Search Documents

By A. Gronningsater

Introduction As is well known, the fight between the blast furnace and the reverberatory furnace in copper smelting during the second decade of the century ended with a victory for the latter, a result which must largely be attributed to the introduction of flotation methods. To my knowledge, no new blast furnace has been blown-in at any American copper smelter since the War. As the metallurgy of nickel, up to and including matte smelting, is generally considered a close parallel to that of copper, the introduction of reverberatory smelting in the big new smelter of the International Nickel Company at Copper Cliff, built in 1928-30, seemed a logical adherence to a well established trend. In view of these facts, considerable comment was made when Falconbridge Nickel Mines decided to retain the blast furnace in their smelter built about the same time, in 1929. A presentation of the reasons governing this choice should therefore be of interest. The basic principles underlying the Falconbridge practice, and the considerations guiding the successive steps in the operations, will be discussed in the following. To understand the problems involved, the character and mode of occurrence of Sudbury ore must be kept in mind. Large amounts of disseminated ore are generally present. Although the gangue usually runs only about 50 per cent Si02, the ore hoisted as a rule contains more silica than needed in the smelting operation; until recently this excess was removed entirely by hand picking (in later years supplemented by magnetic sorting methods), a difficult and not very satisfactory method, in which 'the border line between ore and waste is entirely arbitrary, and therefore too much depends on the judgment of the picker.

Jan 1, 1934

By J. A. Russell

AS THE LOCAL electric generating plants increased in size and capacity and costs of producing electricity came down, it became apparent that it was no longer good economy to operate individual boiler plants at the Company's various collieries to power steam hoists and compressors. Great economies could be made by burning the Coal at central power plants and using electric power at the collieries. During the period after the end of the war, a steady and continuing programme of replacing first the smaller steam-driven units, and later the steam-driven compressors, was undertaken, and finally the larger hoists, those at No. 12 Colliery in New Waterford and No. 20 Colliery in Glace Bay, were the last units operated by steam.

Jan 1, 1958

By Justin S. Johnsen

As OEM sensors and interfaces have grown in number, the available data from equipment in the mining environment has continued to multiply. This equates to an increased visibility of operating performance, mechanical and electrical health, and predictive monitoring that can directly improve maintenance reliability and scheduling. With increased visibility, where should a reliability engineer begin to look to directly impact Capacity Assurance? More specifically, what source will provide inputs to the Failure Modes Effects Analysis (FMEA)? Results from these analyses must be documented, and they must contribute to the overall mission of the mining company; these results must reduce costs and increase profits. Through detailed data capturing, documenting, and analysis, Modular Mining Systems? Time Tracking application, used in the MineCare® maintenance management solution, can drive decisions and provide direct impact to engineering projects for continuous improvement in the mine maintenance organization.

Nov 1, 2011

By Ian Hattie, Mark R. Wilson, T. Kurtis Kyser, Brian W. Janser

Petrographic, chemical and isotopic compo itions of auriferous and non-auriferous quartz vei ns from the Sta r Lake and Flin Flin-Amisk Lake areas of northern Saskatchewan indicate diver e origins fo r the fluids associated with gold mineralization. In the Sta r Lake area, the metavolcanic , Star Lake pl uton, and heared mafic dikes have retained their original igneous 81 80 values. The 81 80 value of quartz from mi neralized veins vary by I per mi! and range from+I0 to+IJ. The only quartz ample having a 81 80 value outside th is range came from a vein not associated wi th a dike or gold mineralization . Quartz from the Star Lake pluton has identical 8180 value to the qua rtz from mi neralized vei ns which suggests that the vei ns and the pluton are related to imilar proces es. The diffe rence in 81 80 values between mi neralized and barren vein may erve a a potential exploration tool in this area. Because o34S val ues of a limi ted number of amples of pyrite from gold-bearing quartz vei ns at Star Lake correlate directly with gold content. the gold may have been syngenetic with the su lphur and the 834 value may be useful for exploration . 8180 values of co-existing quartz, calcite, and amphibole in the veins from Star Lake indicate that isotopic disequilibrium among the minerals is common, but the val ues also record a high temperature of formation (ea . 500°C) involvi ng a component of magmatic fl uid. TheoD value of hydrou mineral from Star Lake retain their original igneous values but whole rock values are generally much lower, an effect attributed to interaction of the minerals with a late meteoric water. In the Fl in Flin-Amisk Lake area, auriferou and barren quartz veins formed from a mixture of hydrothermal and metamorph ic flu id at lower temperatures (ea . 350°C) than those at Sta r Lake. Becau e there i no apparent correlation between 8180 values of the quartz with gold content or relative age of the vein , nor between the 834S val ues of pyrite and gold content, table isotopes appear limited as an exploration tool in the Fl in FlonAmisk Lake areas.

