Search Documents

By E. G. Davis

The flash reduction of fine iron ore in a dilute-phase system was investigated at 500° to 900° C within a heated stainless steel tubular coil. Alabama brown iron ore and Mesabi semitaconite ore were fed into the coil concurrently with reducing gases of hydrogen and reformed natural gas, so that the velocity of the gas at the reaction temperature was sufficient to entrain and pneumatically transport the solids through the coil. Reduction is very rapid with retention time of the ore in the coil varying from 4 to 15 seconds. Variables affecting reduction are temperature, ore feed rate, and gas flow or velocity. Results of the studies show that a partially reduced product (10-to 25-percent reduction) can be made which, on subsequent magnetic concentration, yields a concentrate containing 64 to 70 percent iron with a 90-to 94-percent iron recovery. Maximum reduction of 77 percent was obtained when hydrogen was used in a four-stage reduction test to yield a product containing 61 percent metallic iron.

Jan 1, 1972

By L. B. Pankratz

Low-temperature heat capacities, high-temperature enthalpy increments, and the enthalpy of formation at 298° K were determined calorimetrically for vanadium subnitride (VN0.465). The low-temperature investigation gave S°298.15 = 6.379 ±0.005 cal/deg mole, and a combustion calorimeter investiga¬tion provided ?Hf°298.15 = -31.80 ±0.60 kcal/mole. The two quantities were combined with the high-temperature data to give standard values of enthalpies of formation and free energies of formation above 298° K. These and related thermodynamic functions were tabulated to 1,800° K. Similar data are included in the range of 298° to 1,600° K for the mononitride, VN.

Jan 1, 1971

By S. P. Sandoval, A. E. Clark, S. W. Yopps, J. S. Gomer

The U.S. Bureau of Mines conducted Cu exchange tests for six common clays under simulated in situ leaching conditions. Regression equations were obtained from the data expressing the Cu exchange capacity as a function of Cu concentration, pH, and temperature. Using these equations, an analysis was made of the impact each clay could have on overall Cu recovery. The results suggest that Ca and Na montmorillonite clays could have a major impact on Cu recovery and that attapulgite and illite clays could have a smaller, but still significant, impact. Kaolinite and ripidolite clays pose little threat to loss of Cu from in situ leaching solutions.

Jan 1, 1992

By Rudolf Kudlich

"The realization that fuel costs, high as compared with those enjoyed prior to the war, are apparently permanent, has caused steam power plant operators to apply their best efforts towards improving the fuel economy of their plants.Though they have given much attention to the reduction in combustion losses by improving methods of firing and improved equipment, and to diminishing the heat losses by more care in maintaining clean heating surfaces and tight and adequate baffling, they have almost universally neglected the waste that occurs from discarding unconsumed combustible with the boiler refuse.This loss varies between extremely wide limits, depending on the quality of the coal, the type of plant and the firing practice in general, the higher the ash content of the coal the greater will be the amount of combustible appearing in the refuse, and the losses will be greater as the boilers are driven at higher ratings. The refuse from stoker fired boilers is apt to have a lower aver-eve percentage of combustible than that from hand fired boilers if operated at the same rating, but stoker fired boilers are usually pushed to higher ratings and the combustible in the refuse will run higher.In actual operating practice the amount of unconsumed combustible in the boiler refuse may range from a few percent to as high as forty or fifty percent. In an informal statement one well known combustion engineer estimates that the average amount of combustible in the refuse from a large stoker fired central station boiler plant is about 15 or 20%. Assuming that the coal burned contains 12% of ash, and allowing for flue dust losses, approximately two percent of the coal will be lost through this channel. The operating engineer of one large modern central power plant reports that when burning coal of about the same ash content, the average amount of combustible in the refuse was in the neighborhood of 33%, en tailing a loss of approximately 4% of the heating value of the fuel fired. Where the coal used daily runs up into hundreds of tons, an appreciable economy could be effected by recovering this percentage."

