Search Documents

By J. L. Johnson

The U.S. Bureau of Mines investigated the recovery of tin and silver from the Coal Creek deposit in the Talkeetna Mountains, AK. Approximately 5 million st of reserves grading 0.2 pct Sn with silver credits of 0.2 tr oz/st have been delineated by drilling. A 10-to 25-pct Sn gravity concentrate was produced by treating the minus 20-mesh ore with a spiral, then regrinding to minus 65 mesh and tabling. Sulfide contamination in the gravity concentrate was as high as 60 pet. Sulfide flotation of this concentrate produced tailings containing 40 to 50 pet Sn. Overall recovery was 76 pct for tin but only 5 to 10 pct for silver because of losses during sulfide flotation. Other methods tested to clean the concentrate included cassiterite flotation, gangue flotation, nitric acid leaching, and wet and dry magnetic separation. Tin beneficiation tests on the minus 325-mesh fraction included cassiterite flotation, vanning, sulfide flotation, and fuming. The bench-scale and locked-cycle tests were used to estimate the mass flows for a 1,000-st/d plant.

Jan 1, 2010

By Anil Mahyera

This report present the results of a laboratory and field research program aimed at design and development of a torque-thrust controlled bolter with the capability to (1) predict the "quality of anchorage" attained while installing mechanical anchor roofbolts, and (2) improve the uniformity and tension levels achieved among a group of roofbolts. The prediction accuracy of the anchorage quality algorithm ranged from low to moderate because of the complexity and variability of the phenomena involved. The best roof support with mechanical anchor bolts was found to be achieved by simply installing them under ? proper torque-thrust control, and with ? a hardened washer under the bolthead. This procedure resulted in an improvement in uniformity of 3 times, along with an increase in mean tension levels of 75% over conventionally installed roofbolts.

Jan 1, 1983

By Diana K. Schimmelpfennig

Assessment of revegetation success on mined lands is a difficult, time consuming task and has been the subject of a number of controversies. Present regulations require that both plant cover and aboveground plant biomass be measured for use in making that assessment. Of these two variables, biomass is the most time consuming to measure and requires destructive sampling, a most undesirable requirement on fragile, recently revegetated areas. On the other hand, plant cover can be estimated using the point-frame method which is relatively nondestructive. In addition, vegetation can be sampled more uniformly with the point frame and in less time if species composition measures are to be made. A study was done to evaluate the predictability of aboveground biomass production on revegetated mined sites and adjacent native prairies using plant cover estimates made with the point frame method. The predictability of biomass production by cover estimates bears on the need for both measurements in assessing revegetation success. In general, a positive, statistically, significant correlation was demonstrated between plant cover (estimated by the point frame) and aboveground biomass (estimated by the harvest method) regardless of community type (mined or native), species composition, diversity or level of biomass production. However, the latter did have their effects on the relationship and must be accounted for in any predictive equations (that is to say, the predictive equations must be considered site-specific). Considering the relationship observed between the two parameters, cover estimation may be a sufficient indicator of revegetation success, especially where time and minimization of disturbance are critical.

Jan 1, 1982

By H. M. Smith

Data from the Bureau of Mines routine method for the analysis of crude petroleum are used to characterize crude oils. Some data are used directly while other data are used to calculate the aromatic) naphthene) and paraffin contents of the distillation fractions and the correlation index of the paraffin-naphthene portion of the fractions. The calculated properties show significant differences in composition between crude oils. The methods of calculation and interpretation of data are explained and illustrated.

Jan 1, 1966

By G. B. Atkinson

The Bureau of Mines investigated a method for increasing the leaching rate of bulk superalloy scrap to facilitate recycling and recovery of critical metals such as Ni, Co, and Cr. Three superalloys were investi- gated, the cast-nickel-base superalloy IN-738, the wrought-nickel-base superalloy Rene-41, and the cast-cobalt-base superalloy Mar-M-509. Superalloys melted with 20, 30, 40, and 50 pct Al metal to form inter- metallic compounds were easily crushed to a convenient particle size and reacted rapidly with acid solutions which dissolved the metals. For example, leaching 1/2-in pieces of unalloyed IN-738 with excess 6N HC1 at 95° C for 2 h dissolved about 0.5 pct, while leaching 10 g of minus 20-mesh 30 pct Al-70 pct IN-738 with excess 6N HC1 at 95° C for 2 h dis- solved 96.2 pct.

