Search Documents

By Babu K. V., Samyukta P.

The energy demand in India is expected to show increasing growth in the next few decades. The oil companies in India are revamping the existing oil refineries as well as constructing new refineries across the country to meet the energy demands. Most of the refineries in India are located along the coastal region because of the ease of transporting crude materials. Considering the criticality of the structures as well as soil conditions in the coastal region, pile foundations are used in refinery plants. In India, non-displacement piles in the form of bored cast-in-situ piles are used to support structures. In a few circumstances, displacement piles in the form of driven cast-in-situ piles are also being used to support critical structures. This study presents the performance of non-displacement and displacement piles for similar ground conditions at the same project location. The pile load test results have shown that the settlement observed for displacement piles is lower than compared to non- displacement piles for a given loading and soil conditions. This shows that the performance of displacement piles is slightly better in comparison with that of non-displacement piles.

Sep 1, 2022

By Suresh Chikati, Gangadharan Santhanam

Twin tunnels were constructed to a length of 863m using TBM in one of the underground metro projects. The tunnels pass through complex geological conditions (soil, rock and mixed conditions). This paper presents the consideration of volume loss and the corresponding ground settlement associated with the excavation of twin TBM tunnels by analytical and numerical methods. Empirical methods were used to calculate the ground settlement induced by the excavation of twin tunnels. The ground settlement values were directly derived from the two parameters: the volume loss and trough width parameter. These parameters are calculated based on the geological conditions at the tunnel face and tunnel overburden. The finite element software, Plaxis 2D was used to model the soil parameters with appropriate geological conditions. Twin tunnel excavation is simulated in Plaxis 2D and the effect of tunnelling on the ground was simulated by percentage volume loss. The suitable line contraction value was applied to the tunnel linings to simulate the volume loss. The surface ground settlement was directly obtained from Plaxis 2D. Instrumentation arrays were proposed along the twin tunnel alignment, to provide the ground settlement monitoring data within the influence zone of tunnelling activities. The derived ground settlement values from analytical and numerical methods were compared with the actual field instrumentation and monitoring data. From the field instrumentation data, the actual volume loss values were calculated. The compatibility of ground settlement and volume loss calculated using analytical and numerical methods and those measured using field instrumentation data is discussed in this paper.

Sep 1, 2022

By Ryan Weaver, Travis Coleman

The drilled shafts that support transmission lines and substations have been increasingly subject to testing to assess the integrity of placed concrete. Cross-hole Sonic Logging (CSL) has been used, but large diameter shafts with challenging site access are generally more favorable to Thermal Integrity Profiling (TIP) testing. TIP testing assesses the shafts based on measurements of the concrete temperature during curing. The TIP results provide assessment of integrity both within and outside the cage, along with information about the alignment of the cage and concrete cover. This data has allowed shafts with imperfect results to be subject to more detailed structural evaluations. However, it may not be well understood how to use this additional information by designers and engineers. The purpose of this paper is to present TIP results of transmission line foundations, both with and without issues with integrity, including cage shifting, minimal concrete cover, or soil inclusions. The intent is to provide general guidelines of the issues that merit additional investigation and those that should be recognized as inconsistencies inherent to underground construction. BACKGROUND This paper is intended to discuss some of the drilled shaft evaluations made when TIP testing is performed. The authors of this paper were recently involved with a transmission line project that was designed and constructed for a Confidential Utility Client located in the Midwest United States. The project was delivered as an Engineering, Procurement, and Construction (EPC) contract with the electrical line construction company as the prime contractor. The contractor then subcontracted several parts of the work which included engineering for transmission line and foundation design, foundation construction, and third-party testing intended to evaluate the concrete homogeneity and integrity of the place concrete in the deep foundations. The testing method selected was Thermal Integrity Profiling Method B, which uses thermal sensors embedded in the concrete. The TIP testing was administered by Mr. Travis Coleman with GRL Engineers, Inc. Mr. Ryan Weaver with Burns & McDonnell served as the owner’s engineer and technical consultant for the utility and was responsible for reviewing submitted TIP reports and providing recommendations to the utility on their acceptance, and if there were any issues that would warrant further discussion and analysis.

