Search Documents

By J. H. Archibald

"This paper describes the use of vector analysis for determining the intersection of mineral deposit veins. The mathematical evolution of the analysis is outlined.IntroductionMany mineral deposits can be characterized by sets of intersecting veins. Often a vein will have a steep dip and may intersect with another similar vein. Finding the intersections of these veins is usually done by graphical means. Structural geologists, by the methods of descriptive geometry, can usual ly predict where intersections of veins will occur. This method normally requires accurate drafting and layout of the problem and does not always lend itself to solution in the field.Another method for solving this problem involves the use of vector analysis, which is easily adapted to hand-held programmable calculators. It is assumed at the outset that the reader is familiar with the dot and cross products used in vector analysis. Two excellent references are cited at the end of this note for convenience.A plane, in general, is defined by three points. The points of interest here are the points where three vertical drillholes penetrate the vein, or plane, in question. The elevations of these three points are best referred to sea level. This requires knowing the elevation of the collar of the drillhole above sea level and the drillhole depth from the collar to the vein. The elevation of the intersection point is then found by subtracting the hole depth from the collar elevation. These three points now define the plane of the vein. A similar set of three points will define a second vein, and it is our object to show analytically their intersection if it exists."

Jan 1, 1983

By M. S. Moats, F. Elnathan

"The effect of current reversal on two commercially manufactured electrodes (RuO2-TiO2 and IrO2-Ta2O5 coated Ti) in a chloride bearing electrolyte was evaluated. Accelerated lifetimes were found to decrease with increasing current density and increasing reversal frequency. Ru: Ti coated electrodes exhibited longer lifetimes than Ir: Ta coated electrodes even though they had one-third as much precious metal content. Chloride concentration did not affect lifetime in the range examined. Using energy dispersive X-ray spectroscopy (EDS), scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS), the failure mode of the electrodes was determined to be coating dissolution leading ultimately to passivation by the presumed growth of a highly resistive oxide at the coating/substrate interface.INTRODUCTIONCatalytic titanium anodes (CTAs) were developed in the 1960’s to replace graphite anodes in chlor-alkali cells. CTAs exhibited much better dimensional stability than graphite leading to lower operating potentials by promoting smaller electrode gaps and better operational efficiencies as they had to be replaced less often. CTAs are simply Ti substrates coated with precious metal oxides (such as IrO2 and RuO2) mixed with other components (such as TiO2 and TasO5) (Trasatti, 2000).CTAs are used in many other electrochemical industries, including water disinfection, wastewater treatment, cathodic protection and metal plating. RuO2 based coatings are typically used for chlorine evolution. IrO2 based coatings are for the most part utilized for oxygen evolution (Comninellis & Nerini, 1991; Forti, Olive, & De Andrade, 2001; Kotz, Stucki & Carcer, 1991; Trasatti & Lodi, 1981)"

Jan 1, 2016

By Don Lemmen

Impacts, Adaptation and Vulnerability ? regional climate changes (temperature and extreme events) have already affected many physical and biological systems ? natural systems are vulnerable to climate change, some will be irreversibly damaged ? many human systems are sensitive to climate change ? Projected changes in climate extremes could have major consequences

