Search Documents

By Yi Tan, Kazuki Morita, Yaqiong Li

Molten Si-Al alloy, with the addition of Sn, was used for metallurgical grade Si purification by a low-temperature solidification method, with the aim of improving the recovery rate of Si. In this ternary melt, bulk Si was grown with a planar front by a directional solidification process under a well-controlled thermal gradient and growth rate conditions, thereby reducing the contamination of solvent metals. Effects of cooling rate, amount of Sn addition, and temperature gradient on the quality of bulk Si were determined. The criterion for constitutional supercooling for single-phase growth from multicomponent melts was employed to evaluate the growth process.

Jan 1, 2015

By Fiseha Tesfaye, Pekka Taskinen, Daniel Lindberg

Due to increasing complexities of raw materials for base metals production the conventional pyrometallurgical processes are challenged. To make the appropriate modifications, thorough evaluations of the thermal stabilities of phases and phase assemblages which are commonly encountered in these processes are essential. In this work, phase relations and thermal stabilities of equilibrium phases in the Cu-Ni-S system have been reviewed. The calculated phase diagram of Cu-Ni system has been validated. At T < 630 K, in the Ni-rich corner, large scatter in data has been observed and discussed in detail. The other binary systems, Cu-S and Ni-S, have been also critically reviewed together with the ternary Cu-Ni-S system. The reviews were focused on compiling and discussing phase relations and thermal stabilities of the selected systems in the pyrometallurgical processes of Cu and Ni productions.

Jan 1, 2016

By V. Yahorava

Mintek has developed a non-destructive Resin-in-Leach method for the recovery of Rare Earth Elements (REE) from phosphogypsum (PG) waste dumps. However, PG from different sources was found to be highly variable in terms of REE recovery and physical properties. Development of a pre-treatment process was initiated to improve the robustness of the current REE recovery process in order to render it effective for any type of PG. Extensive research into the mineralogy of REE associations with PG revealed that the majority of REE are trapped inside phosphogypsum clusters which inhibits their recovery. Hydrothermal treatment of PG-containing slurry was found to result in re-crystallisation of gypsum with the release of REE phases encapsulated in it. This process was tested on various PG samples and subsequent REE recoveries improved from 5 to 80%. This approach carries a large potential for unlocking value associated with gypsum dumps worldwide.

By Gabriel Zarate

Mantoverde is a heap leach-SX-EW plant that was commissioned in December 1995 at a production rate of 42,130 tonnes of copper per year and 5.4 million tonnes of ore per year. Copper production was steadily increased reaching a maximum of 62,239 tonnes in 2012 for an ore throughput of 10,5 million tonnes. In order to get these production and throughput rates, a number of changes have been made in the metallurgical parameters of the plant operation since the start up, among them particle size, heap height, acid addition distribution in curing and leaching solution, leach cycles and pad type. Most of the modifications have been implemented after carrying out extensive column test work programs. The modifications implemented and the results obtained, as well as the test work programs carried out, are discussed in this paper.

By De-wen He

The distribution of persistent organic pollutants in the environment is studied using the multimedia environmental fugacity model, and environmental health risk assessment of POPs nearby a copper smelt enterprise is carried out. The result indicates that all are in an agreeable risk level without exception. The annual individual chronic risk index of HCB is 7.50×10-11. The annual individual risk index of 3,3&apos;,4,4&apos;-TCB is 1.57×10-9, and the annual individual risk index of 2,3,7,8-TCDD is 6.57×10-9.

Jan 1, 2009

By Sui Xue

A process has been developed from laboratory-scale experiments for the aqueous processing of various lead-bearing wastes. The process exploits the limited solubility of lead in sulfate-rich solutions to effectively separate lead from other metals. The lead sulfate is then completely converted to lead carbonate using sodium carbonate and ammonium carbonate. The effectiveness of this conversion was observed to be sensitive to the solution pH and carbonate concentration. The final stage of the process uses low temperature calcination of the lead carbonate to form PbO. Yellow lead oxide (massicot) is readily formed if calcination is conducted at a temperature at or iibove 50G°C, wlule red iead oxide (iitharge) is formed at temperatures near 450°?C. A complete economical analysis of the process will be discussed.