Jan 1, 2019

By Dale Berner, Michael O’Sullivan

"This paper focuses on lessons learned from the innovative designs, in-the-wet construction methodology and modified foundation conditions, for two United States Army Corps of Engineers, USACE, Megaprojects:(a) The over $2 Billion Olmsted Dam across the Ohio River for the Louisville District; and(b) The $1.75 Billion Inner Harbor Navigation Canal, IHNC, Lake Borgne Hurricane Barrier in New Orleans for the Hurricane Protection Office, and the New Orleans District.Design innovations for the 24-inch dia. pipe pile foundation for the Olmsted Dam project include: (i) the use of controlled-fixity moment connections to the dam monoliths in order to tune the response of the dam under the 8.3 Richter scale seismic Maximum Credible Event, MCE; (ii) soil densification to inhibit liquefaction potential and (iii) design to facilitate underwater construction in a river with a highly moveable sand bed.Design innovations for 66-inch dia. concrete cylinder piles for the IHNC floodwall include: (i) the use of soil structure interaction, SSI, analyses to verify capacity to resist deep-seated failure plane in soft soil, while limiting lateral deflections to acceptable limits; (ii) the use of geo-fabric and scour stone for enhanced foundation response and (iii) design for ""in-the-wet"" construction on a fast-track basis.LESSONS LEARNED FROM THE INNOVATIVE OLMSTED DAM FOUNDATIONThe over $2Billion Olmsted Dam on the Ohio River is currently under construction 16 miles upstream from the confluence with the Mississippi River. It will consist of an 800-foot-long tainter gate section, a 1,400-foot navigable pass, two boat abutment sections, a fixed weir section, and upstream and downstream scour protection. The Olmsted Dam and its two, 1,200-foot locks, which were built in 2002, will eventually replace both Locks and Dam #52 and #53, both built in 1929, and thereby bring significant benefits to the Ohio River navigation system.In 2002, the Jacobs/COWI JV completed the design of the dam; which was an engineering challenge for several reasons, including:(a) Its proximity to the New Madrid Fault, could impose an 8.4 Richter Scale seismic event on the structure, which is located in an area of potentially liquefiable alluvium. The extensive seismic analysis performed by COWI included a response spectra analyses; lateral pushover analyses of pile foundations; hydrodynamic added masses; pile group effects; and the development of kinematic motions as a result of the soil-pile-structure interaction.(b) Maintaining vessel traffic along the river and accommodating fluctuating river elevations between 30-40 ft annually, and as much as 60 ft in a 100-year period.(c) Designing for the scour and uplift forces of artesian ground water and preserving a wildlife sanctuary on the Southern shore at the dam site."

Jan 1, 2017

By Pathik Deb Mallik, Shyamal K. Mitra, Rajiv Kishore, Shuvranshu Rout, Manos De

"This paper presents a case study on the design and construction of a deep underground pit structure constructed inside almost a century old existing plant building. The complexity and challenge for the design and construction lay in executing the work in a difficult subsoil condition especially the presence of deep mica schist. The limited space availability in the existing plant for construction work without hampering regular production in other adjoining areas of the plant made the execution more challenging. Experience with difficult subsoil and proximity to old foundations entailed a non-conventional engineering approach while ensuring complete safety in spite of maintaining the normal operation.INTRODUCTIONTata Steel Processing and Distribution Limited (TSPDL) is a subsidiary unit of Tata Steel Limited (TSL) having a CR processing facility inside the premises of Tata Steel Limited. TSPDL intended to install equipment for a new slitting line inside the existing shed including construction of very deep structure called “loop pit” where the strips from cut CR sheets collect in the form of loops and are recovered as scrap. The entire plant is located within the shed of existing plant. The construction of all foundations including the loop pit is to be executed in the limited area without disturbance to normal production work in balance areas of the plant and also maintain safety and integrity of existing structures.The existing shed is an old structure constructed approximately 80 years ago. The building column foundations are gravity type design of brick masonry supporting only the vertical load from the columns. This type of foundation designed with no eccentricity of loading provides no allowance for implementing any foundation stabilizing design. The present project required civil construction for the new equipment foundations safely within this area."

