Search Documents

By J. H. Huang

In this investigation, the selective precipitation of cobalt and molybdenum from Co-Mo aqueous solutions was studied in order to recover efficiently valuable elements from industrial effluents generated from a novel electrodeposition of nanocrystalline Co-based alloys process and reduce the effluent impact on environment. It was found that the behavior of cobalt in aqueous solutions was substantially affected by the presence of molybdenum. When adding 11.6 to 46.6g/L molybdenum to a 50g/L cobalt solution, the co-precipitation of molybdenum and cobalt started to occur at pH value of 3-4. However, without the presence of molybdenum, cobalt could only be precipitated out of the solution at about pH 6. Most of the molybdenum was found in the solid phase when the solution pH reached 5. After further increasing pH to greater than 7, the molybdenum dissolved back into the solution. Cobalt kept precipitating as the pH increased. When the pH was greater than 7, most of the cobalt was present in the solid phase. The chemical and physical characteristics of the precipitated materials were investigated by SEM, XRD, AAS and EDX. It was revealed that the precipitate was initially present as cobalt molybdate oxide hydrate and subsequently transformed as sodium cobalt molybdenum oxide. With further increasing the solution pH, the precipitate was transformed into cobalt hydroxide. Further investigation implied that most of molybdenum was chemically tied to the precipitate produced at the low pH, yet at the same time, physically entrapped at the high pH. The paper also presents the influence of reaction temperature and time on the precipitation process and kinetics.

Jan 1, 2003

By Adam Powell, Soobhankar Pati

"Solid Oxide Membrane (SOM) Electrolysis is a new energy-efficient zero-emissions process for producing high-purity magnesium and high-purity oxygen directly from industrial-grade MgO. SOM Recycling combines SOM electrolysis with electrorefining, continuously and efficiently producing high-purity magnesium from low-purity partially oxidized scrap. In both processes, electrolysis and/or electrorefining take place in the crucible, where raw material is continuously fed into the molten salt electrolyte, producing magnesium vapor at the cathode and oxygen at the inert anode inside the SOM. This paper describes a three-dimensional multi-physics finite-element model of ionic current, fluid flow driven by argon bubbling and thermal buoyancy, and heat and mass transport in the crucible. The model predicts the effects of stirring on the anode boundary layer and its time scale of formation, and the effect of natural convection at the outer wall. MOxST has developed this model as a tool for scale-up design of these closely-related processes.IntroductionSolid Oxide Membrane (SOM) Electrolysis is a variation on the Hall-Héroult process for molten salt electrolysis of oxides which promises to solve many of the problems of its predecessors. Magnesium in particular is both soluble in molten salts and highly reactive, such that it migrates to the anode and reacts with the oxygen or C02 anode product, reducing current efficiency to as low as 10-20%. But a zirconia solid electrolyte between the molten salt and anode blocks this reaction, boosting current efficiency to at least 90%. Separating the anode from the molten salt also opens up anode material selection to liquid metals and SOFC cathode materials such as Lai.xSrxMn03 (LSM) and YCr03. And zirconia's selectivity makes the oxygen by-product very pure."

Jan 1, 2012

By R. Padilla, M. C. Ruiz

Arsenic, antimony and bismuth are commonly found in copper concentrates usually as the minerals enargite, stibnite and bismuthinite, respectively. Concentrates having high levels of arsenic and antimony must be pretreated before smelting. Roasting is the preferred method for removing these toxic impurities from concentrates; However, the removal of As, Sb and Bi in oxidizing roasting by volatilization may not be complete due to the slow reaction rates at 500- 700 °C. Oxidizing/volatilization data were obtained from pure mineral mixtures and from arsenic rich copper concentrate. The reaction mechanism for the volatilization of arsenic and antimony were discussed. Near 100% As and over 95% Sb volatilized in the oxidation of a mixture of pure minerals at 700 °C, 1% oxygen, while over 95% As, and 35% Sb volatilized at 600 °C in 1% oxygen atmosphere when using a copper concentrate containing 3.51% As, 0.14% Sb, and 0.01% Bi. Bismuth did not volatilize.

