Search Documents

By L. A. Puchkov

The creation of automatic methane concentration control systems presupposes the use, as a control factor, of the air rates in workings and in mine as a whole. These systems present a complicated set of computers and software, including as major components the following - systems for detecting methane concentration and air rate; - telemechanics systems; - programs and means of data processing; - programs and means of air rate control in workings and main fan capacity control. The paper analyses the experience of development and exploitation of automatic methane control system in gassy mines of the USSR Donetz coal basin. Much attention is given to the study of technological factors influence upon aerogasdynamic process using automatic methane control system.

Jan 1, 1989

By Paul D. Kovscek, Charles D. Taylor, Edward D. Thimons

When blowing ventilation is used on a mining section, a machine-mounted scrubber is often required to maintain face dust levels below 2 mg/m3. Operation of the scrubber also affects airflow patterns at the face and the dilution of liberated methane. Reductions in scrubber flow can result in increased methane concentrations. During mining, loading of the scrubber filter with dust is likely to reduce airflow. Detecting changes in scrubber flow is difficult, especially with extended cutting, because the machine must be operated from a remote location. Tests were conducted to demonstrate how scrubber airflow could be continuously monitored at a remote location. Three variables, static pressure at the fan inlet, differential pressure across the scrubber filter, and scrubber fan motor current, were continuously monitored while the scrubber filter was incrementally loaded to reduce air flow. The results show that monitoring each variable provided a way for estimating scrubber flow.

Jan 1, 1995

By Richard E. Steffens

The underground portion of Duke Power Company's Bad Creek Pumped Storage Project in northwestern South Carolina consists of a powerhouse cavern (132 m. long, 23 m. wide, 50 m. high), 407 meters of shafts and approximately 3615 meters of tunnel, both lined and unlined, with diameters varying from 4.2 meters to 9.0 meters. A case history is presented, including the early pilot tunnel exploratory work and how this affected design, the design of the project, and the excavation, rock support and tunnel lining work. Problems and experiences encountered during the construction are given. The effects of high horizontal insitu stresses in the granitic gneiss are discussed along with solution taken.

Jan 1, 1989

By Shoung Ouyang, Pinnaduwa H. S. W. Kulatilake

Available literature on the topic is reviewed. Methods are suggested to improve the presently available techniques to perform probabilistic modeling of shear strength parameters for rock discontinuities. The Mohr-Coulomb model and a power law model are used as strength criteria to model shear strength of rock discontinuities. Use of various regression techniques for point estimation of shear strength parameters from direct shear data are discussed. Goodness-of-fit tests for bivariate beta and bivariate normal distributions are developed, and the applicability of them to represent the distribution of shear strength parameters is tested through examples. Both distributions seem to have potential to represent the statistical distribution of strength parameters.

Jan 1, 1986

By Barada K. Mishra

The potential merit of the discrete element method (DEM) as a numerical tool for analyzing process engineering problems involving particulate material is discussed. In this method, the dynamic equilibrium equations for each distinct and deformable body are solved. Therefore, it readily lends itself to modeling large numbers of discrete, interacting bodies as in mineral processing operations where a charge of particulate material is processed. Here some applications of DEM are reported: motion of particles in the ball mill, mixer, and jig. Although DEM has made very little headway in mineral processing research, it is shown here that a host of other areas of industrial interest in the context of flow of particulate materials can also be made amenable to analysis by this method.

Jan 1, 1993

By R. L. Grayson

Conventional mine safety wisdom states that "the most efficient mines are also the safest." Since the 1980s, small mines (and contractors) have been targeted as the most dangerous because of their fatality records. However, statistical analysis of West Virginia safety and production data from 1993 indicated that, when considering the correlation between accident severity and tons mined per employee-hour worked, the most efficient mines were, with the exception of very small mines, not the safest operations. This paper presents the results of an extended analysis of West Virginia mine safety using 1993 and 1996 data and concludes with the method used to suggest current priorities for focusing interventions.

Jan 1, 2000

By I. S. Parrish

Gold deposits in Hebei and Shanxi provinces in northeast China fall into three general classes: - Placer deposits - Mesothermal vein deposits - Disseminated and oxidized volcanogenic deposits Past production dating back thousands of years has all but exhausted the placers. The mesothermal vein deposits, incorrectly considered in the past as "greenstone" type, are small to moderate in both size and grade. Production from these granulite and amphibolite hosted veins, at present greater than from the newly discovered disseminated deposits, is expected to wane. Production from the disseminated deposits achieved only in the past few years is expected to equal or surpass that from the other classes of deposits. At least one "world-class" deposit is being developed.