Jan 1, 1996

By I. Gaballah

The kinetics of oxychlorination of pure CI-2O3 with C12+02 gas mixtures is studied by ThermoGravimetric Analysis (TGA) in non and isothermal conditions up to 1000 °C. The reaction of Cr2O3 with C12+O2 chlorination gas mixtures starts at about 550 °C and the reaction product is CrO2Cl2. The oxychlorination rate of Cr2O3 is almost proportional to the chlorine partial pressure and to the fourth root of the oxygen partial pressure in the chlorinating gas mixtures. At 800 °C, the maximum chlorination rate is obtained using a gas mixture having a C12/O2 ratio equal to 4. The apparent activation energy of the oxychlorination reaction of Cr2O3 is 87 and 46 kJ/mol at temperatures lower and higher than 650 °C, respectively. By varying the chlorine and the oxygen partial pressures of the oxychlorinating gas mixtures at temperatures higher than 550 °C, it is possible to extract selectively the chromium chlorinated compounds from the chromium bearing materials. a. Laboratoire Environnemem et Minéralurgie, BP 40, 54501 Vandceuvre, France, b. École Nationale Supérieure de Géologie, Rue du Doyen Marcel Rouhault, 54501 Vandoeuvre Cedex, France, c. Centre National de la Recherche Scientifique, 3 rue Michel - Ange, 75794 Paris Cedex, France, d. Insritut National Polytechnigne do Lorraine, Rue de la Font de Haye. 54501 Vandceuvre Cedex, France.

Jan 1, 1997

By Sue Ritz

Gold extraction has relied on coconut carbon in adsorption circuits for several decades. IXOS®, invented by 6th Wave Innovations of Salt Lake City, Utah, is a new type of adsorbent that exceeds the selectivity of carbon and improves on the mechanical properties of other available resins. IXOS selectivity against copper cyanide complexes allows it to be used in circuits that currently struggle with copper contamination. IXOS potential to eliminate or reduce the application of SART technology will expand the opportunities to exploit more complex precious metals deposits. This paper will describe the technology behind IXOS molecular imprint, its comparison to carbon adsorption in the field, and the effect of efficiency on long-term recovery from heap leach METSIM simulation software.

By J. E. Dutrizac

A mineralogical study of a weak acid leach residue from the Clarksville zinc plant of Savage Zinc Inc. was carried out. The study focused on Pb and Cd as these elements most significantly impact on the environmentally acceptable disposal of the residue. The residue consists of major amounts of bassanite, zinc ferrite and various Zn-Pb-Fe-Cd silicate species. Also present are lesser quantities of PbSO4, sphalerite, Fe2O3 quartz, Mn-Pb-Fe oxides, SrS04, (Pb,Sr)SO4 iron gel-silica gel, jarosite and Ti oxide. The principal Cd carriers are the zinc ferrite, which contains up to 9.00% Cd and likely accounts for -45% of the total Cd content of the residue, and the various silicate species which contain up to 6.97% Cd and account for about 45 % of the total Cd. The sphalerite is a minor Cd carrier containing an average of 0.35 % Cd and accounting for -5 % of the total Cd; the other carriers contribute only trace amounts to the total Cd content. The major Pb carriers are PbS04, Pb-bearing silicates and Mn-Pb-Fe oxides. Minor proportions of the total 1.09% Pb content of the residue are carried by SrS04 and (pb,Sr)S04&apos; Trace Ph carriers include the iron gel-silica gel, Fe-Zn-AI oxide and bassanite. The residue after the toxicity characteristic leaching procedure (TCLP) is mineralogically very similar to the initial weak acid leach residue; the amounts of calcium sulphate are approximately the same in the two products. The principal Cd and Pb carriers are also the same as those noted in the initial residue, except that some dissolution and reprecipitation of Pb-Sr sulphate takes place. That the residue fails the TCLP test is likely a consequence of the superficial dissolution of Pb and Cd from species such as PbS04 or Zn-Pb-Fe-Cd silicate.