Sep 1, 1924

By Ernesto Villaescusa, Andres Brzovic

Rock masses of the primary copper ore at the El Teniente Mine are very competent and massive. The rock mass contains almost no open discontinuities. Nevertheless, there is a high frequency network of small discontinuities coupled with widely spaced faults. A data collection campaign designed to characterize the rock structure was recently implemented. The results show that conventional analysis in terms of discontinuity frequency does not predict differences between two studied sectors. However, when an empirical definition of a weak discontinuity is applied, appreciable differences between the two sectors appear in terms of discontinuity frequency and predicted in situ block size distributions. These differences are in accordance with actual observations at the mine site. Due to the geological features of the primary copper ore, rock mass classification schemes cannot be readily applied to characterize these rock masses.

Jan 5, 2007

By William J. Campbell

The Federal Bureau of Mines provided five test materials--amosite, short-and long-fiber chrysotile, crocidolite, and nonfibrous tremolite--to the National Institute of Environmental Health Sciences (NIEHS) for studies on the biological effects of orally ingested asbestos-related materials. An inter-agency agreement between the Bureau and NIEHS made possible this program to characterize these test materials. The Bureau in turn received support through contracts with the Ontario Research Foundation for the milling of amosite and crocidolite, and with the University of Maryland for microscopic measurements. The five test materials, which were supplied in quantities of 960 to 1,200 pounds each, were characterized by chemical-instrumental analysis for elemental composition, surface area, density, X-ray diffraction, infrared spectroscopy, thermogravimetric analysis, mineralogy, and particle size analyses. Particle size distributions were emphasized because of the current theories relating adverse biological effects to length-width characteristics of durable elongated particles.

Jan 1, 1980

By Seth C. Schaefer

As part of the Bureau of Mines, U.S. Department of the Interior, effort to provide thermodynamic data for the advancement of minerals technology, the Gibbs energy of formation of sphalerite (zinc sulfide) was investigated with a high-temperature galvanic cell employing stabilized zirconia as the electrolyte. In the temperature range 948 to 1,210 K, potential measurements were obtained for the cell Pt, ZnS + ZnO, S02 = 1 atm // Zr02 // Cu20 + Cu, Pt, with the overall cell reaction ZnS(c) + 3 Cu20(c) = ZnO(c) + 6 Cu(c) + S02(g). (1) These results, combined with the best available values of ?Gf° for ZnO, S02, and Cu20 from the literature, give the Gibbs energy of formation of zinc sulfide for the reaction Zn(l,v) + 1/2 S2(g) = ZnS© (2) ?Gf° = -64.223 + 24.02 X 10-3T ± 0.650 kcal/mole (3) (948-1,180 K; standard states - pure liquid zinc and S2 gas at 1 atm), and ?Gf° = -92.720 + 48.17 X 10-3 ± 0.650 kcal/mole (1,180-1,210 K; standard states - pure zinc vapor and S2 gas at 1 atm). A third law analysis yields for the formation reaction Zn(1) + 1/2 S2(g) = ZnS(c), (5) a standard enthalpy of formation as follows: ?Hf298.15 = -63.64 ± 0.700 kcal/mole.

Jan 1, 1978

To pinpoint dust sources and to improve dust control on longwalls. Approach Use short-term gravimetric sampling to determine the severity of various dust sources, and to evaluate dust control techniques used in longwall mining. Short-term gravimetric sampling can be used to isolate dust levels produced by various dust sources. How It Works Traditionally, gravimetric samples have been collected over an 8-hour shift, yielding time-weighted, average dust concentrations. This method gives a good indication of the full-shift respirable dust exposure of underground workers, but is less than satisfactory for identifying dust sources, determining their severity, or for evaluating the effectiveness of dust control techniques. Short-term gravimetric sampling uses equipment available to all mine operators. Two individuals composing the survey team each collect multiple (three to four) gravimetric samples during selected segments of the mining cycle. Multiple samples are necessary to insure accuracy, and to obtain a valid average measurement of the respirable dust concentration when sampling for short periods of time (typically 20 to 30 minutes). The gravimetric instruments may be carried in a sampling package or in a "sampling vest." A fishing vest with four large pockets can be used for this purpose. The sampling pumps are carried in pockets and the sampling head assemblies arc hung across the front of the vest.