Jan 1, 1989

By Jerry Peterson

Mine maintenance planning, scheduling and daily workflow communications are crucial elements for enhancing overall efficiency and reducing costs. Equally important, it helps identify time periods that equipment will be unavailable so conflicts with production demands are avoided. The current CMMS Kennecott Energy Corporation (KEC) utilizes does not perform these functions in an effective manner. A solution to this problem was to develop an intuitive web-based maintenance planning, scheduling and work flow system call E-MESA. This paper will discuss the E-MESA'S system structure and advantages and disadvantages of using the web based E-MESA solution to perform the maintenance functions described above.

Jan 1, 2002

Projections of coal reserves in Central Appalachia are essential for long-term planning in the region. Annual production is declining in states such as Virginia. And minable reserves for the Central Appalachian coalfield are challenged by difficult geological, mining and market conditions. To project coal mining longevity in this region, interviews with mining companies were conducted to determine and assess technical and economic factors that affect coal seam minability. This information was ap- plied to seam and coal reserve data developed by state and federal governments. The results were analyzed to determine the effects of various factors on the overall minable coal reserve base.

Jan 1, 1998

By Philip M. Rice, Paul Schmall, Peter W. Deming, Hugh S. Lacy

A groundwater cut-off is needed to provide a stable face of tunnels to be constructed by jacking precast rectangular tunnel segments beneath commuter rail tracks for the new I-90 extension in Boston, MA. Extensive obstructions are present within the path of the tunnels. This paper describes how the use of artificially frozen ground is being planned to provide a reliable groundwater cutoff and assure a stable tunnel face. Monitoring during freezing assures continuity of the cutoff. Laboratory testing of frozen soil samples aided the design of this frozen soil boundary. Logistics of installing vertical freeze pipes are described.

Jan 1, 1999

By V. K. Gupta

A detailed experimental study of the variations in grinding rate with particle size, particle load, ball diameter, ball load, mill diameter, and mill speed was carried out for a soft cement clinker and a hard cement clinker. The effects of the ball diameter, ball load, and particle load were observed to be material (hardness) independent, and those of the particle size, mill diameter, and mill speed to be material dependent. A sharp change in grinding behavior was observed for both the clinkers at about 150 µm size. Below this critical size: (1) the hardness difference between the two clinkers became insignificant, (2) variation in the grinding rate with particle size became markedly more pronounced, and (3) mill speed had little or no effect on grinding rate. The importance of these results in the context of process optimization and control is discussed.

Jan 1, 1988

By Vas Choudhry, Randhir Sehgal

Conventional clean coal technologies which consist of coarse coal cleaning by gravity methods and treatment of natural fines by flotation can only remove a portion of the pyritic sulfur and ash in the coal. Higher (+90%) pyritic sulfur rejection is attainable when coals are ground to ultrafine sizes to enhance liberation of the mineral matter and then cleaned. However, cleaning of coal at very fine sizes poses a number of unsolved problems, the chief one being the loss of cleaning efficiency. This, of course, means that liberation of pyrites does not always equal its rejection. In addition, the dewatering of fine- cleaned coal, and its handling, transportation, and acceptability to the utility industry a1 so pose considerable technical and economic problems, especially when compared to the FGD alternative. This paper addresses some of the critical issues involved in the cleaning of ultrafine coal s.

Jan 1, 1989

By Guido Deissnann, Jennifer L. Kirkaldy, Stephan Kistinger, Carol M. Pettit

Contaminated mine drainage presents a potential hazard for aquatic ecosystems and groundwater resources. Reliable predictions of long-term developments in seepage quality are necessary to select reasonable decommissioning options and remediation measures for waste-rock heaps during mine closure and/or mining site rehabilitation to minimize future risks and environmental hazards. Extensive geochemical modeling work was used to assess the consequences of various remediation options for waste rock heaps at a former uranium mine in Eastern Germany. The predicted contaminant discharges are used for an assessment of long- term benefits of decommissioning alternatives to derive conclusions for sustainable remediation measures using risk-based cost/benefit analyses.

Jan 1, 2000

By Fred N. Kissell, Jeffery L. Kohler, Edward D. Thimons

Aerodynamic stall of vane-axial fans is both an operational problem and a safety concern. While deep stall is relatively easy to detect, the diagnosis of a partial stall is often more difficult. Its transient nature and the fact that its symptoms can mimic electromechanical problems of the fan and fan drive assembly, or vice-versa, compound the difficulty of making a timely and accurate diagnosis. A knowledge-based expert system known as FANPRO has been developed to aid in the diagnosis of these problems. FANPRO and its application are the subject of this paper.

