Search Documents

By Ching-Yi Tsai

The effect of various constituents on the pyrolysis and combustion of a pulverized coal in an entrained-flow reactor has been inves¬tigated. Predicted time-temperature histories of the coal' particles and experimental weight loss data indicate a strong coupling of heat and mass transfer to the pyrolysis and combustion rates. A higher combustion rate following ignition was observed as particle size was increased to 112 µm. This is related to a higher particle temperature after ignition for the larger particles. Although the heating rate prior to ignition decreases with increasing particle size, higher slip velocities and surrounding gas temperatures for the larger particles promote early ignition. The presence of liptinite in the coal increases the weight loss rate before and immediately after ignition. Similar behavior was observed for pyrolysis. Fractions of a HVA bituminous coal which were rich in mineral matter or semi-fusinite were found to have a higher heterogeneous char combustion rate than vitrinite rich samples.

Jan 1, 1984

By M. Li, J. K. Thompson, A. S. Azman

Powerful mining systems typically generate high-level noise that can damage the hearing ability of miners. Engineering noise controls are the most desirable and effective control for overexposure to noise. However, the effects of these noise controls on the actual hearing status of workers are not easily measured. A tool that can provide guidance in assigning workers to jobs based on the noise levels to which they will be exposed is highly desirable. Therefore, the Pittsburgh Mining Research Division (PMRD) of the U.S. National Institute for Occupational Safety and Health (NIOSH) developed a tool to estimate in a systematic way the hearing loss due to occupational noise exposure and to evaluate the effectiveness of developed engineering controls. This computer program is based on the ISO 1999 standard and can be used to estimate the loss of hearing ability caused by occupational noise exposures. In this paper, the functionalities of this software are discussed and several case studies related to mining machinery are presented to demonstrate the functionalities of this software.

Jan 1, 2016

By Mark E. Gershon

A mixed-integer formulation of the mine scheduling problem is discussed and applied for the purpose of optimizing both the mine production sequencing and the mill blending and processing problems simultaneously. Previous attempts at solving these problems separately, although successful, fail to take into account the interrelationships between these problems. Project structure serves as the outline of this paper, which is directed towards a mining engineering audience. Generalized in its organization, this concept is useful for long, intermediate and short range scheduling. Actual applications are mentioned which show that the concept is also applicable to mining a variety of ores.

Jan 1, 1982

By M. S. Basich, J. S. Scope1, J. H. Raeder

During 1983, The Youghiogheny and Ohio Coal Company's lost-time-incidence rate was 8.1, equal to the average for underground bituminous operators. How- ever, one half of all lost-time injuries were low back, back and neck related. In reviewing these results, we determined that substantial improvement could be made. We investigated existing back schools and the possibility of opening an in-house clinic. In September 1984, we began The Youghiogheny and Ohio Coal Company's Back Care Program. The objectives of the program are to reduce the number of back injuries incurred at the work site, hasten recovery time, decrease medical and workers' compensation costs and provide the employee with a thorough understanding of his problem. A state-of-the-art clinic capable of treating injuries to the spine and extremities has been established at the work site. The clinic is staffed by a licensed physical therapist and is offered to all employees on a voluntary basis under physician referral. The approach to treatment is multi-phasic. For the typical patient, the initial goal is to reduce pain and correct dysfunction. Treatment modalities such as auto-traction, extension exercises, ultra sound and moist heat are frequently used. During this period the patient is given extensive education regarding his problem. As soon as more vigorous activity can be tolerated, a work-hardening pro- gram consisting of job simulation activities designed to improve flexibility, strength and functional capability is begun.

Jan 1, 1986

By K. H. Nimerick

Froth flotation of coal is growing in importance and complexity. Some of the reasons for these changes follow. 1) A need exists for energy resource conservation. 2) Preparation plants are processing widely varying coal -- deep seam, strip and stockpiled either separately or as blends. 3) More fines are being generated because more mines are using automatic mining equipment. 4) It is more practical and economical to remove ash and sulfur at the preparation plant than during utilization.

Jan 1, 1982

By Louis J. Czel

Although lithium was first discovered by Arfwedson in Sweden in 1817, it did not reach any significant status in commercial application until 1908 when Thomas A. Edison received a patent covering the use of lithium hydroxide in alkaline' storage batteries. Edison's achievement can be regarded as a major breakthrough in the development of the lithium industry. In the years prior to 1908 lithium salts had found only modest applications in the pharmaceutical and pyrotechnic fields. The next important milestone in the growth of this net industry occurred in Germany in 1918 when Metallgesellschaft at its metallurgical laboratory at Frankfort-on-Main discovered that the addition of a few hundredths percent of lithium metal to aluminum and its alloys increased-the hardness. This brought into being a new commercial use of lithium in the manufacture of bearing metals. The new material, called "Bahnmetall" (railroad, metal), was widely used for, many years in the manufacture of bearings for railroad and automotive purposes. Its use continued until the early 1930's and there was a short-lived renewal of its production during World War II. Subsequent use of-the alloy was soon outmoded.