Jan 1, 1986

By Jack J. Ayotte, Michael R. Nadon

"Today's demand for better and more efficient methods inspires new approaches to construction and mine development.A project at Asarco's Aquarius Mine provided a challenge that resulted in the adaptation of a civil construction technique to a mining application.This paper describes the construction of an escapeway shaft to surface from the mine's 150m level. The prime consideration was to provide the most cost-effective method of establishing a shaft collar in the 145 ft (44 m) of water-bearing overburden. This problem was resolved with the employment of the drilled in-caisson method.The remainder of the 500ft (152m) deep shaft was raise bored and portable hoisting equipment was used to install a permanentmanway and shaft liner.IntroductionHaving completed the first phase of exploration development in 1982, J.S. Redpath Limited was engaged to carry out an engineering and cost study to investigate the feasibility of re-opening Asarco's Aquarius Mine near Timmins, Ontario. The scheme was to develop the proven ore reserves and proceed with shrinkage stoping while carrying out further exploration development and diamond drilling.One significant and costly component of the project was the provision of an escapeway shaft to supply additional ventilation as well as a second means of egress from the mine. The major complication to this task was the presence of 145 ft (44 m) of water-bearing overburden at the site. The first and obvious approach was to use conventional ground-freezing methods as had been employed previously on .this property for the initial development shaft. This being the only ""sure"" method available at the time of the budget estimate, it was used as a basis for the study but its considerable projected cost and time demand inspired further investigation into other possible solutions.After considerable research and several brainstorming sessions, a Redpath team came up with an approach whose basic procedures had been used extensively in the civil construction field, although they were novel to the mining industry."

Jan 1, 1987

By Ben Bradshaw

Context ? Community engagement has become an increasingly significant and challenging part of mineral exploration and mine development; indeed, opposition from communities proximate to a proposed mine site has been known to derail technologically- and financially-sound projects. ? These cases suggest that mining firms need to better understand how to engage constructively with local communities in the pursuit of their claims. ? While a range of publications exist promoting various community engagement strategies, these recommendations, when viewed as a whole, are disjointed and largely untested in real development contexts. Aims of Presentation 1. Synthesize industry, NGO, government and academic publications focused on community engagement best practice in order to highlight those practices that are most commonly recommended. 2. Review the (Canadian) mining industry?s experience with some of these strategies based on existing case material in order to identify the extent to which commonly prescribed strategies are used and validated in practice.

May 1, 2010

By W. L. Ott, J. E. Hawley, C. L. Lewis

"IntroductionTHE APPLICATION of spectrochemical analysis to metals of the platinum group was advocated by Harvey (3) as follows: ""The spectra of the platinum group metals have been studied less than many of the more common metals. The rarity of occurrence of these elements makes the analysis relatively unusual. Potentially, the analysis of this group is an excellent application of spectrographic methods, particularly in contrast to the tedious chemical procedure"".Wichers (8) divides platinum-metal analysis into three broad divisions as follows :( 1) The detection and estimation of these metals in other materials, e.g., ores, where the amounts present are very small.(2) The detection and estimation of impurities in the refined metals themselves ....(3) The analysis of alloys of the platinum metals .....The present paper deals with the second division: analysis of refined rhodium.Research on spectrochemical techniques for determination of trace contaminants in refined platinum metals was begun at Queen's University in 1949, under the supervision of Professor J. E. Hawley. Since 1953, the work has been continued in the Metallurgical Laboratories of Falconbridge Nickel Mines, Limited. Techniques for spectrochemical analysis of refined platinum and palladium have been published ( 4, 5). A technique for analysis of refined iridium has been developed but not yet published."

Jan 1, 1955

By Peter C. Jones

The paper gives a broad view of the maintenance procedures at the Cassiar Asbestos Corporation property. Comparisons are drawn to indicate the changes in facilities and approach that have evolved over the last 25 years while coping with the northern British Columbia climatic conditions. Special emphasis has been placed on the importance of the support groups providing services for both the mine site and the town.