Jan 1, 1983

An accelerated and coordinated program of coal research is believed by many to be a necessary step in assuring coal's proper position in the expanding energy market. The President's Advisory Committee on Energy Supplies and Resources Policy, for example, made the following recommendation: We recognize that coal is a great national asset and endorse a cooperative study to determine what research and development could be undertaken. The coal industry and both Federal and State Governments should participate in this study and its costs. Representatives of the coal industry have agreed that such a study should be initiated. Accordingly, Felix E. Wormser, Assistant Secretary - Mineral Resources, United States Department of the Interior, requested the Bureau of Mines and Bituminous Coal Research, Inc., to conduct a survey of current research on bituminous coal. In addition to this survey, studies were made to determine research projects that would be of value to the coal industry.

Jan 1, 1956

By B. J. Arnold, F. F. Aplan

"The captive bubble and sessile drop contact angle techniques have been used to evaluate the hydrophobicity of petrographically identified coal macerals. The magnitude of the contact angle on vitrinite is shown to be a function of coal rank ( %C, %0 and % vitrinite reflectance), increasing with increasing rank to a maximum for low volatile bituminous rank coals then decreasing for anthracite. The least data scatter is found when vitrinite reflectance is used as a rank parameter. Contact angles measured or estimated for other discrete macerals, indicate a variation in hydrophobicity based on coal type. These data correlate well with known flotation results. Coal is a heterogeneous mixture of plant remains and associated minerals that have undergone chemical and physical changes by biological and geological processes. These plant remains form coal macerals, discrete organic entities in the coal which have characteristic chemical and physical properties. As the differing chemical nature of each maceral will affect its behaviour in processes such as carbonization the separation of macerals during coal preparation may provide an important asset in coal utilization.Separation of some of the macerals based on specific gravity has been achieved in the laboratory, and by Sun and Cohen , in a study of two Pennsylvania bituminous coal preparation plants. It was indicated that the lighter exinites report almost exclusively to the clean coal while the denser inertinites are concentrated in the higher gravity fractions. The Longwy-Burstlein process6 took advantage of the difference in hardness or friability of the macerals by using impact breakage followed by screening to remove the more friable vitrain,clarain and fusain. The remaining durain, often high in spore content, was then recrushed. The re-mixed fractions produced the optimum size for obtaining the best coke strength for a particular coal.Separation or concentration of rnacerals by froth flotation largely depends on differences in the hydrophobicity of the macerals. Sun and Cohen 5 . indicated an order of decreasing floatability as exinite, vitrinite and inertinite, while a Russian study (as cited by Brown 7 ) showed that vitrains floated more readily than the duller types. More recently, Hirt and Aplan8 showed that 'pseudovitrinite' floats somewhat faster than does vitrinite while fusinite floats very slowly. Olson and A plan found that vitrinite floated easily while substantial quantities of the non-floated coal contained fusinitic material. Burdon noted that vitrinite is more floatable than semifusinite, and Sarker et a/. 11 have shown that vitrinite is selectively concentrated by froth flotation and oil agglomeration. Sun indicated that flotation, based on his calculated floatability index, should decrease in the order clarain, vitrain, fusain and durain; while Horsley and Smith 13 indicated the decrease to be: vitrain, clarain, durain and fusain. These differences can be attributed to the specific coals used in each study and to the individual macerals composing each coal type within a given coal."

Jan 1, 1989

By F. S. LOTT

Publication of the Bureau of Mines annual surveys of the capacity of petroleum refineries in the United States was suspended after the entry of the United States into World War II . The last published survey was that of January 1 , 1941 , released in April 1941 as Information Circular 7161 . The purpose of this publication is to provide comparable information with respect to crude - oil and cracking capacity on January 1 , 1947. No attempt is made at this time to bridge the gap in annual statistical series from the date of the last published survey to the present one . However , complete summary tables will be included in the succeeding survey for January 1 , 1948 .

