Search Documents

By D. Tao

Froth flotation is widely used in the coal industry to clean -28 mesh or -100 mesh fine coal. A successful recovery of particles by flotation depends on efficient particle-bubble collision and attachment with minimal subsequent particle detachment from bubble. Flotation is effective in a narrow size range outside which the flotation efficiency drops sharply. A fundamental analysis has shown that use of picobubbles can significantly improve the flotation recovery of particles by increasing the probability of collision and attachment and reducing the probability of detachment. A specially designed column with a picobubble generator has been developed for enhanced recovery of fine coal particles. Picobubbles were produced based on the hydrodynamic cavitation principle. Experimental results with one metallurgical coal and one steam coal have shown that the use of picobubbles in a 2" column flotation increased fine coal recovery by 10-30%, depending on the feed rate, collector dosage, and other flotation conditions. Picobubbles also acted as a secondary collector and reduced the collector dosage by one third to one half.

Jan 1, 2006

By H. H. Bleakney

THIS paper presents evidence that in 3 1/2% nickel steel, the published temperature for the Ac1 transformation, l,275°F., represents the completion of that transformation, and that its inception occurs approximately 275°F. lower, at about l,000°F. The formation of austenite within this range, especially at the higher temperatures, and its subsequent decomposition to martensite, results in considerable impairment of the properties of the steel. That the solid solution found to occur below l,275°F. is austenite has been questioned, but the evidence herewith presented, while not decisive, appears to be reasonably convincing. INTRODUCTION The February, 1939, issue of Metals Technology contains a very interesting paper by I. N. Zavarine, Associate Professor of Metallurgical Engineering at the Massachusetts Institute of Technology. In that paper, Professor Zavarine presented photomicrographs illustrative of the microstructures produced by heating nickel steels to a temperature slightly below the carbon change point, and holding them at that temperature for various lengths of time. His illustrations show that the structures found after such treatment do not consist merely of ferrite and carbides, but are characterized by the presence of a third phase, which he describes as a' 'sub-critical solid solution'. The occurrence of this third phase in increasing amounts is accompanied by an increase in strength and a loss of ductility and impairment of elastic ratio of the steel. Some years ago, one of the authors encountered the above-mentioned phenomenon in treating large forgings of 3.5% nickel steel. After normalizing and then drawing at l,250°F., very poor mechanical properties were obtained. Investigation of the steel disclosed no inferiority in quality. Eventually, after considerable waste of time and money, a draw temperature of l,150°F. was tried. This treatment resulted in a very great increase in elastic ratio, over 5 per cent increase in percentage elongation, and proportionate improvement in reduction of area.

Jan 1, 1941

By Gordon A. Gross

During the last half century major steel industries of the world have become dependent on iron and manganese resources derived from siliceous ironformation sediments. More than two billion years ago vast amounts of iron and manganese were deposited in ironformation sediments on all continents and until recent years their genesis was considered to be a uniquely Precambrian phenomenon. Research work has demonstrated that the origin of the banded ironformations was related to major tectonic features and associated volcanogenic processes that were active throughout geological history. Similar sedimentary-tectonic environments are being explored on the seafloor where metalliferous sediments are forming today. Ironformations are now considered to be a major part of the stratafer group of stratiform metalliferous deposits. They developed in sedimentary basins in areas where deep tectonic fracturing intersected high thermal gradients in the earth?s crust and gave rise to profuse volcanism and the hydrothermal effusive discharge of metals in the vicinity of the volcanic centres. Concepts for the genesis and metamorphism of stratafer deposits as revised in the last half century have had a profound impact in the development of iron ore resources and have had a dramatic impact in the use of metallogenetic concepts for guiding exploration for other mineral resources. They are based on the tectonic history and stratigraphy in the sedimentary basins, the role of hydrothermal volcanogenic processes , as well as environmental and sedimentation factors which influence the deposition of silica, iron , and other metals that were emphasized in the past. Topics of special interest in the genesis of ironformation and stratafer deposits and for guiding mineral exploration are: biomediation in their sedimentation and genesis, the significance of metamorphism in the processing and beneficiation of iron ore and in the genesis of iron ore by natural enrichment processes, syngenetic concentrations of Mn, Ti, Cu. Zn, Pb, Ni, Co, REE, F, Ba, B, As, Hg, W and Au in ironformations and stratafer lithofacies, and the mobilization of gold and other elements by alkaline solutions during diagenesis of ironformation and other stratafer metalliferous sediments.