Jan 1, 2015

By Rajasekar Subbian, Jessica Oudhof

In the Netherlands pile foundation design is done using CPTs in accordance with EC7 national annexure. The capacity per tip level is calculated for every CPT followed by zonation to find the tip level per zone. The correlation factors are used to take into account the variability in ground across the zone and they depend upon the number CPTs within the zone. The CPTs and pile tip levels selection for zoning is an iterative process that can demand significant manual effort to produce an economical pile plan. This often leads to the use of conservative correlation factors in order to accelerate the design process. Thus, it has been automated in a tool with CPTs, pile location and loads, and capacities as input. The tool has also been employed in two case studies and the results are compared to the current design practise.

May 1, 2022

By Suthan Pooranampillai

Verification of drilled shaft resistance is primarily obtained through the use of different load testing methods. Procedures utilized include conventional top down static loading, the Osterberg load cell (O-cell) test and dynamic tests such as the Statnamic method. The O-cell test provides a means of obtaining separately the base and side shear resistance behavior of drilled shafts (cast-in-drilled-hole). Alternatively, the Statnamic load test method enables the engineer to derive base and side shear behavior separately, based on measurements of load, accelerations and strains along the length of the shaft. However, due to time and cost constraints these tests can only be performed on selected shafts within a project. Post grouting of a drilled shaft base embedded within a cohesionless material, with a low mobility compaction grout, will essentially pre-load the shaft base soil against the side shear and self-weight in much the same manner as an O-cell load test (when the load cell is placed within the base vicinity). Therefore, successful post grouting of a drilled shaft would enable verification of both shaft side shear and base resistance simultaneously on each and every shaft it is carried out on. Additionally, such post grouted shafts display stiffer load-displacement response during subsequent downward, superstructure induced, loading compared to ungrouted shafts. Verification of resistance on each and every shaft through the use of post grouting will allow an increase in resistance factors (reduction in safety factor) used in the design. Two 6 ft. diameter drilled shafts were constructed in Fredonia, WA, for WSDOT, each with an approximate length of 52 ft. The shafts were terminated within medium dense poorly graded silty sand. Statnamic load testing of the shafts indicated maximum derived static side shear and base resistances of 2545 kips and 507 kips (1.6 in. displacement) for shaft One and 2466 kips and 212 kips (1.4 in. displacement) for shaft Two. Shaft Two was subsequently grouted, with a low mobility compaction grout. Shaft base mounted total earth pressure cells measured a maximum sustained pressure of 55.44 ksf during the compaction grouting operation. Shaft displacement reached 0.65 inches in the upward direction at termination of grouting. Comparison of grouting data with initial load test information indicates that properly instrumented post grouting verifies shaft base and side shear resistance. In addition, these grouting induced resistances were much higher than design values supplied by the engineer using conventional resistance factor design. Large scale laboratory testing also shows that base grouting verifies higher soil resistances than permissible in conventional design.

Jan 1, 2010

By Kazunori Matsushita, Masaru Sakakibara, Kenji Harada, Naotoshi Shinkawa, Mitsuo Nozu

