Search Documents

By Laura Prati

Gold-on-carbon catalysts resulted very active and selective in liquid phase oxidation [1, 2, 3] and during past studies we established that activity is ruled by two factors: particle dimension and gold exposure on the carbon surface [4]. These two parameters are also connected to the nature of activated carbon where the chemical nature of the surface oxygenated groups probably plays an important role [5]. Our studies, focused on the design of an active gold-on-carbon catalyst for liquid phase application, were aimed, operating a fine tuning of all the parameters involved in determining activity, to optimize gold-on-carbon preparation, keeping in mind that gold particle activity increases with decreasing particle size and increasing gold exposure. Gold sol immobilisation represents a versatile methodology in preparing gold catalysts [6]: throughout this work we used as sol stabilizing agent, the N-dodecil-N,N-dimethyl-3-amino-1-propan sulphonate (SB), that provides both sterical and electrostatic stabilisation, a condition we already demonstrated necessary to preserve particle dimension when carbon is used as the support [6]. We generated different gold sols by varying the relative amount of reagents (HAuCl4, SB, NaBH4), the type of alkali and the temperature of the gold precursor reduction. Moreover, as we had recently evidenced that there is also a carbon effect [5], we employed only one active carbon to immobilize the sols.

Oct 1, 2003

By T. R. Roy

"This paper presents an objective model for the estimation of fire risk potential of an underground coal mine panel by the bord-and-pillar method of mining where extraction is carried out by depillaring with caving. The fire risk rating procedure for the estimation of fire risk potential involved in the panel is described in detail. The model developed thereof is tested with the field data collected from different collieries across the country along with the laboratory data for critical assessment of fitness of the model. Some results showing the validity of the model are also cited here. Introduction The occurrence of fire in underground coal mine panels is quite common in India and elsewhere. These fires cause extensive loss of resources.Although substantial work has already been done by different research organizations, the problem has not been fully eliminated.The causes of panel fires depend not only on the spontaneous heating susceptibility of coal, but also on the extraneous conditions created in the panel due to the mining operations. From the studies done so far by various organizations, it is apparent that two types of parameters associated with spontaneous heating of a coal mine panel exist: intrinsic and extrinsic. Parameters related to the nature of coal, i.e., its physicochemical characteristics, petrographic distribution and mineral make-up are intrinsic, while the extrinsic parameters are related to the atmospheric, geological and mining conditions such as scope of leakage of air into the panel, wetness of mines, heat dissipation capacity of the panel, gassiness of seam, geological disturbances, method of extraction, size of panel, etc.Banerjee (1982) identified twenty-two mine parameters such as spontaneous heating susceptibility of coal, method of mining, geological disturbances, quality of overburden, degree of consolidation of coal mass, scope of accumulation of coal fines, etc. that can influence spontaneous heating in underground mines. He used the terms “high” and “low” for fire risk rating of each of these parameters. Since this approach is oversimplified, it can not determine the exact fire risk potential of an underground working."

Jan 1, 2003

By W. T. Martson

ABSTRACT Sooner or later, every producing mine faces the question of fill. This paper invites consideration of mill tailings as an economical, efficient, and quantitatively adequate source of such fill. Some of the advantages, disadvantages, methods of utilization, and methods of treating mill tailings for sand recovery are covered. ADVANTAGES AND DISADVANTAGES OF SAND FILL DISREGARDING economic com-promise, that material which supports the greatest applied load with the least compression is the best choice for fill. Table I, reproduced from U. S. Bureau of Mines Bulletin 60, is offered as evidence of the adequacy of hydraulically placed sand. Table II gives the results of tests made in an effort to determine the reason for the difference between load hearing qualities of dry-placed and hydraulically-placed sand. From these, it would appear that hydraulic placing gives a denser initial packing, with corresponding higher, and faster development of, load bearing qualities. Assuming this to be true, then if sand from mill tailings can be placed underground economically, it is the superior fill material. Table III summarizes cost data available. The most cursory glance through the available references (2, 5, 6, 7, 8, 9) will show .that the major benefit from the adoption of sand fill is a decrease in the non-productive fill ?cycle of a working place. This, it is estimated, increases the output of an individual stope by from 25 to 50 per cent. The advantage of reducing the number of required working places for a constant daily production is obvious.