Jan 1, 1995

By Glenn C. Miller

Cyanide is the most common lixiviant for extraction of precious metals, and its efficient use in open pit mines has contributed to the increase in world production of gold during the previous two decades. With this expansion of precious metals mining using cyanide, public concerns have developed in response to the inherent public perception of cyanide as a tox-in as well as a series of environmental problems that are directly or indirectly related to cyanide use in open pit mining. Some of these have technical or regulatory solutions, while others will require additional investigation before they can be resolved. The following discussion will summarize some of the public concerns regarding the use of cyanide in precious metals mining. The issue of cyanide use in large scale precious mining is controversial, and recent banning of cyanide use in open pit mines in Montana, or complete banning of cyanide in Hungary has reflected those international concerns. The underlying basis for some of the bans (e.g. Montana) reflect a general concern of the environmental impacts of mining, rather than specific issues related to risk of cyanide use. The human safety record for cyanide use, particularly in the developed countries is good, and cyanide is clearly the most efficient lixiviant for precious metals. Indeed, the relatively short lifetime for cyanide in the environment renders it one of the less problematic chemicals used for extraction of gold from ore. Mercury amalgamation or use of bromide as a lixiviant are certainly much more problematic. What, then, is the basis f~r the international concern about precious metals mines that use cyanide. Ifuse of cyanide for gold recovery is to continue, what additional infom1ation needs to be developed that will allow a better management of the risks of cyanide? Which of the concerns are directly related to cyanide, and which are indirect concerns that more related to effects of open pit mining. Under what conditions should use of cyanide be discouraged? DUl::ing June of 2000 the United Nations Environmental Program conducted a two-day workshop on cyanide use in mining that was attended by persons from the mining industry, regulators and environmental community. Support and attendance at this workshop reflected concerns by all three groups on further restrictions for cyanide use and the emerging potential for guidelines for better management of the catastrophic release of cyanide-containing mining waste. The following discussion is meant to focus-on those risks and explore the basis for an often negative reaction to precious metals mining using cyanide. It is presented in the format of a statement, followed by a discussion. While admittedly provocative, the statements are meant to express the concerns? of the public regarding cyanide and the mining industry.

Jan 1, 1998

By V. E. Antonov

Hydrides of iron and iron-based alloys are thermodynamically stable only at hydrogen pressures in the gigapascal range and rapidly loose hydrogen under ambient conditions. At low temperatures, however, these hydrides can be retained in a metastable state at atmospheric pressure after being cooled under the high pressure to liquid nitrogen temperature. This review will discuss the current state of studies on phase transformations in the Fe-H and related systems and also on the composition, crystal structure and physical properties of the hydrides, both under high hydrogen pressures and in the "quenched" metastable state at ambient pressure. The studies at ambient pressure include magnetization measurements, X-ray and neutron diffraction, Mossbauer spectroscopy and inelastic neutron scattering. In the sections on Mossbauer and structural investigations of hydrides of Fe-Cr and Ni-Fe alloys new experimental results will be presented.

