Search Documents

By M. Yoshinuga, S. Watanabe

Some iron ores, sinters and pellets occasionally show abnormal behavior during reduction which makes them undesirable as blast furnace burden. These may be divided into the following three types: (1) decrepitation of iron ore, (2) swelling of iron ore and pellet, (3) size degradation of sinter. In this paper reduction experiments and microscopic examinations were made to clarify the mechanisms and causes of these abnormal phenomena. Decrepitation occurs mainly when compact hematite ores containing small amounts of limonite are heated to about 500°C. Abnormal swelling of ores and pellets is caused by the rapid growth of fibrous metallic iron from the surface of wustite grains during rapid reduction and is fundamentally related to their original microstructure. Size degradation of sinter occurs through the development of cracks in the reduction stage from hematite to magnetite. About 80% of the iron ore used in Japan's blast furnaces comes from abroad, and the iron and steel industry must import this raw material from distant overseas places at high freight rates. The blast furnace operators, therefore, have made strong efforts to cut costs under these restrictive raw materials conditions by increasing productivity and simultaneously decreasing coke consumption. If, however, a high proportion of the ore burden consists of unsuitable materials furnace irregularities often result, establishing the need for detailed investigations of the basic natures of the ore constituents and their reactions during the reduction process. Recent investigations '-' of various ore burdens suggest that some iron ores, sinters and pellets are occasionally abnormal in appearance and behavior during reduction studies and may prove to be undesirable for use in the blast furnace. In the present study reduction experiments and microscopic observations were made to clarify the causes and the mechanisms of the abnormal behavior observed in some constituents of the burden and their effect on blast furnace performance. REDUCING APPARATUS The four kinds of reducing apparatus used in this investigation were the following: 1. The JIS* (Modified Gakushin') apparatus shown in Fig. la is most commonly used in Japan to evaluate the reducibility of ores under static conditions. It consists of a stainless steel tube of 60 mm inside diam suspended from a balance. 2. Linder's Reduction Test apparatus (Fig. lc) has a reducing barrel 130 mm diam and 200 mm long which rotates at 30 rpm. Some modifications were made in test procedures. 3. Gakushin Standard Test apparatus for determining the reducibility of granular ores (Fig. Id) consists of a horizontal silica tube 32 mm diam, 370 mm long and a movable electric furnace which enables rapid heating and cooling of the specimens. 4. The test apparatus for reduction under load (Fig. lb) gives a comprehensive evaluation of the behavior of ores under conditions simulating the static loading and the chemical reduction conditions encountered in. a blast furnace stack. A stainless steel tube of 50 mm diam and a carbon rod of 35 mm diam were used as the sample container and the support for the weight, respectively. In each investigation care was taken to select the most suitable method and apparatus to distinguish the abnormal nature of the ore in question. SIZE DEGRADATION OF SINTER DURING REDUCTION Sinter makes up the major portion of the blast furnace burden and its behavior during reduction should bear a close relationship to the iron productivity. Recently, some of the sinter was found to show serious size degradation during reduction at a relatively low temperature range. Because this phenomenon was thought to be a possible source of furnace irregularities, tests were made to clarify the phenom-

Jan 1, 1969

By M. Ahlers, Horace Pops

Slip features and formation of stress-induced mm-tensite have been studied in single crystals of fl phase Cu-Zn alloys in the composition range between 43 and 48 at. pct Zn. A phenomenological analysis is presented in which the glide planes and directions that me associated with the inhomogeneous shear in the martensite phase are predicted from the experimentally determined habit planes and macroscopic shear directions. It is shozun that the resolved shew component of the applied stress on the secondary shew system is a very important factor governing the formation of stress-induced martensite. A comparison is made between martensitic phases that form spontaneously upon cooling and those phases that arise from deformation. THE ß phase in Cu-Zn alloys is unstable and may transform spontaneously by a martensitic transformation1-3 during cooling. Thermoelastic and burst-type spontaneous martensitic phases have been observed3 in the composition range between 38 and 42 at. pct Zn. Martensite forms in alloys containing more than 42 at. pct Zn only by cold work below a temperature denoted as Md.4 Thus, alloys near the equiatomic composition can undergo a stress-induced transformation upon cold work at room temperature. Although data have been obtained concerning the effect of temperature5 and composition4 on the deformation of polycrystalline Cu-Zn alloys, it is rather surprising that few detailed studies6-8 on 6 brass have been conducted for single crystals where the stresses acting on crystallographic planes can be determined. A thorough understanding of transformation mechanisms requires knowledge of the role of stress and plastic strain. With this objective in mind we have made an investigation of the stress-induced rnartensite transformation in single crystals of 0 brass in the composition range between 43 and 48 at. pct Zn. Particular emphasis is given to the morphology and crystallographic features and a comparison is made between stress-induced and spontaneous martensite. I) EXPERIMENTAL PROCEDURE Master alloys having nominal zinc contents of 43, 45, and 48 at. pct were prepared from spectroscop-ically pure metals (>99.999 pct) in sealed quartz tubes under a partial pressure of helium. These alloys were cut into several pieces and converted into small rods by melting in quartz tubes. Subsequently, single crystals were grown from the rods by the Bridgman technique and homogenized for 3 hr at 820°C. Lattice parameter measurements were made from stress- relieved filings. Compositions, as determined from the reported variation of lattice parameter with atomic percent zinc,' indicated a zinc loss of less than approximately 0.25 at. pct. The single crystals were electroturned using a phosphoric acid electrolyte into tensile specimens each with a center section of 1 mm diam and 1 cm gage length. Cylindrical specimens approximately 3 mm in diam and 10 mm long and spark-machined rectangular blocks approximately 3 by 3 by 10 mm were prepared for compression studies. These blocks were stress-relieved and electropolished to eliminate any stresses introduced by spark machining. Crystal orientations were determined to an accuracy of ±2 deg primarily from back-reflection Laue photographs, and sometimes by the rotating single-crystal method. Figs. 1 to 3 show the location of the tension and compression axes within unit stereographic triangles. All specimens were deformed plastically at room temperature using an Instron machine, the crosshead speed being 0.02 or 0.05 cm per min. A hard steel hemisphere was placed at the upper end of the compression samples to achieve uniaxial loading. Trace normals of slip markings and habit planes of strain-induced martensite were determined to an accuracy of ±4 deg from the rectangular blocks by a two-surface analysis and from cylindrical specimens by measuring the angle between the tensile (or compression) axis and the tangent to the surface trace for different rotations about the deformation axis. Slip