May 1, 2003

By L. Vinnett, I. Panire, J. Yianatos, F. Ruiz

"The effect of operating variables on the flotation performance at steady-state has been extensively used for modelling and simulation of separation processes. However, the dynamic characterization of key variables such as gas dispersion (Sauter mean diameter of bubbles, D32, and bubble surface area flux, SB) and froth discharge rate is rather scarce. In this paper, an experimental design allowed identifying the dynamic response of the flotation process in a laboratory scale flotation cell, using a two-phase system, airwater. The installation included automatic control for the superficial gas rate, JG, and the pulp level. Gas dispersion was evaluated in terms of the Sauter mean diameter of a bubble population and the bubble surface area flux, SB = 6·JG/D32. The D32 was measured using the McGill Bubble Size Analyzer (MBSA) along with a semiautomated algorithm. In addition, the froth discharge velocity was measured in real-time using a Visiofroth system. The control variables were the superficial gas rate and the frother concentration (Teefroth). The dynamic characterization of the flotation process is useful to design algorithms that allow the direct or indirect control of metallurgical variables such as flotation rate, concentrate grade and mineral recovery.INTRODUCTIONGas dispersion indicates the way the gas entering a flotation machine is dispersed throughout the volume of the equipment (Schwarz & Alexander, 2006). The gas dispersion is typically characterized in terms of the bubble size (dB), gas holdup (eG), superficial gas rate (JG), and bubble surface area flux (SB =6·JG/dB) (Finch et al., 2000). All these variables have significant impact on the metallurgical performance of flotation machines. For example, Perez-Garibay et al. (2014) investigated the effect of the particle size, bubble size distribution, superficial gas rate and collector dosage on the flotation performance, for the separation of a sphalerite mineral. The authors observed that recovery increased with the superficial gas rate ranging from JG = 0.04 to JG = 0.08 cm/s and also a maximum recovery was obtained for bubble size close to 300 µm. Gorain et al. (1998) reported a strong correlation between the flotation rate constant and the bubble surface area flux in a zinc cleaner circuit. Both variables were directly proportional at three froth depths in the range of hF =7 - 45 cm. Dobby & Finch (1986) incorporated the effect of the superficial gas rate and the bubble size on the flotation efficiency by means of a kinetic model for the rate constants. Yianatos & Contreras (2010) developed a model to estimate the carrying capacity in large flotation cells by including the bubble surface area flux."

Jan 1, 2016

By V. G. Papangelakis, M. Cheung, M. Dry

The high pressure acid leaching of laterite was modelled and simulated using a combination of two commercially available software packages, namely Aspen Plus 11.1 and the OLI Stream Analyzer. New kinetic parameters for the acid-controlled metal dissolution and precipitation reactions at temperature were first determined from previous experimental data on the leaching of limonite. A grain model with cylindrical pellets was used to model the solid-liquid dissolution reactions. Precipitation reactions were modeled via aqueous equilibrium chemistry. A dedicated thermodynamic database previously developed at the University of Toronto was used in conjunction with the OLI software to model the solution chemistry and calculate the concentration of hydrogen ions in solution at the leaching temperature. Mass balances were handled by Aspen Plus. The simulation gave good predictions of nickel dissolution under industrial and laboratory conditions, for the dissolution of limonite and limonite/saprolite blends. Computational

Jan 1, 2005

By R. Guimarães, L. Silva, J. Milboume

The São Bento concentrator was built by Gencor in 1985 to treat refractory gold-bearing flotation concentrate. The plant was the first commercial application of pressure oxidation for refractory gold ore following about a year after the first use of pressure oxidation on a whole ore at Homestake's McLaughlin operation in California. Ore from the Sao Bento mine is remarkably consistent in gold grade and arsenic and sulphide concentration as is typical in banded iron formations (BIF) (l). Gold content is approximately 9 g/t with approximately 30 - 40% free milling. The balance is associated with arsenopyrite and pyrrhotite. An expansion of both process facility and mine was undertaken between 1996 and 1998, raising the treatment capacity from 32,000 t/mo to 45,000 t/mo.