Jan 1, 1991

By G. M. Bernard

Cerro Colorado lies on the eastern edge of the Atacama Desert in the foothills of the Andean Cordillera of northern Chile. Compañía Minera Cerro Colorado SA (CMCC) operates Cerro Colorado. CMCC, headquartered in Santiago, Chile, is wholly owned by Rio Algom Ltd., of Toronto, Ontario. Cerro Colorado is located 120 km (75 miles)east of the port city of Iquique. Access is by 30 km (19 miles) of paved highway and 70 km (43 miles) of upgraded road. The mine site is located at an altitude of 2600 m (8531 ft) on a gentle west-sloping plateau adjacent to a deep canyon (Quebrada de Parca) to the north. Temperatures are moderate, ranging from 5° to 30° C (41° to 86° F) with an average annual rainfall of 20 mm (0.8 in.). The plateau is generally covered with 20 to 30 m (65 to 100 ft) of Quatemary sand and gravel overlaying bedrock. In the immediate vicinity of the Cerro Colorado deposit, a semicircular embayment has been eroded into a steep canyon wall that cuts through the surface gravels to expose a considerable section of the underlying bedrock.

Jan 1, 1995

By Thomas E. Shufflebarger

Glass sand is a virtually pure, fine- to medium-grained, quartz sand. It is produced in 25 states from a variety of chemically different source rocks. Deriving their raw material largely from either friable sandstones or loosely consolidated sands, 59 operations produced 14.9 million tons of melting sand in 1976. About one-third of this tonnage was obtained from the Oriskany and St. Peter Sandstones. Glass-sand prospects are discussed in this paper with regard to chemistry, environment, transportation, and costs. Demand for a quality product will range from 36 million to 46 million short tons in 1995.

Jan 1, 1978

By Qun Wang, Elena A. Alonso, Janusz S. Laskowski

Primary normal long-chain amines are insoluble in saturated brine. Their colloidal solubility (dispersion) in concentrated electrolyte solutions is strongly affected by the presence of surfactants (frothers). This paper shows that a better usage of alcohol type surfactants, which are commonly used in potash ore flotation as frothers, can significantly improve the flotation of both coarse and fine sylvite particles. A new process of potash ore flotation is developed, which includes premixing an effective frother with an aqueous solution of amine or emulsion of extender oil containing amine. With such a combination of flotation reagents, KC1 particles up to 5 mm in size float very well in the short flotation column, and particles up to 2 mm float in a mechanical cell; when used to treat fine fraction-containing sample, this method may as well provide an improved concentrate grade.

Jan 1, 1995

By Carol Cox Russell

More than two thousand abandoned mines within the Animas watershed in Southwestern Colorado are being prioritized for remediation by the Animas River Stakeholders Group (ARSG). Phased collection and assessment of information progressed from large scale to site specific. Prioritization was based on existing or potential environmental impact and technical feasibility of remediation as measured by dissolved Cd, Cu, and/or Zn in the discharge; indicators of habitat degradation; aquatic life in streams; cumulative impacts at the point of compliance; cost effectiveness; treatiblity/feasibility; and cultural and historic preservation.

Jan 1, 2000

By Kent G. Homewood

The well-being of any company is directly related to the well-being of its employees and to the effectiveness with which the personnel resource is managed. In an era when personnel management has steadily become more complex, there is an increased awareness of employee information systems at all levels of management due to: (1) regulations enacted by federal, state, and local government agencies; (2) technological advances within the mining industry which have resulted in the requirement for highly skilled personnel; (3) increasing concern for the confidentiality of employee information; and (4) management's need for information for planning purposes to control costs and for early recognition of trends and potential problems. In the past it was sufficient to maintain records manually. Today computers are necessary to provide information on short notice and effectively manipulate large volumes of' data. This discussion will describe the following aspects of employee information systems: (1) collection and maintenance of information, and (2) applications which include employee health, salary administration, management re- sources, and labor negotiations.

Jan 1, 1979

By John E. Urosek, Herman Schade

In March, 1988, a fire occurred in a large underground coal mine. Coal Mine Safety and Health of the Mine Safety and Health Administration was immediately notified of the situation. They requested the assistance of the Pittsburgh Health Technology Center (PHTC) to provide monitoring and analysis of the mine atmosphere in and around the fire area to insure the safety of the miners escaping from the mine and for the miners involved in extinguishing the fire. The capability to provide this type assistance is maintained by the PHTC Offices located at 4800 Forbes Avenue, Pittsburgh, Pennsylvania. The equipment used is maintained field ready and can be mobilized almost immediately. This paper will discuss the response to this recent major mine fire.

Jan 1, 1989