Search Documents

By Erik Q. Dahl

The strength of green and sintered pellets during reduction under various conditions in a laboratory kiln has been investigated. Equipment and test methods are described, together with the results obtained. The strength of sintered pellets drops sharply when the reduction starts, and goes through a minimum at the 70 per cent oxidation level. At more advanced reduction, the strength increases with increasing metallization. Successful use of green pellets as kiln feed requires that more attention be paid to the pellet preparation than is necessary when producing pellets for separate sintering. In particular, the ores have to be ground to a greater fineness. The initial strength of green pellets is low. Below the 70 per cent oxidation level, however, the strength of these pellets is about the same as the strength of sintered ones. Additions of such materials as silica, limestone and anthracite coal; within reasonable limits, affect the strength only slightly.

Jan 1, 1966

By Wm. D. Jr. Sheldon

THIS paper presents practical data to aid in the selection of a mine ventilating fan, and outlines considerations to be made to ensure satisfactory operation and optimum efficiency of the fan. Much has been published on the general subject of mine ventilation, but the writer has found few specific data on factors and considerations which govern the selection of a fan-data which should be available to the operator if his fan is to give satisfactory service within the range of the high-efficiency portion of its performance curve and deliver the specified air capacity when operating against the anticipated range of resistance of the mine. The total quantity of fresh air furnished by the ventilation system must be adequate to provide, and to ensure at all times, safe and healthful working conditions in the mine. It is assumed that the mine operator is able to determine the air quantities required for the various parts of the mine.

Jan 1, 1941

By J. Fellowes, V. Landais, J. Robson, J. Carr

"Aerospace Al-Zn-Mg-Cu (7xxx) alloys are known to be susceptible to environmentally assisted cracking (EAC). This phenomenon has been studied intensively for many decades, leading to empirically adopted methods to mitigate this problem through overaging and composition design. In parallel, many theories have been developed to explain EAC in 7xxx, but none is yet universally accepted. Today, a number of emerging techniques offer potential to shed new light on EAC in 7xxx. The purpose of the present paper is to demonstrate how X-ray tomography (XCT) combined with electron microscopy can be used to identify the true crack path in 3-dimensions, and hence identify material for site specific electron microscopy analysis. Composition mapping over large areas to high accuracy has been performed using a modern electron microprobe analysis system. This has been combined with transmission electron microscopy to investigate local composition in matrix and precipitates at high resolution. This combination of techniques across length scales offers the potential to provide new insights into the links between local composition, microstructure, and EAC resistance.INTRODUCTION Environmentally-assisted cracking (EAC) is a phenomenon which dramatically decreases the performance of metals and can cause premature failure of large structures. Observed in situations where components were not subjected to critical loads and no widespread corrosion was involved, this type of brittle failure is extremely difficult to predict. The EAC designation covers a number of phenomena, e.g. stress corrosion cracking (SCC), hydrogen embrittlement (HE), corrosion fatigue (CF), etc. Initially identified in steels, EAC can also affect other metals such as high-performance aerospace aluminium alloys, and this phenomenon has been a concern for industries for decades. Extensive research has been conducted on the effects of various environments (moist air, saline water, dry hydrogen gas, etc.) on microstructures and crack propagation, however no consensus has been reached and the exact nature of the mechanisms that control EAC is still being debated (Birnbaum & Sofronis, 1994; Gangloff, 2007; Holroyd & Scamans, 2013; Lynch, 2012; Oriani, 1972; Scamans, Alani & Swann, 1976, Young & Scully, 2002)."