Jan 1, 1969

By A. J. Phillips, C. G. Grant, Wm. B. Price

ADMIRALTY nickel is a new corrosion-resisting and heat-resisting white metal alloy composed of 70 per cent. copper, 29 per cent. nickel and 1 per cent. tin. It has been given the trade name "Adnic." In 1924, Wm. B. Price1 described this alloy and its successful use as a diaphragm metal. The physical properties of Adnic at ordinary and elevated temperatures were given in Mining & Metallury.2 A patent3 was granted on Adnic, April 28, 1925. Work was first started on this alloy during December, 1921. An investigation of the patent situation in this country and abroad, and also a search of the literature, did not reveal any work on the ternary diagram, copper-nickel-tin; and the only wrought copper-nickel-tin alloy found was that known as "Newloy," composed of copper, 64 per cent.; nickel, 35 per cent.; tin, 1 per cent. This was being manufactured and sold by Wm. Gallimore & Sons, Ltd., Sheffield, England, for unplated spoon and fork stock, and first came to our attention in January, 1922. The preliminary work in connection with the development of Adnic was started by casting four binary copper-nickel alloys of the compositions shown in Table 1. Various amounts of tin were added to each of these mixtures, to produce the series of ternary copper-nickel-tin alloys also given in Table 1. A 200-gm. sample of each of these was cast by melting in a clay graphite crucible and allowing the melt to slowly cool with the furnace. A longitudinal section from each of these castings was polished and etched for examination. The castings were not homogeneous solid solutions, but showed the usual cored structure associated with cast alloys. However, from an examination of these sections we roughly determined

Jan 1, 1928

By Donald L. Johnson

REVIEWS on the applications of optical ellipsometry to the study of polycrystalline metal surfaces and oxidation-corrosion processes have been presented by Kruger and Hayfield, and white.' In view of the ability of this method to measure differences in film thicknesses to below 10A, ellipsometry was used to study nitrogen chromium surface reactions during the early stages of growth. Chromium specimens in the form of a vapor-deposited film on glass substrate were exposed to purified nitrogen for selected time increments at 700°F. This temperature was selected because it gave the best combination of exposure time and thickness change. Ellipsometer readings were taken immediately after exposure to determine polarizer and analyzer angles using monochromatic light at 5000A.2 After each set of readings was obtained, the specimens were exposed for an additional increment of time in nitrogen and a new set of readings taken. Film thickness was computed from LUCy's3 equation for nonabsorbing thin films. In Lucy's derivation, two equations for computing thickness were obtained. Peterson and Bashara4 have discussed the validity for using one of these equations when an independent value of the refractive index is used. The film was assumed to be Cr2N (Ref. 5) and was determined to be optically isotropic. Optical isotropy was determined by rotating the films about the surface normal and noting that the azimuth and phase difference did not change. Since Cr2N is reported to be hexagonal, it is assumed that optical isotropy results from randomly oriented grains of very small size. The thickness was computed using refractive indexes varying from 1.6 to 2.0. The maximum variation in computed thickness over this range for a given exposure was 20 pct. The data reported are based on a refractive index of 1.8. Reference readings on the metal surface were taken just prior to nitrogen exposure. No attempt was made to deoxidize or denitride the metal surface after vapor deposition, although specimens were observed to gain approximately 2A per day in air at room temperature. Twelve experimental exposures were made on a single sample over a total accumulative time of 132 min. Additional experiments over longer time intervals were made to determine the effect of heat up and cool down during and after exposure. As a result of these experiments, the thickness computed for each exposure was increased by 4A. Time profiles based on the linear law are similar to the oxidation profiles for many metals.' The rate of accumulation of the nitride film is rapid at first and slows down as the film thickness increases. The parabolic law x2 =k1t +k2 [11 gives a straight line in Fig. 1; therefore, it is concluded that the kinetic behavior is parabolic. Sey-bolt and Haman5 reported similar results for CrlN on chromium at 1000°C although the order of the thickness was much greater (10-3 cm). Analysis of thickness data based on other values of refractive index shows that the curves are shifted vertically but retain the same shape. According to Mott,7 it is expected that for thin films k2 is zero in Eq. [I]. Since the plot in Fig. 1 is linear through the origin, k2 is zero and the parabolic nature of the film growth is further indicated. The parabolic rate constant, calculated from the slope in Fig. 1, is 4.4 x 10-16 sq cm per sec. The corresponding work (+) required to bring an electron from the metal into the oxide is estimated to be 1.5 ev.7 The author thanks professor N. M. Bashara and D. W. Peterson, Electrical Materials Laboratory, University of Nebraska, for making the ellipsometer available and providing technical assistance. The Electrical Materials Laboratory is supported by the office of Naval Research, NONR 3718 (01). This work was partially supported by the Engineering Experiment Station and the Mechanical Engineering Department, University of Nebraska.

