Search Documents

By Sandvik

Fine grinding in an air-swept ball mill working in closed circuit with a forced vortex air classifier has been investigated first in continuous laboratory and then in industrial scale. Results from the laboratory circuit have shown significant influence of mill load (powder filling) on the capacity of the circuit. In laboratory scale the mill load was measured and controlled by a weighing platform placed under the complete mill set-up. The mill load of the industrial air-swept ball mill has till now been controlled by measuring the power consumption of the mill motor. Thus, it was necessary to operate far from the range of optimal mill filling. To improve the circuit performance, alternative ways of mill load measurement were investigated. An important factor was investment cost, as many fine grinding mills operate in relatively small circuits that do not wan-ant large investment. In this case the task was accomplished by using a piezoelectric strain transducer, which detected strain changes in the mill shell. It was installed in the midpoint of the shell, where the highest deformation was obtained. As the transducer was on the top position, it indicated compression, and on the bottom position it measured tension. By taking the difference between the readings, it was possible to calculate total strain variations, directly proportional to the mill load. The signal from the transducer was sent to a control room via a cordless infrared communication system, employing a microprocessor control card, which could further regulate other operating parameters of the circuit according to the software model. The installation required very low investment cost and provided simplicity of application as well as stability and reliability of characteristics under severe industrial condition. The measurement system made it possible to optimise the mill load and thus increase the production from 3.2 to 3.7 dh (15 per cent), and stabilise the circuit operation.

Jan 1, 1995

Adsorption Behaviours of Humic Substances onto Iron Ore Particle Surface Humic substances extracted from lignite mainly consist of fulvic acids (FA) and humic acids (HA), which have been successfully used as good composite binders for iron ore pellets in laboratory tests and industrial production. However, there exists a general lack of understanding of the interaction between humic substances and iron ore particles surfaces. In this research, by means of zeta potential measurements, Fourier Transform Infrared (FTIR) spectrum, colorimetric method and Environmental Scanning Electron Micrograph (ESEM) imaging, the adsorption behaviours of FA and HA onto the surfaces of iron ore particles are investigated. The zeta potential results indicate that adsorption of FA on the iron ore particles can be characterised by specific and electrostatic interactions, while adsorption of HA is by electrostatic and chemical adsorption interactions. FTIR spectrum results show that adsorption force of FA on the iron ore particle surfaces is stronger than that of HA. From results of colorimetric method, compared with HA, adsorption amount and adsorption rate of FA is more and faster, respectively. FA molecule presents on the surface of magnetite in the shape of an araneose network structure according to the ESEM images, while HA molecule appears on the surface of magnetite in the form of small flocs or microclusters. Humic substances are effective to iron ore pelletisation. Comparsion of agglomeration results show that the different mechanisms of adsorption result in varied agglomeration behaviours. Theses findings above would be beneficial to the implications of composite binder for agglomeration.  

Sep 13, 2010

By J Player, P Evans, G Sweby

Achieving quick underground access after the completion of an open pit mine can be critical to maintaining project value and ensuring regular ore feed to the mill. This paper outlines the design and construction for two portals in an active open pit to commence underground development quickly whilst installing appropriate ground control to maintain long term access in an uncertain setting. Implementation of the portal designs was complicated by the change in underground design from hangingwall access to footwall access late in the life of the open pit due to preferable ground conditions. The portal locations did not have easy access for ground support installation integrated into the pit design due to the timing of the underground design changes. Practical implementation of the ground support systems subsequently became a key part of the project. Intact rock strength, rock mass characteristics, gradational weathering / alteration profile and structural information were modelled against pit displacement monitoring as the basis from which the portals were located and ground support schemes designed. Conditions around one of the portals necessitated numerical modelling to estimate the appropriate level of ground control for long term stability. The design was completed whilst the open pit was actively on-going and the portal areas not entirely exposed. The rock mass assessment and analysis for the two portals indicated different ground support scheme capacities would be required. The expected level of control for one of the portals also necessitated the use of monitoring with extensometers and load cells to ensure the rock mass response and ground support scheme performed as planned. Construction of the portals demonstrates the benefit of a considered design process, a plan which allows practical installation of ground support schemes where access is limited, the benefit of ongoing monitoring to ensure performance remains within design limits and the challenges involved working within an active pit with limited floor space.

Mar 15, 2021

By Morrison R. D

This paper describes major events in the design, construction, camtissioning and operation of the Elura concentrator. It covers the period fran September, 1974 when laboratory testwork on drill core cotmenced to March, 1983 when the concentrator catmenced operation on run of mine ore following successful completion of initial ccnmissioning tests. The concentrator was designed to treat 1.1 million tonnes of lead-zinc-silver ore per year with a plant availability of 89 per cent. This treatment rate has been achieved for test periods.