Jan 1, 2004

By R. Khettabi

The mechanical, thermal and bioproperties of titanium alloys allow their wide use in different industries. Compared to aluminum alloys, titanium alloys are very tough, making them that much more difficult to machine than aluminum alloys. Most studies conducted on these types of materials have mainly covered and made comparisons in terms of cutting speed, cutting force and mechanical properties. Recently however, their sustainability and environment parameters have begun to attract significant interest, and it has been found that machining processes generate particles that can be harmful for health and the environment. In this paper, particle emission is investigated during the turning of the titanium Ti6A14V and 6061-T6 aluminum alloys.

Jan 1, 2011

By S. J. Cook

The system of mining statistics for Canada, as it exists today, represents the result of long years of progress, first by the Geological Survey, later and more comprehensively by the Mines Branch of the Department of Mines, and now by the Mining Branch of the Dominion Bureau of Statistics-all supplemented by the very comprehensive reports published by the several provincial departments of mines. It is the purpose of this paper briefly to state the development and present status of Canada's statistical service, more particularly in regard to information on mineral production, and to show that in its evolution continuous progress has been made in the elimination of factors tending to duplication and overlaping, with the result that the construction of an adequate statistical service has been carried out with the least possible expenditure of .public funds. For the purpose of this discussion, the subject of mineral statistics may conveniently be considered from two points of view. The technical difficulties in obtaining satisfactory and complete data from the variety of industries represented in the mining fields of Canada must be apparent to all. Methods of record-keeping are almost as numerous as mines and even the larger concerns which maintain elaborate records for their own information, often find it difficult to compile the statistical reports required of them, because the specific form of inquiry differs from the method in use in their offices.

Jan 1, 1924

By J. A. H. Church

My paper entitled "Spontaneous Combustion of Coal in Mines;" read some time ago before this Branch, consisted chiefly of extracts from the British Blue Book dealing with the same subject. Fallowing my article, Mr. de Hart submitted a paper dealing with the application of existing methods of working in Alberta to the conditions obtaining in our bituminous mines. I must confess that the perusal of his paper did not enlighten me either as to what might be a method preferable to those in vogue or even to Mr. de Hart's ideas on the subject, nor did the ensuing discussion of Mr. de Hart's paper afford any great clarification of the problem. The outstanding idea, supplied by Mr. Dick, seemed to be that a retreating system could not be employed, as no operator would feel justified in risking the capital necessary to driving to the boundary when the whole might be jeopardized by a fire breaking out in the waste. That a fire would break out in the waste of any adit-level working seemed to be conceded by all, and with that I agree; that an ignited waste could not be safely sealed off by means of stoppings in a coal barrier-pillar appeared to be the contention of Mr. Dick, or perhaps he attributed this idea to the Mines Branch-anyhow, it seemed to loom over the discussion like a miasma. With this aspect I do not agree, as ? reliance is placed wholly on stoppings in the thick seams of South Staffordshire, even in fiery mines. In the thick coal at Exhall colliery, or elsewhere in Warwickshire (34 feet 4 inches) containing hard and soft coal in layers, a fire assuming serious proportions is sealed off. By the way, retreating long-wall methods are employed. In Fifeshire, sealing off fire in the Dysart mine has been accomplished successfully. The seam averages about 20 feet thick.