The Sand Compaction Pile (SCP) method has been widely used as a typical countermeasure against liquefaction in Japan, and its effectiveness has been confirmed in many case histories of damages caused by the past large-scale earthquakes. A series of studies were conducted to evaluate the effectiveness of the compaction method and other factors, if any, in sustaining a seismic force that is greater than the assumed one and caused no damage. Based on the results of these studies, the Architectural Institute of Japan (AIJ) has indicated in its “Recommendations for Design of Ground Improvement for Building Foundations” published in 2006 that the liquefaction resistance ratio (tl/sz) of the composite ground, which consists of sand piles and surrounding compacted ground, is higher than the RL calculated by using the SPT N-values of the ground in-between the sand piles. In this paper, statistical analysis of safety factor against liquefaction, FL, was performed by using the SPT N-values of ground in Port Island and Rokko Island which were both fully reclaimed islands in Kobe city during the 1995 Hyogo-ken Nambu Earthquake (classified as intense shaking) and, together with the consideration of relative settlement, resulted in tl/sz of the composite ground being 1.5~2.5 times of tl/sz of the soil in-between piles after improvement. Furthermore, the liquefaction resistance curve of SCP-improved sites obtained from the relationship between SPT N-values and cyclic shear stress ratio during the 2011 off the Pacific Coast of Tohoku Earthquake, which was regarded as long-duration earthquake, was plotted to the left side of the curve originally proposed by Japan Road Association. Thus, the liquefaction resistance of the improved ground was found to be higher than that of the natural ground, even for the same SPT N-values, verifying the validity of the AIJ recommendation.

Jan 1, 2017

By Charles M. Wilk, Lori Tiefenthaler

"Information presented in this paper can be used to support deep soil mixing, subsurface grouting and slurry wall technology as sustainable construction technologies. Ordinary Portland Cement (OPC) is the default cementitious material used by Deep Foundation Institute (DFI) Members for geotechnical work. Owners, engineers and contractors can contribute to the sustainability of a geotechnical project by increasing the use blended hydraulic cements and industrial byproducts to replace some of the OPC in mix designs. Sustainability is defined as the quality of not being harmful to the environment or depleting natural resources. Production of cementitious materials consumes natural raw materials and energy while also generating air emissions and waste. Life Cycle Assessments can be used to compare the relative environmental impacts of one cementitious material to another. Blended hydraulic cements (BHCs) are interground (or blended) mixtures of Supplementary Cementitious Materials (SCMs) with OPC. Commonly used SCMs include fly ash, ground granulated blast furnace slag (GGBFS) and limestone. Examples of industrial byproducts commonly used in geotechnical work include coal combustion residuals (CCR) (aka fly ash), and ground granulated blast furnace slag (GGBFS). Much of life cycle impact of these SCMs and industrial byproducts have already been borne by the industries that generated them. There is increasing awareness to LCA and sustainability of different materials used on projects. This is evident in the application of the Leadership in Energy and Environmental Design (LEED) program. The savings in environmental impact with the use of SCMs and industrial byproducts can make proposed use of these materials in a geotechnical project more attractive in terms of sustainability. This paper presents (a) information that compares published life cycle assessment data of OPC, BHCs, and slag cement (SC) to illustrate the potential benefits to sustainability and (b) general strategies for positioning a geotechnical application, use, project design or cementitious material mix as a more sustainable alternative"

Jan 1, 2017

By Jason Buenker, Molly Winston

Torque-installed piles are gaining popularity in Southern California as the go-to deep foundation element for small- to medium-capacity loads in urban environments. The torque-installed pile is a displacement- based screwed pipe pile with a closed-end conical tip welded to the bottom of the pipe. Torque-installed piles are most efficient in loose to medium dense soils with high liquefaction potential. Where used properly, torque-installed piles can be installed faster, require less clean-up, and create less onsite vibration/disturbance than other pile alternatives. However, torque-installed piles are not applicable in all soil conditions and care must be used to apply the pile effectively in the correct subsurface environment. This paper will review current Southern California state-of-the-practice for torque-installed pile design and construction, potential roadblocks to successful installation, and available capacities from load tests. INTRODUCTION Torque-installed piles are a type of full-displacement screwed pipe pile originally developed in Southern California circa 2001 by Substructure Support, Inc. The pile is unique for its proprietary closed-end conical tip shown in Fig. 1. The tip has a welded steel-helix plate and cutter teeth that allow the pile to be advanced efficiently under applied torque and down pressure (crowd). Since original development of the pile, several contractors or manufacturers have proposed similar proprietary screw-type piles with comparable conical tips. Pile installation is relatively quiet, vibration-free, does not generate spoils, and faster than comparable pile types. The pile was originally developed as an alternative to driven pile foundations and remains a critical substitute to driven foundations in urban environments. Torque-installed piles are conventionally specified as 12 ¾-inch outside diameter (OD) steel pipes with a ⅜-inch-thick wall, although larger sizes with alternative dimensions have been used outside Southern California. Pile installation lengths generally range from 30 to 50 feet but may reach 80 feet or greater where soil conditions permit. The pile is generally backfilled with concrete following installation to increase lateral pile stiffness and may incorporate rebar cages or other reinforcing steel to facilitate connections to structural elements. The pile is frequently specified using performance-based specifications that encourage contractor innovation and use of proprietary installation means and methods.