Jan 1, 2002

By Hong Yong Sohn, Miguel Olivas-Martinez

"Different approaches are used for calculating the ‘energy requirement’ of a process. The determination of energy requirement becomes confusing for a process in which a fuel is also a reactant. The key issue is which heat of chemical reaction should be included in the ‘energy requirement’ value. We will use the example of ironmaking processes to illustrate the problem. The different approaches essentially boil down to the question: does one include the combustion heat of the reductant used in the reduction reaction or just the heat of the reduction reaction? Depending on the viewpoint, either approach can be accepted; it is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of a process depends on the choice. The energy requirement of a novel flash ironmaking process will be compared with that of an average blast furnace operation.IntroductionDifferent approaches are used for performing energy balance calculations and perhaps more significantly in presenting the ‘energy requirement’ of a process. The question becomes more involved for a process in which one or more reactants are also used to generate the process heat by combustion. Often the key issue is which heat of chemical reaction to include in presenting the ‘energy requirement’ of the process.It is worthwhile to note at the outset that the difference in energy requirements between different processes for converting similar raw materials to the same desired product is largely unaffected by the choice of chemical reactions to be included. However, the absolute value presented as the ‘energy requirement’ of a process can be different by a large amount depending on the approach. We use the example of ironmaking processes to illustrate the problem. In these processes, as currently practiced or under development, carbon and/or hydrocarbons (including hydrogen) are used as the fuel as well as the reactant for reducing the iron oxide mineral.The different approaches in this case essentially boil down to the following question: does one include the combustion heat of the reductant used in the reduction reaction or treat the reductant portion as just a reactant? Depending on the viewpoint, either approach can be considered acceptable. It is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of an ironmaking process (e.g., the currently dominant blast furnace process) depends on such a choice. It is particularly important to clearly state the specific approach used when the energy requirement of ironmaking is compared with those of other industrial processes such as petrochemicals production."

Jan 1, 2014

By Daguang Lu

The section of sintering and BF (blast furnace) is very important in iron-making process. In practice, the scheduling is so extensive that three faults unfavorable to continuous product will be easier to happen. This paper introduces the integration Petri Net and GA (genetic algorithm) as suitable tools for simulation and optimization of scheduling to section of sintering- BF under a certain hot iron or-der. The situation of the iron plant Chongqing Iron and Steel Company is researched in approach above mentioned. By analysis, the conclusion is drawn that scheduling with optimized values can maintain continuity of key operations , can satisfy order of hot iron in maximal degree and can keep the best stability of key storages.

Jan 1, 2009

By P. N. Anyalebechi

"The effects of solidification rate, initial melt hydrogen concentration, and grain refining on porosity formation in aluminum alloy 2024 have been investigated with unidirectionally cooled laboratory-size ingots. The ingots were prepared from melts containing hydrogen concentration of 0.059-0.27 cm3/100 g and solidified at 0.2-37 °C/s. As expected, the amount of porosity, average pore size, and pore number density increased with increase in melt hydrogen concentration and decrease in solidification rate. However, the effect of solidification rate was greater at the very low melt hydrogen concentration (0.059 cm3/100 g). These results are consistent with reported effects of solidification rate and melt hydrogen content on porosity formation in other aluminum alloys. Interestingly, addition of grain refiner slightly increased the amount of porosity and the average pore size, especially at solidification rates above 1°C/s. IntroductionIn shaped castings and wrought products fabricated from ingots, billets, bars, or slabs of aluminum and its alloys porosity formation is a problem. This is because it compromises their tensile strength, fracture toughness, and fatigue properties [ 1-18]. The pores are usually the crack initiation and propagation sites [6,8,9] and the largest pores tend to dictate the fatigue life of the aluminum products [9,10,14]. Porous regions within an aluminum product probably yield first due to the reduced tensile load bearing capacity, causing the concentration of the strain near the voids which subsequently results in premature fracture. In aluminum alloy ingots, billets, bars and slabs porosity formation is particularly problematic because of its persistence through fabrication and potential for reappearance or exacerbation during subsequent thermal treatment processes before and/or after fabrication [19]. In fact, persistence of microporosity is a serious problem in large thick plates of wrought aluminum alloy products that must be rolled from correspondingly large direct-chill or electromagnetic cast ingots. Some of these thick plate products are machined into large aircraft components that are required in service to withstand multi-directional stresses and to possess high fatigue strength, fracture toughness, resistance to stress corrosion cracking, and strength in the short-transverse direction [1,20]."