Nov 1, 2002

By Robert B. Parsons

"New Brunswick Finance Minister John Baxter pulled something out of a hat for the mining industry in April, but there is a general concensus in the industry that he should put II back where it came from.The industry has never been in the mood f or progressive rate structures, but that is exactly what New Brunswick 's 1984 budget offers to this depressed sector of the economy.IntroductionThe Province of New Brunswick stunned the Canadian mining community in April with the announcement that the province' s 16% mining tax rate would be replaced with a progressive rate structure effective January 1, 1984 (Table I). The proposed change, contained in the bud get papers tabled by Finance Minister John Baxter on April 17, caught the industry totally by surprise. The move to a progressive rate structure was completely unexpected for a variety of reasons:• Generally speaking, relations between the province and the industry have been relatively good, yet the industry was apparently not consulted with respect to the proposed measure and had no indication that a change of th is nature was coming. This is in stark contrast to the mood which prevailed during the major revamping of the province' s mining tax regime in 1977: at that time, the industry was invited to contribute in advance to the province's plan for a new tax structure.• The new structure would appear to make th e province less competitive in terms of mining tax rates with Ontario , Quebec, and other provinces, despite indications in the past that New Brunswick is very cognizant of this competitive factor in formulating mineral policy.• A joint report in November 1978 by federal and provincial officials to federal and provincial finance and resource ministers, which was careful not to directly criticize Ontario and Quebec's progressive mining tax rate structures, recommended that provincial "" tax regimes be examined to ensure the inclusion of appropriate mechanisms to avoid the excessive taxation of cyclical type profit "" , and that ""the federal and provincial governments consider the concern over progressive tax regimes expressed by the industry and examine mining and royalty tax regimes and the income tax regime with a view to alleviating the effect of such regime on the aggregate marginal tax rate"". In this context, any move to a progressive rate structure would be viewed by many observers as retrograde."

Jan 1, 1984

By John E. Udd

"Mining research at CANMET is delivered by the Mining Research Laboratories Division (MRL), with facilities in Sydney, Nova Scotia; Bells Comers, Elliot Lake, and Sudbury, Ontario; and Val d'Or, Quebec. This paper gives an overview of the work of the Division as of early 1993. An addendum, at the end of this paper, describes the organizational changes that will take place in April 1994. IntroductionCANMET, the acronym for the Canada Centre for Mineral and Energy Technology, is the name by which the organization founded in 1907 as the federal Mines Branch is presently known. The name was changed in 1974, in order to give recognition to the importance of both minerals and energy technologies in the activities of the Branch. Further reorganizations have taken place since 1987. As a result of these, CANMET has assumed the status of a Sector (equivalent to the Geological Survey of Canada) and has been organized into four branches.The organization as a whole functions in an environment of semi-matrix management. Some of the ""line"" Divisions report to Directors-General for the appropriate branches while other, larger divisions, report directly to the Assistant Deputy Minister.The second dimension of the organizational matrix is composed of a number of ""staff' divisions which report to the DirectorGeneral for Policy and Planning. Each of these Divisions performs a function which is common to all of the ""line"" divisions. For example, the Research Projects Office is responsible for monitoring the range of research activities of CANMET and for recommending allocations of funds for both research contracts and operating budgets. The Library and Documentation Services Division is responsible for CANMET publications and information services. Likewise, the Engineering and Technical Services Division provides support through, among other services, the construction of specialized laboratory equipment."

Jan 1, 1994

By A. Mellek, M. Pischtschan, M. Perrucci

ABB has received an order for one of the most challenging mill drive projects in its history. With one SAG mill and one ball mill to be added at an iron ore mine in Sweden, the customer’s plant managers wanted to have the most efficient solution for driving their mills but had the budget limitations typically faced by the majority of mining companies during periods of market downturn. To find the best balance between cost of acquisition and highest performance throughout the lifetime of the plant, ABB was selected to deploy a synchronized bypass solution, in which only one drive system is used for two different mills in series. However, being one of the first grinding mills in the world with such a solution was not the only challenge the ABB team faced: The inclusion of some mill application functions - e.g., frozen charge protection, automatic positioning and creeping mode - brought the demands on the engineers to another level. With only one frequency converter and one mill application controller available, the configuration logic and interlocks had to be meticulously designed and thoroughly tested to ensure a smooth and safe startup. The solution offers a footprint reduction and more operator flexibility at a reduced investment as each mill can be run in both directions, and wear on the mechanical components can be greatly reduced due to ABB’s premium ring-geared mill drive (RMD). This paper will describe the details of the project, the configuration developed and the tests performed to guarantee correct software functionality. Mill startup is scheduled for January 2016.