Mar 1, 1948

By R. A. Guereco

Accurate measurements of physical dimensions of a section of stainless steel capillary tubing are presented and used to develop two final working equations for an absolute gas viscosimeter. The effects of pressure and temperature on these dimensions are considered. The internal surface finish and nonuniformity of the capillary bore are discussed, as well as entrance, kinetic energy, gas slippage, and gas compressibility correction factors.

Jan 1, 1967

By Ronald T. Mayerle

In 1989, the U.S. Bureau of Mines conducted a mineral investigation of the Mallard study area near Elk City, Idaho. The study area comprises most of the original Mallard RARE II area (1-847) plus some additional lands. The investigation is part of an ongoing, multi-year study of north-central Idaho that is being conducted in cooperation with the Idaho Geological Survey and the U.S. Geological Survey (USGS). The only identified resources are rock suitable for road metal. Five lode prospects and a pyrite-bearing rock quarry, which is operated by the Forest Service for aggregate, were examined for metals. One of the prospects warrants additional exploration for silver in quartz veins, but the chance of finding an economically minable deposit is limited. Several rock and stream sediment samples were anomalous in various metals. Two of the more promising localities for gold and/or other metals are adjacent to a unit of the Frank Church-River of No Return Wilderness that the USGS classified as having a moderate potential for gold deposits related to fossil hot springs.

Jan 1, 1991

By Wesley A. Grosh

The Valzinco mine, Spotsylvania County, Va., is a lead-zinc deposit with minor quantities of copper. The property was reopened n 1942 by Panaminas, Inc. The Bureau of. Mines, in an effort to increase the reserves of the deposit to justify greater production, diamond-drilled nine holes totaling 4,213 feet during 1943. Drilling by the Bureau delimited the original ore body and discovered another ore body on the hanging-wall side, which was being developed by the company at the close of the project.

Jan 1, 1949

By R. F. Droullard

The Bureau of Mines has developed test facilities for use in a research program that deals with radiation hazards in mining. This report describes the radon test chamber located at the Denver Research Center and the Twilight experimental mine located near Uravan, CO.

Jan 1, 1984

By N. H. Darton

In mining coal in the anthracite region of Pennsylvania the general custom has been to leave a large percentage of the coal in place as pillars to support the roof. Evidently any practice that involves partial waste of an important mineral resource is bound to be discarded. It is well recognized that one method of obviating probable waste is to fill the workings with cheap or worthless materials, a process extensively employed in the anthracite and some European mines. At present many of the collieries in the anthracite region of Pennsylvania are utilizing refuse from the old culm banks, which formerly were prominent features in the landscape, and are flushing the fine waste underground so that pillars may be reduced in size or removed. As a result the banks are now disappearing and soon will be gone. The fine culm from the breakers and rock from the mines will continue to be available, but the volume of these materials is insufficient to replace any considerable proportion of the coal removed. The next stage of progress suggested is the use of sand. Fortunately there are available large deposits of this material, much of which can be handled by dredges and pumps. This report is issued by the Bureau of Mines in the interest of safer and more efficient mining methods. I ts purpose is to describe the sand deposits in the northern anthracite coal field in Luzerne and Lackawanna Counties, Pa, Much of the information available is presented in the map, Plate I. Field studies, mostly preliminary, were made in the summer of 1911 to determine the distribution, amount, and character of the larger deposits. It was not thought desirable to make a detailed examination of the region because when the coal companies decide to utilize the sand their engineers will make precise surveys and drill test holes. In preparing the map the various coal companies were consulted; they contributed a large number of facts, especially as to the deposits in the buried valley of the Susquehanna between Pittston and Nan- ticoke, where nearly 1,000 test holes have been bored. The results of these borings were placed at the author's disposal, and have been utilized in drawing the boundaries given in the wide valley area and its extensions up Lackawanna River and NewportCreek. Wyoming Valley contains deposits of sand that are 100 feet thick over a wide area, 200 feet thick in places, and over 300 feet thick in the deep old channel south of Plymouth.

Jan 1, 1913

By Craig M. Jensen

A laboratory assessment of prompt and delayed neutron activation analysis with 252Cf and 14MeV neutron sources, for use as an in-situ method of determining low-level copper concentration has been performed. A simulated borehole using porphyry ore was constructed and varying copper concentrations were simulated using copper rods. Prompt neutron activation analysis experiments were consistant with earlier work and do not appear to be feasible fur copper concentration of 1.5% or less. Delayed neutron activation analysis experiments indicate that copper ore concentrations of less than 0.1% are detectable using either the 511-KeV gamma-ray of copper-64 or the 1039-KeV gamma-ray of copper-66, with high resolution detectors such as Ge (Li) or intrinsic germanium.