Jan 1, 2018

By M. R. Hudec, M. A. Nikolinakou, P. B. Flemings

"We model the shale response to the large deformations associated with salt bodies, and we identify the implications of the stress changes for hydrocarbon exploration. We employ both the static and evolutionary approach, and show that while the static one can model actual geologic geometries, only the evolutionary approach can provide a detailed description of the stress history of shales, which is essential for predicting stress, porosity, and pore pressure and, more generally, for understanding Earth processes related to salt-hydrocarbon systems.INTRODUCTIONDuring the last two decades, understanding the stress, material behavior, and pore pressure in shales around salt bodies has become increasingly important. The energy industry routinely drills near salt (Beltrão, Sombra, Lage, Fagundes Netto, & Henriques, 2009; Meyer, Zarra, Rains, Meltz, & Hall, 2005; Seymour, Rae, Peden, & Ormston, 1993), because a significant number of hydrocarbon reservoirs around the world are found in layers dipping away from salt diapirs.Salt is a viscous material that cannot sustain deviatoric stresses. Under differential loading it flows, changes shape, and eventually relaxes to an isostatic stress state (Urai & Spiers, 2007). Therefore, emplacement of a salt body and its viscous relaxation process may cause significant deformation of the surrounding sediments, perturb their state of stress and create local overpressures (Dusseault, Maury, Sanfilippo, & Santarelli, 2004; Seymour et al., 1993). As a result, drilling near salt is particularly challenging, and problems leading to additional expense or even abandonment are common (Bradley, 1978; Dusseault et al., 2004; Meyer et al., 2005; Seymour et al., 1993; Willson et al., 2003).Historically, salt and the evolution of its cross section to the present day geometry have been studied using kinematic restorations (Rowan & Ratliff, 2012). This approach aims to explain the present geologic section through a sequence of plausible past sections; however, it does not model the constitutive response of the wall rocks, hence it cannot provide any prediction on their state of stress. Similarly, largestrain numerical studies (Albertz & Beaumont, 2010; Chemia, Schmeling, & Koyi, 2009; Goteti, Ings, & Beaumont, 2012; Gradmann, Beaumont, & Albertz, 2009) have focused on the rheological evolution of salt systems without modeling the geomechanical response of the sediments."

Jan 1, 2015

By M. Kreuh

An investigation of the pressure pulse spectrum generated by the gas dispersion processes in a Peirce Smith copper converter was undertaken via the simultaneous measurement of four tuyeres using high frequency pressure transducers. The data was captured, stored, and analyzed using digital data processing techniques; including power spectral density plots, band-pass filtering, and a principal component analysis (PCA). The process was characterized throughout by a dominant 3 Hz pulse signature attributed to the formation of lateral gas envelopes. In particular, test tuyeres in the tuyere line tended to operate synchronously at the dominant frequency, regardless of operating conditions tested and despite being distributed along the converter. Synchronous behavior is thought to arise from the acoustic coupling and possible resonance behavior of the gas delivery system on the converter.

Jan 1, 2007

By T. S. Li, D. Ilievski, I. Livk

Micromixing of the fluid and the particulate phases in a continuous gibbsite precipitator was investigated for three different micromixing states, namely maximum mixedness (MM), complete segregation (CS), and maximum mixedness of the fluid but complete segregation of the particulates (MMF-CSP). The influence of the micromixing on continuous precipitation of gibbsite was studied at different precipitation conditions via simulation. Three different cases were considered with respect to the precipitation kinetics: (1) gibbsite secondary nucleation is favoured with slow crystal growth and agglomeration rates; (2) gibbsite crystal agglomeration and growth are dominant mechanisms with secondary nucleation suppressed; and (3) gibbsite crystal growth is the only relevant phenomenon. Simulation results for the cases (1) and (3) showed that the crystalline products for both the MM and MMF-CSP micromixing states were very similar, but the product obtained from the CS micromixing state was considerably different. This indicates that at those precipitation conditions the fluid micomixing has the dominant effect on the product properties, and the particulates micromixing effect is insignificant. However, when operated under the conditions of fast crystal growth and agglomeration kinetics, i.e. case (2), both the fluid and the particulates micromixing were found to affect the precipitation process, resulting in a significantly different product. Computational Analysis in Hydrometallurgy 35th Annual Hydrometallurgy Meeting held in conjunction with the 44th Annual Conference of Metallurgists ofCIM Calgary, Alberta, Canada Edited by