Jan 1, 2015

By H. Palkowski

Recent trends in the automotive industry lead to increasing interest in advanced high strength steels (AHSS). Those steels often have a high bake hardening potential (BH), giving additional contribution to the strength of structural parts, subjected to the paint baking process. For hot rolled AHSS, namely dual phase and martensitic steels, the effect of process conditions on mechanical properties had been investigated. However, the influence of chemical composition within the range in industrial production has not been investigated sufficiently yet. In the current research, samples with different chemical compositions within the characteristic interval for industrial production are under investigation under different preload conditions and simulating the thermo-mechanical production process. The samples were then subjected to BH process. Tensile tests were performed to study the influence of varying chemical composition on the BH effect. The results of investigations on dual phase steels will be presented in this paper.

Jan 1, 2008

By Na Wang, Chao Du, Yao Zhang Shuqiang Jiao, Hongmin Zhu

"Na2NbAlO5 was synthesized using Nb2O5 and NaAlO2 as raw materials in molten NaCl-CaCl2 by a solid reaction. With an addition of sodium into the melts, Na2NbAlO5 was subsequently reduced to form NbAl3 intermetallic compound with a particle size of 50-300nm.IntroductionThe intermetallic compounds of niobium aluminides have been a subject of research interests as high temperature materials because of their properties such as high melting temperature, large specific strength at elevated temperature, good resistance to high temperature oxidation, low density and large ductility [1,2]. They are applicable for turbine blades in aircraft engines and stationary gas turbines [3,4].In recent years, the methods of powder synthesis have been widely discussed. There are many methods to synthesis intermetallic compounds such as conventional melting and solidification [5], powder metallurgy [6,7], reaction sintering [8] and reaction sintering with prior mechanical activation [9,10]. There is a prominent weakness in such methods that they use metal to produce intermetallic compounds by the means of diffusion reaction. Although the metal can diffusion sufficiently, it is still hard to avoid maldistribution of the constituents which impairs the properties of the materials."

Jan 1, 2012

By P. Wieser, D. Feke

"Priming of filters with small pores is influenced by the surface tension of the liquid metal and may be complicated by freezing • Freezing followed by melting has been observed experimentally. This process has been modeled on the basis of one dimensional heat flow by radiation to the filter and by conduction in the metal. Also considered are super-heat of the metal and the initial filter temperature. The results of the model provide useful guidelines for the application of filters. IntroductionFiltration has been recognized as a valuable method of refining by removing suspended phases from liquid metals or alloys. Woven fiberglass type fabrics and wire screens were used initially in the aluminum industry. With the introduction of the ceramic filters that exhibit improved inertness and refractoryness, filtration has been introduced to higher melting alloys including cast irons, superalloys, stainless steels, as well as low and medium carbon low alloy steels. A considerable literature is delveloping rapidly on the progress in applications and the advances in understanding the mechanisms and effectiveness of filtration processes (1-8).With the use of filtration for different alloy systems for the production of cast to shape parts a bewildering variety of gating system modifications has been developed (Figure 1) to accommodate the installation of filters in the mold. The modifications have two principal purposes: 1) the runner expansion is intended to compensate for the resistance to flow due to the filter and that of the captured inclusions, and 2) the metal reservoir upstream of the filter, provides a temporary by-pass which permits metal to flow across the filter and heat it until priming can be accomplished. priming of.filters by low and medium carbon steel is readily accomplished but, compared to such alloys as cast iron or 19 Cr-9Ni stainless steel, requires greater precautions to avoid failure to prime by excessive freezing on or inside the filter pores. This problem is further examined below:"

Jan 1, 1986

By Feng Gao

A general unsteady- state model, based on a cracked substrate, has been developed to account for reaction and diffusion within porous substrate during oxidation of Carbon Fiber Reinforced Carbon matrix (CIC) composites. The effects of several parameters, such as diffusion and reaction rate ratio, oxygen concentration, and composite density, on oxidation process are explored. Also, theoretical results for a set of parameter values of the CIC composites are compared with experimental data. It shows that the model predicted values agreed well with the experimental data in weight loss. Based on this model, quantitative predictions of oxidation of a composite with cracked substrate can be made.

