Search Documents

By J. C. Stankus

In this paper, an innovative concept in longwall tailgate support is discussed. This new concept utilizes a new high capacity roof truss system in lieu of conventional wooden crib block. The first field test was conducted at Bailey Mine and was very successful. Similar tests have been installed in other mines and seams. An extensive instrumentation plan was designed and implemented in the truss test area. The test data has shown that the dynamic roof truss system effectively controls the various abutment pressures caused by longwall mining thus maintaining a stable tailgate entry.

Jan 1, 1995

By C. Pace, D. Darlington, A. Montera, C. Lingren

"A phosphate beneficiation plant in Utah is using isotope-based Prompt Gamma Neutron Activation Analysis (PGNAA) technology to analyze the entire slurry streams of the incoming feed and final product in order to adjust the flotation circuits in near real time and optimize the plant output. The plant has gained greatly improved visibility/control and has reduced product variability for improved profitability and product quality. This paper takes a look at the economics as well as application details and the difference this technology provides in a phosphate application. SIMPLOT PHOSPHATES INTRODUCTION Simplot’s Vernal, Utah Phosphate Mine and Mill are located in the northeast corner of the state in the Uinta Mountains along US Highway 191, eleven miles north of the town of Vernal. The phosphoric acid and fertilizer plant fed by the Vernal mine is located 94 miles Northeast of Simplot Phosphates in Rock Springs, WY.At the Vernal plant, loader and shovel mining to 85 Ton capacity trucks is done at an annual rate of 3.8 Million tons of ore. Run of mine ore is crushed in a mineral sizer to minus 14 inch diameter at the rate 11,500 tons a day and transported to the SAG Mill’s 130,000 ton surge stockpile by overland belt. ORE RESERVES The ore is a Phosphoria Formation of sedimentary rock type dating to the Permian Age. The ore body rests over a 25 mile area on Weber Sandstone from the Pennsylvania and Permian geologic period. Layers of Phosphate Rock can vary in thickness from 0.3 up to 2.1 feet, alternating with layers of Mudstone. The eastern edge of the ore’s body Panel “G” runs 16 feet deep with a feed grade of 21.5% P205 with lower MgO diluents of less than 2.79%."

Jan 1, 2016

By Michael A. Trevits

The National Institute for Occupational Safety and Health (NIOSH) in partnership with Strata Products tested the sealing capability of Ventstop®? as part of an ongoing mine fire control and suppression research program. Ventstop®? is a multi-purpose, inflatable device that is produced by Minvent Solutions and is available world wide for use in the metal and nonmetal mining industry. Ventstop®? is also used in the Australian coal industry as a temporary ventilation control device. The device can be quickly deployed, is reusable and can be placed in horizontal and vertical mine voids to control dust, fumes and smoke. Deployment, multi-day inflation and air leakage tests were conducted at the NIOSH Lake Lynn Laboratory to determine the capability and limitations of Ventstop®? in a simulated coal mine setting. During the tests, Ventstop®? was also subjected to low level forces of a nearby methane gas ignition. It is thought that Ventstop®? could be used by the US coal mining industry to temporarily close an underground mine area in response to a fire or spontaneous combustion heating event, to temporarily redirect mine ventilation during longwall equipment moves or during stopping construction. This paper describes this inflatable temporary mine sealing technology and presents the results of the NIOSH tests.

Jan 1, 2009

By J. L. Kohler

Control circuit failures contribute significantly to continuous miner downtime. The time required to put the machine back into production is a function of the time required to diagnose the problem, obtain parts, and make the repair; of these, the diagnostic time is often the largest. A microprocessor-based system with the ability to diagnose all of the common control circuit failures was designed, installed on a continuous miner, and tested. This paper summarizes the development of the diagnostic system, and provides examples of the system's diagnostic capabilities. Implementation issues and the hardware used for the prototype are briefly described. Finally, comments on the system's performance are presented.

Jan 1, 1993

By R. E. Williams

University of Idaho scientists research under U.S. Bureau of Mines Cooperative Agreement C0278001 constitutes a complex hydrogeological, hydrochemical and metallurgical mine waste management project at an existing Superfund site. Technologies that may prove useful for the extraction of dissolved metals from acid mine water and solid wastes include lixiviation and biosorption. Acid mine water is the major, long-term problem in the valley. We are attempting to delineate the major sources of ground water recharge which feed the acid mine drainage and their hydraulic properties. Grouting of recharge areas may facilitate minimizing the production of acid mine drainage if recharge pathways can be identified.