Jan 1, 1978

By J. Bélanger, B. Semlali, M. Grenon

RÉSUMÉ La conception des fosses ainsi que l'évaluation des ressources géologiques et des réserves minières sont désormais réalisées entièrement à l'aide d'outils informatiques spécialisés. Cependant, plusieurs analyses, pourtant essentielles à l'évaluation de la viabilité du projet, sont réalisées en parallèle sans véritable optimisation ni synergie avec l'ensemble des données disponibles. Cet article présente deux approches permettant d'intégrer certains types d'analyses aux modèles de blocs miniers. Ces approches permettent de quantifier la broyabilité du massif rocheux ainsi que d'étudier la stabilité des pentes minières à même les outils d'optimisation et de planification minières. Cette méthode permet dès l'étude de faisabilité d'un projet minier de maximiser les données disponibles, menant ainsi à une approche plus intégrée en conception minière. De plus, ces approches sont flexibles et permettent d'évaluer rapidement plusieurs scénarios, tout en laissant la possibilité de bonifier le modèle et de revoir la conception tout au long du projet minier.

Jan 1, 2010

By J. P. Dick

THIS paper is a description of the milling practice and metallurgy at the Moneta Porcupine mine, Timmins, Ontario. The results obtained with an all-cyanide circuit and later with flotation followed by cyanidation are described. The ?investigation which prompted the various changes in milling practice have also been dealt with. Moneta ore is possibly the most refractory now being milled in the Porcupine district. This is due to the ultra fine state in which the gold occurs and to its intimate association with pyrite. No doubt there is ore of similar characteristics on the neighbouring properties but it probably forms only a small portion of the tonnage being mined, whereas at Moneta the bulk of the ore requires an extremely fine grind to liberate the gold. The fineness to which an ore can be ground economically has gone far beyond what was thought to be the limit only a few years ago. Formerly, a set of standard screens was all that was required to measure the fineness to which an ore was ground. At present, the Haultain infrasizer is practically indispensable, and the nominal micron has become a familiar unit of measurement to all those dealing with the problems of fine grinding.

Jan 1, 1941

By H S. Ellis

Flow studies have been conducted on nickel-water suspensions in a 1in.-diam., 42-ft.-long transparent lab-oratory pipeline at concentrations of up to 25 per cent, by volume, and slurry velocities of up to 15 ft/sec. The average size of the nickel powder was approximately 150 mesh (106J.L). Three flow regime were noted. At the highest velocities, i.e., above 10 ft/;sec., where the concentration distribution through the vertical diameter was most uniform, pressure gradients could be correlated with the Durand-Condolios equation (7,8). An intermediate region, i.e., from 7 ft/sec. to10 ft/sec., could be distinguished, the lower velocity limit being that at which nickel particles began to deposit. This region was also marked by decreasing pressure gradients, for a given concentration, as the velocity was reduced. The upper velocity limit in this region was also uniquely defined in that the friction factor for any nickel concentration was the same as that for water. In the third regime, below about 7 ft/sec

Jan 1, 1963

By Stephan I. Zajac, Roger A. Blais, John B. Stubbins

THE iron deposits of central Labrador occur within a relatively small area, herein called the Knob Lake Iron Range, in which a northwest-trending series of low hills and ridges defines the height-of-land at the boundary between provinces of Quebec and Newfound-land. Approximately two-thirds of the deposits are in Quebec and the remainder in Labrador, with several deposits straddling the inter-provincial boundary. These deposits are being exploited in open-pit mines by the Iron Ore Company of Canada centered at Schefferville, Quebec. Since 1954 this company has produced more than 56 million tons of iron ore to become Canada's leading iron ore producer. With indicated reserves of more than 375 million tons of direct-shipping ore and large tonnages of iron formation amenable to beneficiation, this mining district is assured of a long life. This paper describes the Knob Lake iron ores and their geological settings and stresses the features that lead to a better understanding of their origin. The

Jan 1, 1961

By C. W. Taylor, F. L. Martin

"THE DICTIONARY defines Metallurgy as the ""science or art of separating metals from their ores and refining them for use"". In these days, however, such a definition is not detailed enough.The modern science of metallurgy is based on two fundamental sciences, physics .and chemistry, and is sub-divided into two major fields: Process Metallurgy and Physical Metallurgy. These fields of metallurgy are now so comprehensive and involved that even the graduate metallurgist has to specialize in one or the other.In recent years, the relatively new science or technology of non• destructive testing has also entered the industrial scene, with tremendous impact and ramifications. So much so that, certainly, no .discussion on metallurgy can be complete without including some reference to it.Obviously, one paper cannot hope to cover in detail the relationship of the whole science of metallurgy to the mining industry. Consequently, only a very brief reference will be made to the field of Process Metallurgy, our major concern being with Physical Metallurgy and Non-Destructive Testing."