Jan 1, 1967

By H. W. Rogers

The first steam shovels used in this country were built by the Otis Company, of Boston, about 50 years ago, but as they were of very crude construction and rather unsuccessful only a few were built. For possibly 10 years prior to 1884 successful steam shovels were made and used on certain classes of work, but it was not until that time that they were manufactured in quantities and began to play an important part in all classes of excavation. From that time up to the present day there have been gradual but continuous improvements on the original shovel, not only in the mechanical construction, but also in the design of boilers and engines which are best adapted to this class of service. In proposing a change from steam to electric operation we have to deal with a steam equipment which has not only proved its worth but has probably reached its highest stage of development and efficiency. That the electric shovel is a possibility cannot be denied, as at present from 12 to 18 shovels are in operation in this country. These shovels may be divided into three classes: the friction electric, which is operated by a single constant-speed motor with friction clutches; the three or four motor direct-current equipment, and the three or four motor alternating-current equipment. It is the second and third classes that I wish to deal with, as the first class does not compare favorably with the steam shovel so far as speed is concerned, although it may be operated as cheaply. There is probably no other class of machinery that presents a duty cycle as severe as that of the shovel, which is very short, varying from 7 to 12 sec. on the hoist, from 7 to 12 sec. on the thrust, and from 10 to 18 sec. on the swing, making a complete cycle in from 17 to 30 sec., and the motor to meet these requirements must have a sufficiently low armature inertia to permit of rapid acceleration and quick reversals under small power. It should also be a motor of rugged design, as it must be subjected to severe overloads and shocks and frequent reversals. This is especially true of the hoist motors and, to a lesser degree, of the swing motor; the thrust motor being practically stalled during the digging operation, although it may revolve or overhaul, according to conditions, and is operated at full speed only after the hoisting operation is completed.

Jan 1, 1915

By Hans Lundberg

FOR the last 20 years, geophysical methods have been in practical use. The results accumulated during this time have been broad enough to enable us to formulate some general rules for conducting geophysical surveys to the best advantage. It is a well established fact that electrical and magnetic methods have aided the geologist to outline bodies of ore, to differentiate between various types of rocks hidden from view and also to determine the thick-ness of the layer of drift that covers the bedrock. Fundamental require-ments for a successful solution of a geophysical problem is the existence of physical differences between the various formations under investiga-tion. If such conditions exist, our problem becomes a physical, mathe-matical and geological analysis of the effects of these differences upon the structure of an arbitrarily produced, or already existing, field of force. Experience has shown that reliable and consistent results in analyzing such fields of force are obtained only if: (1) the methods and apparatus used are scientifically sound and designed to provide information with a maximum amount of accuracy, reliability, sensitivity, simplicity and speed of operation, and (2) the interpretation of the results of such an investigation is guided not only by rigid mathematical rules but also by common sense, based upon sound geological knowledge and imagination. Today, a number of methods are based upon sound principles, are highly sensitive and are well suited for field work. The instrumental developments have resulted in self-contained instruments, which permit the determination of field ratios and intensities with great accuracy. Magnetic surveys have almost become standardized. The electrical methods, mostly based on the determination of potential-drop ratios, or electromagnetic field ratios, are built as bridge circuits and it is easy to determine amplitude, as well as phase relationship of the various electrical and electromagnetic fields.

Jan 1, 1938

By H. Schwartzbart, J. R. Low

Annealed, .Poly crystalline, low carbon steel exhibits a phenomenon known as the "yield point." If such a steel is loaded in tension, the load increases steadily with elastic strain, drops suddenly, fluctuates about some constant load value for a time and then rises with further strain. The load at which the sudden drop occurs is called the "upper yield point"; the load at which deformation proceeds at constant load is known as the "lower yield point"; the amount of elongation at constant load is termed the "yield point elongation." Deformation which occurs during the yield point elongation is heterogeneous in nature, deformed metal existing next to undeformed metal. The drop in load from the upper yield point is concurrent with the formation of a band of deformed metal which usually appears at a stress concentration such as a fillet and at an angle of approximately 45" with the direction of pull. As deformation proceeds during the yield point elongation, the deformed region grows until the entire specimen has been strained an amount equal to the strain in the first band. A phenomenon very often associated with the yield point is that of strain aging. Aging in steels may be of two types: quench aging, or precipitation hardening, and strain-aging. Strain aging differs from precipitation hardening in that if the metal is merely strained instead of given a solution anneal and quenched, it then undergoes changes in properties similar to those observed in quench aging. The yield point effect and strain aging are most markedly exhibited by low carbon steel, but have been observed in other alloys. Numerous explanations for the mechanisms of both phenomena have been advanced, but the evidence for the acceptance of any of the hypotheses is incomplete. One of the explanations of the yield point phenomenon frequently proposed is that there exists a honeycomb of grain boundary material that supports the load above the yield strength of the ferrite and that when this network ruptures, the ferrite flows with no increase in load. This notion was first advanced by Dalbyl in 1913 and has been since put forward in more concrete form by many investigators. The testing of this hypothesis was, in part, the object of the present investigation. Similarly, the mechanism by which strain aging occurs remains to be explained. Presumably, it is a precipitation hardening phenomenon similar to quench aging, the precipitation being initiated by strain. However, it is not known whether the process is a solution and precipitation effect or a change in solubility due to strain. One obvious method of determining whether or not the yield point is a grain boundary phenomenon is to determine if single crystals exhibit a yield point. Low and Gensamer2 have shown that carbon and nitrogen are responsible for the yield point and aging in steel and that these effects can be eliminated by the removal of these elements through wet hydrogen purification. Single crystals that have been grown in wet hydrogen treated material must then be recarburized or re-nitrided in order to evaluate the effect of grain boundaries. In the present investigation, single crystals of iron which had been annealed in wet hydrogen to remove the carbon and nitrogen were cut into two specimens having the same orientation with respect to the tension axis. Of these, one specimen was pulled in tension in the wet hydrogen treated state and the other was carburized or nitrided and tested similarly. All the crystals were examined for a yield-point and strain aging. The grain boundary hypothesis for the explanation of the yield point in steel has been tested only indirectly previously. Arrowsmith,3 Andrew and Lee,4 Edwards and Pfeil,5 Fell,6 Ludwik and Scheu,7 Winlock and Leiter8 and others found a decrease in proportional limit and yield point effect with an in-