Jan 1, 1982

To investigate mine ventilation problems which do not lend themselves to conventional anemometer and smoke study techniques by use of SF6 (sulfur hexafluoride) tracer gas. Approach SF6 tracer gas is released in-to the air at a given mine location. By collecting air samples at various other locations and analyzing these samples for SF6, the amount of air traveling from the release location to each sampling location can be quantitatively determined. Travel time between these locations can also be deter-mined. How It Works SF6 is ideal as a mine tracer gas. It is safe, odorless, chemically and thermally stable, and it generally has no background concentration. Furthermore, it is instrument detectable at concentrations as low as 10 parts per trillion. The SF6 is generally released from a pressurized lecture bottle, and air samples are taken in syringes or evacuated bottles. During the past several years, SF6 tracer gas has been employed to study a wide variety of mine ventilation problems such as: recirculation of return air into In-take airways, air leakage from adjacent mines and gob areas, air transit times through stoped areas, airflow patterns during a mine fire, leakage of gases from an underground oil shale retort into mine workings, face area ventilation patterns, methane flows in metal/nonmetal mines following a methane out-burst, and many other problem areas. Examples of some recent uses of SF6 follow.

Jan 1, 1982

A general analytical solution of the effect of an inclined contact separating two media of differing electrical properties on a normally incident plane electromagnetic field has been given (Geyer, 1972). These solutions for the electromagnetic response at any observation point P(r, [u]) are given in the form of inverse Lebedev-Kontorovich transforms. Two modes of excitation are considered: (1) case where current density flows across strike of the contact separating the media of differing electrical properties (only Er , E [u] , and Hx differ from zero) and (2) case where current density flows along-strike (only Hr , H [u] , and Ex differ from zero). The electromagnetic fields in the frequency range of interest and for the rock conductivities under consideration are quasi-static in nature so that to a first-order approximation the horizontal magnetic field at the surface of the earth is constant and continuous across the discrete discontinuity in resistivity for case (1) above, and so that the tangential derivative of the horizontal electric field at the surface of the earth is constant and continuous across the discrete discontinuity for case (2) above. Of course, it is well known that where large horizontal gradients in conductivity exist, there also exists large anomalous components of the vertical magnetic field (Weaver, 1963). The recognition of such anomalous components and their magnitudes due to the presence of lateral resistivity changes in the overburden becomes very important in any wavetilt type measurement which may be used to locate a miner. When the lateral change in resistivity becomes quite large, the integral solutions (expressed as Lebedev-Kontorovich transforms) simplify considerably and allow ready numerical evaluation. Examples of the amplitude and phase responses of the radial electric, horizontal electric, and vertical magnetic field in the vicinity of the contrast in resistivity are shown in Figures 2, 3, and 4. Of particular significance is the fact that the anomalous vertical magnetic field is three orders of magnitude larger near the contact than far from the contact. This fact implies that where large resistivity contrasts do occur in the rocks overlying mine workings, that significant errors may be present in wavetilt measurements as used above for location criteria! Another observation insofar as the anomalous vertical magnetic field is concerned is the linear variation of phase as one proceeds away from strike in induction number (increased distance or frequency). For a pulse-excited communications system this phenomena would have a bearing on where the zero crossings would occur (i.e., 'pulse breadth') in the transient coupling between any given source-receiver configuration and at any given receiver site.

Jan 1, 1973

By C. P. Bowie

[Frequent accidents in the transportation and. handling off petroleum and its more volatile products, serve as a reminder that this is indeed a hazardous undertaking and should always be conducted with due caution. On October 4, 1920, vapors in the held of the British tanks steamer G. R, Crowe became ignited and, caused an explosion which, it is reported, killed 5 men, injured. 40 others and endangered the lives of some 300 more. On November 10, 1920 the Morgan, Line freighter El Mundo was almost totally sot destroyed in New York harbor by fire caused by an explosion of gases in a fuel-oil tank. These two disastrous explosions emu emphasize the ever- present danger attending the use of petroleum products. This is also shown by the frequent occurrence of minor fires and explosions, caused by careless handling of baseline, which result in loss of life or serious injury to railroad employees, to oil-tank drivers, and to individuals in various walls of life. Statistics indicate that the lighter cuts of petroleum products, because of fire hazards, are dangerous, and are so considered by the railroad and other transportation companies. According o the Bureau of Explosives (Bar-eau of Explosives Report No. 13 p. 7) during 1919 transportation of gasoline in the United States resulted in 172 accidents, causing 2 deaths and 31 injuries, and a property loss to the extent of $687,966. Among the causes of ignition, an open light in the vicinity of the container stands out most prominently.]

