R. Lakshmikantha, Ignacio Carol, Kamal C. Das

"Modeling of big faults or weak planes of strong and weak discontinuities is of major importance to assess the Geomechanical behaviour of mining/civil tunnel, reservoirs etc. For modelling fractures in Geomechanics, prior art has been limited to Interface Elements which suffer from numerical instability and where faults are required to be aligned with element edges. In this paper, we consider comparative study on finite elements for capturing strong discontinuities by means of elemental (EFEM) and nodal enrichments (XFEM) for Geomechanical applications. For general fracture scenarios, Oliver et al. (2008) have demonstrated advantages of EFEM over XFEM for including: (a) ease of modeling in any standard finite element code due to the possibility of static condensation, (b) higher accuracy in some cases for coarse meshes, and, (c) a reduced computational cost. However, there has been no work that considers cohesive fractures in Geomechanics. We present a numerical analysis based on a linear constitutive model and linear triangular elements for the bulk and a linear constitutive behaviour for the fault for a representative set of fault planes in a circular tunnel made in rock mass. In the numerical examples we consider both well-traced and bad-traced meshes. We focus on traction profile analysis for both EFEM and XFEM, since that is crucial to understand the cohesive fracture behaviour specially rock joint. Therefore in each case, shear, normal and stress ratio are compared across the two methods along the fault plane. This is the first such work that compares XFEM and EFEM behaviour for Geomechanics problems.For the considered class of problems and the sharp penalization approach without regularizations adopted, it can be observed that accuracy and robustness of EFEM may strongly depend on the fault orientation with respect to the element edges, while, XFEM is independent of fault alignment with element edges. It has been also observed that, with mesh refinement model, stress oscillation completely removed with XFEM however EFEM fails to provide oscillation free results with finer mesh in case bad-traced model. We also performed error analysis and found that in case of bad-traced mesh the average error in the XFEM is 84% smaller than of EFEM and for XFEM the error goes to zero with increasing mesh resolution, while for EFEM the error increases with mesh resolution. Thus, we experimentally demonstrate that, XFEM performs better than EFEM in terms of accuracy and rate of convergence with marginal increase in computational cost. This work hence provides novel insights on the application of XFEM and EFEM in Geomechanics."

Jan 1, 2015

By G. D. Markland

"The Moose Mountain mine is located in a belt of Precambrian volcanic rocks situated 20 miles north of Sudbury, Ontario. It was the first iron mining operation in the Archean iron-formations of the Canadian Shield.The ore is believed to have been formed in an environment of active volcanism, being part of a pyroclastic and volcanic series where only the iron-formation and chert qualify as chemical sediments. The volcanic environment, subsequent regional tectonics and metamorphism produced orebodies which differ from the main sedimentary iron ranges of the world in such features as continuity, grade, structure and metallurgical characteristics. The orebodies occur as relatively small lenses which have been complexly folded, faulted and intruded by acidic and basic dykesAlthough the basic mining and beneficiation methods are simple, detailed geological control in exploration, planning and operation has been necessary to apply detailed selective techniques to the large-scale open-pit methods necessary in profitable iron mining.The milling and pelletizing processes are sensitive to minor variations in ore grade, grain size, fabric and mineralogy. Although detailed correlations of geological information and mill performance are still not entirely satisfactory, general working relationships have been determined with simple testing procedures. These are of in-creasing use in forecasting production and in ore-blending processes.The application of geology to mining and milling operations at Moose Mountain represents a departure from general practice in iron ore operations."