Jan 1, 1950

Abdul-Ahad. A., Student, Montana School of Mines, Residence Hall Butte, Mont. '39 Abramovits, Charles, Student, Case School of Applied Science Cleveland, Ohio. '37 Abreu, Ovidio M., Student, Univ. of Nevada Reno, Nev. '38 Acker, Voscoe, Student, Agricultural & Mech. College of Texas College Station, Tex. '39 Adams, Albert, Student, New Mexico School of Mines Socorro. N. M. '38 Adams, Charles W., Student, Michigan College of Min. & Tech Houghton, Mich. '39 Adams, Hugh T., Jr., Student, Univ, of Oklahoma Norman, Okla. '39 Adams, Jack L., Student, Univ. of Oklahoma Norman, Okla. '39 Adams, Jack M., Student, Univ of Alaska College, Alaska. '39 Adams, Lewis J., Student, Agricultural & Mech. College of Texas, Box 2514, College Station, Tex. '39 Adams, Robert E., Research Engr., Battelle Memorial Inst Columbus, Ohio. '38 Adamson, George M., Jr.. Student, Univ. of Utah Salt Lake City, Utah. '39 Adkisson, J. F., Jr., Student, Agricultural & Mech. College of Texas, Box 1003, College Station. Tex. '38

Jan 1, 1939

MINING, to be precise, ends when the ore is delivered to a bin outside the mine. Usually the next step is concentrating; or, as it is more often called, milling. A few elementary definitions will help make clear the discussion that is to follow. A rock is an aggregate of minerals; copper ore is rock that contains copper-bearing minerals in quantity sufficient to make it profitable to mine and recover the copper in the form of marketable metal. Manifestly, under a literal interpretation, a mass of material might be copper ore one day and merely copper-bearing waste rock a week later, if the price of copper happened to drop in the interim. Emphasis already has been placed on the expansion that took place in the ore reserves of the Porphyry companies as a consequence of the great strides made in the technique of mining and ore treatment. So, even if one inserted a qualifying phrase, "at an average price for the metal," after the word "profitable," the definition would still be open to criticism. Place is another factor. It is evident that a body of excellent ore in Arizona might cease to be ore in the economic sense if it were moved intact to the interior of China. However, it is with ore in its technical and scientific aspect that this chapter is concerned. Speaking in general terms, the ton of Porphyry ore as it arrives at the surface contains 25 to 70 lb. of copper minerals in the form of disseminated particles or thin coats along fracture planes. When subjected to appropriate treatment this ton yields 12 to 40 lb. of metallic copper. These ranges take into account conditions of today and of 25 years ago. Two procedures are available: (1) concentration, followed by smelting of the concentrate, or (2) leaching and precipitation, usually by electrolytic deposition. Smelting and leaching are metallurgic processes in that they involve chemical change; concentration

Jan 1, 1933

By Donald D. Carr, Lawrence F. Rooney

Perhaps no other mineral commodity in this volume has as many uses as limestone and dolomite. These carbonate rocks are the basic building blocks of the construction industry, the material from which aggregate, cement, lime, and building stone are made. Carbonate rocks, and their derived products, are used as fluxes, glass raw material, refractories, fillers, abrasives, soil conditioners, ingredients in a host of chemical processes, and much more. Although the use of limestone and dolomite goes back before recorded history, new uses and products are continually being found. Carbonate rocks form about 15% of the earth's sedimentary crust and are widely available for exploitation. Found extensively on all continents, they are quarried and mined from formations that range in age from Precambrian to Recent. Reserves of carbonate rock are large and will last indefinitely, although high-purity deposits may be absent or have limited availability in certain areas. Limestone and dolomite are so useful and so abundant that in 1981 about 644 million tons were produced in the United States. In fact, about 75% of all stone quarried or mined in the United States was carbonate rock. Sand and gravel was the only mineral commodity produced in greater quantity. In this chapter we have sought to provide the general reader an overview of carbonate rocks, their composition, distribution, production, and uses, with emphasis on developments since 1960. In doing so we borrowed extensively from our report on the applied geology of limestone and dolomite (Rooney and Carr, 1971). The literature on the limestone and dolomite resources of the United States and Canada is so vast and diverse that one can easily become mired down in print. We tried to list those references that are easily accessible and that provide the economic geologist with a starting point for more intensive study. The table listing selected references on limestone and dolomite resources in Canada and the United States reflects our attempt to be selective rather than exhaustive and to direct the reader to the best sources of detailed information. Geology Mineralogy The principal carbonate rocks used by industry are limestone and dolomite. Limestones are sedimentary rocks composed mostly of the mineral calcite (CaCO3) and dolomites are sedimentary rocks composed mostly of the mineral dolomite (CaCO3 • MgCO3). Aragonite (CaCO3), which has the same chemical composition as calcite but a different crystal structure, is economically important only in modern deposits, such as oyster shells and oolites. Aragonite is metastable and alters to calcite in time. Some other carbonate minerals, notably siderite (FeCO3), ankerite (Ca2MgFe (CO3)4), and magnesite (MgCO3), are commonly found associated with limestones and dolomites but generally in minor amounts. Because of their similar physical properties, the carbonate minerals are not easily distinguished one from the other. Specific gravity,