Jan 1, 1990

By T. A. Toney

A sampling program was conducted in 2008 to determine the run of mine characteristics of 5 coal seams. The sampling program included size analyses and float sink determinations. The samples were analyzed for ash and mercury concentrations for each size and gravity fraction. This paper will report on the sampling program, the analytical results, and the correlations determined in the data set investigated.

Jan 1, 2010

By P. A. S. Manning

Eastern Jamaica consists predominantly of non-carbonate rocks reaching elevations of over 2200 m. The area is drained by a well established river network which supplies close to 30% of the sand and gravel used by the building and construction sector. Present high extraction rates and slow rates of replenishment will result in early exhaustion of this source of aggregate. A number of volcanic and carbonate rocks are being examined as a possible source of high quality aggregate which meet the requirements for all types of construction. Preliminary evaluations show a dacitic deposit to be the most suitable source for aggregate use.

Jan 1, 1998

By E. Pizarro

Division Andina has considered in its long range planning, the exploitation by panel caving method of "Third Panel" mine, which was started its production stage during the second half of 1995. This mine has two production levels, the first is grizzly level and another is L.H.D. level. Both sectors use the same haulage level where mineral is recollected through ore pass. For mineral loading and haulage its use 50ton diesel trucks combined with electro-hydraulic chutes. The automation has permitted what this operation is carrying out with remote control by driver's truck, in concordance to short range planning.

Jan 1, 1998

By P. S. Hettinger

Land Application Discharge (LAD) is a useful method of disposing of waste water from mining operations and in certain climatic regimes, stormwater runoff. LAD systems function under the premise that metals, salts and nutrients in water are dispersed over a large area and are effectively assimilated into the soil profile. Depending on the soil structure, migration or mobilization of dissolved metals through the soil profile can be Substantially reduced. Land application of treated effluent from sewage lagoons or waste water plants was probably the first general use of land applied water. LAD has gained popularity with the mining industry as a means of disposing of waste water and process water. In addition, large volumes of snow meltwater and stormwater are often placed in storage in Montana during spring, and Land Application Discharge has shown to be an effective method for disposing of stormwater during the dry, summer season. LAD can also provide an alternative to recycling or treating waste water at on-site waste water treatment plant&. Application of stormwater or process water can result in little or no change to the background concentrations of metals in baseline water quality samples. One cautionary note about LAD: high salt concentrations and pH values are associated with process water from heap-leach facilities and are known to cause burning of local vegetation. Some pre-treatment of process water may be necessary to prevent such environmental problems.

Jan 1, 1994

The removal of tritium from tritiated water (-0.5 µCiIL) was studied by metallothermic reduction using aluminum. The influence of the three variables namely the aluminum powder amount, the NaOH concentration and the reaction time has been studied on the tritium activity reduction. The experimental results and statistical analysis showed that more than 85% of tritium can be removed from the tritiated water. Further work on the tritium recovery as well as efforts to totally decontaminate water by incorporating a cryogenic concept is currently pursued.

Jan 1, 1998

By C. Haycocks

The evolution of longwall mining is briefly traced from its inception in England in the 1620's. In the beginning this method recovered 90% of coal with roof closure controlled by packs and walls. Mechanization began with kerf cutting, crude face conveyors, and improved face support. Full face mining was accompanied by the introduction of self-advancing hydraulic supports. U.S. longwalls evolved a retreating system to recover blocks of coal outlined by room and pillar panels. Computer control combined with the most modern technology has greatly increased productivity. Past trends are used to predict future technological directions.

Jan 1, 1997

By R. Day

Nahcolite is a naturally occurring sodium bicarbonate mineral found principally in the Piceance Creek Basin of northwest Colorado. An 8-m thick nahcolite bed, 610 m below the surface, is the target of this first commercial nahcolite mine. A chamber and pillar mining system is developed by solution mining parallel 8-m tall by 18-m wide by 450-m cavities initiated along horizontally drilled holes. Hot water leaching, cooling crystallization and flash drying is the process. The sodium bicarbonate product is consumed by the baking, animal feed, industrial and acid rain abatement markets. A project overview, emphasizing the combination of horizontal drilling and solution mining technologies, will be presented.