Jan 1, 2019

By Robert F. Stevens, Robin Givet, Kenneth Viking

"Summary This paper describes a case of a directional pile installation conducted from an existing oil platform in the Caspian Sea, offshore Baku. Results are presented for 660 mm outer diameter (660 mm OD) conductor piles. Each conductor was equipped with a beveled aluminum toe for directional impact driving and was driven through a 710 mm casing using a Delmag 100–13 diesel hammer and a chaser pile. The 710 mm casings were preinstalled to a depth of 75 m below mud line (75 m BML). The longest impact driven conductor pile on the project was 456 m at end of drive, and reached the terminal depth of 295 m BML.Soil conditions consisted of soft to stiff silty clay to a depth of 30 m BML, underlain by stiff clay to 96 m BML, very stiff silty clay to 200 m BML, and very stiff to hard clay down to 300 m BML.In order to assess the maximum stresses in the conductors and check the performance of the hammer, the driving of each conductor was monitored using a Pile Driving Analyzer (PDA). The hammer fuel setting was adjusted based on the PDA outputs to ensure the conductors were not overstressed during installation. All driving and monitoring operations were carried out from the drill floor.The conductor piles drove easier than anticipated but in the direction predefined by the pre-cut angle of the beveled aluminum toe. The driving system performance was good. Post driving, the SRD were analyzed by either the global method analysis, using WEAP, or by the CAPWAP program.To detect any collision between the conductor being driven and the adjacent wells in production, the well heads were monitored in real time with high sensitivity accelerometers. These accelerometers were connected to an alarm system on the drill floor, triggering a siren and a strobe light should a collision be detected by an abnormal increase of the peak acceleration.IntroductionThe world longest directional impact driven pile was installed in year 2005. The operation was carried out from an offshore production, drilling, and quarters (PDQ) platform located about 120 km east of Baku, in the Caspian Sea.The platform foundation consists of driven piles and 24 slots were available for drilling the wells to the reservoir, located about 3800 m below sea floor. Each slot was fitted with a casing, 710 mm in diameter, running from the top of the jacket to a depth of about 75 m BML (Figure 1). Oil production started in 1997 and by the end of 2003, 14 wells were in operation; 10 slots were therefore still available, either for oil production or for water injection. However, due to larger than expected settlement of the platform, drilling of additional wells was put on hold. After further investigation, experts concluded the settlement was due to an alteration in the mechanical properties of the bearing strata supporting the foundation piles. This alteration was due to either excess soil material transportation, or soil fracture by the drilling fluids (mud), when drilling the first wells. With only 14 wells in production, out of 24 possible, the owner faced a new dilemma: to drill, or not to drill new wells?"