Jan 1, 2005

By Gaston Giuliani, Jérome Massot, Didier Bourlès, Lionel Siame

"Abstract - We present a new approach for the evaluation of the potential of emerald reserves in gem projects using beryllium (Be) mobility. The distribution of Be in the different phases of hydrothermally altered (albitized) black shale hosting Colombian emerald deposits indicates that Be mobility is associated with the breakdown of Fe-Mn oxyhydroxide phases. The amount of Be that can be mobilized (~0.7 x 10-6 g/g; i.e., 0.7 ppm) may represent up to 18 wt% of the total Be contained in the black shale. A mass balance calculation applied to a well-constrained alteration zone of the Chivor mines, and based on the quantification of Be that can be mobilized under hydrothermal conditions, gives an estimate of the total gem reserves of these mines. Resumé - Une nouvelle approche, basée sur la mobilité du béryllium (Be) pour l’évaluation des réserves d’émeraude dans des projets d’exploitation de gemmes est présentée. La distribution du Be dans les différentes phases minérales de schistes noirs hydrothermalisés (albitisés) qui contiennent les gisements d’émeraude colombiens, indique que le Be mobilisable se trouve dans les oxyhydroxydes de fer et de manganèse. La quantité de Be potentiellement mobilisable (~0,7 x 10-6 g/g; soit 0,7 ppm) constitue jusqu’à 18% poids du Be global contenu dans le schiste noir. Un bilan de masse appliqué à la zone d’altération hydrothermale des mines de Chivor et basé sur la quantification du Be mobilisable, donne une première estimation des réserves à émeraude de ces mines. rieur."

Jan 1, 1999

By A. Dahi Taleghani, Amir Shojaei

A continuum damage mechanics (CDM) based constitutive model has been developed to describe elastic, plastic and damage behavior of rock during drilling. In addition to inelastic deformations, this model incorporates rock anisotropies like toughness anisotropy due to the bedding planes orientation that is a common observation in soft Shales. The pressure sensitive inelastic deformation of porous rocks together with their damage mechanisms are studied for drained and undrained conditions. Fracture mechanics of microcrack and micro-void nucleation and their coalescence are incorporated into the formulation of the CDM models to accurately capture different rock failure modes. The performance of the developed elastoplastic and CDM models are compared with the available single cutter test data of a specific shale play and then the models are introduced into a commercial finite element package through user-defined subroutines. A workflow to derive the required model parameters is presented through inverse modelling of the single cutter test data. The developed CDM model outperforms the traditional discrete element and fracture mechanics approaches by removing stress singularities at the fracture tips and simulation of progressive fractures like formation of the cuttings ribbon without any essential need for remeshing. This model would provide a robust tool for modeling bit performance and rate of penetration using conventional elements of FEA with a reliable results and a computational cost less than similar computational techniques like discrete element methods.

Jan 1, 2015

By Leopoldo Gutierrez, Sergio Castro, Lina M. Uribe, Janusz S. Laskowski

"The effect of sulfite and metabisulfite ions on the amyl xanthate flotation of copper-activated pyrite, in distilled water and seawater, has been studied by micro-flotation tests and redox potential measurements. The activation of pyrite was carried out varying copper ions concentration. It was found that in the presence of copper ions in solution, sulfite and metabisulfite are able to depress copper-activated pyrite at neutral or slightly acid pH. After the addition of sulfite or metabisulfite ions the resulting pH is more acidic with metabisulfite ions. A significant increase of the redox potential of the solution was observed as copper ions concentration increased. Then, the initial reducing conditions brought about by sulfite and metabisulfite ions, change abruptly to oxidizing conditions in the presence of copper ions. Under these oxidizing conditions, the metabisulfite showed to be an effective depressant for pyrite mainly in seawater. However, sulfite was a pyrite depressant in both distilled water and seawater. Based on these results, the pyrite depression by sulfoxy-depressants during the flotation of Cu/Mo ores in distilled water and seawater is discussed.INTRODUCTIONDepression of pyrite by sulfoxy-depressants (sulfite and metabisulfite) in the presence of copper ions is an important issue. This is particularly true when pyrite depression in the flotation of Cu/Mo sulfide ores is carried out in seawater. The use of lime in seawater must be avoided because the formation of magnesium hydroxy-complexes and precipitating magnesium hydroxide strongly depresses molybdenite flotation (Castro et al., 2014). In order to solve this problem, one large plant in Chile uses sodium metabisulfite (MBS) instead of lime to depress pyrite in seawater. In plant practice, this also improves molybdenite flotation since with the use of MBS the pyrite depression is carried out at pH 6-7, instead the pH 11-12 usually employed with lime.From a general point of view, pyrite exhibits some natural floatability over acidic pH ranges and may be partially floated without thiol collectors (a coating of sulfur/polysulfides has been claimed). Therefore, pyrite flotation with xanthates is usually high in the acidic pH region, but decreases greatly at alkaline pH (Leppinen, 1990; Fornasiero and Ralston, 1992; Zhang et al., 1997)."