Jan 1, 1983

By H. D. Outmans

The mechanics of filtration are described by a theoretical-empirical nonlinear diffusion equation which, under certain circumstances, may,be linearized and then solved explicitly. For filtration under static conditions linearization leads to a boundary value problem analogous to a heat flow problem with a known explicit solution. The corresponding solution for static filtration is compared with published experimental data. Under dynamic conditions filtration takes place in three successive stages. During each of these the rate of filtration and/or the thickness of the filter cake are different functions of the filtration time. The proposed mechanism explains the observed high resistance of dynamically deposited filter cakes against erosion and also the connection between filtration rate and viscosity of the drilling fluid. Several of the quantities governing dynamic filtration have no counterpart in the static filtration mechanism. The static filtration rate is, therefore, not a reliable measure for the dynamic rate and vice versa. INTRODUCTION Filtration under simulated borehole conditions, i.e.. either from a static suspension or from a suspension flowing parallel to the filter cake (dynamic filtration), has been the subject of several laboratory studies.1-7 This experimental and theoretical work showed that many aspects of the filtration mechanism cannot be explained by an elementary filtration theory based on the assumption that the filter cake is incompressible. For a more satisfactory theory compressibility should be taken into account. This has been done. at least to some extent, in the filtration theory developed for the chemical industry. Surveying the literature (see Ref. 8 for a bibliography) it becomes apparent that, although several properties of filter cakes deposited from many different suspensions have been measured, including compressibility, the filtration equations are essentially empirical in nature. No attempt has been made, for instance, to develop filtration theory along the lines of consolidation theory.12 This theory, upon which a highly successful development in soil mechanics rests, would appear to be an excellent starting point for a filtration theory since the compressibility concept is an essential part of it. As we will use this theory in the following development it is well to state the four assumptions on which it is based: 1. The fluid flow through a compressible porous medium is governed by Darcy's law. 2. The rate of change in fluid content of an element of the porous medium is proportional to the rate of change of solid pressure between the particles. 3. The solid particles are incompressible within the range of pressures considered. 4. The total pressure on a surface normal to the line of flow is equal to the sum of the fluid pressure and the pressure between the particles (solid pressure) at that surface. To calculate the rate of filtration and other quantities of interest it is necessary to know the filter cake compressibility and the permeability as a function of the solid pressure. It has not been possible to calculate these functions from theoretical considerations and they will therefore be introduced in this paper as empirical expressions. Both are determined in a compression cell where the cake is subjected to a mechanical load. Permeability and compressibility are measured after the solid pressure has stabilized, i.e., after the excess fluid pressure has been dissipated and the uniform pressure is transmitted entirely by the solids. The permeability and compressibility thus determined are not the same as during filtration in the borehole, under either static or dynamic conditions, because then, due to frictional drag, the solid pressure and hence also the permeability and compressibility vary along a line normal to the direction of the mean flow and can only be defined locally. DERIVATION OF THE FILTRATION EQUATION FOR COMPRESSIBLE FILTER CAKES As the filter cake in the borehole is thin compared to the radius of the hole the filtration may be considered as linear. Taking the x-axis normal to the wall, with its origin at the formation, we have, according to Darcy's law,

Jan 1, 1918

By John L. Walter

A sintered compact of iron containing 0.007 vol fraction of glass , prepared 6). powder rnetullurgtcal lechniques, was rolled lo foil, 0.001 in. /hick. The foil sullrples were anneuled a1 650° to 850°C in hydrogen. Pri,narj recryslullization prodtnced large grains which Lc3ere highly elongnled in the rolling direclion und which had an unusual prgferred orientation. The glass parlicles assumed a stringerlike dispersiorz on working; llie slrinyers were parallel lo the rolling direction and to the long axis of the grains. The same unusual grain structure, preferred orientation, and stringerlike dispersion of purticles are found in heal-ily rolled and annealed foil of tungsten which has heen doped wilh small amounts of aluminum, silicon, and polassiutvt. Both the proper dispersion of the particles and severe working (reductions in excess of 98 pct) are necessary to produce the elongzcted grain structure. RECENTLY, the author reported on the origin of the elongated or "nonsag" grain structure in tungsten foil which was doped with aluminum, silicon, and potassium.' It was observed that particles, identified as mullite (Al6Si2Ol3), were present in the doped ingot (as sintered) and at all stages of processing from ingot to sheet or wire. It was shown that the particles, being plastic at tungsten working temperatures (up to 1550"C), underwent a "stringing out" parallel to the working di-direction. It was concluded that these strings of particles were responsible for the formation of the highly elongated interlocking grains observed in doped tungsten wire or sheet. To give further credence to this explanation of a long-observed but not understood phenomenon, it was decided to design a new system, one which was analogous to the doped-tungsten system. Thus, a bcc metal, iron, was chosen to be doped with glass which would be plastic at reasonable working temperatures for iron. The glass chosen was a #0080 Corning lime glass which melts at about 810°C. This is approximately the same fraction of the melting point of iron (0.6) as the melting temperature of mullite is of tungsten. It will be shown that all the observed unusual features of the doped tungsten are duplicated in the glass. doped iron, even to the preferred orientation of the grains in the recrystallized sheet. In the tungsten sheet the preferred orientation consists of two components, (1i3)(691) and (013)(362), neither of which has been observed as a component in textures of primary recrystallized bcc metals. EXPERIMENTAL PROCEDURE The glass, in the form of fine powder, was added to high-purity electrolytic iron powder and mixed dry. The particular composition chosen was 0.007 vol fraction of glass. After mixing, the powder was mechanically pressed to a disk 0.5 in. diam and 0.15 in. thick at a pressure of 5000 psi. The pellet was sintered, in pure dry hydrogen, for 2 hr at 8 50°C. The sintered pellet was then heated to 750°C and rolled to 50 pct reduction of thickness in two passes, with reheating between passes. The rolling temperature was then reduced to 600°C and the slab was rolled to a thickness of 0.050 in. Rolling to 0.010 in. was accomplished in several passes at 300°C. Final reductions to 0.003 and 0.001 in. were taken at room temperature. This rolling temperature schedule was similar, in terms of the fraction of the melting point, to that used in the rolling of the doped tungsten. The total reduction of thickness was in excess of 99 pct. Samples of the rolled foil were lightly electro-polished and annealed for 1 to 6 hr at temperatures of 650" to 85O°C in hydrogen. Samples for transmission electron microscopy were thinned on a Disa Electropol using AC-1 electrolyte.