Jan 1, 1993

By Jose Luis Lopez Mendez

In May 1992, MEXICANA DE CANANEA, S.A. DE C.V. finalized the life of its Reverberatory Furnace which lasted 16 years. This created the need to prepare the Smelter for the next campaign.

Jan 1, 1994

By ChuanJie Cai, Zemin Zhuang, Jing Chen, Xuebin Hao, Shaobo Zheng

"Carbon which was used as heating and reducing agent in traditional iron and steel making process at present brought us large amounts of greenhouse gas harmful gases and dust seriously leading to the fog and haze condition. As one of ideal global new energies, Hydrogen has good features such as rich resource, high heat efficiency, cleanness, renewable and transportation. With the commercialization of hydrogen energy, the world energy structure will be changed greatly. Although many scholars have done a lot of researches and long-term exploration on hydrogen metallurgy, researches on the formation of metal iron phase in the process of hydrogen reduction of iron oxides in slag was rarely reported, which had important theoretical significance on the development of hydrogen smelting reduction process. Based on the thermodynamics and kinetics calculation, A laboratory experiment has been designed to research the iron phase formation during hydrogen reduction of iron oxides in the molten slag in this paper. SEM and EDS techniques were also used to observe and analyze the iron morphology. According to detection results, the influence of temperature, reaction time and surface tension on the morphology of the iron phase reduced were showed.IntroductionWith the increasingly severe global warming greenhouse effect, governments are paying more attention to no-carbon and low-carbon energy development and utilization. Hydrogen has received widespread attention around the world, which has rich resources, high thermal efficiency, large energy density, use clean, transportation, storage, renewable etc [1].The development of the hydrogen economy is new competition areas of the world economy for the 21st century. China should assess the situation, and achieve the important strategy of peaceful development as the realization of new industrialization, by establishing a ""hydrogen economy"" industry revolution which replaces fossil energy. The current hydrogen metallurgy process includes hydrogen direct reduction, smelting reduction and direct steelmaking process. Hydrogen plasma hydrogen metallurgy is the use of hydrogen as a reducing agent to replace carbon reductant, to reduce carbon dioxide emissions, and to ensure the sustainable development of ironmaking industry."

Jan 1, 2014

By Kang Wan, Lei Tang, Jianchao Li, Jieyu Zhang, Minqi Sheng, Jifang Xu

"The viscous flow phenomenon in slag close to the liquidus temperature was considered. A simple approach that liquidus temperatures of melt could be derived from viscosity data was employed. The potential of this method for estimating the liquidus temperatures of pure water and binary alloy was demonstrated. The liquidus temperatures of the CaO-Alz03 based slags obtained from the second derivative method depends upon the number of viscosity values available at different temperature intervals. The results indicated that plots start deviating from the straight-line behavior at temperature as expect, and the second derivatives show the break points at a certain temperature, which is the liquidus temperature. Comparisons among the present observations as well as the characteristic temperature of the selected slags, which measured by the hemisphere method and DSC, indicated that it is possible to get a reasonable idea of estimate the liquidus temperatures from activation energies for viscous flow.IntroductionThe liquidus temperature of slag, which has a significant effect on the kinetics of chemical reactions and the slag-metal separation, is extremely important for metallurgical operations. Experimental measurements of the liquidus temperatures of slags are difficult, since slags invariable supercool. In addition, behavior of a single constituent in a multi-component slag is different in different circumstances due to its interaction with other constituents. Hence, it is essential to study the liquidus temperature of each particular slag resulting from a special process. Usually, the compositions of the slags aimed to the single liquid region of the phase diagram. However, the phase diagram of many slag systems, which back often to the 1950's, involves considerable uncertainties. Many liquidus temperatures are given as dotted lines in Slag Atlas [1]. Disagreements between the phase diagram and the reality have been found [2]."

Jan 1, 2013

By Kazuhiro Asai

Nippon Mining and Metals Company has an annual indium production capacity of 30 tons at its Saganoseki smelter and refinery. Lately, indium content in the. zinc smelting dust, one of the main sources, has been on the decrease while the amount of impurity in it on the increase. The present process at Saganoseki does not permit efficient elimination of a large. amount of impurity. Therefore, studies were conducted to improve its recovery process. As a result, a new indium recovery process consisting of leaching, solvent extraction and electrowinning has been developed. The new process was tested at a pilot plant and satisfactory results were obtained. This new process is discussed in this paper.