Jan 1, 1951

By Tao Long

Recently, the great amount of funds has been invested in the reconstruction of damaged infrastructure and house of subsidence area of coal mine and mine reclamation. This is a benevolent and popular work, which is highly praised. However, because of complicated collapse area problems in China, especially the less integrated control research in the collapse area of metal mine, and the technological weakness, how to effectively control the subsidence area, restore landscape and ecological environment, and utilize the abandoned mine land, are major issue related to the mining area of sustainable development. The research situation about the formation of metal mine collapse area at home and abroad is reviewed, and then the effect of the collapse area on the mine safety and ecological environment, the existing technical problems and development direction are analyzed. Lastly, the technical measures of the collapse area control and cooperative underground mining is put forward.

Oct 1, 2010

By Anthony T. Eyton

Intelligent Systems: Advantages for Mining ? Increased safety (reduced risk to workers) ? Increased productivity (reduced downtime) ? Reduced maintenance costs ? Customized solutions for different mines ? Growing acceptance among mine managers A Typical Precarn Project ? Meets definition of intelligent systems ? Involves at least two Precarn members ? a technology developer partner and a user partner ? in a true collaboration ? Involves at least one university and may have various other players ? Leads to a demonstrated prototype ? Costs $2-4 million, and lasts 12-30 months ? Gets up to 40% of its funding from Precarn (max. $1 m) ? Produces new intellectual property -- owned by the project team

May 1, 2002

By J. H. Nantel

Indications are that underground mining is gaining favour with large and small mining companies due to environmental and sustainability concerns. Dramatic changes to mine fill technologies will be needed in order to keep pace with these emerging trends. The industry will be compelled to gravitate toward zero discharge mining operations. Innovative handling of mine tailings will become a focal point in this effort. The challenges are to use a greater portion of the residues and to manufacture a fill with better properties. This is a tall order that can only be addressed through a systematic research and implementation process involving mining companies, universities, research organizations, manufacturers and governments. The mining industry has to be at the forefront of this technology push in mine fills for the future mines. It will also be called upon to lead the way in other research areas. The industry will have to partner with other technology providers: universities, government laboratories and consultants.

May 1, 2007

By Maureen E. Lipkewich

Education builds long term awareness, acceptance and support for responsible mineral resource development. The MABC Education Program is an award winning education partnership with British Columbia classroom teachers that has helped over 5400 teachers with resources and other learning opportunities. Each year, thousands of students begin, and continue, to learn about our modern mineral industry as a result of this teacher-written program. The CIM network has an integral role in the future of mineral education in today?s classrooms in Canada and programs of this caliber are vital to our future. The industry needs help in raising awareness of the benefits of modern mining and teachers need help in acquiring that information.

May 1, 2002

By Mohsen Amir-Rahmat

The ore of Sarcheshmeh copper deposit that has been located in the south ?east of Iran, contains four type of rock that they have their specific hardness and strength according to their alteration type and mineralization. Blasting of these various types of mine rocks prepares various types of size for the product of mine as the feed of concentration. Along the crushing of this feed a few factors effect on the efficiency of the crushing unit. The aim of this project has been the consideration of the effect of ore size on the efficiency of crushing unit. For this investigation along the year 2000 A.D., six sample from feed and six sample from product of crushing unit have been prepared. The results of the screen analyze of these samples has shown that the size of feed has been lesser than the primary plan and the size rate of the product has been bigger than the primary plan. Also in this research the effect of feed size on the quality of product size has been considered.

May 1, 2003

By Floyd B. Bowen

Pumping methods are used, almost exclusively, to transport materials in the mining, beneficiation and chemical processing of phosphate rock in the Florida phosphate pebble field. Matrix pumping systems capable of pumping 15,000 g.p.m., transporting 15,000 long tons (dry) per hour, are now in use. They utilize 16-by 48 Yz -in. pumps, driven by 1.250-h.p. motors, discharging into pipelines 20 inches .in diameter .and sometimes several miles in length. As an average, it is necessary to pump 3 tons of matrix to the beneficiation plants, and to dispose of 2 tons of sand tailings and clay as waste, in order to produce 1 ton of shipping-grade rock. The washers and flotation plants, where the clay and phosphate and silica particles are separated, require the movement of large volumes of slurries with densities ranging from 2-3 per cent to 45 per cent solids, by weight. Extensive waste disposal systems require the pumping of dilute clay slurries in quantities of up to 50,000 g.p.m.,

Jan 1, 1963

By F. F. Roberto, E. Kirby, A. R. Marchbank

The application of biologically assisted methods for metal extraction in the mining industry has a long history, but development of modern techniques has been relatively slow. There is, however, a resurgence of interest in the industry with the recent development of methods to successfully treat base metals concentrates. Two major pilot plant programs for treatment of chalcopyrite concentrates have been initiated in the past year and results from one are beginning to be released. This paper provides an overview of methods that have been applied in the past, from the earliest deliberate applications of the technology, through the copper and uranium heap and dump leach applications, the more highly engineered agitated tank leach gold applications and the developments currently taking place in the industry.