Jan 1, 2016

By Chris Blain

"Abstract - Based upon an extensive database, this paper analyzes the record of modern mineral exploration success and establishes the 50-year trends in discovery. The record clearly shows that the overall discovery rate rose during the 1950s and 1960s, peaked in the 1980s, and fell during the 1980s and 1990s. By commodity and ore-type target, the pattern of discovery is not continuous. Typically, it is episodic as a series of waves with minor resurgence. The waves reflect the order of the so-called discovery booms, led by uranium, then nickel, and copper, polymetallic base metals and gold. With the possible exception of gold, the discovery booms appear to be independent of metal price, although favorable perceptions of the price outlook may well have initiated the boom or led resurgence. Although difficult to quantify, an emerging trend in modern discovery is the integration of several detection techniques into the search process. No doubt, this trend will continue as orebodies become more and more difficult to find. The record of the past two decades shows that greenfield discovery rates have progressively fallen even though the level of investment in exploration has risen to an all-time high. This trend reflects increasing discovery risk. Several factors are contributing to this trend. Perhaps the two most important are: (1) deteriorating economics as increasing real costs and decreasing real prices continue to raise the economic hurdles for minimum acceptable exploration targets, and (2) increasing exploration maturity in many search terrains, particularly those in the traditional regions of North America and Australasia. To succeed cost-effectively in this new environment of increasing discovery risk will require extraordinary creativity, innovation, and technical skill coupled with commercial discipline."

Jan 1, 2000

By T. Bhambhani, O. Yavuzkan, D. R. Nagaraj

"Cu ore bodies commonly contain oxide Cu at the surface, with sulfide Cu content increasing with depth. The recovery of oxide Cu minerals by flotation is a longstanding challenge in the minerals industry, especially for high acid-consuming ores which would not be economical for direct acid leaching. Current practice of oxide Cu recovery involves sulfidization (often using controlled potential sulfidization or CPS) using NaSH (or Na2S) followed by flotation using traditional sulfide collectors. CPS has shown to improve recovery of oxide Cu but has the following limitations: a) HSE issues with NaSH, b) high consumption of NaSH, and c) inability to recover certain oxide Cu minerals because they are refractory to sulfidization. The oxide Cu flotation is further complicated by the presence of certain non-sulfide gangue minerals which adversely impact both recovery and selectivity.Over the past eight decades, numerous collectors have been proposed and evaluated for the direct flotation (i.e. without sulfidization) of oxide Cu minerals, the most researched of which is alkyl hydroxamate. While there are numerous publications dealing with the fundamentals of interaction of alkyl hydroxamates with single minerals, there are few publications which discuss the practical aspects of alkyl hydroxamate use in ore flotation, particularly their use with sulfidizing agents. Case studies in this paper include methods to identify optimum combinations of sulfidizing agents and oxide collectors to maximize recovery for various types of ores. It was observed that some ores do not require any sulfidization, while others require at least partial sulfidization to improve efficacy of AHX. Depending upon the ore type and mineralogy, recovery improvement in the range of 5 to 15% units, over and above that achieved with CPS, has been observed with the use of AHX. For ores requiring high dosages of NaSH, it was shown that AHX can be used to reduce the NaSH consumption significantly. The challenges associated with the presence of non-sulfide gangue minerals in oxide copper ores are included, and the use of modifiers to alleviate the associated problems and enhance the performance of AHX is discussed."

Jan 1, 2016

By A. C. Bonnier

"INTRODUCTIONI have been asked to make available our method of determining the ""Live Inventory"" within a gravity type thickener. The ""Live Inventory"" being that tonnage compatible with the optimum underflow density that satisfies the process requirements.One prerequisite of the calculations is the proper determination of the final pumpable underflow density. A further requirement is that, prior to shutdown, the thickener has been operated properly, particularly that it has not been operated for storage capacity.Until recently I had few chances to check the method. However, I was most fortunate to have had a recent opportunity covering several months on a 300 ft diameter thickener at a plant in the U.S.A., wherein the method was tested and verified many times. The method proved accurate in that our calculated tonnage checked with the actual dried physical inventory of the drying facility.At the precise moment that the feed to the thickener was shut down, a per cent solid determination was made at the critical place and the tonnage in ""Live Inventory"" determined. Let us say that at the moment the thickener U' Flow solids was 20%. The thickener then was allowed to cperate until the U' Flow solids dropped below 20%, at which time the thickener was deemed to be relieved. Anything much less than 20% was not suitable to the subsequent centrifuge operation.Most large metallurgical thickeners have a configuration of three slopes at the thickener ""bed"". These slopes are dictated by the raking blades and are shown on the manufacturers' erection drawings. The first slope is from the outer periphery and generally takes up a distance of about 60% of the radius, the second slope generally taking up the remaining 40%. Within this 40% area, there is usually another slope taken up by the cone on ""B"" type thickeners or an actual steeper inner slope on ""C"" type thickeners."