Jan 1, 2016

The system of keeping geological plans and sections for the Geco Mine at Manitouwadge, Ontario, is described. Special methods employed to save draughting time with-out sacrificing accuracy, such as the extensive use of black line prints, are discussed. The uses made of the plans and sections by the mine planning engineers in their designs of stopes, and by the blast-hole engineer in ~is preparation of blast-hole layouts, are noted. An unusual scheme for portraying the distribution of .copper, zinc and silver values within the ore zone is de-scribed. The method of estimating the grade of ore to be "blasted in each ring of blast holes is outlined, as is the method of estimating the annual ore reserves. The design of an effective but simple transparent geo-logical and mine development model, used as a display for -visitors, is discussed. A large-scale model used for the study of problems in geological structure is also de-scribed.

Jan 1, 1964

By M. Al Mukhtar, D. Hoxha, X. Brunetaud, D. P. Do, C. Auvray, L. Michel

"Mechanical behavior of rock joints is often the key factor governing the response of complex structures constructed in fractured rock masses such as underground openings or of objects assembling various stones blocks such as historical building walls or damaged marble statues. This paper aims at developing a theoretical model to describe the behavior of fresh joints based on the description of their morphology. The main idea of the model is to establish a link between the effective contact surface of joints and the frictional coefficient. Beginning from a chosen level of joint surface description where a joint is considered as “smooth”, the model describes the added friction with respect to the increase of the contact surface of the joints and the distribution of stress in these contacts. The model developed initially for asperities with regular geometry is firstly compared with existing models and then applied on fresh artificial joints. For that, healthy artificial joints have been characterised using in one hand classical CNL shearing tests and in another hand the morphology of joints. The joints surfaces are digitized before testing using a high resolution laser scanner (Konica Minelota Vivid 910) allowing to obtain a precision up to 10µm. From these scanned surfaces the morphology of joints is characterised on the profiles running in the direction of shearing and a mean value of friction is calculated using the developed model. This calculated value is then compared with that obtained from CNL shearing test and a good approximation is notedINTRODUCTIONThe role of the mechanical behavior of rock joints on the overall response of fractured rock masses is well established in many fields of engineering activity going from the stability of underground constructions (Souley M, Hoxha D, Homand F 1999), rock slope stability (Einstein H.H. Veneziano D., Baecher GB., O’Reilly K.J, 1983, Jaeger 1971), various rehabilitation of masonry construction, damaged stone artworks restoration (Michel L., Do D.P, Coignard B, Hoxha, 2014) and so on. In the same time the characterisation of the behavior of joints and their modeling is nowadays a dynamic field of research or/and investigations and many alternative approaches have been proposed (Barton, N.R. and Choubey, V. 1977, Tatone, S.A. Bryan, Grasselli Giovanni 2010, William C E. 2007). While empirical relations of shear strength with various parameters of the joint morphology are the most used in practice because of their simplicity (Barton. and Choubey, 1977, Barton 1973, Bandis S., Lumsden A. C. and Barton N. R. 1983) many other models of joint strength are developed based on mechanistic considerations (Haberfield CM, Johnston IW. 1994), multiscale approaches (Yang Z.Y., Di C.C., Yen K.C. 2001, Fardin N., O. Stephansson, Lanru Jing 2001) or micromechanical ones (A. Serrano, C. Olalla, R.A. Galindo 2014) to mention just a few of research trends on rock joints modeling."