Jan 1, 1983

By O C. Aitken

Mining project developers are committed to taking on all the challenges and obligations of financial risk management. It is interesting that our current models of project finance have not changed markedly in principle for some 700 years, yet the rules which prepare the way for effective project assessment and subsequent loan management still do not seem to be well understood by project or corporate developers. Probability and gravity fill the opposing trays of the golden balance of financial risk. Understanding the relationship between these opposing, but intimately related elements is critically important for successful risk management. It is important to move beyond the qualitative approach and use quantitative methodologies to measure the financial impact of the occurrence of each major risk. We live in a world where the only constant is change and thus it is not surprising that a bankerÆs life is still governed by assessing, measuring and pricing risk. Banks are attracted to funding well managed companies with strong cash flow projects. But we are more risk averse compared with the credit appetites of late last century. This attitudinal shift has resulted in tougher term sheets for the early 21st century, encompassing more conditions, warranties, undertakings and stronger cash sweep provisions. Banks require well balanced portfolios to achieve an acceptable spread of risk, thus there is a more restricted market for small company lending than that available to large multi-project corporate entities with less concentrated risk profiles. Because of this focus, junior company debt finance remains comparatively expensive and especially so for more challenging geographical and political environments.

Jan 1, 2004

By T A. J Hopper, S Mukkisa, M L. Johns, K T. O’Neill

Technological advances the sensor design and performance for logging while drilling (LWD) instrumentation offer considerable opportunities in iron ore exploration. Here we focus on the development of a nuclear magnetic resonance (NMR) LWD tool. NMR is an advanced geotechnical logging technology capable of providing in situ measurements of the porosity, pore size and permeability of the formation of interest. The ability to provide real-time characterisation of iron-ore systems is beneficial to both drilling operations as well as real-time formation evaluation. The development of an NMR LWD tool for mineral exploration drilling has previously not been achieved due to the significant technical and environmental challenges associated with the design and operation of such a tool. The tool outlined in this work is designed to work in reverse-circulation (RC) drilling systems. As such, the tool needs to be compatible with the RC drill-string, as well as being highly robust to survive the shocks and vibrations experienced during RC drilling operations. The magnetic physics of the probe must be capable of measuring at the appropriate depth into formation whilst being subject to the array of motions experienced during drilling operations. Furthermore, conducting accurate NMR measurements in an iron ore formation is challenging and the measurement methodology must be tailored to characterise the magnetic environment. The tool also requires high-powered electronics capable of operating the necessary pulse sequences for excitation and acquisition. The resultant tool design must therefore optimise the inherent trade-offs which exist between the physical components (ie mechanical structure, magnetic components and electronic hardware) in order to operate appropriately whilst not hindering RC drilling operations. Current experimental analysis of the prototype indicates that the current probe design exhibits the required measurement specifications and is nearing field testing. Future work will look towards commercialisation of the instrument.

Nov 8, 2021

By B Smith, R Gelson

Springvale Colliery is an underground longwall mine situated approximately 10 km north-west of Lithgow in the western coalfields of New South Wales. Following a full-scale review of the mineÆs ventilation system in mid-2010, it was clear that the mine by early 2013 would become ventilation constrained as a result of the increasing size of the mine workings, the predicted worsening tailgate conditions and plans to introduce a fourth continuous miner unit. This realisation led Springvale to embark on a major upgrade of the mine ventilation system that would meet short-term and life-of-mine (LOM) requirements.Included in the upgrade project was the installation of a new high pressure centrifugal main exhaust fan that is capable of overcoming the high resistances imposed frequently on the circuit by restrictions in the tailgate airway. The new fan featuring a 2.5 MW motor is designed to be capable of operating at a quantity of 250 m3/s at a pressure of 7.9 kPa, a substantial improvement over the previous system, which had an operating duty of approximately 145 m3/s at 1.9 kPa. The new fan is of a centre hung design and features a backup diesel motor to maintain ventilation in the event of a power outage.Structural engineering analysis determined that under the operation of the new main fan the existing standard of ventilation control devices (VCDs) at Springvale would not be adequate to withstand the increase in differential pressures. As such, an upgrade of critical VCDs was undertaken utilising a novel high flexural strength (9 MPa) shotcrete and thin spray-on liner, which help serve to safeguard the structural integrity of the appliances and prevent increased leakage as roadway conditions at VCD sites deteriorate over time (a serious problem in many areas of the workings at Springvale).In addition to the main ventilation system upgrade, a separate upgrade focusing on improving development face ventilation was also undertaken. This upgrade included the purchase of two high capacity (22 m3/s) variable inlet vane (VIV) auxiliary fans to facilitate comfortable development face ventilation.The upgrade of the mine ventilation system at Springvale has been three years in the making, but has removed a major business risk in that it has afforded mine planning and operational flexibility (a fourth unit can now be introduced) for the LOM, and importantly provided unprecedented levels of comfort to operators at the working faces where previously ventilation and heat issues were frequently reported. The impact of this on the morale of the workforce, and hence their output, should not be underestimated.CITATION:Gelson, R and Smith, B, 2013. Life-of-mine ventilation system upgrade at Springvale Colliery - A case study, in Proceedings The Australian Mine Ventilation Conference , pp 79-86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