Jan 1, 1977

By E. J. Matson

The Table Mountain copper deposit is in an isolated portion of north-eastern Churchill County, Nev. Although copper-bearing outcrops have been known to exist in the area since 1909, no copper ore has been mined. Development of the property has been hampered by poor roads and rugged topography. Until 1941, the last 4 or 5 miles to the property had to be traveled either by foot or pack animal. As a part of the Bureau of Mines program of investigation and development of domestic mineral deposits, a project was started at the Table Mountain deposit. The Bureau began its field work on July 29, 1947, and completed it on October 18, 1948. Thirteen holes aggregating 2,711 linear feet, were drilled; samples were analyzed - 509 from cores and 143 from sludges. This report contains a brief history of the district and a description of the geology, deposits, and drilling done by the Bureau.

Jan 1, 1949

By Louis C. Brichta

The Kline tract ?3.nd the Frey tract are two separate properties situated in the Wentworth district on the easterly edge of the Tri-State zinc-lead region (fig. 1). The Kline tract is in the southwestern corner of Lawrence County, Mo., and the Frey tract, 1 1/2 miles west of the Kline, is in the northeastern part of Newton County, Mo. A bureau Of Mines drilling project embraced work on both properties, but the amount of work done on the Frey tract was comparatively small. At the time of the project the Kline tract was under lease to the Wentworth Mining & Milling Co. The Surprise Mining Co. held the lease on the Frey tract. Underground workings on the generally flat-bedded are deposits of the Kline property-covered an area of-about 15 acres. No total metal-production records are available. In 1942-1943 the mine, operated by the Wentworth Mining & Milling Co., produced at an average monthly rate of 83 tons of 60-percent zinc concentrate derived from mining and milling 1,700 to 2,100 tons of ore. At the end of that period no significant amount of reserve ore was in sight. The gravity-flotation mill on the property was operating at about one-sixth capacity.

Jan 1, 1949

By Steven A. Fechner

In 1991 and 1992, the Bureau of Mines completed chromium, platinum-group metals (PGM), and tin investigations, and started indium, manganese, titanium, and vanadium investigations in Alaska. These studies were done as part of the Site Specific Minerals Investigations project. As a result of this work, the Bureau found PGM-bearing composite plutons in the Yentna River area of the Alaska Range, which are chemically similar to composite plutons in other parts of the Alaska Range and to Ural-Alaskan type complexes. Previously unknown chromium and PGM occurrences were found in the western Brooks Range. A compilation report on the Bureau's chromium and PGM investigations in the western Brooks Range was also published. Indium was found in anomalous concentrations at the Lost River tin deposit. Small occurrences of manganese were located, mapped, and sampled in the Wiseman and Chandalar quadrangles, and in the Liberty Falls, Prince William Sound, and Homer areas. Tin occurrences in western Alaska were summarized in three Bureau open file reports. The beaches near Cape Yakataga and Yakutat were evaluated for their titanium potential and a sampling methodology was developed. Vanadium investigations included examining streams in the Wiseman and Eagle areas that contained anomalous vanadium values. In the Eagle area, high vanadium, uranium, and copper values were found in the basal layers of the Road River formation.

Jan 1, 1994

By William H. King

The Mercur Dome mine is in the Camp Floyd mining district, Tooele County, Utah (fig. 1). The property lies between 6,000 and 8,000 feet altitude on the southwesterly slope of the Oquirrh Mountains, a short distance west of Mercur, the district settlement. Mining began in the Mercur area in 1870. Operations at the Mercur Dame mine were started in 1937 after several claims had been consolidated into one group. Preliminary examination of the ground by F. H. Gunnell, a Bureau of Mines engineer, disclosed the presence of vanadium in a carbonaceous shale horizon. Rocks near the Mercur Lame property are chiefly sediments of Carboniferous age, including the Madison and Deseret limestones. The main shaft penetrates the Deseret formation to a point a few feet above the 1,000-foot level where it enters the Madison limestone. The flat-lying vanadiferous shale horizon is exposed on the 1,000-foot level near the top of the Madison limestone. The Bureau of Mines development program, consisting of diamond drilling, auger hole drilling, and sampling, was planned to determine the extent and assay value of the vanadiferous bed. Seven diamond-drill holes totaling 300 feet were drilled from the 1,000-foot level of the mine. Eight hand auger holes were drilled in the back of the drift on this level (fig. 2). Assay determinations were made on 74 samples from the drill holes and supplemental channel samples and are tabulated in this report. The concluding section embodies results of metallurgical tests.