Jan 1, 1989

By J. E. Tupper

"This paper will discuss strategies for the introduction of computer technology in the mine environment. More specifically, it will focus on issues such as: (a) make or buy; (b) programmer less mines; and (c) support from corporate groups.The paper relates these strategies to systems for mine operations. These will be illustrated by considering the implementation of some phases of these systems at Teck Corporation.IntroductionThis presentation addresses some of the major considerations in a strategy for mine computerization and then relates these considerations to the computerization cycle and Teck Corporation.Strategy is defined as a conceptual framework or plan to accomplish a goal. For purposes of this paper, the goals can be more simply defined for operational purposes as either increasing revenue or decreasing costs.The strategy will allow us the framework for measuring tactical decisions such as computer and software acquisitions.The Mine Life CycleTo start with, let us look at the mine life cycle from a computer systems point of view:-Exploration-Property Development-Feasibility-Construction-OperationFrom a systems point of view, the exploration cycle is oriented to geophysical and geochemical computing. Property development starts with drilling and building the geological data base. The feasibility cycle includes all stages of evaluating the decision to proceed with mine development: ore reserve calculations; mine planning; and financial projections. Construction includes project management and project accounting systems. Systems required for operation are those needed by personnel at the mine site."

Jan 1, 1982

By I. A. Cameron, F. Ham, R. Sriram

"Planned increases in electric furnace productivity and higher matte temperatures needed for the Sudbury Smelter's S02 Abatement Plan, require an improved matte tap hole. Since startup in 1978, the matte tap holes have been incrementally improved by the addition of copper cooling blocks around the refractory tap blocks. These improvements provided a tap block life of about 100 taps per campaign.In July 1993, a prototype matte taphole was installed in Number 2 Electric Furnace to develop the technology to increase tap hole service life. The design was based on a heat transfer model of the tapping process to determine candidate refractory materials and cooler arrangements. The prototype tap hole features increased copper cooling, high conductivity refractories and extensive instrumentation. Eight trial campaigns are reviewed outlining the performance of silicon carbide and graphite refractories and typical heat loads during tapping.IntroductionFalconbridge Limited operates two 36 MYA, 6 electrode submerged arc electric furnaces in Falconbridge, Ontario. The furnaces, commissioned in 1978, smelt a partially roasted nickel-copper calcine, to produce matte for converting and slag for discard. Additional details of the smelter are available in the literature(1-4).Each furnace was equipped with two matte tap holes located in the furnace end wall. Early in the campaign, matte tap holes were identified as a weak area in the furnace which could be improved. From 1981 to 1987, incremental improvements were made to the design by the addition of water cooled copper blocks. In 1993, a prototype matte tap hole was designed and installed in Number 2 electric furnace to develop the technology to increase tap hole service life. Improved service life is required to meet planned increases in electric fWl1ace productivity and the higher matte temperature needed for the smelter's S02 Abatement Plan.This paper reviews matte tap hole development since 1978; outlines the prototype matte tap hole design, refractory selection and installation; and details the performance of the prototype tap hole during the first eight campaigns."