Jan 1, 1968

By F. N. Rhines, T. E. Leonitis

The oxide scale that forms upon magnesium at elevated temperatures is non-protective in the sense that the rate of oxidation is constant and thus does not decrease with the growth of the scale as it does with other common metals. This generality was first stated by Pilling and Bedworth' and has been verified by Suzuki2 and by ScheiL3 Pilling and Bcdworth argued that the nonprotective characteristic could be predicted from the fact that magnesium oxide occupies less space than does the metal from which it springs, wherefore the scale is not expected to cover the metal so completely as to exclude all direct access to the atmosphere. Linear oxidation is thought by Scheil to be common to all cases where the reaction occurs at the oxide-metal interface. According to Suzuki," he product of high-temperature oxidation in the air is MgO contaminated with no more than traces of a nitride. When the metal is allowed to burn freely a fume composed of cubic crystals of Mg04 is given off. Delavaults observed that excrescences form upon liquid magnesium and alloys in thc course of oxidation. Beyond this it is known that the use of atmospheres containing small quantities of sulphur dioxide6 or carbon dioxide serve to retard the oxidation of solid magnesium and that beryllium' and calciums minimize the oxidation of molten magnesium exposed to the air. Many studies have been devoted to the nature and rates of "protective" oxidation, as exemplified by the cases of copper and iron, wherein the rate is characteristically parabolic. The theory of parabolic oxidation is well developed.~ Linear oxidation, on the other hand, has received but little attention and the theories proposed by Pilling and Bedworth and by Schcil have yet to withstand careful examination. There exists no comprehensive survey of the high-temperature oxidation of magnesium (or of any other metal that exhibits linear oxidation) over a broad range of temperature, under a variety of atmospheric conditions and covering a large group of alloys. It has been the purpose of the present investigation to provide such a survey, with the object of gaining a fuller understanding of linear oxidation, especially as applied to magnesium. Experimental Procedure and Results The experimental studies undertaken were of two kinds: (I) measurement of the rate of oxidation as influenced by the 6c

Jan 1, 1946

By T. E. Leonitis, F. N. Rhines

The oxide scale that forms upon magnesium at elevated temperatures is non-protective in the sense that the rate of oxidation is constant and thus does not decrease with the growth of the scale as it does with other common metals. This generality was first stated by Pilling and Bedworth' and has been verified by Suzuki2 and by ScheiL3 Pilling and Bcdworth argued that the nonprotective characteristic could be predicted from the fact that magnesium oxide occupies less space than does the metal from which it springs, wherefore the scale is not expected to cover the metal so completely as to exclude all direct access to the atmosphere. Linear oxidation is thought by Scheil to be common to all cases where the reaction occurs at the oxide-metal interface. According to Suzuki," he product of high-temperature oxidation in the air is MgO contaminated with no more than traces of a nitride. When the metal is allowed to burn freely a fume composed of cubic crystals of Mg04 is given off. Delavaults observed that excrescences form upon liquid magnesium and alloys in thc course of oxidation. Beyond this it is known that the use of atmospheres containing small quantities of sulphur dioxide6 or carbon dioxide serve to retard the oxidation of solid magnesium and that beryllium' and calciums minimize the oxidation of molten magnesium exposed to the air. Many studies have been devoted to the nature and rates of "protective" oxidation, as exemplified by the cases of copper and iron, wherein the rate is characteristically parabolic. The theory of parabolic oxidation is well developed.~ Linear oxidation, on the other hand, has received but little attention and the theories proposed by Pilling and Bedworth and by Schcil have yet to withstand careful examination. There exists no comprehensive survey of the high-temperature oxidation of magnesium (or of any other metal that exhibits linear oxidation) over a broad range of temperature, under a variety of atmospheric conditions and covering a large group of alloys. It has been the purpose of the present investigation to provide such a survey, with the object of gaining a fuller understanding of linear oxidation, especially as applied to magnesium. Experimental Procedure and Results The experimental studies undertaken were of two kinds: (I) measurement of the rate of oxidation as influenced by the 6c