Jan 1, 1961

By Jim McKinley

With a growing number of mines reaching closure and seeing closure costs materialize, regulators, lenders, and banks are observing projects that fail economically by miscalculating these costs. Mine closure costs are often categorized as a type of liability which is defined as the money owed by the company to offset effects from the project, and the money available to pay for those debts (e.g., bond). Often, decisions made before Day 1 of mining (e.g., co-disposal, dry stack tailings, waste segregation) can significantly change the bond calculation. Once the bond is calculated and funded, operators are encouraged to conduct closure research and use applied science for progressive bond release prior to final closure. However, this author has observed few instances of financially significant progressive bond release, as there are typically no robust procedures for bond return, either before or during closure activities. As a result, many companies decide that entering a state of Care & Maintenance (C&M) is less risky than attempting to fund closure activities with an unknown bond return mechanism. Although perhaps less risky in the short-term, the primary long-term risk with entering C&M is that it increases the chances of the bond not covering the cost of closure and the chances of the government/regulatory agency inheriting the mine closure. Bonds are typically reevaluated on a regular cycle (e.g., five years) so every mining company goes through this financing challenge eventually.

Feb 22, 2026

By Hugh D. Olmstead

Typical operations necessary to develop oil and gas reservoirs are reviewed, including exploration, drilling, cementing, completion, work over, sand control, stimulation, enhanced recovery and production. The role of industrial minerals in these operations is described. Some of the opportunities and problems affecting increased use of industrial minerals in drilling and stimulation are discussed.

Jan 1, 1983

By John Durkin

A system based on seismic techniques has been developed to detect and locate men trapped underground following a mine disaster. Both theoretical and field studies have been used to generate models to predict the performance of the system. For a strong source, it is almost certain that the miner's signal will be detected if the geophone array can be positioned over a likely area of entrapment. After signal processing, it is highly likely that the location of the miner can be determined within an accuracy of 100 ft (30.5 m). The system is presently operational in a state of readiness in the event of a mine disaster.

Jan 1, 1980

By Miguel Angel Ibarra

This paper describes the results of a digital computer simulation study in which the impact of the proposed truck dispatching on the overall mine productivity was investigated for an operating open pit mine. In the study, the existing operation was first simulated for a one-month period, using both the actual time study data and the computed cycle times. By adjusting certain input parameters to the simulation program, the actual one month production was first duplicated through simulation. Afterwards, the operation was again simulated in a dispatch mode. Comparison of simulation results under the dispatch mode, with the initial base case simulation results, showed a definite improvement in overall productivity with dispatching; i.e., approximately 10% gain for the operation. As expected, the results also showed that the extent of possible improvement did vary with the particular pit configuration being investigated.

Jan 1, 1980

By Lewis J. Patterson

In the period of time allotted to this paper, an attempt will be made to cover a great deal of territory, figuratively speaking, as far as our experience with ammonium nitrate is concerned. In giving this subject the "broad-brush" treatment, it will be necessary to generalize on the major points which at the same time will permit me to avoid, to a great extent, any involvement in the purely technical and theoretical aspects of blasting. The practice of theorizing before a new idea is tried has practically been discontinued in our organization simply because experience has shown that, almost without exception, theories have fallen aside as some new development takes its place. In regard to blasting, logic and experience seem to have little place in this phase of quarry operations. As the use of low cost blasting agents was introduced in our operating practice, a man who had no previous experience in the field of blasting but with sound knowledge in safety procedures was given the responsibility of supervising the drilling and blasting operations. A total lack of experience is not ordinarily recommended as a prerequisite to assuming the responsibilities of a supervisory position. However, in this case it was obviously a wise decision because there were no pre-conceived ideas as to what techniques would or would not be successful.