Jan 1, 2011

By Boxun Lu, Juan Wei, Kun Chen, Wanlin Wang, Lejun Zhou

"Slag system is an indispensable part during the continuous casting process, and playing various important roles like absorbing inclusions, modifying heat transfer rate, preventing oxidation of molten steel, etc. to ensure the smooth process and excellent slab quality. However most slags contains more than 8% fluorides which tend to introduce a series of environmental and health problems. This study involves the research of the removal of fluorine through the chemical composition optimization. Through the studies of CCT, DHTT, XRD and SEM, it has been successfully founded that the crystalline phase of Ca11Si4B2O22 discovered in this study shows very similar crystallization property as Cuspidine (Ca4Si2O7F2), which is the most important crystalline phase in the current fluorine bearing slags. Moreover, the optimized free/low fluorine slag shows the opportunity to replace conventional high-fluorine mold slag for casting medium carbon steels that is regarded as the bottleneck of green slag development for continuous casting.IntroductionMold flux has been widely used in continuous casting to control heat transfer, lubricate the strand, absorb inclusions, provide insulation and prevent oxidation of the molten steel[1-3]. It usually contains fluorides, like CaF2, NaF etc., which are used to control the viscosity and solidification temperature of mold fluxes [4-5]. However, the presence of fluoride leads to corrosion of equipment, serious environmental pollution (toxic volatiles and water pollution), and high processing cost of cooling water[6-7]. Therefore, the study of low or free fluorine mold flux is of interest and attracts worldwide attention.S. Y. Choi et al. [4] used B2O3 as a substitute for cuspidine in steel B2PB2) however, B2O3 content was extremely high (up to 30 w%). Other studies have investigated F-free mold flux by adding or optimizing components as MgO, Li2O, B2O3 et al[8-11]. However, most of these focused on the melting and viscosity issues or for low or ultra-low carbon steels, where crystallization tendency is not significantly strong. Very few studies regarding to the development of low/free Fluorine mold flux for casting medium carbon (MC) steels have been conducted, due to the difficulty of the crystallization and heat transfer control without the formation of cuspidine."

Jan 1, 2014

By Neng-Wen Yu, Miao Wang, Ji-He Wei

The mass transfer characteristic between powder particles and liquid steel in the RH-PTB (Powder Top Blowing) refining has been investigated in a water model of 1/5 scale for a 90t RH degasser. The sodium chloride powder with analytical purity has been used as the flux for blowing. The mass transfer coefficient of the liquid side has been determined under the conditions of RH-PTB process. The influences of the main technological and structural parameters on the mass transfer rate have been examined. The results indicated that under the conditions of the present work, the mass transfer coefficient on the liquid side increases with raising the lifting gas blowing rate, inner diameter of the up-snorkel, circulation rate of the liquid and particle size of powder flux. And it decreases with an increase in the inner diameter of the down-snorkel. It is in the range of (l.36-7.30) x 10·4 mis, the appropriate dimensionless relationships have been obtained as follows:

Jan 1, 2000

By J. Wong

We report a successful use of x-ray absorption spectroscopy to probe the chemical and structural environment of trace elements in coal. When applied to vanadium in coal, it was found that vanadium exists in at least two environments: a trivalent site 6-fold coordinated by oxygens at ca. 2.0~ and a tetravalent site 5-or 6-fold coordinated also by oxygens, one of which forms a short V=O bond at ca. 1.6a. No evidence of nitrogen (porphyrin)1&apos;or sulfide environment was found. It was also found that the vanadium environ-ments in the raw coal did not survive unchanged in a liquefaction process. These findings have implications for coal cleaning processes and for trace element release into liquefaction process streams.