Jan 1, 1946

By J. T. McGrath, R. C. A. Thurston

Poly crystalline specimens of copper, and copper with various additions of zinc, were tested in plane-bending fatigue. In tests performed at a constant stress, the fatigue life of copper increased slightly with the addition of up to fifteen per cent zinc. There was a sharp increase in fatigue life as further additions of zinc of up to 35 pct were made. Surface observations showed that the coarse slip bands that are characteristic of fatigue became narrower as the concentration of zinc increased. The rate of crack propagation also decreased with increasing zinc content. It is suggested that the fatigue behavior is controlled by cross slip processes. CROSS slip occurs when dislocations move from one primary slip plane to another along a connecting or cross slip plane. The primary and cross slip planes have a common slip direction. Wide stacking faults, having low energy, tend to make cross slip more difficult. According to recent theories, the ability of a material to cross slip is important to the formation and propagation of fatigue cracks. McEvily and Machlin2 have examined this concept experimentally by fatiguing single crys tals of lithium fluoride, sodium chloride, silver chloride, and KRS-5.* The latter two materials ex- hibit easy cross slip, while the former two do not. Normal rapid fatigue failure was obtained in the silver chloride and KRS-5 specimens, whereas it was much more difficult to achieve in sodium chloride and lithium fluoride crystals. Furthermore, numerous slip band extrusions and intrusions were found in silver chloride and KRS-5 crystals, whereas only one isolated extrusion was found in lithium fluoride and none was found in sodium chloride. McEvily and Machlin also consider that there is no clear-cut demarcation between crack initiation and propagation. The intrusion-extrusion process, which initiates crack formation, continues ahead of the cracks to allow propagation of these cracks along slip bands. The process of cross slip is therefore important not only to crack initiation, but also to crack propagation. Holden4 postulates that fatigue crack growth is dependent upon cross slip and thus upon stacking-fault energy. Using an X-ray microbeam technique, he found a cyclic subgrain structure in fatigued aluminum and a-iron. Holden suggests that micro-cracks develop in the densely-packed sub-boundaries ahead of the main crack front, and when sufficiently numerous join up to promote crack growth. The ease with which a subgrain structure could form would depend upon the ability of the dislocations to cross slip, and thus upon the stacking-fault energy. Hence in aluminum, which has a high stack-ing-fault energy and in which cross slip is easy, Holden found that the relative rate of fatigue crack propagation was considerably greater than in stainless steel, a low stacking-fault energy material. It has been shown by a number of investigators that the probability of forming deformation stacking faults in copper increases as zinc is added.5-7 Cross slip should, therefore, become more difficult as the zinc concentration is increased. In order to check the validity of the foregoing theories, it was decided to test copper and copper with various additions of zinc in plane bending fatigue, and determine to what extent their fatigue properties are dependent upon their ability to cross slip. EXPERIMENTAL PROCEDURE Fatigue tests were carried out on polycrystalline OFHC copper and various copper-zinc alloys with 5, 15, 20, 30, and 35 wt pct Zn. The Cu-Zn alloys were obtained commercially in sheet form. Test specimens, as shown in Fig. 1, were machined from sheet that had been reduced to an approximate grain size of 0.040 mm, the heat-treatment procedure being similar to that of Feltham anc copley.8

Jan 1, 1963

By D. R. Mash

A strong yield point with attendant enhanced mechanical properties was found in commercially pure beryllium under certain conditions of heat treatment. Beryllium specimens also responded to both quench and strain aging treatments. Based on these results, a possible means of obtaining increased normal temperature mechanical properties is suggested. COMMERCIALLY pure beryllium has been found to exhibit the yield point phenomenon and several other aging manifestations under certain conditions of heat treatment. This behavior is not surprising in view of the present accumulation of experience regarding such effects in numerous metals; but in addition to extending this experience to include beryllium, the present study is of interest because aging effects are generally associated with the presence of small amounts of solute elements. The well known lack of tensile ductility in beryllium at normal temperatures is also considered to be due to impurities in some way. In the present investigation, the view was taken that beryllium of commercial purity (greater than 98 pct) should be considered as a dilute alloy and that precipitation phenomena may well exist which could lead to enhanced mechanical properties. In connection with this possibility, published data on the variation of mechanical properties with temperature are of interest. For example, Fig. 1 illustrates the variation of ductility (percentage of elongation) and ultimate strength as a function of temperature for beryllium of various histories.* Although these curves are somewhat schematic in nature, they clearly indicate the possibility that precipitation of an unstable phase and/or aging effects occur during tests in the region 400" to 700°C. The existence of such behavior should be recognized as affecting the properties of the commercial material and perhaps can be employed advantageously. Experimental Method All testing was done at room temperature using a Baldwin universal testing machine. A microformer extensometer was used in conjunction with a micro-former-type stress-strain recorder. All tests were conducted at constant loading rate, the slowest rates being used. This corresponded to 120 lb per min in the 1200 lb full scale range and 300 lb per min in the 6000 lb full scale range. After the rate of loading was set in the elastic range of the material during the early part of the test, no further adjustments were made, allowing the test to proceed at that setting. In the plastic region of the curve above the yield region, strain rates of from 0.002 to 0.006 in. per min were regularly obtained. All experimentation was carried out on specimens machined from the same lot of beryllium, lot No. Y5036BP. Table I shows the chemical analysis as furnished by the supplier, Brush Beryllium Co., as well as the standard specifications to which commercial beryllium is produced. Both 1/4 in. thick hot pressed plate and ½ in. round hot pressed and warm extruded rods were obtained. The history of the material is reported to be as follows: 1—Beryllium metal plates, produced from a standard hot pressed QMV beryllium metal block 4x15x40 in., were cut off and finished machined to 1/4x6x12 in. flat plates. The original hot pressed block was made by hot pressing —200 mesh vacuum cast attri-tioned powder at about 1050°C under vacuum. 2—Beryllium rod was hot pressed and warm extruded. Extrusion billets were machined from the regular hot pressed blocks followed by extrusion at 425°C. The extrusion was done without jacketing, and graphite was used as a lubricant. The rods were then straightened at 720 °C, after which they were annealed at 800°C for 15 min. Both flat tensile specimens and round tensile specimens were tested. The former were machined from the plate stock into standard specimens according to specifications shown in ASTM E8-52T. The nominal cross-section was 0.25x0.500 in. and the gage length was 2 in. The round specimens were

Jan 1, 1956

By Gregory M. Dexter

Recent litigation in Pennsylvania between three coal-mining companies and a private water company resulted in the payment by the coal companies of the equivalent of about $500,000 to buy a new water supply to replace that which had been damaged by acid drainage from strip mining. An investigation of the relevant facts indicates that the water could have been treated by spending about $40,000 on equipment and $15,000 yearly for chemicals, labor, and power until the contarnination could be reduced about 80 pct. The water company's supply, furthermore, had deteriorated largely by reason of dry weather before stripping was begun by the coal companies. Payment to the water company should not have exceeded $300,000 and could have been as low as $100,000. Strip mining of coal is common in Pennsylvania. The most important objection to it in Pennsylvania is generally acid pollution of runoff water. An outline of the methods, therefore, that could be used to reduce such pollution, to compare acid-contaminated waters. and to treat such waters to make them satisfactory for public and industrial use is worth-while. The watershed of the West Penn Water Co. covers about 4.5 square miles, 20 miles west of Pittsburgh, and has two 90,000,000 gal reservoirs supplying about 1,300,000 gal daily for public and industrial use of which 450,000 gal daily are for two railroads. The pollution arises from weathered derivatives of typical'" Coal Measures"' rocks, the principal source being pyrite (and marcasite) in Pittsburgh and Rooster coals. Springs and seeps on hillsides issue from sandstone and limestone formations intersecting shale or clay land surfaces, or from perched water tables. The two reservoirs create an artificial permanent water table. Soap-hardness tests on three seepage samples taken in a dry summer ranged from 150 to 500 ppm. Water sampled came from aquifers above Pittsburgh and Rooster coals, obviating the possibility of contact with pyrite-containing coal. Since acid contamination of mine waters is the result of chemical reactions of oxygen and water with pyrite, it will be reduced by the exclusion of either air or water. The Sunnyhill Coal Co. has applied this principle in its "contouring" method of strip mining by burying contaminated coal-waste material under a compact, smoothed-up surface of top-soil, gravel, clay, and sand at a cost