Jan 1, 1924

By C. M. Campbell

IN 1934 Newfoundland, after extravagant operation based on exaggerated ideas of what she had to work with, became bankrupt, ceased to be a self-governing Dominion, and passed into the hands of a Commission. Since the days of Dawson, Canadians have been taught that no country in the world is as rich as their own. This idea has become a religion; contrary views are heresy, and are suppressed even by technical organizations and government departments. Following the alleged habit of the ostrich, we have buried our heads in the sand and have refused to face the facts. This policy of "to have today and to hell with tomorrow" is now bearing fruit. After forty years of operation on the basis of unlimited natural wealth, with resulting over-expansion, wholesale depletion of capital assets, and huge borrowings, we are, now that our wealth has been shown to be very limited, face to face with the status of Newfoundland. Already, in this Province, commission government of bankrupt municipalities is not uncommon. The ostrich is referred to as the most foolish bird in the world. That is not the case-no ostrich ever hid his head in the sand. In the clear air of his home on the South African veldt, an area characterized by low bushes, he is a conspicuous object. When danger approaches, he lowers his head; matches his background, the bushes; and danger passes him by. This leaves the Canadian, with his head still in the sand, to fill the r61e cast for the ostrich. Fortunately, a few Canadians never did get their heads covered; others are getting them out far enough to see what is going on. Their comments are very much to the point. "Nowhere in the world," says Mr. Meighen, "has more harm been done to any country by an exaggeration of its resources and potentialities than has been done in Canada'.

Jan 1, 1941

By O. Schnake, M. Isakson, C. A. Landolt

The paper presents the conceptual basis for the development of an Activity Based Costing system (ABC) for the analysis and estimation of process costs in mining and metallurgy. In particular, it discusses three major thrusts towards attaining increased efficiency in extraction and processing systems: (a) understanding the link between process and expenses, (b) identifying the chemical and physical factors that govern process costs and ( c) using process and cost models of the production systems. The authors have developed computer techniques to analyze data from conventional accounting and apply them to the development of process based ABC systems. The cost causing activities are linked to management units patterned after the organizational structure of the production system. All costs are associated with specific process functions such as charge preparation, smelting, refining, etc. The level of detail is determined by the quality of data available in conventional accounting systems. The system permits data analysis of historical cases and the projection of costs for new production schemes. Results can be presented in various levels of aggregation, following organizational and/or functional structures. The outputs of the system are tabular and graphical, typically following Pareto analysis concepts.

Jan 1, 2007

By F. Richards

"The property of the Cariboo Gold Quartz Mining Company; Limited; is in the Wells-Barkerville district of Cariboo mining division. It consists of a group of 106 Crown granted mineral claims and fractions; and extends for over 6 miles along what is termed the Barkerville gold belt. The main portal and mine camp are half a mile south of Wells; which lies at the northeast end of Jack of Clubs lake and is reached by a 55-mile motor road from Quesnel; the northern terminus of the Pacific Great Eastern railway.Gold-bearing quartz veins were discovered on the surface in various parts of the property by different prospectors as far back as 1877, but the work that led to the formation of the present company was performed by Al Sanders in the year 1926. Sanders dug trenches and drove small adits on quartz veins containing gold above what is now known as the Sanders zone. Very little underground work has been done beneath the earliest known discovery-the B.C. vein. The Cariboo Gold Quartz Mining Company was formed in the autumn of 1926. The total production of gold from its beginning in 1933 to the end of 1944 has been as follows:"

Jan 1, 1954

"One of the corporate values mentioned by many companies deals with respect for people. This paper discusses one aspect of this value, namely, the need for clarity of accountabilities and authorities. The job of the manager in achieving this goal is analyzed and the benefits of enhancing the manager-employee conversation outlined. IntroductionCorporate values usually refer to the standards of behaviour that the leaders of the organization expect of all employees, including themselves, in carrying out their duties. Terms such as integrity, respect for the individual, continuous improvement, continuous learning, teamwork, speed, and innovation are quite common. The company-specific values are typically developed by the top executives of the company, and then tested with a broader group of employees. Where the process works, employees have a good understanding of what behaviour is expected of them in doing their work, in making difficult decisions, and in interacting with others.Having spent considerable time in his career investigating and studying the management systems at over 50 of the most successful companies in Canada, the United States, Europe and Japan, the author has had the opportunity to visit organizations such as Hewlett-Packard, 3M, Xerox, Intel, Toyota, NEC, Komatsu, British Airways, and Eastman Chemical. These experiences, together with the work of many other researchers, including the work of Dr. Elliott Jacques, have helped significantly to form the thoughts expressed below.Rather than reviewing the creation of corporate values and their deployment through the organization, these remarks focus on issues over which managers and employees have some control. The value in which managers can have significant impact deals with people and the respect shown them in the workplace. The component of respect to be emphasized is to be clear about expectations or accountabilities for oneself and the people who report to you, and to ensure that personal authority matches those expectations."