Jan 1, 1920

By D. R. Flinn

The Bureau of Mines has studied the electrochemical parameters important to the preparation of coatings of the platinum-group metals. Using molten mixtures of sodium and potassium cyanides in an inert atmosphere, techniques have been developed that permit the preparation of baths for platinum, rhodium, and iridium electrodeposition. Cyclic voltammetric and slow sweep rate linear polarization techniques have been utilized to determine optimum potential and current values for preparation of plating baths and for the electrodeposition of coatings. Techniques are described for the deposition of platinum and rhodium coatings at near 100 percent anode and cathode current efficiencies, and for iridium at approximately 80-percent efficiency. Palladium deposition from these molten cyanide baths remains un-satisfactory. The chemistry of the palladium-containing cyanide bath is discussed. Examples of scanning electron microscope photomicrographs of typical platinum coatings are presented. Techniques are described for the preparation of platinum coatings on large objects.

Jan 1, 1982

By W. D. Walker

This information circular is offered to the coal-mining industry for use as a guide in selecting, placing, and caring for fire-fighting equipment in coal mines. Its purpose is to suggest minimum requirements for fire protection underground, and it is presented with the hope that it will aid in establishing adequate standards that will provide reasonable protection against underground fires in coal mines. Potentially, a coal mine is a hazardous fire area. Coal itself is a combustible substance, easily ignited. In addition, large quantities of other combustible materials must be present in the area of operations; these include materials for roof support, track ties, doors, ventilation stoppings, lubricants, etc.

Jan 1, 1953

This Bureau of Mines report on underground mine communications addresses methods and equipment to meet the communication requirements of working sections and places of coal and metal-nonmetal mines. A review of the status of trapped miner detection is also presented.

Jan 1, 1977

Objective As mines become safer and disasters fewer, a time may come when no employees in the mining industry have any practical experience in managing a mine emergency. To fill an emerging gap in mine emergency response training, a multidisciplinary team of researchers and computer programmers from the NIOSH Pittsburgh Research Laboratory has developed an intervention for mining personnel who would be in leadership positions in the command center during emergencies. It is called MERITS, a computer-based emergency simulation exercise. MERITS is short for "Mine Emergency Response Interactive Training Simulation." It provides trainees an opportunity to gain command center experience during a simulated underground coal mine emergency. MERITS allows trainees to practice information gathering, situation assessment, decision-making, and coordination skills without risk to personnel or property. Individuals representing mine emergency response personnel, various State safety officials, and private mine management from three States have participated in MERITS training. What Is MERITS? MERITS is an extension of previous work that compiled a knowledge base relevant to mine disaster management via interviews, analysis of literature, reviews of past events, and observations of mock mine disasters. Findings from prior research found a need for an alternative method of command center training. This new computer simulation is being used to train emergency command center personnel to effectively manage an underground mine fire. Modeled after training simulations developed for other industries (e.g., to address nuclear accidents, chemical spills, evacuations, etc.), MERITS simulates underground and surface events related to the disaster. It exposes the user to events that typically occur during a mine emergency, such as lack of information and miscommunication. It also presents trainees with issues that must be addressed, such as making provisions for briefing news media and victims' families, ordering needed supplies, interfacing with Government enforcement agencies, and housing mine rescue teams. The outcome of the scenario is determined by the users' decisions and their emergency response plans. Field Results Field testing of MERITS was conducted with eight full-day training sessions at four different locations in Colorado, Pennsylvania, and West Virginia. These field tests benefited from the knowledge and experience of State of Pennsylvania inspection officials, representatives of the United Mine Workers of America(UMWA), and private mine management who served as trainees for the MERITS training sessions. Trainees self-reported an average of20 years of work experience in the mining industry. All trainees had participated in Mine Emergency Response Development (MERD) training exercises, and many had been involved in real mine emergencies. Trainee evaluation of the MERITS program is summarized below: •Twenty-six of the 27 trainees believed that the MERITS simulation helped them know how to prepare for a real emergency. •Twenty-five of the 27 trainees believed that the storyline for the MERITS simulation was either "very realistic" or "realistic." •All 27 trainees believed that the MERITS simulation helped them learn how to better handle a real emergency. •None of the 27 trainees stated that they were bored during the simulation. After the initial field tests, MERITS was refined and retested during training sessions for individuals from State agencies, the UMWA, and private industry. Mining personnel from underground coal and underground stone mines participated and responded positively to the learning experience. Technology Transfer Industry introduction to the MERITS program will occur throughout 2002. MERITS presentations at the Joseph A. Holmes Safety Association National Meeting in Virginia Beach, VA, in June.