Jan 1, 2003

By Oyku Selimoglu

The key to successful mine production plan and subsequent operation is efficient mine layout design and optimization. Pit layout design and optimization allow the delineation and extraction of mineable reserves and the minimum waste subject to slope stability, economic, quality and quantity constraints. Many design and optimization software packages have been developed to aid this intensive and challenging process. These packages include VULCAN, SURPAC, DATAMINE, GEMCOM, MICROLYNX, MEDSYSTEM and MINESIGHT. These software packages are developed as integrated computer-aided systems used for database creation, survey, geological and geostatistical modeling, mine planning and production optimization and environmental modeling. In Turkey, many mining companies still plan and design mine layouts with traditional hand methods. In this study, VULCAN has been used to design and optimize the Eti-Bor A.S. Kestelek Boran Open Pit Mine in Western Turkey. The main objective is to show the company the superior advantages of mine planning software for designing and optimizing mine layouts over the traditional hand methods. Drill hole data used by the company to estimate the reserves for planning are used in this study. The ore grade varies between %1,04 B2O3 to %47,33 B2O3. The pit toe and crest strings are projected using variable batter angles and berm distances. On the north side, batter angle is 180 and berm distance is 25 meters, on the south side, batter angle is 320 and berm distance is 15 meters. In addition to that open pit bench height is 10 meter. The concepts of block modeling are applied to the Kestelek open pit mine with detailed ore grade modeling for each block. The Lerchs-Grossmann?s algorithm is used to optimize this mine based on the block model, the economic block values for each block and the underlying field constraints. The results from VULCAN were similar to the estimates by hand. The reserve estimates from VULCAN is 13,192,870 tons compared with the hand estimate of 13,200,000 tons, overburden estimates of 15,622,889 m3 compared with 15,000,000m3 obtained by hand with a stripping ratio 1.18:1 (m3:ton) from VULCAN versus 1.14:1 (m3:ton) from hand estimate. Vulcan improves the efficiency, speed and reproducibility of the planning results. It provides mining engineers, geologists and surveyors with a cost-effective modular system for assessing and planning the mine layouts. Furthermore, Vulcan?s specific modules allow efficient access and manipulation of databases, open pit mine design, block models, optimized 3D mine layouts, and more. However, for competitive business in Eastern Europe, VULCAN should improve its software support. Effective training, help desk support systems and nearby distributors with just-in-time solutions to company problems will generate competitive business for VULCAN.

May 1, 2007

By A. D. Mufch, G. P. Mitchell

"THE HARDY MINE of Falconbridge Nickel Mines Limited is located in Lot 9, Concession 1, Levack Township, Sudbury District, Ontario, 20 miles northwest of the city of Sudbury, and a mile west of the town of Levack. The ore deposit is one of the many nickel-copper sulphide bodies found on, or near, the lower contact of the well-known Sudbury norite-micropegmatite irruptive, and is one of a family of ore deposits which occur on the northwest rim of the irruptive.The property was acquired by purchase in 1935. In the same year a magnetometer survey along the footwall contact of the norite, which is covered by about 150 feet of glacial sands and clays, first indicated the location of the orebody. Drilling from 1935 to 1942 outlined the extent of the ore. Shaft sinking was commenced in the fall of 1951, and the mine is now approaching full production at a rate of about 300,000 tons per year.There are several major differences between the geology of the Levack area and the Falcon bridge area, which lies at the opposite extremity of the irruptive, 28 miles to the east. The purpose of this paper is to describe the essential features of the geology of the Levack area as seen in the Hardy mine, and to supplement the recent papers on other properties in the Sudbury area by Davidson (1), Lochhead (2), and Yates (3).General GeologyA recent review of the regional geology and an extensive bibliography of the Sudbury area can be found in the two papers by H. C. Cooke (4, 5). Some of the recent related references are: Jas. E. Thomson (6), E. M. Abraham (7), Franc. R. Joubin (8), W. G. Q. Johnstone (9)."