Jan 1, 1999

By D. R. Murray

A four-year study was carried out to determine the ability of coniferous trees to aid in the reclamation of uranium tailings at Elliot Lake. Five species were planted: white cedar, white spruce, jack pine, scotch pine and red pine. More than 570 bare-root, two-year-old seedlings were planted on bare tailings and in areas of established grasses. A further division was made between areas of coarse and fine tailings. Over-all survival and growth of the trees has been far below expectations based on previous experience with several varieties of grasses. The criteria for assessment have been per cent survival and yearly growth as determined by plant height. Pine was superior, with 68% survival when planted in bare coarse tailings, 45% for vegetated coarse tailings and 34% for vegetated fine tailings. Cedar had the worst survival rates at 49%, 14% and 7% respectively. No species survived on bare fine tailings. The survival and growth of the coniferous trees have been related to species, environmental conditions and tailings properties.

Jan 1, 1978

By R. Loney, M. Militzer

There is a significant demand for new high strength steels with fine grain sizes for structural applications. One approach in this regard is to develop hot-rolled HSLA steels where refining the microstructure leads to increased strength levels, e.g. 700 MPa yield strength, that can be attained by suitable modifications of chemistry and processing. Here, an HSLA steel is investigated that contains 0.05wt%C-1.65wt%Mn-0.20wt%Mo¬0.07wt%Nb-0.02wt%Ti and approaches the above strength class. The ability to control and predict the mechanical properties of hot rolled steel depends strongly on the thermomechanical processes, which the steel undergoes. The final microstructure and, thus, the properties of the hot-rolled steel are a function of the austenite decomposition obtained during accelerated cooling on the run-out table and precipitation during coiling. The austenite-to-ferrite phase transformation under run-out table conditions has been investigated using a Gleeble 3500 thermomechanical simulator equipped with a dilatometer. The effects of cooling rate and initial austenite microstructure including the degree of work hardening on austenite decomposition kinetics and ferrite grain refinement have been quantified. Results show that grain refinement can be optimized by the presence of work hardened austenite and accelerated cooling. Based on the experimental results, a model is proposed to predict the transformation start temperature and the resulting ferrite grain size for run-out table cooling conditions.

Jan 1, 2004

By N. Vayenas, G. Yuriy

"The combination of a predictive reliability assessment model and discrete-event simulation can be an effective methodology to study the impact of equipment failures on the capacity of production systems in mines. In our case, a predictive reliability assessment model using genetic algorithms is combined with a discrete-event simulation model to analyze mine equipment systems.Discrete-event simulation involves modelling of real-life systems based on variables and events that occur or change at distinct points in time. The Simul8 simulation software, by Visual Thinking, is used in this research. It is a two-dimensional (2D), discrete-event simulation/ animation software tool for creating realistic depictions of manufacturing and materials handling systems.The simulation model developed for the purpose of this research represents a typical two-level, sub-level stoping section of an underground mine in the Sudbury region in Ontario, Canada. This 2D model was created to assess the impact of equipment failures to a mine’s production throughput. In more detail, using mean time between failures (MTBF) data of scooptrams derived from a reliability assessment model based on genetic algorithms, LHD failures are incorporated into the simulation model. These failures cause production interruptions to the development cycle and consequently loss of hauling capacity.Another purpose of this research work is to demonstrate how low-cost simulation tools such as Simul8 can be successfully applied to model underground hard rock mining operations. The research discussed in this paper is carried out by the Laurentian University Mining Automation Laboratory (LUMAL)."