Jan 1, 2015

By S. Shairp

The first commercial application of the Dynatec two-stage zinc pressure leach process commenced operation at the metallurgical complex of Hudson Bay Mining and Smelting Co., Limited in Flin Flon, Manitoba in 1993. A key feature of the successful leaching operation is the presence of iron in solution, which facilitates oxygen transfer in the autoclaves and enables rapid oxidation of zinc sulphide minerals. At the same time, the solution from which zinc is recovered must be essentially iron free. Precipitation of iron from the solution starts in the autoclaves and is completed in subsequent atmospheric purification steps. Conveniently, these iron precipitation steps also remove nuisance elements such as arsenic and fluoride from the solution, while producing solids with good liquid-solid separation characteristics. This paper provides an overview of the current operations in Flin Flon, with particular reference to the behaviour and deportment of iron throughout the zinc plant.

Jan 1, 2006

The dynamic breakage process of rocks by the impact of a hydraulic hammer is more complex than one normally assumes. It is even more difficult when one has to conduct the breakage under water. In such cases one does not know exactly what the surface topography and composition are at the bottom of the sea or river and, hence, it is more difficult to select the best position of the hammer before starting the hammering. Typically, an industrial hammer has a diameter of about 250 mm, a length of about 1.25 to 1.75 m and a mass of several tons. The hammer frequency can be up to 50 impacts per minute. The general principles of rock hammering can be easily summarized, but this knowledge is not sufficient to adapt adequately the method for less common rock conditions (e.g. less brittle rock, presence of vertical and subvertical fractures, etc.). That is the reason why we initiated a research project, whereby a scale model has been developed to conduct experiments in the laboratory and whereby discrete element simulations are being conducted. Both aim at a better understanding of the basic mechanisms of rock hammering. The scaled experimental model allows varying the impact energy and the static weight independently. Within the experiment, the hammer is in contact with the rock specimen under a certain confining pressure and with a certain contact pressure due to the static weight. A weight falls on the hammer, creating the dynamic action or impact; the height over which the weight falls can be varied. The penetration is recorded after each impact. After a certain penetration the test is stopped and the internal crack patterns are described. Some simulations have been conducted, allowing the modeling of individual fracture initiation and growth during the penetration of the hammer by either a constant displacement rate (using the UDEC-code) or by introducing the dynamic process (using the PFC-code). Some of the observed features in the laboratory experiments can be visualized in the simulations. However, further research is needed to allow the simulations being an adequate tool to well understand the dynamic process in laboratory experiments, as well as the in-situ behavior.

Aug 1, 2013

By Eric Poulin, Anthony Clapperton, Jocelyn Bouchard, Jaime Cristobal Rojas-Montes, Benjamin Legare

"Several grinding mill dynamic simulators have been developed in the last half-century. However, complete circuit simulations are mainly limited to academic investigations, and on-site applications for advanced control or real-time optimization are scarce. One particular issue that has certainly curbed a more widespread use is the time and efforts required for model calibration. This paper illustrates this challenge and presents a calibration method based on dynamic simulation using industrial data and laboratory testwork. The simulator models discussed originate from the work of Austin and Luckie (1972) for grinding mills, and Plitt (1976) for hydrocyclones. A two-stage approach based on a least squares minimization allows determining calibration parameters values. Firstly, laboratory testwork are required for characterizing breakage coefficients of the ore. Secondly, step change responses and their simulation— effect of ore and water feed rates on output flow rates and size distributions—allows identifying transport/mixing conditions. Simulation results are in agreement with actual process responses to variations of feed conditions obtained from a plant survey.INTRODUCTIONDynamic models for grinding circuits has been intensively studied since the 1970's notably by Austin and Luckie (1972b), Klimpel and Austin (1984), Rogovin and Hogg (1988), Napier-Munn et al. (1996), Liu and Spencer (2004), and King (2012) among others. The resulting models primarily serve in simulation applications for process equipment sizing, which incidentally also helps developing a better understanding of comminution operations. An obstacle curbing a more widespread and targeted use of grinding simulation for process control and optimization purposes is the time and efforts required for dynamic model calibration. It remains a cumbersome task that is typically not well detailed in technical papers. This could explain why dynamic process simulators are mainly confined to academic applications."