The Ardlethan tin concentrator had dete riorated considerably in metallurgical per- formance, maintenance and plant availability. This problem was compounded by low tin prices and International Tin Council quotas. Mid- 1976 figures were: throughput - 1300 tonnes per day, availability 83% and metal recovery 537. Major problems existed throughout the circuit from crushing to tailings disposal and with morale, staffing, and housekeeping. With the lifting of the quotas in June 1976, management provided funds to implement a major rehabilitation programme and some fifteen major projects, at a cost of about $1.3 million have been completed to date. The change in performance has been dram- atic, and end of 1977 performance figures are: throughput - 1700 tonnes per day, availability 90% and metal recovery 65%.

Jan 1, 1978

By B Shi, Y Li, L Ma, F Zhou

Subsurface fires are a common threat to coal mining, as spontaneous combustion of coal can potentially result in gas combustion and explosion. Fire-proof techniques, such as grouting, foam, or colloid injection, are not in a position to function ideally, due to the limited coverage and stopping the extinguishment substance from reaching the fire location. Liquid nitrogen, as a kind of all-submerged fire prevention or extinguishing method, can rapidly extinguish fires, thus preventing gas explosion and minimising extinguishment time. Injecting liquid nitrogen through boreholes is an important way during the period of mine catastrophe. But liquid nitrogen is not effective enough in infusion; technical issues restrict the development and utilisation of liquid nitrogen fire prevention and extinguishing technology. Immediate infusion of liquid nitrogen is usually associated with ‘air slug’ (the balloons and bubbles in the pipeline which hinder the flow of low-temperature liquid), which blocks pipelines for liquid nitrogen injecting. Another issue is that the pipeline tends to be damaged due to freezing, which undermines the injecting efficiency of liquid nitrogen and its application result. In order to solve the problems of the low efficiency and some other related field issues in liquid nitrogen perfusion, the ground–underground high efficiency liquid nitrogen injection technology were developed. Implementation of liquid nitrogen infusion techniques in Chinese coalmines achieved the goals of fire prevention and air-cooling. The technique presented in this paper is efficient in absorbing heat, and consequently, displacing oxygen and combustible gases. Field tests at Rujigou and Yangchangwan Coalmine justified the efficiency of the technique. By using this technique, there was no waste left behind, which may impede the subsequent production. The presented technique is of great benefit to the social, economic, and environmental aspects of mining operations, and will have broad applications in fire prevention for large-scale coalmines.CITATION:Zhou, F, Shi, B, Li, Y and Ma, L, 2015. Key techniques and engineering applications of stereoscopic liquid nitrogen infusion for coalmine fire prevention, in Proceedings The Australian Mine Ventilation Conference, pp 291–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Kewu W

Kaolin used as an industrial mineral, especially that in the paper-manufacturing industry, must be of fine size, with high brightness, a low impurity content, and good crystal shape. However, in most kaolin deposits there are various impurities which have a very bad effect on the quality of the kaolin. Therefore, it is necessary to remove these impurities from kaolin ore. Owing to their similar surface properties, the separation of kaolin and iron oxide minerals, especially microkaolin and iron oxide minerals, has been regarded as difficult. The iron oxide minerals often intergrow with kaolin in fine and complicated forms, such as thin films, which make separation difficult. In order to overcome this difficulty, many workers have suggested various treatment methods and obtained great success. Based on research work by Fuerstenau (1980), Huang, Li and Hu (1984), Hui and Wei (1991), Shergold (1978), and Zambrana et al (1974), we have investigated a two-liquid flotation technique for iron removal from kaolin and obtained some success.