Jan 1, 2014

By Ambarish Ghosh, Rituparna Dey, Indrajit Chowdhury

"In port and harbor facilities, jetties and cargo berth terminals are usually installed on piles that remain partially embedded in soil, while a part of it behaves as columns supporting top deck. Technology in vogue adapts a pseudo static analysis in computer where the top deck including piles are analyzed as an integrated system based on finite element method when the piles are modeled as beam elements, while the soil in which it is embedded is modeled as linear or nonlinear springs. Typical berthing force of the ship is considered as a pseudo static force where the dynamic characteristics of the force is taken into consideration by an equivalent impact factor and little study exists on the actual behavior of these type of piles under the transient shock due to berthing impact. Present paper proposes an analytical solution based on which one can compute the dynamic response of such jetty piles considering shear modulus of soil constant with depth. Considering the solution is analytical in nature no special software is needed and can well be adapted fordesign office practice using generic utility software like MATHCAD, MATLAB etc. that makes theproposed model computationally very efficient.INTRODUCTIONResponse of piles under dynamic load has been an important study in the realms of civil engineering, where significant research has been carried out on its dynamic behavior under harmonic loads like one experienced in a machine foundation or under seismic force.A number of researchers have given solution to this problem like Parmelee et al (1964), Tajimi (1966), Penzien (1970), Novak et al (1974, 1983), Banerjee and Sen (1987), Dobry and Gazetas (1988),Chowdhury and Dasgupta (2008).However, most of these theories are based on piles loaded under harmonic load and valid for long piles where structural failure precedes the soil failure considering the piles are long and flexible."

Jan 1, 2015

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan

During the last phase of the Circunvalacion Norte project in San Jose, Costa Rica, preliminary designs for an underpass structure of over 16 km (10 miles) considered drilled shafts as an earth retaining system. Since the project’s execution was delayed and close to the deadline, it was necessary to optimize this structure, with the drilled shafts being the most critical aspect. The key element in order to obtain an improved design was characterizing the job site with a specific site study for seismic demand, and the use of advanced numerical modelling, considering soil-structure interaction. The site investigation comprised the CPT, PMT, MASW geophysical tests, deep exploration drilling, and triaxial compression tests. The terrain was modeled using an advanced constitutive model with hardening plasticity calibrated from the triaxial tests. Plaxis software was used to calibrate the seismic model for the terrain and for the dynamic analysis. Two conditions were considered for the retaining structure: free-head and fixed head. A parametric study with drilled shafts of 1.0 m (3.3 ft) and 1.2 m (3.9 ft) in diameter, and center-to-center spacing of 1.3 m (4.3 ft) and 3.0 m (9.8 ft) was conducted in order to obtain an optimized structure. For each condition of the drilled shaft wall, the computed deformations were compared for two spectrum designs: site-specific spectrum and seismic code generic spectrum. Finally, a dynamic analysis was performed to check the performance of the drilled shafts with optimized spacing using a control earthquake. Based upon seismic performance curves, the analysis showed the possibility of greater spacing for the drilled shafts compared to the original design, obtaining a 32% reduction in the total length of the drilled shafts in the project.

Oct 1, 2022

Technically speaking, the concept of NDT sounds like the "magic bullet" when faced with a questionable drilled shaft. All the Contractor or Engineer needs to do is select an NDT method, apply it, understand the details and extent of the defect and determine whether it will impact the load carrying capacity of the shaft during it’s design life. Unfortunately, it is not that simple. NDT is a tool utilized to indirectly assess the condition of the completed drilled shaft. For the most effective interpretation, NDT data should be correlated with the subsurface information, visual observation, and detailed shaft installation records. The basis for acceptance or rejection of drilled shafts should not be solely based on NDT. The parties responsible for specifying, interpreting and using the NDT results must understand the capabilities and limitations of the method to be utilized, in conjunction with the relevant subsurface conditions of the site, before selecting and specifying a system and acting on the results. This is necessary so that an appropriate NDT method can be specified and contracted. In this manner the results and roles of the responsible parties can be clearly defined.