Jan 1, 1995

By Takahiro Miki

Soldering material widely used is Sn-Pb alloy, which have low melting point and excellent electrical, strength properties and wettability. However, Pb is one of the toxic elements, which is undesirable due to environmental and safety reasons, thus Pb-free alternative alloy is preferred for new soldering material. Sn-Ag and Sn-Zn based alloys have been viewed as very promising candidates, among many potential substitutes. Addition of third element to these alloys will decrease melting point of the alloys. Hence, Sn-Ag-In and Sn-Zn-Mg alloys are expected to be suitable for replacing Sn-Pb solder alloy. In order to design new Pb-free soldering materials, it is crucial to understand precise thermodynamic properties and phase diagrams of alloy systems. In the present work, ion current ratios of Ag to In and Mg to Zn were measured for Sn-Ag-In and Sn-Zn-Mg alloys by mass spectrometry, respectively. Also, the authors reviewed the thermodynamic properties of terminal binary alloys determined by other researchers and evaluated a thermodynamic functions to express the excess Gibbs free energy of each binary alloy. Thermodynamic functions to express the excess Gibbs free energy of liquid Sn-Ag-In and Sn-Zn-Mg ternary alloys were determined, utilizing the assessed Gibbs free energy of terminal binary alloys with the measured ion current ratios using mass spectrometer.

Jan 1, 2003

By Zhou Jiemin

A mathematical model is developed to determine the economic thicknesses of refractories and insulations in rectangular furnaces, Both the heat loss cost and the lining investment are taken into account to achieve a minimum operation cost. For the sake of calculating the heat flux, the paper is particularly concerned with the simulation of the three-dimensional transient heat conduction processes in the lining and a Douglas-Rachford method is used to solve the finite difference equations, The model has been used to design an industrial electric resistance furnace operated periodically. the values of temperatures and power consumption measured from the furnace correspond with the model results.

Jan 1, 1991

By V. Ramachandran

Over the past 20 years, water treatment plants have been built at various Asarco facilities to effectively handle the process waste streams that need to be bled from the system. The current paper review the several operations with reference to (a) waste streams processed, (b) process chemistry, (c) discharge options and recovery of treated water, and (d) sludge disposal.

Jan 1, 1994

By Dengfu Chen, Huabiao Chen, Yunwei Huang, Mujun Long, Youguang Ma, Lintao Gui

In the current work, a three-dimensional model coupling turbulent flow, heat and solute transport was developed to investigate the solute transport and redistribution in the mold of slab continuous casting where the Reynolds number is very high and the molten steel flows strongly. The conservation equations of momentum, energy and species for a multicomponent system which includes solute element C, Si, Mn, P, S were solved with the commercial software ANSYS Fluent. The parameters used in the model are based on the actual continuous casting. The fluid flow, temperature distribution and solute elements distribution were analyzed. Results showed that negative segregation occurred near the strand surface, and the species concentration reached a peak value at the solidification front during solidification. The segregation degree of solute element S is higher than the other solute elements because of its lower equilibrium partition coefficient. The species concentration in the liquid pool is homogeneous because of the turbulent flow effect.

Jan 1, 2015

By Aïda Espinola

This work is part of a research program concerning the study of heavy metal removal and selective recovery from electroplating waste waters in the Guanabara Bay ecosystem, preventing the potential noxious retarded effect of landfill, specially in a country of heavy rainfall. A flow-throw cell was employed to adapt to the limits established by the local legislation for disposal in rivers and seas. The cell design is presented and preliminary results show that this cell may be applicable for the decontamination from copper.