Jan 1, 1949

By Philippe Poirier

Les parcs à résidus miniers représentent un risque environnemental qui nécessite une gestion adéquate. Suite à la publication du « Guide sur la gestion des parcs à résidus miniers » en septembre 1998, les membres de l?industrie minière ont appliqué les éléments de gestion du Guide, permettant ainsi une amélioration continue des opérations. En février 2000, l?industrie minière a indiqué le besoin d?établir des lignes directives plus spécifiques pour l?opération sécuritaire des parcs à résidus. Dans cette optique, l?Association Minière Canadienne a publié, en septembre 2002, un Guide pour l?exploitation, l?entretien et la surveillance (EES) des parcs à résidus miniers. Suite au développement du Guide et à son application sur plusieurs sites miniers, il apparaît que la mise en oeuvre d?un Manuel ESS des parcs à résidus miniers permet : ? d?établir les responsabilités des intervenants; ? de s?assurer que les critères d?opération sont appliqués; ? de mettre en oeuvre le plan de déposition des résidus et de gestion de l?eau; ? de rencontrer les normes et exigences environnementales; ? de définir un programme d?entretien et de surveillance des ouvrages; ? d?identifier les risques et de mettre en oeuvre un plan d?intervention d?urgence; de démontrer une opération diligente.

Nov 1, 2002

By Helge B. Wurst, Michael P. Cipold, Jan F. Bachmann, Claus C. Bachmann

"In washability, the objective is to establish the set of maximum possible separation performance criteria for a given mineral feed. The method of choice for this has been the conventional sink-float analysis. Time, cost and safety aspects of the sink-float method have prompted the search for a new approach for establishing separation performance criteria, especially as performance levels of separator plants can be maximized if reliable information based on an analysis of washability in conjunction with particle size distribution, elemental constituency becomes readily available. The new method to establish washability and associated performance information utilizes at least two measurement technologies concurrently: single energy x-ray transmission and image processing. For porous or very inhomogeneous materials the results can be refined further by using dual energy x-ray transmission and image processing. The value of the collected data increases considerably if the washability data were additionally available in time to be considered in the control of the process plant. The incorporation of an automated washability monitor gives near real-time data that would impinge positively on the profitability of the plant operation. The method was extensively tested with a range of sample with different densities, varying from 1 g/cm³ (coal) to 5 g/cm³ (iron ore).INTRODUCTIONWashability of minerals like coal and iron ore is expressed by a curve or graph showing the results of a series of float-and-sink tests. Several of these curves are drawn to illustrate different conditions or variables, usually on the same axes, thus presenting the information on one sheet of paper. Washability curves are essential not only for the design but also for the operation of preparation plants.In determining the washability analysis, particle density is the underlying feature of all washability curves. Conventionally, the particles are separated into density fractions by immersing them in fluids of a predetermined density followed by skimming of those particles that stay afloat. The particles remaining afloat thus have a density lower than that of the fluid they were subjected to. The particles that remained at the bottom of the fluid container thus had a higher density higher than that of the fluid. By progressively increasing, for example, the density of the fluid and immersing the remaining particles so as to be able to skim the next density fraction, the particles would be fractionated into density groups. The liquids used range from aqueous solutions to organic liquids to suspensions. Unfortunately the liquids used for this separation process are often toxic and expensive. It stands to reason that a new method of determining washability is sought."

Jan 1, 2016

By N. Bédard

"This paper highlights Cambior’s initial approach for recruiting and retaining its international employees, the importance of proper preparation and the support needed to ensure a competent and stable workforce.In general, most of the training and information available for human resources personnel prepares the specialist for handling various aspects of labour relations, recruitment and hiring, benefits administration, employee relocation, etc. This is usually done in a Canadian context.Only recently, has more specialized training been developed to prepare human resources practitioners for the complex issues related to expatriate employees and dealing with human resources issues in other countries"

Jan 1, 2004

By J. J. Jonas, G. R. Stewart, N. Pokutylowicz, S. Yue, R. Varano, A. Elwazri

Differing thermal histories in and around a weld can lead to differences in grain size, phase composition and morphology of precipitates; mechanical properties will vary accordingly. Hardness testing gives limited information and the machining and testing of tensile and/or impact specimens that would reveal these variations (which may occur over very small distances) is not practical. Therefore, in this investigation, shear punch testing was applied to measure the variation in the room temperature mechanical properties of a welded pipeline steel.