Jan 1, 2004

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Numerical lateral load analysis based on the beam on Winkler foundation (BNWF) model (i.e., the p-y method) is a simple, and widely used tool to predict lateral responses of drilled shafts from field load tests. The lack of a site-specific p-y model for cemented soil layers such as caliche is one of the major limitations of simulating lateral load tests conducted in Las Vegas Valley. In this study, some of the existing p-y models for rock materials, such as Florida Limestone and Vuggy Limestone have been evaluated to simulate the lateral resistance of caliche. This has been done in the context of four lateral load tests in caliche-dominant sites from the recently constructed Raiders Stadium project in Las Vegas (NV). The uncertainty in characterizing the material properties of caliche has been addressed. The p-y analyses were performed using NVShaft, a MATLAB-based, comprehensive load analysis program. The applicability of the considered p-y models for caliche material was evaluated by quantifying the normalized error margins between measured and predicted lateral responses from the simulations of the mentioned load tests. Correlations between such errors and the depth and thickness of caliche in soil layers affecting numerical predictions were established, for both up to and beyond design load levels.

Oct 1, 2022

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees is applied to a 0.61 m flagpole and a 0.61m fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil is represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2011

By Marco Fellin, Van E. Komurka

Significant cost and construction benefits were obtained from performing a bi-directional static load test prior to construction on the Russell Street Bridge Replacement project in Missoula, Montana. The project utilized 24 drilled shafts to support two three-span bridges across the Clark Fork River. A bi-directional static load test (“BDSLT”) was performed on a large-diameter production shaft to demonstrate construction methods and confirm design assumptions. Subsurface conditions consisted of gravel with sand to a depth of 20 feet (6.1 m), underlain by gravel with sand, silt, cobbles, and occasional boulders. The test shaft had a nominal diameter of 5.9 feet (1.8 m), and an embedded length of 75.5 feet (23.0 m). The geotechnical engineer of record and the BDSLT test engineer collaborated to optimize the BDSLT jack assembly location within the test shaft, determine appropriate instrumentation locations, and plan the test protocol. The maximum applied test load was 10,707 kips (47.6 kN). Significant benefits were obtained from performing the BDSLT test, including 1) reducing each production shaft’s length by using a higher LRFD resistance factor allowed by having performed the testing, 2) using test-determined unit shaft resistances to evaluate and accept two production shafts that may have otherwise required remediation, and 3) providing the Montana Department of Transportation (and other designers) with increased presumptive unit resistance values in the gravel/cobble/boulder deposits. PROJECT DESCRIPTION The project was constructed in Missoula, Montana for the Montana Department of Transportation (“MDT”). The original bridge was approximately 60 years old, and consisted of a two-lane, 420-foot-long (128-m), four-span, riveted steel plate girder design spanning the Clark Fork River. The bridge was due for replacement owing to its deteriorated state, and the need for increased traffic volume capability afforded by a four-lane structure. HDR was the structural engineer. The preferred bridge alternate was a 459-foot- long (140-m), three-span, welded steel plate girder design. The new bridge was designed to meet current standards in accordance with MDT bridge design and AASHTO LRFD criteria. The new bridge was constructed in phases to keep traffic open during construction.

Jan 1, 2019

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid shoring system consisting of cast-in-place soldier piles with Cutter Soil Mixing (CSM) infill panels was constructed for temporary support of a 19.8 m (65 ft) deep excavation in Vancouver, British Columbia, Canada. Deep Mixing (DM) was completed up to 9.7 m (32 ft) in fill, peat, wood waste and clayey silt with embedment in dense till, and soldier piles constructed through the dense till extending to below final excavation level. Two trial CSM panels were installed ahead of production to assist with developing the termination criteria of the CSM panels in the dense till. The constructed depth of the CSM panels was based on interpretation of real-time monitoring data obtained through the Bauer B-tronic system. Inclinometer monitoring data from two CSM panels and two soldier piles, as well as soldier pile survey target data was used to assess and monitor the performance of the hybrid shoring system throughout bulk excavation. The objectives of this paper are to provide an overview of the design and construction aspects of the hybrid DM shoring system and to present inclinometer and pile target data to demonstrate the lateral performance of the CSM infill panels and soldier piles. This paper also discusses the merits of using real-time monitoring data as part of the engineering decision-making process for validating CSM panel construction. BACKGROUND A hybrid DM shoring design was recently completed for a high-rise development in downtown Vancouver, British Columbia for temporary support of a five level basement excavation. Deep mixing was proposed by the excavation and shoring design-build team as the preferred method to construct infill panels between soldier piles because of the speed at which the shoring system could be constructed in variable fill, peat, wood waste and overburden compared with traditional secant piling methods. The development site is generally a truncated triangle in plan, with the longest side of the triangle being approximately 115.7 m (380 ft) long and the two shorter sides being approximately 71.6 m (235 ft) (Hybrid Shoring Wall 1) to 75.0 m (246 ft) (Hybrid Shoring Wall 2) long. The site is bounded by an existing bridge off-ramp structure along its longest side, and by city streets on the other two sides, as shown in Figure 1. The truncated section is approximately 16.8 m (55 ft) (Hybrid Shoring Wall 3) long. Due to project constraints, the hybrid DM and soldier pile shoring system was only proposed for the two shorter sides of the triangle and the truncated section. Traditional secant piles were installed for the longest side. This paper focusses on the hybrid shoring system. A typical detail showing the CSM infill panel with the soldier piles is presented in Figure 2."