Jan 1, 1949

By H. Kim, R. W. Plummer, T. J. Stobbe, W. G. Jones

"Exposure to airborne dust in coal mines has caused respiratory disease in coal miners. The causal agent in these diseases remains unknown, although the minerals found in and around the coal seam have been implicated. Toxicological studies designed to establish the effect of different mineral combinations and concentrations are lacking because the mineral content of coal mine dust has not been defined. This paper reports the initial results of a study done to characterize the mineral content of the coal mine dust found in a mine in the Upper Freepott seam in Northern West Virginia. Coal mine dust samples were collected using 4- stage cassette impactors at nine locations in the mine. The samples were analyzed by an x-ray microdiffraction film technique supplemented by energy dispersive scanning electron microscopy. Primary size modes of about 17 to 20 micrometers from the samples collected at the haulageway and the returnside of the continuous miner were found. From the returnside of the roof bolter samples, a primary size mode of 12to15 micrometers was measured. The minerals found in high percentages were illite, kaolinite, quartz, and calcite. The distribution of minerals in inter· and intra- location samples showed wide variations. Trends in these variations are presented. Stobbe, T. J.; Plummer, R. W.; Kim, H.; Jones. W.: Characterization of coal mine dust. Appl. Ind. Hyg. 2:95· 100; 1986. IntroductionDisease-associated dusts in coal mine environments continue to afflict miners in today's modern mines. The relationship between exposure to coal mine dust and the development of various respiratory diseases has been well recognized; however, the reasons for variation in occurrence of these diseases among miners in different geographic areas,(1) rank of coal seams,(2-3) and jobs (4) remain uncertain. Several papers have reported on the causal agent in the development of these diseases. Davis (5) found that the percentage of the non-coal minerals present in the lungs of deceased miners increased as the level oi pneumoconiosis became more severe. Reisner (6) reported that cell damage caused by coal mine dust increases with the mineral and quartz content of the dust and with the geo· logical age and rank of the coals. Two studies, investigating the in vitro effects of mineral dusts. reported by Seemayer and Manojlovic (7) also obtained positive correlation between cytotoxicity and the mineral content of coal mine dust. Gormly (8) postulated that destruction of macrophages by certain mineral dusts is the first step in the development of pneumoconiosis. In 1980, Adamis and Timar (9) reported that quartz. sandstone, slate. respirable colliery dust. bentonite, illite, and some kaolins had cytotoxic effects on rat peritoneal macrophages""in vitro."" Walton,(10) however, reported that the presence of high clay, illite, and kaolin mineral exposures reversed the hazards associated with increasing quartz exposures. This finding was supported by Le Bouffant and coworkers.(11) They reported that illite present in coal mine dust strongly inhibited the pathogenic effects of quartz while kaolin had a weaker inhibitory effect."

Mar 1, 1989

By Richard C. Wang

The U.S. Bureau of Mines established a wire rope research laboratory to examine the factors that affect the safety and the useful life of wire rope. In the most recent work, two 32-mm 6x27H flattened strand ropes were degraded on a bending fatigue machine. The two tests were run at constant loads of 285 and 347 kN or safety factors of 2.5 and 2. Nondestructive and tensile strength tests were performed on samples of the ropes to determine the relationship between rope deterioration and rope breaking strength. Neither the area loss nor the number of broken wires measured from nondestructive tests could be used as clear indicators of the loss of strength. However, it was found from the tensile tests for both rope specimens that the strength loss was associated with the reduction of breaking strain. This suggests that measuring the strain of many short sections of a rope in the elastic region may locate the high stress sections and thus delermine the condition of the rope.

Jan 1, 2010