Jan 1, 1958

By Harlan L. Kebel

Gypsum, the dihydrate form of calcium sulfate, has a history of usefulness to man dating back several thousand years, and a worldwide industry has been built on the mining and processing of this versatile industrial mineral. However, anhydrite, the other prin¬cipal calcium sulfate mineral, has very limited use, so much so that separate statistics for it are not always kept, but are usually included with those for gypsum. Although often found in close association, the two minerals have important chemical differences in that anhydrite is the anhy¬drous form of calcium sulfate (CaSO4) whereas gypsum is the dihydrate (CaSo4.2H20). These two molecules of combined water result in significant differences in hardness, density, and solubility of the two minerals. Of most importance, however, is the difference in thermal properties wherein gypsum, upon the application of a modest amount of heat, can be converted to the hemihydrate of calcium sulfate (CaSO4 '21H20) or plaster of paris, an intermediate product upon which is based over 90% of the value of all calcium sulfate end products. Anhydrite, on the other hand, is inert at these temperatures and its uses have been limited to only those few cases where calcium sulfate in the anhydrous form may have an advan¬tage. The earliest known use of gypsum plaster dates back some 5000 years to the time of the Pharaohs of Egypt who had discovered that gypsum rock, when exposed to fire, broke down into a powder which, when mixed with water, would form a putty that could be plastered on a rough mud brick or stone wall to make a smooth finish. It was used down through the centuries in a limited way for ornamental purposes, but did not achieve wide acceptance because of the quick (25 to 30 min) setting or hardening time which made it difficult to use. The first real understanding of gypsum chemistry was developed in France about 1755, and the gradual growth of its present utilization dates from that time. In the United States, the first utilization of gypsum was to grind it to a fine material for use as a soil conditioner at about the time of the Revolutionary War, and the term land plaster for ground gypsum was coined and has remained in use. Another cementitious material-lime or calcium oxide-had become the usual plastering material, but by about 1870 a method for retarding the set of gypsum plaster was discovered; today it has almost completely replaced lime as a plastering material. In recent years, gypsum products sold in the United States have reached a total valuation of approximately $2 Gpy as illustrated in [Table 1].

Jan 1, 1994

By Jeffrey J. Daniels

Advances in borehole geophysical research for mineral assaying, and remote detection of mineralization away from the borehole. Nuclear activation measurement research has provided accurate in situ assays of economic metals with neutron-gamma activation, using a high resolution intrinsic-germanium detector. Although nuclear activation analysis is the present "best-hope" for obtaining in situ assays for some elements, gamma-gamma and magnetic susceptibility measurements can provide accurate assays for lead-zinc and magnetite, respectively. Borehole optical spectroscopy and x-ray fluorescence are being investigated as possible in situ assaying techniques for some minerals. More laboratory and field calibration research is needed before nonlinear complex resistivity (NLCR) can be routinely used as a quantitative assaying tool. Field tests have shown that variations in the local geologic environment can affect the quantitative accuracy of assay values from downhole NLCR measurements. Deeply penetrating borehole geophysical methods are increasingly being used for mineral exploration as drilling costs and exploration have increased. Borehole electrical measurements have been shown to be useful for detecting conductive orebodies that are not interesected by a drillhole. Hole-to-surface resistivity, and surface-to-hole time-domain electromagnetics are demonstrated to be particularly effective for defining mineralized zones in a massive sulfide environment. Borehole gravity meters and three-component magnetometers have been developed and should prove useful for defining geologic anomalies away from the drillhole.

Jan 1, 1985

By Douglas M. Smith

The town of Tayoltita, Durango is located at the bottom of the 2000 m. deep Rio Piaxtla canyon on the axis of the rugged Sierra Madre Occidental mountain range. Throughout most of the year access to the town is restricted to travel by mule or STOL aircraft. Silver and gold have been produced from epithermal veins in the north side of the canyon since 1757. During the last seventy-three years more than 4,588,000 kg. of silver and 76,322 kg. of gold have been produced from approximately 6,000,000 metric tons of ore. The Tayoltita mine is developed within a fault block bounded by normal faults which strike north-northwest and have opposing dips. A thickness of at least 1300 meters of late Cretaceous or early Tertiary volcanic rocks is exposed in the mine. These range in composition from andesite to rhyolite. Andesite predominates in the upper 750 meters of the section. The volcanic rocks were passively intruded by quartz-monzonite and andesite stocks during middle (?) Tertiary time. Mineralization spatially and temporally (?) related to the stocks occurs along the east boundary fault and in intersecting footwall fissures which strike east-west and northeast. Ore was deposited over a vertical range of up to 600 m. prior to tilting of the volcanic rocks 35 to 45° to the east. With few exceptions, the ore bodies are found within the lower 400 to 500 m. of the andesite. Argentite (acanthite), stromeyerite, jalpaite, electrum and native silver are the principal ore minerals. They occur in gangue composed of one or more of the following: quartz, calcite, bustamite, adularia, chlorite, and albite. Base-metal sulfides make up less than 1.5 percent by weight of the ore.