Jan 1, 1950

By William Rawles

THIS report is the first of a series planned by The Mineral Inquiry, organized by the American Institute of Mining and Metallurgical Engineers to make factual studies of the world's mineral resources in their political and international relations. The efforts of The Inquiry are directed toward filling certain notable gaps in available information, without duplication of many other investigations touching this field which are being conducted by other organizations, public and private. Much of its work is indirect-suggesting topics for study by other individuals and organizations and aiding in their planning and correlation. The present report is designed to show the nationality of the commercial control of mineral resources, in addition to the geographic distribution of production by nation-in other words, the overlapping of political and commercial control. Detailed accuracy cannot be claimed for the figures presented. For some companies division of ownership by nationality has been very difficult to ascertain, as many companies are reluctant to dis-close the extent of their holdings in other corporations, and the impossi-bility of tracing all stock ownership is obvious. Also there are frequent changes in the distribution of stock control. The percentages given rep¬resent only the participation that has been identified definitely, even though it is known in some cases with fair certainty that larger interests exist, as, for instance, American participation in foreign chromite companies. In bringing together these figures we have had the cordial co-operation of the United States Bureau of Mines, the United States Geological Survey, the Mineral Division of the Bureau of Foreign and Domestic Commerce, the Brookings Institution, and of many specialists connected with the mineral industries covered. The report does not cover the entire list of minerals. Coal, although it is, one of the most important minerals, was omitted because not more than one or two per cent of the world's production comes from mines that are owned by companies foreign to the countries where the coal is produced. Others, such as gold, are omitted because sufficient data have not yet been accumulated. It is hoped that some of these may be covered in subsequent reports. It is not our purpose here to discuss the significance of the figures sub-mitted, but only to point out the general nature of the problems on which they have a bearing.

Jan 1, 1933

By L. V. Pirela, S. M. Farouq Ali

Some interest has been expressed recently in the application of solvents in conjunction with a thermal drive, such as a steamflood. At least one field project of this type has been reported. This paper makes the first attempt to provide some of the basic information necessary for choosing a solvent for such an application. Results of displacements conducted at elevated temperatures are also discussed. This paper shows that, in the case of alcohol-hydrocarbon-water or brine ternary systems, the system miscibility may increase, decrease, or both increase and decrease within the same system when the temperature increases. The distribution coefficient was consistently found to increase in favor of the oleic phase with an increase in temperature, which is advantageous from the standpoint of oil recovery. Results of solvent displacements in a sandstone core showed that even a relatively small temperature effect in the favorable direction (increase in miscibility and distribution coefficient) can lead to a 50 percent increase in oil recovery. On the other hand, if the system miscibility decreases with the temperature, even though the distribution coefficient increases, the oil recovery at the higher temperature may not increase. INTRODUCTION Miscible displacement has been the subject of many investigations. Miscible-phase solvent flooding, employing solvents such as alcohols that are miscible with both oil and water, has received considerable attention. Investigations conducted by Gatlin and Slobod,l Taber, Kamath and Reed,2 Holm and Csaszar,3 and Farouq Ali and Stah14 have helped in understanding the mechanism of solvent flooding. While the use of alcohols and similar solvents as oil recovery agents is economically unattractive, these solvents nevertheless provide a means of understanding the mechanistic aspects of important miscible-phase oil recovery processes such as the Maraflood process (discussed by Gogarty5). As shown by Taber et a1.,2 the phase behavior of a solvent-oil-water system is of .utmost importance in determining the efficiency of the oil displacement. This paper makes the first attempt to obtain the ternary phase behavior data for nine alcohol-hydrocarbon-water/brine systems at elevated temperatures. Results of core tests at elevated temperatures are also presented which corroborate the effect of temperature on oil recovery, as judged on the basis of phase-behavior data. The use of solvents at elevated temperatures has been suggested earlier by Farouq Ali.6 At least one field test of this type has been reportedO7 With the widespread use of thermal recovery techniques, it is possible in some situations (especially in steamflooding) that the use of a suitable solvent in conjunction with the heat carrier may be economically feasible. This paper attempts to provide some of the basic information needed for judging such feasibility. LOCATION OF THE PLAIT POINT The phase behavior of a typical ternary system consisting of a solvent, hydrocarbon and brine (or water) can be represented by a triangular diagram such as the one shown in Fig. 1 (for temperature TI). Point Pon the binodal curve represents the plait point, being the limit of tie lines such as Y1 Y2 The compositions of the coexisting oleic and aqueous phases are given by points Y2 and Y1, respectively, for any mixture composition along Y1Y2. The characteristics of ternary diagrams have been discussed by Findlay8 and others. Taber et aL3 have shown that the position of the plait point in a particular ternary system plays the decisive role in determining whether or not theoleic phase would be displaced in a continuous manner during an alcohol displacement. The area above the binodal curve also is important, since it represents

Jan 1, 1969