Jan 1, 1993

By D Xu

BHP Billiton Iron Ore is one of the world’s premier suppliers of iron ore. It currently has operations in Western Australia and Brazil and also has some iron ore interests in West Africa.BHP Billiton’s Optimisation R&D team has developed a proprietary mine planning optimisation tool that uses a mixed integer linear programming (MILP). This tool is called Blasor and it is used to rapidly evaluate the resource development potential (RDP) scenarios for the company’s business development strategy. In addition it generates life of asset (LOA) mine plans for the company’s operations and growth projects. The Blasor optimiser maximises the discounted operating cash fl ow (DCF) as the objective function, subject to mining, processing and transportation capacity constraints and blended product quality constraints. The paper will outline how Blasor has been applied to the resource development potential (RDP) strategy scenario studies, growth project evaluations and LOA mine planning within BHP Billiton Iron Ore.The practical application of Blasor to resource planning optimisation within BHP Billiton Iron Ore has demonstrated the value of such a tool for optimising strategic directions through the evaluation of a number of carefully proposed scenarios and maximisation of operational decisions, such as cut-off grade, open pit development sequence, etc. Particularly for the company’s business development direction studies, Blasor plays the role of a fair valuation tool in that it discovers the most valuable resource development scenario, thus establishing a sound basis for comparing the economic merits of each scenario.

Jul 11, 2011

By Buttrose RB

The Pine Creek gold mining development consists of a 1000000 tonne/yr open cut mine, a carbon-in-pulp processing plant and support facilities. The operation is located at Pine Creek, 230 km south of Darwin in the Northern Territory. The mine was officially opened in late October 1985, having been designed and constructed in less than twelve months, despite front end expenditure constraints and unseasonal cyclonic rains shortly after commencement of site activity. Non-traditional methods and attitudes were required to be adopted by both Engineer and Owner to successfully bring the project from preliminary design through construction and commissioning in a minimum time. Those areas which differ from the more traditional approaches to Project Management are examined together with a review of the advantages and penalties of these methods.

Jan 1, 1986

By Niemann G

The paper addresses certain mining provisions of the Aboriginal Land Rights (Northern Territory) Act 1976 and the development of Mining agreements negotiated pursuant to Section 43 of the Act. Difficulties for miners and Land Councils alike arising out of the operation of the Land Rights Act will be discussed. Possible scenarios for the resolution of these difficulties will be proposed.

Jan 1, 1984

By M J. Nugus

The structural models developed by exploration and mining geologists are most commonly concerned with the ‘main structures’ or key constituents that pertain to the associated mineralisation. To this end, it is recognised that the geological and exploration models, which are developed, are essentially ‘fit for task’ and the scale-related variances are not always realised at an early stage. In fact, in many cases anomalous intercepts along different trends and of variable apparent continuity have often been neglected as ‘back scatter’ and not important. Recognition of the importance of subordinate structures as mineralising hosts suggests that additional opportunities exist outside the primary and main structures. History shows that opportunities are often not realised where gold is hosted in orientations not parallel to the predominant trend of the schistosity, main fault or shear zone.Another reason for the importance of subordinate structures can be understood from their roles in a percolation network. Subordinate structures can access the large fluid fluxes provided by backbone elements, but, as dangling elements, they provide greater opportunities for gold precipitation mechanisms and hence may constitute essential parts of the resource. Therefore, the role, understanding and consideration of the smaller-scale and orthogonal structures should be considered during all facets of exploration, resource development, delineation and mining.

Aug 22, 2011

By M Griffiths

This paper outlines an approach to high solids slurry pipeline design with data generated from a closed pipe-loop test system. The pressure and flow rate data generated is used to develop a pseudo-shear diagram for the purposes of system design. Following this approach enables the design of a full pipe flow system maximising system life and reliability. The alternative free fall system is explained and the disadvantages highlighted.Environmental and social considerations are discussed; mainly water and land use, and how designing for high solids slurry pipeline systems can be used improve these aspects of a mining project.Also discussed is how the use of high solids slurry pipeline systems can help to mitigate the risk associated with surface tailings storage facility failure, with the Bulyanhulu project used as a positive example.