Jan 1, 2016

By Akihiko Nishiyama

Unmanned construction technology used for remote control operation of construction machines has some problems to solve compared with manned operation of construction machines, such as fatigue due to long-term operation or decreases in operational efficiency. To solve these problems, we recorded the viewpoints of operators in both manned and remote control operation and analyzed the differences. This paper reports on our discussion of improving the operability of remote control operation based on the analysis results.

Aug 1, 2013

By E. P. Wiechrnann, C. M. Castro, G. A. Vidal

In copper Eta plants the optimal current density setpoint depends on the electrolyte composition and temperature. However, conventional plants operate with large standard deviations. A value of 14% with current densities offsets up to ±50% is typical. For worst, during opencircuit or shortcircuit events this variation can be from -100% to +200%. Naturally, energy consumption and copper quality are compromised. Several devices have been successfully employed to reduce set point deviations. Last developments include; Optibar Segmented Intercell Bars, Outotec Electrodes Arranging Method and NTC Selective Electrodeposition Enhancers. This paper researches and compares these technologies. It is shown that short circuits can be effectively reduced in occurrence and magnitude. Moreover, 95% of the electrodes can be forced to operate within ±10% of the set point. The specific energy consumption is reduced from 2,000 KW per Ton to values close to 1,900 KW per Ton.

Jan 1, 2011

By D. Kong, A. Klyashtorin, L. McGilp, I. Wilson

This work reports on applying iron oxide coated sands media in an experimental permeable reactive barrier to remove uranium species from uranium containing water. A field experiment was conducted at the legacy Gunnar uranium mine & mill site that was abandoned in the 1960s with limited to no decommissioning. The flooded Gunnar mine pit presently contains about 3.2 million m3 of water contaminated by dissolved U (1.2 mg/l), Ra-226 (0.4 Bq/l), and minor concentrations of other contaminants (As, Se, etc.). The water is seeping over the pit rim into Lake Athabasca posing environmental and health concerns. Iron oxide coated sands can be used to immobilize uranium species through an adsorption process. Methods for preparation of hydrous ferric oxide sorbents and their supported forms onto silica sands are described. Fourier transform infrared spectroscopy (FTIR), and powder X-ray diffraction (pXRD) were used to characterize the physical-chemical properties of the sorbent. The monolayer uranium uptake capacity (Qm) was estimated through the Langmuir adsorption isotherm. Adsorption kinetic experiments were performed in a lab environment before moving to a field trial. Based on these lab results and the input on field-scale appropriate geometries, a pilot permeable reactive barrier was fabricated and a field test conducted near the Gunnar pit in June 2019. This pilot test provided technical data and information needed for designing a full-scale permeable barrier based on the iron oxide coated sands, which may be applied for in-situ water treatment at Gunnar and other legacy uranium sites.

Jan 1, 2020

By Kazutoshi Haga, Batnasan Altansukh, Yasushi Takasaki, Mohd Yazid Bin Abdul Razak, Atsushi Shibayama