Jan 1, 1966

By Farzad Khodabakhshi, Adrian P. Gerlich

"In this article, cold spraying process was utilized to coat the surface of AZ31 magnesium alloy with a layer of AA7075 aluminum alloy. Thereafter, friction-stir processing (FSP) was employed to enhance the microstructure and consolidate the deposited layer. The grain structure and phase morphology were studied along with indentation hardness before and after cold spraying and friction stir processing. The magnesium substrate had an initial hardness of 74 HV which increased to 102 HV after FSP due to refinement of grains to <2 µm. The aluminum coating layer, provided improved surface hardness up to 160 HV, which further increased to 173 HV after FSP was applied.INTRODUCTION Cold spray is a material deposition process which can be used for surface modification, since it deposits material on a metallic substrate with little heating by way of high velocity ballistic impacts. Using cold spray technology, it is possible to deposit a wide range of coatings with various thicknesses by controlling the characteristics of the feeding powder and metal substrate, gas temperature, gas pressure, powder feeding rate, nozzle geometry, and gun traverse velocity. This process has been recently employed for surface modification in various aircraft and automobile structural applications. This has led to a broad range of research using this process for production and modification of different metallic and non-metallic systems. In the present study, cold spray process was used to deposit a uniform layer of aluminum-zinc alloy (AA7075) on the surface of AZ31 magnesium alloy. This coating was subsequently treated by way of friction-stir processing (FSP) as a new post-spraying modification technique to enhance the structural homogeneity and densification of the coated aluminum layer. This method utilizes a non-consumable rotating tool with a specially designed shoulder and pin that is plunged into the surface of metal to be modified and then moved along the direction of interest. The localized frictional heating between the rotating tool and workpiece leads to softening of the materials around the pin, and material extrusion through a complex flow of material from the advancing toward the retreating side the tool. To the author’s best knowledge, only a few reports discuss the modification of a cold sprayed deposit by FSP process. The microstructure and mechanical properties of the cold sprayed layer and substrate before and after FSP modification were examined using optical observations (OM) and indentation hardness testing. Furthermore, the AZ31 alloy substrate alone was treated with FSP as well, for the aim of comparison to the processed coating."

Jan 1, 2017

By S. A. Pence, A. I. McCallum, V. de Korompay

"Special salt protection rings containing a water-swell• able, polymeric sealant are in successful operation in Canadian potash shafts. Installed above the Prairie Evaporite salt formation at a depth of 3,000 feet, the sealant is preventing formation water migration into the salt and pressure build-up on the concrete lining of both production and service shafts. The salt protection rings are not under the hydrostatic pressure of the formation water.The chemical sealant in use has the unique property of imbibing water and swelling. •Therefore, any water at• tempting to flow by the seal ring actually produces a tighter seal.The purpose of this paper is to discuss the sealant and its properties and uses. Installation of the material and its operation in two Canadian mine shafts is described."

Jan 1, 1971

Pilot plants for pressure hydrometallurgy represent special design and project execution challenges unique to the industry and to the pilot- and demonstration-scale. Pilot plant projects have different objectives and shorter timescales than commercial plant projects. Design considerations and strategies, and project execution methods that meet the special needs of pilot plant projects, are discussed. Specific guidance is given for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical process equipment, and for the selection of materials of construction for pilot-scale equipment. The balance between the need for process similarity with future commercial operations and the realities of pilot-scale equipment is also discussed.

Jan 1, 2004

By G. W. H. Norman

INTEREST in the mineral possibilities (gold, copper) of northern Quebec, north of the Quebec-Cochrane branch of the Canadian National railway, has centred for many years in the Chibougamau district (see Figure 1). Since 1934, however, promising gold discoveries in the Rose Lake-Florence River section, 115 miles southwest of Chibougamau lake, have widened the interest, and prospectors have examined other parts of the country between Chibougamau lake and Bell river and the surrounding districts. The object of this paper is to !resent an outline of the geology, and to describe the mineral deposits, o part of this region, or, more specifically, of the part embraced by the Opawica-Chibougamau and Waswanipi map-areas(l), which include the districts about Chibougamau lake and Rose lake-Florence river, where mineral deposits are now in course of development either by surface or underground work. Early discoveries, developments, and explorations in the Chibougamau district are well summarized in the report of the Chibougamau Commission, published in 1911(2). The Commission discredited previous optimistic accounts of mineral discoveries in the area, made initially in 1903, but at the same time they expressed the opinion that, from a geological standpoint, the district promised a reward to diligent and intelligent prospecting. Their general conclusion-that prospecting in the area was not then (1911) commercially advisable in view of its inaccessibility and other handicaps shifted interest from the district until, some years later, valuable discoveries were made in the Rouyn area, and aircraft widened the field of successful exploration. During the past ten years or so, considerable energy has been spent in promoting the development of the district. The net result has been the discovery of a number of prospects, the majority of which have been explored only by trenching and, in most cases, diamond drilling.