Jan 1, 1994

By Susumu Okabe

Top blow injection has been applied to continuous copper smelting and converting by Mitsubishi Materials Corporation since 1974. In this process, injected feeds are captured by and dispersed in the molten bath immediately and effectively, and the reaction is enhanced by the agitation of the bath. The continuous motion of the molten bath, however, may cause severe damage of furnace lining materials, if the injection is not controlled and the furnace is not designed properly. In order to suppress refractory wear, especially at the bath line, surface wave of the molten bath should be moderated. A cold model study was carried out with water bath in a cylindrical vessel and the physical model was derived which correlates the oscillation of gas jet impingement on the bath surface and the surface wave. It was found that a half of the proper frequency of the gas jet impingement coincides the proper frequency of the surface wave.

Jan 1, 1998

By Huanmei Yuan, Yuanyuan Wang, Hao Bai

Composite phase change materials are widely used in energy-saving and energy efficient process. Nano-encapsulated phase change materials are especially significant for making advanced working fluid applicable to waste heat recovery or storage. In this study, silica-coated stearic acid (SA) Nano composite phase change materials were prepared from tetraethyl orthosilicate (TEOS) and stearic acid (SA) via sol-gel process. The materials were investigated by Field emission scanning electron microscopy (FE-SEM), Transmission electron microscope (TEM), Fourier transform infrared spectroscopy(FT-IR) and Differential scanning calorimeter (DSC).The FE-SEM and TEM results show that monodisperse microspheres with stable core– shell structure were formed and SA was encapsulated in the silicon dioxide shell. The FT-IR results show that there were no chemical reaction between silicon dioxide and SA, which is the chemical property of the composite material, is stable. The DSC results show that the composite phase change material has favorable heat capacity.

Jan 1, 2016

By G. A. Brooks

Reactive ball milling has been proposed as a new route for producing carbides from oxides through carbothcrmic reduction. It is claimed that through milling oxide and graphite powders to the nanoscale, amorphous materials with very high reactivity are formed, that allows for easy transformation of the starting material to another in a subsequent thermal process. Thermodynamic analysis of this proposed process suggests that unless particle sizes are reduced to below 10nm, then reduction in size alone cannot explain a change in the stability of oxides. Even with nanometer scale powders, the products formed need to have a lower total surface energy than the reactants before a chemical change will occur. A model developed by Bhattacharya and Arzt for predicting localized temperature changes based on milling conditions suggest that temperarure rises less than 400 K will be achieved in laboratory conditions. The present calculations suggest that nanometer scale powders formed through high speed ball milling (>10 mls) may have undergone a process analogous to melting and quenching. Further work is required to fully distinguish these features.

Jan 1, 2003

By K. Iwami, K. Abe

"Onahama Smelter and Refinery has been operated-since 1965 arid currently produces 243,000 metric tons per year of cathode copper. The Onahama tankhouse consists of conventional-type No.1 and 2 tankhouses with the capacity of 123,000 metric tons per year and No.3 tankhouse with 120,000 metric tons per year, adopting jumbo tank system, using hazelett anode respectively.In October, 1996, for the purpose of improving the - anode verticality, new anode copper body press machine has been installed in No.1, 2 tankhouses; by increasing Walker type anode copper weight by 35kg to 365kg. Consequently, it is possible to raise current density from 191 to 222 A/m2 and the No.1 and 2 tankhouses capacity was increased by 15,000 metric tons per year to 138,000 metric tons per year.At present, the refining capacity is 258,000 metric tons per year in total including No.3 tankhouse.This figure is the largest one in Japan.IntroductionSince the Onaham tankhouse was put into operation in 1965, the cathode copper production has increase with much labor cost saving.The following two cases to increase Walker type anode copper weight by 35kg to 365kg were studied.a) To increase the cathode copper production by raising current density.b) To save the labor cost by prolonging the anode cycle in order to decrease the exchanging time of electrodes.So the electrolytic tests were carried out to confirm· the effect of current efficiency, cathode copper quality and working conditions for space adjustment.As a result, we concluded that it was indispensable to introduce the anode body press machine to keep usual current efficiency and cathode copper quality with same workers, and to be possible to increase cathode copper production.In addition, the high-speed press machine was needed to maintain same working time and which specifications were decided through various investigations. In October 1996, the new anode body press machine made by Kawazoe Machine Works, Ltd. has been installed in No.1 tankhouse."

Jan 1, 2000