Jan 1, 1995

By Yongfeng Jia, Shaofeng Wang, Danni Zhang

Ferrihydrite is ubiquitous in soils, groundwater and aquatic sediments and is usually classified as "2-line" or "6-line" according to the number of diffuse XRD peaks. It has high surface area and reactivity; therefore, it may serve as a sink for sequestering trace metals, metalloids and organic matters via adsorption and co-precipitation. Although considerable attention was paid to the transformation process of this thermodynamically metastable solid, there are still some controversies on the mechanisms of the formation of goethite or hematite from the ferrihydrite precursor. This work systematically investigated the transformation of 2-line ferrihydrite produced by using different neutralization regent (CaO vs. NaOH) into crystalline products at different pHs (4, 7 and 8), three temperatures (25, 40, 75 °C) and in different media (sulfate vs. nitrate). X-ray diffraction (XRD), Raman, Fourier transform infrared spectroscopy (FTIR) and chemical extraction were employed to characterize the transformed solids as well as the redistribution of Fe between the amorphous and more crystalline phases. The results showed that the transformation product in nitrate media was hematite (major) and goethite (minor), which was independent of pH, temperature or neutralization reagent. In sulfate media, goethite was the dominant solid under slightly acidic conditions (pH 4) with 6-line ferrihydrite as the intermediate product, whereas neutral to slightly alkaline conditions still favor the formation of hematite. Chemical extraction results indicated that there was only ~3 % of amorphous phase detectable after aging at 25 °C for 280 days at slight acidic pH. In contrast,~70 % of the iron remained as an amorphous phase under neutral to slightly alkaline conditions. The results suggested that the pH as well as the reaction media (sulfate ion) plays an important role in the 2-line ferrihydrite transformation process.

Jan 1, 2016

By Kosei Ishida

To achieve renovation work without noise, the authors developed techniques of manufacturing pre-cut interior finishing components for renovation work. In this paper, to achieve the system of pre-cut interior finishing components, the authors describe a measuring method of reinforced-concrete structure by 3D laser scanner and then describe a method of making a design of pre-cut interior finishing components with the polygon model. Using these two methods, the steps of manufacturing pre-cut interior finishing components consist of the following four steps: First, measure the building shape using a 3D laser scanner. Secondly, integrate a point cloud data and retrieve the markings on the floor. Then, create a polygon model of the building based on the point cloud data. Lastly, make a drywall design using a polygon model. To evaluate the technique feasibility of manufacturing pre-cut interior finishing components, the authors have conducted an experiment of the finishing interior work of the drywall. Using pre-cut interior finishing components, the authors have been able to achieve interior finishing work without noise.

Aug 1, 2013

By Margarete Kalin

Mine Waste Management ?Reduction of Sulphideoxidation or inhibiting weathering of rocks Geologist - broken or ground rocks Hydrologist - sources of contaminants Mining engineer - waste sites Consulting companies - income units People - Ugly, bad, dead Ecological Engineer Landscapes which contain building blocks of an emerging ecosyste

May 1, 2013

By Erwin L. Zodrow

"For 25 chemical elements in electrostatically precipitated fly ash (Lingan coal-fired power station), concentration changes are studied as a function of increasing proportions of fines (ash particle diameter less than 45 micrometres). Elements that are involved when concentrations increase as the proportions of fines increase are likely to escape into the atmosphere. These are Th, U, As, S, P, Sb, Na, Ag, Zn, Pb, Ni, Ba, Sc, AI, Mo (and Bi, Ge, Ga, F and Li), i.e., more or less highly volatilized elements. Of the less volatilized metals such as Fe, Ca, Cu, Ti, K, Co, Mn (and lanthanides), certain portions presumably also escape as stack emissions. Diadochy and spinel formation in bottom slag is presented as an emission-reducing agent for certain metals.IntroductionThe Lingan coal-fired power generation plant, owned and operated by the Nova Scotia Power Corporation, produces annually about 140,000 metric tons of ash (the residual mineral content after burning coal). The tonnage is based on a 15 per cent average ash content of Cape Breton coal.For purposes of this report, samples of the hard, fused slag (bottom slag) that is accumulated at bottoms of boilers, and electrostatically precipitated fly ash (ep ash), were collected and investigated. Bottom slag is a minor component of the produced ashes.The ashes were surveyed and the presence of over 75 major, minor and trace elements is reported. From this survey, 25 elements were selected to establish elemental enrichment/depletion trends when the proportions of the less than 45 micrometre <45µm) fractions in ep ashes increase. The results are significant in that, taking the case of elemental enrichment, the elements involved are likely to escape into the atmosphere, i.e, highly volatilized elements. Depletion trends for elements are presumably associated with less volatilized elements during coal-firing. Quantification of the emission of atmospheric pollutants is not considered part of this work. ""Igneous"" minerals generated during coal combustion include spinels (found mainly in the bottom slag), quartz, glass and mullite."