Jan 1, 1936

By G. D. Markland

The Moose Mountain mine is located in a belt of Precambrian volcanic rocks situated 20 miles north of Sudbury, Ontario. It was the first iron mining operation in the Archean iron-formations of the Canadian Shield. The ore is believed to have been formed in an environment of active volcanism, being part of a pyroclastic and volcanic series where only the iron-formation and chert qualify as chemical sediments. The volcanic environment, subsequent regional tectonics and metamorphism produced orebodies which differ from the main sedimentary iron ranges of the world in such features as continuity, grade, structure and metallurgical characteristics. The orebodies occur as relatively small lenses which have been complexly folded, faulted and intruded by acidic and basic dykes.

Feb 1, 1966

By K. C. Hendrick

The paper will review the significant developments in world copper over the past ten years and their impact on the Canadian industry. It will also examine the outlook for the future.

Jan 1, 1971

By C. S. Ha, H. S. Choi, D. Y. Shin

POSCO installed a new 100 ton oxygen bottom-blown converter in 2013 for the development of new steelmaking process named as PS-BOP which is reading POSCO-Saarstahl Basic Oxygen Process. This process was developed by the collaboration research between POSCO and Saarstahl AG in Germany that is based on substantial increase of CO post combustion in a converter by blowing hot air from the top of converter. The collaboration research has been finished successfully in November 2013 with 17% decrease in hot metal ratio (HMR) when hot air was blown from the top of the oxygen bottom-blown converter. After the collaboration research the converter has been tried to be operated as oxygen top and bottom-blown converter to reduce bottom wear and to decrease production cost with increased use of low cost Fe source by the help of increased CO post combustion. The presentation includes experience on the start up of oxygen bottom-blown converter, HMR reduction trials with hot air top blowing and transition from oxygen bottom-blown to top and bottom-blown converter operation.

Jan 1, 2015

By H. C. Gunning

In spite of the fact that mining has been more or less active in the northern part of Vancouver island since the late &apos;nineties&apos;, there seems to be a remarkable lack of information regarding the nature and development of the region. Recently the operations at the Old Sport mine of the Coast Copper Company, Limited, and spectacular copper discoveries in the vicinity of Nimpkish lake, have directed the attention of the mining fraternity to the district. The writer spent the summer of 1929 making a reconnaissance examination of the general geology and mining properties of the area between Quatsino sound and Nimpkish lake, and he feels that a short paper describing the nature and mining possibilities of the region should be of interest at this time. A more detailed account of the ?geology and of the mining properties will be published in the forth- coming Summary Report of the Geological Survey. A short paper dealing with the Nimpkish Lake district was presented at the Annual Meeting of the British Columbia Division, held recently in Vancouver.