Jan 1, 2005

By John G. Kelly

"In 1982 an extensive study was carried out to determine the best means of size reduction for the ore to be hoisted through the borehole hoisting system at Sherritt Gordon's Fox Mine.The study examined three alternatives:1. a jaw crusher,2. pneumatic rockbreaker(s) at a grizzly, and3. hydraulic rockbreaker(s) at a grizzly.The final decision was a compromise between alternatives 2 and 3. Two rockbreakers, one pneumatic and one hydraulic, were installed over a single grizzly. Some modifications have been made to the system, but over-all it has operated at acceptable levels since its installation in July 1983.As all the ore passes through a jaw crusher before being hoisted to surface, an evaluation of the relative performance and cost-effectiveness of the jaw crusher and the two types of rockbreakers is possible. This paper outlines the initial study, and compares the three breaking systems in operation at Fox Mine.IntroductionThe Fox Mine of Sherritt Gordon Mines Ltd. is located 800 kilometres north of Winnipeg near Lynn Lake in Northern Manitoba. Production at the copper-zinc orebody began in 1970 at a rate of 3,000 tons per day. Over 12.5 million tons will have been hoisted from the underground mine when the ore reserves are depleted in October 1985.The mining method at Fox Mine is sub-level open stoping with delayed backfilling are from the upper level stopes, above the 2000 level, is mucked on the main levels established at 400-ft elevation intervals, and is fed through a central orepass to the crusher located on 2100 level. Production in the lower levels commenced in 1975, and ore from the 2200 and 2400 level stopes was hauled up a 15010 ramp by 26-ton trucks to the 2000 level orepass dump. Projected production rates from the 2600 and 2800 levels using the trucking system were too low, and therefore, in 1983 a borehole hoisting system was commissioned to hoist that ore'!'. One thousand tons per day of ore are skipped through an 8-ft diameter borehole from the 2650 level loading pocket and dumped on the 2000 level. The ore is transferred by LHD to the main orepass for crushing before being conveyed to the main shaft for hoisting to surface (Fig. 1)."

Jan 1, 1986

By C. J. Brown

Since its commercialization thirty years ago, the Recoflo® short bed ion exchange process has been extensively utilized for the recovery of a wide variety of acids and metal salts. In addition to a reduction in resin bed height from 200 cm to 300 cm to 15 cm to 60 cm, the process has a number of features such as utilization of fine mesh resins in a compressed bed which together make it ideal for a number of applications. The process has been extensively exploited, for example, in the metal finishing industry for recovery of valuable chemicals from electroplating, anodizing, etching and pickling wastes. More recently, it has also been applied in the primary metals industry for purification of copper electrolytes and metals recovery from leachates. The paper discusses several of these applications and some of the issues that were found to be key to their success.

Jan 1, 2004

By Michael W. Russnak

Productivity and operating expenses are everything when it comes to judging how well your mine and company are doing. Stakeholders are always looking at these numbers and trying to understand if productivity is improving, if operating costs are trending downward and what you are basing your decisions on. o make improvements you first need to understand how you are performing. If you can?t get this basic information, you will never improve. You will not be able to make simple decisions related to maintenance, operations or production. Forget about planning, as you will only be guessing based on the numbers some stakeholder or your executive wants to see. The problem miners run into is not that the data doesn?t exist; it does, but typically it?s raw, it?s everywhere and its volume is huge. Today there is more on-board computing capability in shovels than we had on our desktops three years ago. Add other mobile equipment, plant systems and multiple OEM vendors to the equation and the challenge is daunting.

May 1, 2007

By B. Arlyuk

The complex system has been developed for long-term assessment of world prices and sale volume of primary aluminium when using the analytical model of the market and market supply forecasts as well as economy development in the Western countries characterized by the industrial production indices as correct data of Western World aluminium consumption are absent, The important part of this system is the model developed for forecasting the degree of capacities utilization of smelters and refineries depending on the price level, The model contains a statistic part corresponding to the capacities distribution by the production cost, and a dynamic part determining the deviation from the static depending on the price variation dynamics, The developed complex system has been identified by the actual data of the world prices of smelter grade alumina and primary aluminium, conservation and reactivation of refineries and smelters in the Western countries within the period from 1992 to 2003. The system was used for primary aluminium and alumina price forecasts till 2020.

Jan 1, 2004