Jan 1, 1982

By Mehmet F. Taner

"Abstract - "Les Mines Selbaie" is a large, generally low-grade, polymetallic (Zn, Cu, Ag, Au) "giant" volcanic-associated ore deposit in the Harricana-Turgeon belt, which is part of the northern Abitibi Subprovince of Quebec. Economically recoverable mineralization occurred in three zones: the A1 (open pit), A2, and B Zones (underground). The pre-mining resource was 54.9 Mt, including 8 Mt of sub-economic, locally silver-rich massive pyrite. In the Selbaie region, calc-alkaline andesitic volcanics form the "basement." The Brouillan Volcanic Complex formed within an islandarc setting on this regional basement. Evolution of this complex involved the formation of a felsic magma chamber and the development of a large caldera structure over the Brouillan batholith. Second- order linear and sub-parallel faults and rifts developed as a result of back-arc rifting/extension. The edges of these rifts were feeders for linear felsic volcanism (similar to fissural volcanism). During felsic volcanism, the feeder zones acted as conduits for hydrothermal fluids with associated pervasive potassic alteration. The alteration is characterized both vertically and laterally by well-defined quartz, sericite, K-feldspar and/or, locally, biotite halos, to produce a mushroom-shaped morphology. This K-feldspar alteration is not common in most other volcanic-associated ore deposits. Mafic dikes cut all of the geological units and appear to occupy earlier synvolcanic structures. Regional greenschist- assemblage metamorphism and pervasive deformation affect all units. Thrust faults moved part of the Brouillan batholith and basement units over the Mine Sequence. Although there is no relationship between the earlier mineralizing events and these late thrust faults, the thrust faults probably played an important role in location of ore lenses. Three types of mineralization are present: 1) copper-rich veins and hydraulic breccias; 2) disseminated and stringer, low-grade and high volume zinc-copper mineralization; and 3) finely laminated, massive, locally silver-rich pyrite mineralization within structural basins. At the bottom of these basins and at the contact of welded acid tuff (WAT) units, massive pyrite zones are locally enriched in zinc, and contain the possible vestiges of black smoker-like material. The ore metals were probably derived from leached basement andesitic volcanics in a hydrothermal system powered by one or more heat sources within the Brouillan Volcanic Complex. The Selbaie deposits are mainly characterized by: (1) the presence of small volcano-tectonic subsidence basins, which host chemical sediments and volcaniclastic materials; (2) pervasive potassic alteration; (3) locally high-grade silver mineralization (up to 1-2 kg/t Ag); and (4) the presence of random zones of Pb mineralization. The Selbaie deposits can be closely compared with the copper-rich Murgul deposits, which belong to the eastern Pontides metallogenetic province in Turkey. If conventional classification criteria for the volcanogenic massive sulfide deposits (e.g., Noranda, Mattabi types, and recent subsea floor deposits) are taken into account, the Selbaie deposits still exhibit many differences in terms of alteration assemblages, physical volcanology and some styles of mineralization (low-grade and large volume). Consequently, the "Selbaie" deposits belong to a new sub-type of volcanic-associated sulfide deposit, which may be used in future exploration programs."

Jan 1, 2000

By Kiran B. Chaudhuri, Michael Koch, Jorg Lema Patino

"Stricter pollution regulations together with other factors have stimulated interest in the modernization of the traditional sinter - blast-furnace lead operation. In this context, direct smelting methods have again come into prominence. Consequently, the Kivcet Lead Smelting Process, which belongs to this group, has attracted the attention of the lead producers of the world. The Kivcet Process offers the advantage that lead and zinc can be simultaneously recovered in a single furnace unit. KHD Humboldt Wedag A G, Koln, Federal Republic of Germany, has signed a contract with the Sociedad Complejo Metalurgico de Karachipampa of Bolivia for the delivery of a turn-key Kivcet plant, which is expected to be the first plant of its kind in commercial operation. This paper describes the design and expected operating data of the plant."