Jan 1, 1930

By J. T. Fyles, C. G. Hewlett

"THE REEVES MACDONALD mine is in the Sa Imo-Pend d'Oreille mining area of southeastern British Columbia. It is on the Nelway-Waneta road 4 miles west of the border-crossing point of Nelway. The Reeves orebody from which all production has come is one of several mineralized zones in easterly-striking limestones occurring between the Pend d'Oreille and the lower part of Salmo River.The property was originally located as two groups of claims by R. M, Reeves and J. H. McDonald. The two groups were consolidated in 1925. and extensive development work was done from then until 1930 and again in 1937, but no ore was shipped. The mine was reopened in 1947 and, between 1949 and 1953, 1,057,804 tons of ore was mined. Concentrates recovered contained 85,626 ounces of silver, 19,394,092 pounds of lead, 72,076,495 pounds of zinc, and 455,051 pounds of cadmium. Low metal prices forced the mine to close in 1953, but operations were resumed in November, 1955.The orebodies at the Reeves MacDonald mine are steeply plunging lead and zinc sulphide replacement deposits in a banded limestone named the Reeves limestone. The orebodies contain pyrite, honey-coloured sphalerite, and galena, and are surrounded by a dolomitized zone. In the Reeves orebody, where the relationships are known, the dolomite has the same general shape as the orebody. Four zones of sulphides are known on the property (see Figure 1). Three of these, the Reeves, B. L., and O'Donnell, are believed to be faulted segments of one mineralized zone. The fourth, the Point ore zone, exposed on the north bank of the Pend d'Oreille River, is not developed and its structural position is not known, but it appears to be a separate deposit."

Jan 1, 1949

By Eiichi Sato, Koichi Kitazono, Hiroshi Masuda, Kenta Higane

"The present study investigated the low-temperature creep mechanisms in ultrafine-grained (UFG) aluminum manufactured by accumulative roll bonding. UFG aluminum with grain size 0.39 µm showed steady state creep even at room temperature under low stresses as confirmed by the creep curves in the strain rate–strain plot. The low-temperature behavior was divided into four regions by three distinctive stresses, sI, sII and sIII: sI (=45 MPa) is denoted as the micro-yielding stress with which dislocations start movement, sII (=85 MPa) the dislocation-multiplication stress above which dislocations multiply with creep deformation, and sIII (=171 MPa) the conventional yield stress above which macroscopic plastic strain is generated. During low-temperature creep, below sI, negligible plastic strain is generated. Between sI and sII, creep deformation with stress exponent 2.5 occurred, which is accommodated by dislocation absorption into grain boundary and grain boundary sliding, similarly to the low-temperature creep of HCP metals. Between sII and sIII, creep deformation with stress exponent 7.0 occurred, whose mechanism is similar to the low-temperature creep of coarse-grained aluminum. Above sIII, power-law breakdown occurred.INTRODUCTIONIt is well understood that the creep deformation brings about at high homologous temperatures (T/Tm) of >0.4, where Tmis the melting point, with diffusion processes. Recently, the importance of aluminum is increasing for cryogenic temperature parts such as a metallic liner or a cap in high pressure-hydrogen vessels, and the presence of creep behavior in aluminum at room temperature has become recognized (Matsunaga, 2013;Kassner, 2015).In HCP metals and alloys, especially intitanium, steady-state creep behavior appears at room temperature with apparent activation energy of1/10 of that for self-diffusion(Neeraj, 2000; Matsunaga, 2009).On the other hand, Kassner (2015) claims that aluminum shows creep behavior at room temperature with apparent activation energy of 4/5of that forself-diffusion, but never reaches the steady state. We should note that it is derived from the data obtained from short-term creep tests of few hour, and Matsunaga (2013) already claimed the presence of steady state in room temperature creep in aluminum with activation energy of 1/5of that for self-diffusion.The mechanisms for low temperature creep are considered different between HCP and FCC metals: in HCP metals, grain boundary sliding is observed and is thought to accommodate piled-up dislocations at grain boundaries through absorbing them. The so-called slip-induced grain boundary sliding occurs with low number of activated slip systems(Matsunaga,2009).On the other hand, in FCC metals, many activated slip systems bring about work hardening with dislocation cell structure formation. In the initial stage of creep, it results in primary creep (Kassner, 2015), but Matsunaga (2013) claimed that once the annihilating of a cross-slipped dislocation to another reaches balance, steady state is established. It has been, however, strongly required to show more convincing experimental verification for the presence of steady state in FCC metals at low temperature."