Jan 1, 2005

By The Satff

"TEXADA Island is situated in the Strait of Georgia, about 100 miles northwest of Vancouver. The property of Texada Mines Ltd. lies on the southwest coast of the northern end of the Island. A part of the ""Sunshine Coast,"" the climate is moderate, with about 30 inches of rain during winter months and relatively dry summers. Texada has been shipping high-grade magnetite concentrate continuously since 1952 to Japanese ore buyers. In 1959, a 3,000-foot tunnel was driven just above sea level to explore the possible downward extension of known orebodies then being mined by open pit. In January of 1961, because the open-pit operations had a limited life, C. C. Huston and Associates were brought in as mining consultants to do a feasibility study on the possibility of going underground for production. This study was completed in March, 1961. With the completion of the report, the Company went to Japan seeking a ,long-term contract to justify the capital outlay necessary for setting up an underground operation. Concurrently, underground diamond drilling revealed more ore, and the Company planned some modifications to the concentrator for increasing the copper recovery. By November, 1961, a ten-year contract was signed with Japanese ore buyers for the sale of 450,-000 long tons of concentrates beginning in October, 1963. Since that time, the Company has built its own 65 000-ton ore carrier and an additional three-year contract has been negotiated, with an annual tonnage increase of from 450,000 to 550,000 tons."

Jan 1, 1967

By N. Musee, N. Kornelius

This study presents a neural network approach to modelling the liberation of gold bearing ores. A complete mineralogical analysis of unmilled and milled ores, including gold deportment and gangue content are used as inputs to a self-organising neural net which generates order preserving topological maps. The arrangement and shapes of these clusters are coupled to unmilled free gold data to predict gold liberation in milled ores (absolute error: 4.2%). Moreover, the self-organising maps were diagnostic of the quality of data used, indicating that the relationship between particle size and gangue material content requires further investigation.

Jan 1, 2005

By A. C. Stevenson

"The most common theory is that, since thyristors, diodes, and insulated gate bipolar transistors (IGBTs) are “solid state” they will live forever. This is not so. They have wear-out mechanisms (e.g. insulation) and other mechanical parts such as motor bearings. These wear-out phenomena can be easily calculated. In this paper we will look at some of the failures and the failure rate of thyristors in power converters to see what affects them and to see what improvements can be made. If converter failures do occur, some simple forensic engineering steps will show if this is the root cause of the problem.IntroductionLook at the general failure rate curve for thyristors, diodes, gate turn off devices (GTOs) and IGBTs shown in Figure 1. We see that there is an initial high failure rate due to manufacturing defects, application problems, and drive start-up stresses that lasts for a few weeks. This is followed by a long period of (hopefully) several years with a relatively low but very slowly rising failure rate. At the end of this period, the devices start to wear out and the failure rate suddenly starts to increase rapidly over a few months. This signals the end of life for the devices in the system. We will start by looking at this end of life area."

Jan 1, 2000

By P. Abachi

Cemented carbides or hard metals that generally consist of hard tungsten carbide and a tough metal binder such as cobalt are important in many segments of the world economy, ranging from automobile related components to machining, cutting, and drilling tools. For metal cutting operations such as turning and milling, replaceable cemented carbide inserts are frequently used. The exposure of inserts to very severe conditions (e.g. temperatures as high as 1000°C) in combination with very high loads, limits their lifetime. When the tools and components are scrapped, they are collected with a view to recovering the tungsten carbide and cobalt due to both their environmental aspects and their strategic importance. In this work, a selective electrolysis process was used for recovery of WC powder particles from cemented carbide scraps. The WC-10Co and WC-10Co-VC up to 3 wt.% VC was produced using powder metallurgy route. The mean particle size of WC, Co and VC were selected as 2.5, l.5 and 2.2 µm respectively. Referring to electrochemical curves of WC-10Co cemented carbides in hydrochloric acid solutions with different concentrations, the recovery rate was enhanced in IN acid. Therefore, this solution was selected for recycling of all samples. The surfaces of as-produced and corroded specimens were investigated using a scanning electron microscopy (SEM). Detection of corrosion products was provided by energy dispersive spectrometry (EDS). According to results, the selective electrolysis process could be useful in the recycling of scrap carbide materials, although more studies should be undertaken on economical aspects of the process and the quality of samples produced using recovered powders.

Jan 1, 2005