"In this study, the volatilization behaviour of arsenic (As) and antimony (Sb) from arsenicantimony bearing minerals such as tennantite (Cu12As4S13)/tetrahedrite (Cu12Sb4S13) in copper ore was investigated using a roasting process. Specifically, the thermal decomposition of tennantite and the arsenic volatilization were investigated under nitrogen and air atmosphere. The roasting experiments were performed at temperatures ranging from 500 to 1,200oC and different retention times using a laboratory electric furnace. The results indicated that over 95% volatilization was achieved at 700oC. On the other hand, when the temperature increased to 1,200oC, volatilization rate of Sb reached to 90%. Therefore, volatilization of Sb requires high temperature compared to As. It suggests that As and Sb can be separated using temperature difference. Selective removal of As is possible at 700oC, subsequently Sb can be recovered as a volatilized product by increasing the temperature to 1,200oC. Meanwhile, volatilization of Cu and Fe was not observed on these conditions. The content of As and Sb in the residues obtained from roasting at 700 and 1,200oC was less than 0.3 and 0.75 mass%, respectively. The Cu content in solid residue at 1,200oC increased to 34 mass%. The clean copper concentrate with lower amounts of arsenic and antimony was obtained from the process. INTRODUCTIONRecently, arsenic (As) and antimony (Sb) contents in copper (Cu) concentrates are increasing year by year. Arsenic and antimony are present with Cu minerals such as enargite (Cu3AsS4), tennantite (Cu12As4S13) and tetrahedrite (Cu12Sb4S13) that associate with copper sulfides [chalcopyrite (CuFeS2) and bornite (Cu5FeS4)]. They are normally concentrated by flotation and treated in copper smelters. However, treatment of copper concentrates containing high amounts of arsenic and antimony by a smelting process is difficult due to environmental implications of toxic arsenic and antimony. As demand for copper continues to grow, the need to source copper from several types of resources including those that contain high levels of As/Sb becomes necessary. Therefore, a novel processes for the treatment of As/Sb bearing Cu concentrates are required. Reviews on copper resources such as enargite, tennantite and tetrahedrite containing high amounts of arsenic and antimony are covered widely in literatures by many researchers (Padilla et al., 1998; Welham, 2001; Vinals et al., 2003; Guo & Yen, 2005; Balaž & Achimovicova, 2006a; Filippou et al., 2007; Mihajlovic et al., 2007; Lattanzi et al., 2008)."

Jan 1, 2016

By I. Filippova, L. Filippov

"The by-product potential of light rare-earth elements (LREE, La, Ce, Nd) and rare-metals (W, Nb, Sn) within the St Austell kaolin deposits (UK) is related to the kaolinisation process, which liberates the accessory heavy minerals of the host granite in the clay matrix and allows their separation in the waste streams. As a consequence these minerals are pre-concentrated in the micaceous residue which displays relatively high LREE content (around 170 ppm) hosted by monazite which is mainly distributed (up to 95%) in the -100 µm fraction. A combined gravity/flotation concentration flowsheet, starting with classification of the residue into 3 size fractions (+150 µm, 150-53 µm and -53µm) was developed. This study presents the results of the clay-rich -53 µm size fraction beneficiation by flotation using sodium oleate and hydroxamate as collectors.The effect of dispersant addition during de-sliming operations on flotation efficiency was also investigated. The LREE grade in the floated product obtained with sodium oleate increased from 3370 ppm to 5350 ppm and recovery from 30% to 80% with dispersant which is attributed to clay coating. Comparison of flotation performance and Falcon Ultra-Fine (UF) concentration of monazite to previous results obtained with Falcon Semi-Batch (SB) gravity concentrator on the unscreened raw residue clearly shows that flotation of the fine residue is more efficient than Falcon UF and Falcon SB. Indeed Falcon UF produced high recoveries (87-95%) but with almost no enrichment (1.3-1.4 ratios) whereas Falcon SB concentration of unscreened residue produced higher grades (up to 0.6 % LREE) but with low recoveries (17-22 %). These preliminary results show that LREE can be pre-concentrated suggesting that the micaceous residue stream (and the associated tailings dams) could be considered as a potential resource for these metals."

Jan 1, 2016

By T. Krumins, L. Zunti, R. Frischmuth

Mercury is known to occur in sulphide-bearing refractory gold deposits in the form of sulphide minerals or elemental inclusions. These deposits typically require an oxidative pre-treatment process, such as pressure oxidation or roasting, to achieve economic gold recovery. However, these processes also have the potential to liberate mercury, a portion of which may then be released to the environment through gaseous emissions. Mercury emissions from mine processing operations have been of particular interest in recent years, as governments impose lower emission targets and organizations adopt better industry practices to reduce the environmental and health aspects of releasing mercury into the environment. This paper describes various mercury removal technologies with respect to pressure oxidation gas handling circuits, with a focus on key design variables and technology selection criteria.

Jan 1, 2014