Jan 1, 1960

By G. E. Viens, R. A. Campbell, G. N. Banks

A survey of the literature reveals wide differences in the procedures used in making iron ore pellets and in the properties of the pellets obtained. In this paper, the methods of production and the properties of pellets, as reported in the literature, are examined in an effort to determine what correlations exist between them. An attempt is also made to determine the levels of the properties of pellets which are considered acceptable and desirable in modern practice. M UCH has been written regarding the important changes which have been taking place recently in the iron ore industry. As the demand for ore has increased and the supply of direct-shipping ore has dwindled, tl1e problems associated with the utilization of lower grade ores ha\•e been intensely investigated and important advances in both beneficiation and agglomeration techniques have taken place. In particular, there has been a great deal of activity in connection with the pelletizing method of agglomeration. The superiority of pellets over raw ore has been demonstrated in blast furnace tests

Jan 1, 1962

By G. F. Cross

INTRODUCTION THE electrical system associated with the mining development of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, may be conveniently divided into three main parts, namely, the Island Falls power plant, the transmission line, and the distribution systems at the mine and metallurgical plants. For a description of the Island Falls power plant and the transmission line, the reader is referred to the paper, to be presented at this meeting, by R. W. Davis and M.F. Huffaker (1). The transmission line and sectionalizing combinations are shown diagrammatically in Figure 1. The present paper deals with the distribution systems at the Flin Flon mine and metallurgical plants. THE FLIN FLON DISTRIBUTION SYSTEM In the high-tension sub-station at Flin Flon, each incoming 110 kv. line is provided with manually operated, gang-type disconnecting switches. Each line is connected to Canadian General Electric type F.H.K. 39-60B-F.2 T.P.S.T. 110 kv. 400 amp. oil circuit breakers, each provided with M.K.4 centrifugal motor-operated closing mechanism. Gang-type disconnecting switches are installed on each side of incoming line breakers, and a complete ring bus system is formed through station tie breaker, which is' further provided with gang-type disconnecting switches on either side. The?bus tie breaker is of Canadian Westinghouse design, type G.22B, 110 kv., 400-amp., solenoid-operated. All three breakers are provided with bushing-type current transformers, and the two line breakers are further equipped with bushing-type potential devices. Oxide film lightning arresters (121 kv.) are installed on each incoming line and are located outside the station. Each line is further provided with interlocked gang-operated ground disconnecting switches. All disconnecting switches are mechanically connected to auxiliary switches, which provide pilot service to indicating lamps in the remote-control room, located in a separate building.

Jan 1, 1935

By J. B. Gilliatt

The discovery of ore at Wabana was quickly followed by the mining of the ore beds where they outcropped in the land areas. The third phase, as at present carried out, consists of extensive submarine operations, which were commenced in 1908, by driving a pair of slopes out under Conception bay, opening. the mine for a distance of a mile and a half from the shore. Two other slopes, now driven just beyond the shore line, are being sunk to the submarine territory where, it is generally recognized, huge reserves of ore lie under the bay. The process of erosion of the land, the solution and re-disposition of its iron-bearing minerals in thick beds of ore have been considered elsewhere, but these bear small relation to the physical forces which have acted upon the ore-beds since the deposition of the strata. These physical changes are made manifest by jointing and cleavage and faulting. The discussion of these, the relation they bear to each other, and to the folding of the strata, is the purpose of this article. For the benefit of those who may not be familiar with the formation in which the ore occurs, I include a general summary of the geology of Be!! island and its environs; also a description of conditions that prevailed during the period of deposition, so that the reader may appreciate some of the later changes that took place during or subsequent to its emergence from the sea, and the folding or tilting of the strata to the position it now occupies.