Jun 1, 2002

By Donald P. Schlick

This report presents a representative cross section of methods success- fully used to ventilate continuous-miner places as well as various factors that should be considered when selecting auxiliary ventilating equipment. Line brattice can direct fresh air to the active face reasonably well, provided that adequate area for installation is available. Continuous mining equipment, however, often restricts clearances to such an extent that proper installation of line brattice is impossible. Consequently, in many instances face ventilation is inadequate; therefore, many methods of auxiliary ventilation for continuous-mining equipment have been developed and have been discussed in this study.

Jan 1, 1963

By Bill M. Stewart, Phil W. Patton, Curtis C. Clark

Back injuries from handling materials in underground mines continue to be a major safety problem. In spite of the ingenuity of many people and the development of numerous mechanized aids, the number of materials-handling injuries remains second only to the number of roof fall injuries in underground coalmines. Relocation and repositioning of electrical cable, conveyor belt parts, and roof bolt sup-plies in particular are the sources of significant numbers of back injuries. To help reduce such injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are examining Mine Safety and Health Administration accident data to determine correlations between materials-handling tasks and the number of back injuries. Also being investigated are new technologies used in underground mines in the United States. Equipment is being developed or modified that would replace the necessity of doing lifting tasks manually. A Coleman manipulator was tested, and modifications were made to make it more suitable for underground mine use. To reduce or eliminate the need to manually clean off materials that commonly plug grizzly openings, a track-guided pincher arm device was developed. Oversized rock can be broken with the pincher arms in the up position, and the arms can be lowered to grab and remove debris. The arm can also be used in a sweeping action to remove cohesive fines that may bridge grizzly openings.

By Lloyd A. Morley

This report abstracts project work performed under USBM Grant GO155003 during the period 4 November 1975 to 3 November 1976. The research was funded, as a continuance of previous support from USBM Grants GO133077 and G0155003, to gain further knowledge in mine electrical system safety. Five reports have been separately produced, all under the grant title, "Coal Mine Electrical System Evaluation," and are as follows: 1. Volume I - Continuous Monitoring, 2. Volume II - Transient Analysis, 3. Volume III - Shielded Cables, 4. Volume IV - Computer Modeling, and 5. Volume V - Battery and Battery-charging Safety. Abstracts of these comprise the balance of this document with one exception. The task ?d-c offsett currents," does not fall under the scope of the other report volumes and, further, the material to be presented does not justify a separate report. Hence, this subject concludes the Executive Summary.

Jan 1, 1977

By R. Pakalnis, Richard P. Curtin, Lewis A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control to monitor rock mass loads at various field sites (FMC Granger, Getchell, Meikle, SSX, K-2, and Stillwater). Axial and shear loads were determined by strain gauges to levels of instrument accuracy of ±5 N or ±5 microstrain as these loads were transferred to the instrumented cable bolts. These gauges were 12.5 mm long and embedded into are manufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. By monitoring load on and displacement of the rock mass, more effective ground support can be selected and installed, which will lead to safer working conditions for miners.

By Wallace W. Roepke

The Bureau of Mines has a well-established health and safety research effort directed to fundamental studies of the mine cutting system. This report describes the ignition danger of using cutting bits with flat wear area on still-intact carbide inserts.

Jan 1, 1983