Jan 1, 1982

By F. Patisson

During exothermic gas-solid reactions, heat generation makes temperature rise and modifies the rate of the various mass transfer processes, namely the chemical reaction itself, the pore diffusion and the external transfer. We have investigated this thermal effect during the oxidation of zinc sulfide porous pellets in a thermo balance furnace, between 550 and 900°C-and under O2-N2 atmosphere. The results have been&apos; analyzed by using, firstly, the law of additive reaction times derived from the isothermal Grainy Pellet Model, and, secondly, a new numerical model taking into account non-isothermal conditions. Both the models can satisfactorily simulate conversion versus time, but the numerical model also depicts the temperature evolution within the pellet. Finally it is shown that owing to the heat generation the zinc sulfide oxidation takes place under diffusion control (3/4 internal, 114 external) in all the cases studied. During the course of reaction, the. pellet undergoes strong temperature variations, with thermal gradients confined to a shell oxide layer.

Jan 1, 1996

By Fei Ruan, Chang Jie, Jieyu Zhang, Jifang Xu, Kuochih Chou

"Viscosity is an important physical parameter of slag in metallurgical processes. Most studies of aluminosilicate and aluminate systems assume that aluminum occurs in tetrahedral coordination. In this case, the O/Al value was utilized to describe the slag structure in terms of the network character of aluminosilicate and aluminate systems. Composition and viscosity data from the literature and the trends were analyzed according to the O/Al value and temperature. It is shown that the O/Al value explains the trends in more than ten systems, containing more than 200 data points. In aluminosilicate system, the trend that viscosity value changed with the O/Al value which implies that alumina works as network modifier such as basic oxides or works as network former. In aluminate system, irrespective of the system and temperature, viscosity decreased steadily when O/Al value increased.IntroductionMetallurgical slags, which are made of oxides and many also contain fluorides, play an important role in metallurgical processes such as iron making, steel making and secondary refining processes. Aluminosilicate slags are applied in a wide range in metallurgical processes. A polymerizing effect of the addition of aluminum and an association of aluminum with low-field strength cations is further supported by the physical variations in aluminosilicate and aluminate systems. The behavior of alumina in silicate melts has been studied by various authors [1-6]. It is generally accepted that Al2O3 is amphoteric [7] because Al3+ ions can behave in profoundly different ways in a silicate melt. When added to a pure silica melt, Al2O3 acted as a network modifier, breaking the bridging oxygen of the pure silica network, thereby decreasing the viscosity in a similar manner to other network modifiers, such as CaO, MgO etc. to form [1/2Ca (AlO4)]4- complexes. However, when added with alkali or alkali-earth metal oxides, some of the Al3+ ions assumed tetrahedral coordination and replaced Si in the liquid network, the missing charge was compensated by Me+ or Me2+ ions. Therefore Al2O3 acted as network former [8, 9]."

Jan 1, 2011

By S. Raghavan

The thermodynamic activities of MgO in the solid solutions that can exist in the system NiO-Mg0-Zn0 are determined by measuring the EMF of the cell: O2 (g), Pt / MgO, MgF2 // MgF2 // x MgO + yNiO + (1-x-y)ZnO / Pt, O2 (g) / MgF2 in the temperature range 1190-1237 K. Equilibrium phases were prepared along the quasi- binary lines MgO/NiO = 0.1765,0.3333, 1.0,3.0 and 5.667 with the ZnO contents being 0.1, 0.2, 0.25, 0.35, 0.5, 0.75 and 0.9. The crystal structures of the phases were identified by X-ray diffraction. Results obtained so far show that a single phase MgO-rich cubic solid solution exists upto 0.2 ZnO content and for compositions above 0.25 ZnO, a second ZnO rich wurtzite phase forms in addition. Activity measurements show that for low MgO and ZnO contents, the MgO activities exhibit ideal to slight positive deviation from ideality and at higher MgO contents, a negative deviation is shown. Further studies are in progress.

Jan 1, 1993