Jan 1, 1994

By W. Robert Power

Dimension stone includes a wide variety of natural materials that are put to an equally wide variety of uses. It is possible to classify dimension stone according to the end use to which the stone is put or according to the lithology of the stone. Both schemes are used by the United States Bureau of Mines in the annual Minerals Yearbook. The 1969 Yearbook lists 15 specific uses and has additional miscellaneous catagories. The same Yearbook lists five specific rock types or lithologies, and also includes a miscellaneous category. In a short presentation it would hardly be possible to list and define all these categories, much less discuss the evaluation of deposits with regard to all possible combinations. Besides, I am only slightly familiar with some of the uses and their requirements. I have therefore chosen to limit my remarks to some special problems in evaluating dimension stone that is to be cut and finished to specific sizes, tolerances, and finishes for use in buildings and some monuments. This use class is called cut stone in the Minerals Yearbook. In terms of dollar value it is the largest single use category. In 1969 the dollar value of cut stone was $29,122,000 which is more than twice the value of the next largest category. For those of you who are interested in other use applications of dimension stone I suggest that you start with recent articles by Bowles (1960), Currier (1960), and Barton (1968).

Jan 1, 1972

By B. Mirabile, B. Stables

Standing support is often used in conjunction with underground retreat mining. Knowledge of the load-displacement behavior of a standing support, and loading induced by the mine opening is critical to proper support selection. The NIOSH STOP database contains load-displacement laboratory test data for most commonly used standing supports. Hydraulic load cells currently used to measure in-situ loading of standing supports have exhibited leakage under load, producing irregularities within the dataset. An improved hydraulic load cell eliminates leakage and produces more consistent data. INTRODUCTION A hydraulic load cell, more commonly known by “flat jack” or JackPack, is a device installed to determine the loading characteristics of roof to floor supports. These standing or roof to floor supports include, but are not limited to: pumpable cribs, cans, wooden cribs (4-point, 9-point, etc.), metal props, wood timbers, concrete donut cribs, and other variations of these standing supports. Flat jack devices have been used previously to determine the loading of such roof to floor supports. The most commonly used load cell for standing supports is based on a design intended for pre-stressing standing supports, not load measurement. These load cells are produced in South Africa, and can be formed into several different shapes depending on the applications (Barczak). Flat Jacks are manufactured in various shapes and sizes depending on the application, common shapes are square and round that are 25.4 mm (1.0 inch) thick when collapsed as shown in Figure 1. The sheet metal that makes up the bladder is comprised of 19 gauge or 1.11125 mm (0.04375 inch) thickness, the top and bottom pieces of sheet metal are resistance seam welded around the perimeter. There are two different ports installed on one of the bladder skin corners of the flat jacks; these ports allow a fluid to fill the unit and the other port has a relief valve. The fill port is comprised of a check valve. The pressure relief valve is located in the second port; preset to 1724 kPa (250 psi), pressure relief valve will keep the load cell from bursting. Bursting of these load cells typically causes a small tear in the metal skin allowing the fluid to leak out without a large catastrophic failure. The effective inflation range of these load cells is between 25.4 mm (1.0 inch) to 254.0 mm (10.0 inches) thick. Different types of fluids can inflate these load cells but the most common and easily accessible fluid for testing applications is water. Water pressure from the mine supply line can inflate these load cells to the desired load. Depending on the pre-stressing requirements a pneumatic powered pump, hydraulic pump or hand pump may be required to inflate the load cells.

Jan 1, 2019

By J. S. Peterson

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center (PRC), has conducted research to improve electrical fault detection on coal mine direct current (dc) trolley systems. Present circuit breaker protection systems are current-magnitude-based and cannot discern between normal traffic and high resistance electrical faults. Tests were conducted at cooperating mines to assist in developing a neural-network-based detection algorithm for distinguishing between electrical faults and normal operation. The Fast Fourier Transform of the trolley rectifier current signature served as baseline data for the neural network. During field tests, the algorithm performed with greater than 90% accuracy.

Jan 1, 1997

By M. J. Virnig, G. A. Kordosky

Throughout time, the mining industry has been very successful in meeting the world's requirements for metals and materials while meeting the challenges of decreasing ore grades and increased emphasis on protection of the environment. This success has been due to the development and implementation of new technologies. A clear example of such a development over the past 25 years is the increasing use of leaching/solvent extraction/electrowinning for the recovery of copper from oxide and sulfide ores. The key to the successful introduction of this technology was the discovery and development of the hydroxyoxime liquid ion exchange reagents by General Mills Chemicals (now Henkel Corporation). An important role was also played by the close working relationships between General Mills Chemicals and Ranchers Exploration which resulted in startup of the first plant in 1968 and between General Mills Chemicals and Bagdad Copper which resulted in the startup of the second copper SX-EW plant in August of 1970. Following on the heels of the hydroxyoxime development came the commercialization of other new chelating reagents based on different chemical functionalities, i.e., beta-diketones, alkylated 8- hydroxyquinolines and sulfonamidoquinolines. This initial spurt of activity was then followed by a slowing of development in terms of new reagent functionalities. Activity has continued in terms of further optimization/improvement of existing reagent functionalities but the commercialization of new reagent functionalities has slackened. This observation reflects the fact that the development of new reagent functionalities for metal recovery has become increasingly more expensive such that the right combination of price and sales volume must exist in order to justify the investment required to bring a new reagent to the market place. Given the dependence of the mining industry on innovation to meet the needs of the future, one can ask how these new developments, particularly in new reagents, will occur. To arrive at an estimate of the costs involved in commercializing a new metal extractant functionality, particularly a chelating type functionality, a case study of the development of LIX ®* 34