Jan 1, 1980

By James Tuer, John R. Goode, Jim Cambon

"Hudson Resources Inc. (Hudson) has defined a major resource of high purity anorthosite (calcium feldspar) assaying about 30% Al2O3 at the White Mountain (Naajat) deposit in Western Greenland. Extensive beneficiation and evaluation testwork has shown that the material can be simply beneficiated to produce a feed material ideal for the production of low-alkali E-glass used for making glass fibre. An offtake agreement is in place with a major US fibreglass manufacturer and, subject to the mine construction schedule, shipments are scheduled for late 2016 or early 2017. In parallel with the E-glass program, Hudson has completed an initial program of metallurgical testwork which shows that the White Mountain anorthosite can be processed by hydro- and pyro-metallurgical processes to yield either smelter-grade alumina (SGA), suitable for conversion to aluminium metal, or a high purity, chemical/specialty-grade alpha-alumina (CGA) commanding a premium price. The process includes dissolution of the anorthosite in hydrochloric acid, HCl sparging to precipitate aluminium chloride hexahydrate (ACH), recycle of the ACH filtrate to leaching with a bleed stream processed for HCl regeneration from CaCl2, and two-stage calcination of the ACH to regenerate HCl and produce SGA and/or CGA. Calcium silicate and amorphous silica are marketable by-products. This paper discusses the White Mountain anorthosite deposit; the process testwork completed to develop production processes for SGA and CGA; production plans, and indicative economics.INTRODUCTIONHudson Resources Inc. (Hudson) holds a 100% interest in the Naajat Exploitation Licence in Western Greenland that cover the White Mountain high-calcic anorthosite deposit. Anorthosite is a calcium aluminosilicate of slightly variable composition but generally containing about 30% Al2O3. The alumina content is similar to that in bauxite and anorthosite has long been studied as a feedstock for the production of alumina. Other potential uses include feedstock for the high-end fiberglass (E-glass) industry and as a filler for use in paint and plastics."

Jan 1, 2016

By Greg Johnson

Maintenance needs information about assets to optimize availability and production needs information about performance and consumption to maximize output. In considering both these needs together as, ?Asset Optimization?, the information systems that support them are critical. The theory of Asset Optimization derives from the Lean Manufacturing concepts developed by Toyota, but some changes are required to apply this to mining operations. In particular, mining operations require automated systems due to their geographic spread and they need a strong emphasis on capturing under-performance losses as well as delays and stoppages in production. Leading metal miners and coal miners alike have applied these systems to good effect in the last 10 years. The concepts developed initially in minerals processing plants are now being applied to the mines themsleves as well as the mining logistics chain. Production increases of 5?10% are achievable with the right implementation and consideration of the some key lessons learnt in the last 10 years. Putting these lessons into action is one key step in the goal of optimizing asset performance and thus utilizing the resource at lowest cost.

Aug 1, 2013

By G. Begin

"The expansion undertaken at Selbaie in 1985 necessitated an adaptation and expansion of the equipment maintenance system. This paper relates briefly the stages of transformation of the maintenance administrative structures, work methods and tools. The maintenance in a mechanized mine requires an expenditure level in the order of 20% of the total operating cost of the enterprise. Thus, the maintenance organization was modified to apply more computerized planning and follow-up, and the role of preventative maintenance was further advanced.IntroductionAs far as maintenance is concerned at Selbaie, the scenario described herein is a resume of the current situation. Although positive results have been obtained, this outline is in no way a detailed account of a fail-proof maintenance system.Once zone A-I was put into production, the expansion the mine experienced in 1985 had a direct impact on the equipment maintenance system. As centralized as it was in the beginning, the system is now partially decentralized.The over-all changes to the maintenance department demonstrate the flexibility required by organizations in new situations. In spite of the exceptional results obtained before the expansion, it became evident that both the maintenance and production sectors would have to be combined. In doing so, a more appropriate coordination of maintenance work could be obtained and the maintenance staff would obtain a more detailed knowledge of the equipment in each sector. In addition, by keeping the general and specialized departments centralized, it was possible to offset the negative effect s of a decentralized system, namely too much manpower."

Jan 1, 1990