Jan 1, 2018

By C. R. Tang

Due to the current lack of sufficient occupational hazards supervisory staff in China, an occupational hazards supervision regulatory framework is proposed, based on the cloud. Data on respirable dust, noise, heat, toxic and hazardous substances and protection facilities are uploaded to private cloud computing data and service centers to build an occupational hazards supervision system. This system promotes occupational hazards governance. Complex reports are generated. Through the establishment of an occupational hazard supervision data threshold, the dynamic regulation of occupational hazards is accomplished. The main characteristics of this approach are low cost, ease of expansion and maintenance, and strong performance.

Aug 1, 2013

By D. W. Hayley

The rapid expansion of exploration drilling with anticipated production facilities for oil and gas in the Mackenzie Delta region of the Northwest Territories has created a demand for granular construction materials. This paper discusses the technique adopted and experience gained by the authors from several major resource evaluation programs in this remote area. The first part of the paper describes a methodology for deposit identification, logistics of helicopter and ground-based drilling operations and the sampling difficulties which are unique to permafrost: soils. The second part describes the exploitation of a large glaciofluvial deposit at YaYa Lake on Richards Island. Granular construction material is sparse in the delta region relative to projected demand. Exploitable sources of granular materials for aggregates or construction borrow are found in glaciofluvial deposits of Pleistocene age or in outcrops of Paleozoic bedrock. Glaciofluvial landforms can be located by reference to published surficial geology maps coupled with airphoto interpretation. Preliminary assessment of these features in a large region is most economically carried out during the summer months with a drill that is transportable by helicopter. Once prospective borrow pit sites are identified, a detailed ground-based winter drilling program must be undertaken to establish aggregate quality and quantity, and to provide information on natural features which could affect development. The glaciofluvial terrain has been highly modified by the formation of massive ground ice within the gravel deposits. This presents some unique pit development problems which are not encountered in a normal bedrock quarry operation.

Jan 1, 1977

By M. L. Wacker

"Cigar Lake high-grade uranium mine in Saskatchewan is operating after 25 years of test mining, construction, and mine flood remediation. Factors include ground stability, groundwater control, radiation exposure, and ore handling. A 10 year test program resulted in validating “jet boring”, a non-entry mining method involving artificially freezing the orebody and surrounding rock; tunnelling to develop access crosscuts below the orebody; installing cased pilot holes through ore; extracting ore using rotating high-pressure water jets within pilot holes; and cavity concrete backfilling. Ore slurry is prepared underground, pumped to surface, and trucked to McClean Lake mill for processing to uranium concentrate.RÉSUMÉ Après 25 années d’essais sur les méthodes minières, de construction et d’assainissement suivant les inondations à la mine, l’exploitation de minerai à haute teneur en uranium Cigar Lake, localisée dans la province de la Saskatchewan, est opérationnelle. Les principales difficultés concernent la stabilité du terrain, le contrôle des eaux souterraines, l’exposition aux rayonnements et la manutention du minerai. Un programme d’essai de 10 ans a abouti à la validation du « forage à érosion », une méthode minière qui consiste à congeler artificiellement le corps minéralisé et les roches environnantes ; à creuser des tunnels pour développer des travers-bancs d’accès en dessous du corps minéralisé ; à installer des puits de fondation pilotes à travers le minerai ; à extraire le minerai à l’aide de jets d’eau à haute pression dans les puits pilotes ; et à remblayer les cavités avec du béton. La boue de minerai est préparée sous terre, pompée vers la surface puis transportée par camion jusqu’à l’usine de concentration de McClean Lake pour le traitement afin d’obtenir du concentré d’uranium.INTRODUCTIONThe Cigar Lake deposit is in northern Saskatchewan, 660 km north of Saskatoon, Saskatchewan, Canada, at the east edge of the Athabasca basin (Figure 1; Bishop, Mainville, & Yesnik, 2016). The operation is jointly owned by Cameco Corporation, AREVA Resources Canada Inc., Idemitsu Canada Resources Ltd., and TEPCO Resources Inc. Cameco has been the operator of Cigar Lake since January 2002. The discovery hole was drilled in 1981. Commercial production was declared in May 2015 and the Phase 1 operation will have a mine life of 15 years."