Jan 1, 1974

By Christian F. Baiz

Industrial minerals can have similar financing requirements to those needs of metaliferrous and coal mining projects. Although, one may see many similarities in the fundamentals of the various risks that must be evaluated in lending to any specific project, one of the outstanding differences is the understanding of the many different markets that these industrial minerals represent. There are in excess of 30 principal industrial minerals ranging in terms of annual production from the largest quantity such as sand and gravel, to possibly the smallest quantity of production of a legitimate industrial mineral which may be defined as industrial and rough gem diamond. If we assume that it is necessary to finance independent projects of ore bodies of industrial minerals for development, the financing techniques are similar to the fundamentals that we would use for financing coal projects or metaliferrous deposits. Therefore, let's begin by redefining project financing in the traditional banking or private sector area, and then in the later development of this paper, we will apply these techniques to industrial minerals in general and cite it with several specific examples.

Jan 1, 1982

By Matt Bilson, Ritesh Mahajan, Antoni Kuras, Wataru Okada

The Waterview Tunnel comprises twin 2.4 km long 13.1 m internal diameter three lane road tunnels in Auckland, New Zealand. The City Rail Link (CRL) is a 3.45 km long, 6.24 m internal diameter twin rail tunnel underneath Auckland’s city center. This paper presents an overview of the tunnel geometry, segmental lining congurations, geometric constraints, performance criteria and functional reuirements for the large diameter Waterview Tunnels and smaller diameter CRL tunnels. Other key aspects, which include sustainability, innovations, construction performance and practical aspects are discussed and compared. Lessons learnt from these mega tunnelling projects are also presented.

Jun 23, 2024

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, Matthew Gordy, Patrick Zhang

Waste phosphatic clay presents a difficult disposal problem and a significant loss of P2O5. Recent developments make this study on the use of phosphatic clay as a feed material for H3PO4 production worthwhile. (a) New data from Florida Industrial and Phosphate Research Institute (FIPR) suggest that the Bclay^ waste can be effectively treated by improved solid separation coupled with flotation to produce feed material for recovering additional phosphate. (b) The use of BOLI Flowsheet^ provides capability to predict performance of aqueous-based processes for a range of possible operating conditions. Using the new FIPR data and BOLI Flowsheet^ enabled the design of a new process that can potentially extend the usefulness of current P2O5 ore deposits. Predictions using OLI Flowsheet were able to identify process conditions that effectively overcome the difficulty of high Mg content of phosphatic clay. Estimated manufacturing cost in the current study lead to valuation of the P2O5 content of the phosphatic clay recovered/utilized at 60 to 70% of that of the phosphate rock feed material currently used. Phosphatic clay should be considered as a valuable material that is currently given zero value. The new FIPR data and BOLI Flowsheet^ enables the design of a new process that can potentially extend the usefulness of current phosphate ore deposits by extending the fraction P2O5 of recovered

By S. M. Hsiung

This paper presents the results of an extensive study concerning a series of roof falls in a room-and-pillar coal mine located in West Virginia. Three dimensional finite element modeling was employed to identify the possible causes for the roof falls. The effectiveness of possible roof control measures for alleviating or eliminating the adverse roof conditions is analyzed, discussed, and compared. The best mining alternatives are recommended. It has been found that large overburden depth and typical roof geology are the major reasons for the roof falls. Angle bolting may not solve the problem encountered in the mine studied. Changing the mine layout currently used in the mine appears to be the best alternative. The recommended pillar size and entry width which will eliminate the problem completely are 90 ft. x 90 ft. and 14 it., respectively.

Jan 1, 1985

By Hasan Sevim

This paper summarizes recent developments in modeling of underground coal slurry haulage networks for determination of optimum design and operating parameters. The model presented here is based on a stochastic dynamic programming formulation, applicable in any typical room-and-pillar and/or longwall mining configuration commonly practiced in the United States. The formulation and the structure of the model is general enough to handle design problems involving more than one face and mining method. Given the stochastic operating characteristics and a system layout, the model can be used to determine the equipment configuration and operating regimes that minimize the overall unit cost of coal haulage.

Jan 1, 1983

By Wayne S. Cavender

The geochemical association of arsenic and gold in epithermal precious metal deposits of the Basin and Range province is well documented, and in this paper I wish to discuss the evaluation and utilization of this element association for geochemical gold exploration. In 1961-62, I conducted an exploration program on lands controlled by Getchell Mine, Inc, and centered about the Getchell gold mine itself, Besides exploring for new gold deposits, the program was to evaluate these lands for potential deposits of any type; thus, a multi-phase program encompassing a number of exploration methods was conducted. I shall not elaborate on the process of designing the program or of integrating the various methods, but for gold exploration, geochemical methods were determined to have the best potential. This paper is based on that effort. Figure 1 shows the exploration area, which covers the northern half of the Osgood Mountains in eastern Humboldt County, Nevada. The Getchell $line is on the east flank of the range and is about 40 miles northeast of Winnemucca.

Jan 1, 1964