Jan 1, 1924

By Ralph D. Parker

THE subject matter of this paper will be primarily restricted to the metallic mineral industry, which last year was responsible for almost 60 per •Cent of the total value of Canada's mineral production. It has been written that, in the broad sweep of eternal time, sixty years is as transient as a flicker of lightning in a summer night's sky. In the history of mankind and human endeavour, however, six decades can encompass momentous events and far-reaching •circumstances, all of which affect the lives of men and change the destiny of nations. This observation is con-firmed very positively by a study of our Canadian mining history, from either the broad viewpoint of human progress or the more specialized viewpoint of national economy. The past sixty years have witnessed vast changes in the economic importance of mining in this country's affairs, and also in the technology of the industry. Mining has emerged from the days of rule-of-thumb practice and is now taking on the stature of a highly diversified science.

Jan 1, 1962

By T. W. Wloder

During recent studies concerning the effects that various surface treatments, surface imperfections, locked-in residual stresses and metallurgical and geometrical notches have upon the mechanical behaviour of metals and, in particular, upon their tension-bending characteristics under impact loads, it became apparent that specially developed methods and samples would be of great assistance in determining the desired data. This paper describes and discusses a number of different types of double-notched tension-bending impact samples which have been considered and examined for this purpose. The types most suitable for exploratory investigations are proposed for application in the study of the _behaviour of metals, their welds, and, in particular, their surfaces, when subjected to various notch-severities, surface imperfections, strain rates, temperatures, and constrained states of stress (i.e. the relations of the three principal stresses). It is expected that the proposed double-notched tension-bending samples and the proposed test methods will also contribute toward further understanding of the cold brittle behaviour and the notch-sensitivities of metals. The possibilities of introducing the so-called impact notch-sensitivity index and relative impact notch sensitivity of metals are discussed. Data obtained on double-

Jan 1, 1961

By J. W. Spyker, D. H. Filson, W. H. W. Husband

"Large deposits of sodium sulphate exist in southern Saskatchewan in the brines or muddy crystal beds of alkali Jakes. Currently, more than 300,000 tons per year of sodium sulphate are produced from these lakes and sold as salt cake to the paper industry. Most of the production is obtained from the brines of a limited number of Jakes.The Saskatchewan Research Council was requested to develop a process for recovering sodium sulphate from the muddy crystal beds so that this type of deposit could be exploited in the future. A flowsheet was developed with the aid of phase diagram data and the process was studied on a pilot-plant scale using raw material from three different lakes. Satisfactory yields and product purities were obtained in all cases, and an economic analysis indicated that a 100,000-ton-per-year sodium sulphate plant could produce salt cake at a cost of $12.26 per ton for a rate of return upon investment of 16 per cent at current market prices."

Jan 1, 1966

By M. King Hubbert

"The present large-scale use of energy and power by the human species represents a unique event in the billions of years of geologic history. Furthermore, in magnitude, most of the development has occurred during the present century. In the United States, the peak in the rate of petroleum production occurred in 1970 and that for natural gas is imminent. The peak in the world production of crude oil is expected to occur at about the year 2000 and that for coal production at about 2150 or 2200. For other sources of energy and power, water power, geothermal power and tidal power are inadequate to replace power from fossil fuels. Nuclear power, based on the breeder reactor and utilizing lowgrade deposits of uranium and thorium, has a larger potential than the fossil fuels, but it also constitutes a large perpetual hazard. The largest source of energy available to the earth is solar radiation. This source has a life-expectancy of a geologic time scale, is nonpolluting and is larger in magnitude than any likely requirements by the human s pecies. In consequence of the large supplies of available energy, the period since 1800 has been one of an unprecedented exponential industrial growth. This also has been accompanied by a world-wide ecological disturbance, including that of the human population. It can easily be seen that such a period of growth must be ephemeral in character and, in fact, is now almost over. One aspect of this transition from a state of exponential growth to a state of nongrowth is the present alarm over an ""energy crisis."" Actually, the world's present problems are by no means unmanageable in terms of present biological and technological knowledge. The real crisis confronting us is, therefore, not an energy crisis but a cultural crisis. During the last two centuries, we have evalved what amounts to an exponential- growth culture, with institutions based on the premise of an indefinite continuation of exponential growth. One of the principal consequences of the cessation of exponential growth will be an inevitable revision of some of the tenets of that culture."

Jan 1, 1973