Jan 1, 2017

By T. H. Chuang, Y. Y. Shiue

"Rapid whisker growth was significantly alleviated in a Sn-58Bi alloy doped with 0.5 wt.% La. Experimental results showed that many thin, plate-form intermetallic phases appeared in the solder matrix. The absence of tin whiskers was correlated to the shape effect of RE-containing intermetallic plates. After reflowing, Cu6Sn5 intermetallic compounds appeared at the solder/pad interfaces of Sn-58Bi and Sn-58Bi- 0.5La packages with OSP pads, which grow linearly during the aging at 75 and 100? for various times ranging from 100 to 1000 h. In addition, the interfacial intermetallics layers in Sn-58Bi-0.5La solder joints were also observed thinner than those in undoped Sn-58Bi joints. However, RE-containing interfacial intermetallic compounds in Sn-58Bi-0.5La solder joints led to lower bonding strengths in both ball shear tests (0.4 mm/s) and high speed ball shear tests (2000 mm/s). All the reflowed and aged solder joints of both packages were ruptured through the solder balls indicating brittle characteristic INTRODUCTIONIt has been widely reported that solder alloys doped with rare earth (RE) elements reveal many beneficial effects, such as higher strength, lower melting point, improved wettability, and longer creep life (Wu et al., 2004; Ma et al., 2002; Chen et al., 2002). In addition, Dudek et al. reported that the alloying with 0.5 wt.% La in Sn-3.8Ag-0.7Cu solders resulted in an increase of rupture strain, up to 150% over undoped solders (Dudek et al., 2006). However, Chuang and Yen observed that a large amount of long, fiber-shaped tin whiskers were extruded out of the oxidized CeSn3 intermetallic clusters in the matrix of a Sn-3Ag-0.5Cu-0.5Ce solder air-stored at room temperature for several days (Chuang & Yen, 2006). Furthermore, many coarse hillocks appeared around the CeSn3 clusters in the RE-doped alloy after storage in an air furnace at 150? for several minutes. Chuang proposed a mechanism for the phenomenon of rapid whisker growth, which the predominate oxidation of CeSn3 intermetallics in Sn-3Ag-0.5Cu-0.5Ce solders induced compressive stress and extruded the tin atoms out of the specimen in the form of tin whiskers (Chuang, 2007). However, further investigation showed that Sn-9Zn-0.5Ce solders, after long term exposure at room temperature and 150?, were immune to the whisker growth; the immunity was attributed to the refining of the CeSn3 intermetallic phase in the alloy (Chuang & Lin, 2008). The inhibition of tin whiskers through the refining of rare earth containing intermetallics was further observed in Sn-3Ag- 0.5Cu-0.5Ce solders doped with 0.5 wt. Zn (Chuang & Lin, 2009). In addition to the size effect, the thin plate shape of intermetallic compounds was also shown in this study to inhibit the whisker growth on the surface of Sn-58Bi-0.5La solders."