Aug 8, 2011

By E J. Y Koh, G J. McLachlan, E Amini, N Beaton

Preconcentration greatly reduces the ore mass input to the processing plant while upgrading the grade. One of the commonly used methods of preconcentration is optical sorting. These methods rely on optical sensors which classify the material stream into “accept-reject” streams. Currently, it is common to use near infrared (NIR) or colour cameras to classify streams based on reflectance or colour thresholds set by experts. The imaging is done through line-scan sensors where the material is scanned on a belt or a chute. Then, a separation apparatus like a diverter gate or air jet is controlled to separate the streams according to the classification made by the algorithm. Separation efficiency is dependent on the classification algorithm. Existing classification algorithms rely on low-level feature discrimination like observing individual pixel values for reflectance or colour hues. This limits discrimination between minerals with low contrast in colour. Human experts perform mineral segmentation using texture, colour distribution and shape, but it is difficult to translate these visual rules to mathematical thresholds. Deep learning methods like Convolutional Neural Networks (CNNs) provide high-level feature discrimination similar to a human expert. Instead of relying on pre-defined features, the CNNs learn complex features from the dataset. CNNs can construct a hierarchy of features based on pixel clusters to learn texture, shapes, and colour spectrums of the mineral grain surface to provide better separation. In this study, a state-of-the-art deep learning instance segmentation method is used to outline boundaries and classify grains from the background (mineral segmentation). The algorithm is trained on images collected from a flotation feed of a gold deposit, where the gold is mechanically locked inside pyrite. This method can process on-line video inputs at 5 frames per second to provide a live grade. The proposed method is inexpensive as it only uses a camera and a desktop computer.

Nov 10, 2020

Between, 1980 and 1984, the demand for non- ferrous metals in the free world grew annually by 1.5 per cent for copper, 0.4 per cent for lead, 1.4 per cent for zinc, and 2.5 per cent for nickel. The growth rate decreased substantially compared to the rate experienced before 1980, and was far lower than the GNP growth during the corresponding period. The main reasons for this are considered to be 1. resource-saving efforts by industrialized countries resulting from the first and the second oil crises, 2. saturated demand for durable consumer goods, and 3. substitution of non-ferrous metals by new materials such as optical fibers.

Jan 1, 1986

Blasting is an essential component of most mining operations, and is used to reduce the rock mass to a workable size distribution, as well as to create stable openings and pit walls. Frequently, there is little difference between the designs of blasts to achieve these two functions, though more advanced operations have developed different designs for these very different functions. To assist in the appreciation of how blasting practices can impact on the stability of rock openings and pit excavations, this paper reviews the role of high pressure explosion gases on final block stability. It is assumed that the stability of all surface and underground excavations are, to a greater or lesser extent, controlled by the interaction between discrete rock blocks. Typically, these blocks will be defined by either natural, or excavation induced, jointing.

Jan 1, 1999

The Telfer Underground sublevel cave (SLC) Operation is located approximately 850 m below surface. The cave was designed to propagate through an old decline which was initially used to monitor the cave. There was a requirement to install air blast plugs at two locations in the old decline in order to isolate any potential air-blasts from the active workings in the event of the rock mass collapsing into the cavity. There was a further requirement for an air-blast plug in another section of the mine where there was a risk of the cave intersecting an old workshop and providing an air-blast pathway through an abandoned incline. The design criteria for the plugs was that they should withstand the design air blast loading, be free draining, cost effective and easily constructed with the mining expertise available on site. A plug consisting of grouted mullock was considered robust and least challenging to construct. For the purpose of estimation of maximum air pressure on plugs, it is supposed as a worst case that the rock above a cave falls as an airtight piston onto the top of a muck pile, forcing air into it and also mine workings intersected by the cave. Airflow through the muck pile is governed by Ergun's equation for turbulent flow. In a time-stepping integration scheme, transient air pressures and velocities are calculated according to equations of thermodynamics, in the cave and at intervals along intersected drives by means of a finite difference spatial discretisation. The ability of plugs to withstand computed pressures is assessed by finite element elastoplastic analysis. This paper outlines the rationale for potential air blast loading, calculation of transient air pressures, plug design and analysis of plug behaviour. The plug construction method is also discussed.

Nov 25, 2010

By G Haywood

This paper presents the evolution of the planning, scheduling and mining practices at the Yilgarn Star underground. The paper will concentrate on the principals of æjust in timeÆ and the impact of such practices on mine planning and scheduling and subsequent development and production. The principals of æjust in timeÆ were developed to minimise the impact of creep and time dependent failure of the ground in the ore and hangingwall zones. These zones are characterised by altered schistose material with inherent weak rock strengths compounded, at depth, by the maximum principal stress of the virgin stress field approaching the UCS of the rock mass. Yilgarn Star underground has and continues to develop the æjust in timeÆ methodology to ensure the continued viability of the mine. The mine continues to use longhole open stoping mining methods to ensure high levels of productivity with minimal dilution and at an acceptable cost of production.

Jan 1, 2002