Jan 1, 1994

By V. Voller

A relatively simple model of grinding which incorporates both the Bond grindability equations and the population balance equations has been extended to form a comprehensive simulation package that can describe most kinds of conventional grinding circuits. The package has two programs, with the first consisting of an input program which helps the user to specify the prescribed circuit, while the second program performs the actual simulation. The package serves two main purposes - i) as a check on mill design, with the output providing not only predictions for the product passing size but also of the full product size distribution, and ii) as a means to assess the likely effects on the product size distribution of operating under different sets of conditions.

Jan 1, 1981

By Joseph W. Johnson

General Electric introduced electric drive systems on 85 ton Off-Highway mining trucks in the early sixties. Due to favorable economics, trucks have increased in size to handle larger payloads. Series Motorized Wheel systems were developed to meet this demand. When the technology was available, General Electric switched from use of Series motors to separately excited motors with the added benefits of static exciters and simplified control. Over 20 years of electric drive experience have been incorporated in the STATEX drive systems, which covers truck sizes from 85 to 220 tons. This paper traces the drive system developments from the early stages to the present and takes a look at what's ahead.

Jan 1, 1983

By L. G. Kirk

The Mississippi embayment ball clay region, including western Kentucky, western Tennessee, and northwestern Mississippi, accounted for more than 95% of the total U.S. ball clay production during 1985. Other producing states during the year were Texas and Maryland. The U.S. Bureau of Mines reported total domestic production for 1985 of 910,000 short tons. The United States exports approximately 20% of the annual ball clay production. Geologically, the ball clay deposits are sedimentary in origin and occupy the north- eastern flank of the Mississippi embayment. The commercial deposits have been confined to the Claiborne and Wilcox formations within mid to lower Eocene and upper Paleocene age strata. The deposits are lenticular in nature and highly variable in areal extent and thickness. They exhibit very abrupt lateral boundaries and are bounded laterally and vertically by unconsolidated sands, silts, and waste clays.

Jan 1, 1986

By J. Szarkowski

"INTRODUCTION The Butte district of Montana is well-known as one of the biggest historic producers of copper in the world. It is also a classic example of a porphyry Cu-Mo system that has been overprinted by zoned, polymetallic (Cu-Zn-Pb-Ag) lode mineralization. After copper, silver was the next most important metal mined from Butte, with over 700 million ounces of total Ag production between 1880 and the present day. Although many papers have been written on the mineralogy of the early porphyry Cu-Mo mineralization and the high-grade Cu-rich lodes in the center of the district, relatively little information exists on the mineralogy of silver in Butte. The purpose of this paper is to summarize past and present silver production trends for the district, and to combine previously published work with new research to examine the mineralogy of silver in the Butte mining district. BUTTE HISTORIC SILVER PRODUCTION According to a recent USGS compilation1, Butte is one of the most Ag-rich porphyry deposits in the world, both in terms of average Ag grade (8.6 g/ton) and total production + reserves (Fig. 1). It is also the 2nd biggest Ag-producing mining district in the U.S. (after the Couer d’Alene district, Idaho). Annual silver and copper production data for the Butte district, compiled from various sources2,3,4, are summarized in Figure 2. Peak production of Ag and Cu was in 1917. While Ag production gradually declined in the ensuing decades, Cu production remained strong until the years leading up to the closure of the Berkeley Pit in 1982. In 1984, mining of the nearby Continental Pit resumed under a different operator, and continues to the present day. The Continental mine produced an average of 35,000 metric tons Cu and 575,000 oz Ag per year between 1984 and 20044. These figures do not take into account a period of mine closure in 2001-2003 due to an unexpected hike in utility prices. The long-term decline in Ag/Cu ratio of ore mined in Butte (Figure 3) is due to several factors, including: 1) changes in metal prices; 2) a downwards decrease in Ag/Cu ratio of most of the lodes with depth below surface; and 3) a shift in mining methods from selective underground mining of high-grade veins to open-pit mining of the bulk rock."

Jan 1, 2016