Jan 1, 2012

By Lawrence Bragg

WE associate metals with hardness, toughness, and strength. But a curious paradox lies at the root of the valuable mechanical proper-ties of the metallic state: in order to be strong, a metal must be weak. This paradox, and the equally surprising fact that, in a sense, metals are not true solids at all, are among the topics here discussed by Sir Lawrence Bragg. (1) WHAT METALS MEAN TO US We employ various materials to build or fabricate the many objects we use in everyday life, choosing those whose properties are most suitable for the purpose which the object has to serve. Certain of these materials have been used from the earliest times, such as stone, wood, leather, and animal or vegetable fibres, each with its own peculiar valuable properties. Stone resists crushing and is very durable and permanent, as indeed it must be, since it has so long resisted change as a part of-the earth&apos;s crust. It is there-fore ideal for walls and buildings, and very early in his history man discovered how to make artificial stones by burning clay, with the advantage that they could be given any desired shape, and made into bricks or given elaborate forms as pottery. Wood is strong and tough and light, it resists tension as well as compression, and is nor brittle like stone. It forms beams and furniture and parts of tools or weapons. Leather is tough but at the same time iris flexible; it is ideal as straps or sheers. Vegetable fibres such as linen or cotton, and animal fibres such as wool and silk, owe their value to their flexibility and strength in resisting extension. They can be spun into yarn or rope, and woven into cloth. The technological age in which we are now living is replacing the natural products used by early man by a series of artificial products, but it is remarkable to see how in nearly every case we are copying Nature&apos;s materials. The wide use of concrete represents a developed art of making artificial stone. Artificial fibres such as rayon or ?nylon replace cotton, wool, and flax. Plastics are coming very much to the fore; they correspond to early man&apos;s use of horn, another substance with peculiar properties of roughness in all directions without the &apos;grain&apos; of wood. For the most part we are following in the footsteps of our remote ancestors, though we can make for ourselves what they had to cull from wood and field. There are exceptions; for instance, we have discovered comparatively recently the number of uses to which natural rubber can be put, and are now making it artificially. This is a really new discovery; our ancestors had nothing with such remarkable powers of elastic stretching without breaking, and resistance to being abraded.

Jan 1, 1943

By T. Patching

"COAL MINING at Canmore, Alberta, began in 1886 and continued there until July 1979. A comprehensive review of the Canmore operations is not available, but the following notes have been prepared to accompany references where more complete information about the operations and problems encountered may be found. The coal measures at Canmore occur in the Kootenay formation of Lower Cretaceous age, and at least twelve seams of varying thickness and horizontal extent have been recognized. The coal, of high quality, ranges from semi-anthracite in the lower seams to low-volatile bituminous in the upper seams. The strata of the Canmore area form an asymmetric syncline, the western limb being overturned to vertical by the Palaeozoic strata of the Mount Rundle Range. The eastern limb is more gently sloping, its dip ranging from IO to about 40 degrees. Tectonic movements have created a troubled and complex coal field. The seams were initially not regularly or uniformly deposited, and mountain-building activity folded and faulted the strata and in many places sheared and crushed the original structures of the coal(l,2,3,4,5). The lack of continuity of the seams, and changes in thickness and inclination, made longrange mine planning difficult and necessitated flexible methods of work, and the local disturbances sometimes created problems in roof support and contributed to the occurrence of sudden outbursts of coal and gas. Almost all of the coal was produced from underground operations but a few relatively small V-cut mines were worked along surface outcrops. These have all been filled in and revegetated. The basic method of underground work was by room-and-pillar, but many variations in layout and sequences were employed. Gangways were driven along the strike and pillars were formed by raises or slopes and crosscuts. Pillars were recovered to the extent that ground conditions permitted by splitting or taking 'skips' from the sides of the raises or splits or crosscuts. Because of the variety of conditions that existed in the field a considerable range of cutting, loading and support methods were employed, including hand-loading, slushers and scrapers, duckbills and shaker conveyors, mobile loaders and continuous miners. Except for the coal obtained by continuous miners most of the coal was broken out by blasting when driving narrow working places or by air picks when cutting from a face. In the early years hand loading onto cars or conveyors predominated. A continuous miner was introduced into Canmore in 1959 on a trial basis, and another was subsequently acquired, in order to minimize blasting and hand loading, but problems in operating these machines in inclining seams and difficulties in providing safe roof support for the machines and workers restricted their efficient use. Another major difficulty with the use of continuous miners was the problem of ventilating development headings in the very gassy conditions. In the early 1970s they were replaced by electric and compressed air slushers and scrapers, resulting in a general increase in productivity, roof control, safety, and flexibility of operations(1.6,7,8.9)."

Jan 1, 1985