Jan 1, 2017

By Mahesh Hingorani

Integrity issues for bored cast-in-situ piles have raised the need for the use of non-destructive tests to verify pile integrity and detect possible anomalies in installed pile sections that could adversely affect their serviceability. Integrity inspections performed after installations are often the most reasonable alternative available to assess the shaft quality. The two most common methods are pulse-echo from a small hand held hammer at the pile top, and cross-hole ultrasonic transmissions along the shaft between parallel sonic pipes. While different in technique, each method has its advantages and limitations. This paper emphasizes more on the degree of accuracy of low-strain pile integrity test by comparing the results with cross-hole sonic logging. Reliable data collection and interpretation by an experienced test engineer will reveal the integrity of the pile. Cross-hole sonic logging and low-strain pile integrity testing were both specified as quality control measures for a metro rail project in India. Both cross-hole sonic logging and low-strain pile integrity testing indicated defects in several bored piles. Also minor imperfections recorded by cross-hole sonic logging were observed in low-strain results. The observations of the two test methods are presented and compared for a better understanding of the importance of low-strain test results for any project. INTRODUCTION Cast-in-situ concrete piles are often chosen as a deep foundation alternative where challenging soil conditions exist. Although quality control measures are almost always taken during the installation of the piles, it is often difficult or impossible to confirm the integrity of the pile at this stage, particularly in wet conditions. Because of the relatively high probability of bored piles having anomalies, quality assurance of each bored pile is essential for each project.

Jan 1, 2019

By Dimitrios Polantzas P. E., Collin E. Sweeney E. I. T., Franklin M. Grynkiewicz P. E., Leili Javidanian P. E.

In the latest AASHTO design specifications, the Load and Resistance Factor Design (LRFD) method is prescribed for the design of retaining walls. However, inconsistencies arise when LRFD is used for retaining wall design versus the traditional Allowable Stress Design (ASD). Required toe embedment and wall loading demand vary greatly when the two design approaches are compared, all else being equal. This is due to application of linear load factors to properties that vary non-linearly in the design. These inherent inconsistencies are further intensified when introducing factors such as layered soil profiles, different wall types, groundwater elevation, and surcharge requirements. When applied correctly, these two design approaches, in theory, should lead the designer to the same result with little discrepancy, as they do with steel structure design. However, the use of the current AASHTO LRFD method for various geostructural retaining wall designs yields contradictory results that suggest existing retaining walls that have been successfully designed and constructed are unstable. Fundamentally, LRFD should be built on reliability-based calibrations; the successful past performance of existing retaining structures designed using ASD suggests that the LRFD approach requires considerable modification. The authors of this paper recommend that the current LRFD load factors be reviewed and revised based on more comprehensive wall performance data and wall type such that the difference between retaining structures designed using LRFD and those designed using ASD is eliminated.

Oct 1, 2022