Search Documents

By A M. Goodwin

Detailed stratigraphic studies in the Birch-Uchi Lakes area have shown that the volcanic components are arranged in superimposed sequences, or cycles. Each cycle displays a progression from predominantly mafic effusives below to predominantly felsic extrusives above. Sedimentary rocks are preferentially associated with the felsic extrusives. Two volcanic cycles are represented. The average stratigraphic thickness of the volcanic rocks present is 31,000 feet. The original volcanic pile was probably in the order of 40,000 feet thick. The present lithologic composition is estimated to be: mafic volcanic rocks, 60 per cent; felsic volcanic rocks, 27 per cent; sedimentary rocks, 10 per cent; and others, 3 per cent. Gold occurrences are preferentially distributed with respect to the volcanic succession. Of fifty recorded occurrences, thirty-nine are located in the upper felsic division of the lower volcanic cycle; forty are associated with closely interbanded daciterhyolite pyroclastic rocks, andesitic lavas and siliceous sediments. The gold-bearing quartz veins either lie at the contacts of enclosing lithologic units or occupy cross-cutting fractures in one or more adjacent units.

Jan 1, 1965

By Heather Budney

Objectives 1. Evaluate the effectiveness of ON?s EA processes using criteria from the EA and policy sciences literature. 2. Recommend improvements to the EA processes and draw lessons from the ON case for the consideration of other jurisdictions. Evaluation Process 1. Chose criteria ? 14 primary criteria (Wood 2003) ? Subcriteria from Wood (2003) and Lasswell (1971) 2. Gathered information ? 6 key informant interviews ? Published literature, policies, legislation 3. Assessed criteria and formed Recommendations

May 1, 2008

By A Falter

Gyroscopic surveying instruments, which apply the physical law of a gyroscope, are being used for deter-mining the azimuth of lines with a high degree of ac-curacy. In the past ten years, gyro-theodolites have been introduced widely for underground orientation in the mining industry of Russia, Germany and South Africa. Gyroscorpic methods eliminate awkward procedures of conventional shaft plumbing, and provide more safety, excellent control and the highest precision at any point under-ground without interference with hoisting operations. The advantages of gyroscopic orientation in geodetic surveys become obvious in primary and secondary triangulation, in the determination of co-ordinates of single triangulation points, using the method of trigonometric re-section and intersection, and when traversing over long distances or in areas with obstructed view. Other fields of application are found in geophysical surveys and in the orientation of technical objects; e.g. radar stations, relay stations and ballistic missiles.

Jan 1, 1964

By Xiaoqiong Wang, Daobing Wang, Fanbao Meng, Jianbo Wang, Hongkui Ge

"Shale gas has become an important unconventional oil and gas resources. Its effective development relies on comprehensive and accurate understanding of shale gas reservoirs. Rock mechanical properties is one of the important components of reservoir evaluation. Two adjacent black shale samples, which are cored from the depth of 1145 meters in Chongqing, southwest China, are subjected to acoustic emission(AE) test under uniaxial stress and compared with coarse grained granite. The results of synchronous AE, stress-strain and ultrasonic velocity experiments show that shale has weak anisotropy. Compared with granite sample, two shale samples are similar, but their strength, velocity and brittleness are quite different, indicating that shale has strong microscopic heterogeneity. TOC, XRD, SEM microstructure analysis show that total organic content, mineral composition and natural fractures are the main impacting factors for mechanical heterogeneity. INTRODUCTIONShale gas is a typical low-grade marginal resource, which is characterized by ultra-low matrix permeability and small single well control volume. In order to enable commerical development, complex hydraulic-fracture networks must be created in the shale to allow gas to escape from the micro/nano-pores and natural fractures where it is trapped in the rock (C. Clark et al.,2013; Ge et al., 2013). The development of shale gas requires accurate evaluation methodologies to evaluate shale reservoir properties and predict production. (Jarvie et al., 2007). Rock mechanical properties are an important part of the reservoir evaluation. It is significant for efficient drilling, completion and hydraulic fracturing to understand mechanical behavior of shale gas play (John, 2011; Wei, 2013).Rock mechanical properties mainly include heterogeneity, anisotropy, brittleness and acoustic emission activity (Lockner et al., 1992; Jerome et al., 2009; He et al., 2010; Liang et al., 2012). Shale mechanical properties are evaluated from laboratory tests following a complex workflow that covers tasks from sampling to testing (Md. Aminul Islam et al., 2013). It is common to include various experimental methods such as stress-strain curves, ultrasonic velocity and acoustic emission when evaluating the mechanical properties (Rao et al., 2006). Because of the presence of organic-rich matter, mineral composition orientation and natural fractures, shale tends to have strong anisotropy and heterogeneity (Deng et al., 2004; Wang et al., 2013; Hathon et al., 2013)."

Jan 1, 2015

By Chas Kemsley

NO. 6 shaft at Dome Mines, Limited, is an internal shaft going down vertically from the sixteenth, or 2,000-ft., level to the twenty-ninth, or 4,000-ft., level, with loading station and sump below this. It is located approximately 4,600 feet east of No. 3 shaft, the latter being Dome's main shaft through which ail ore, men, and material are handled. The decision to sink this shaft was made in May, 1935, and work was commenced almost immediately. To reach the site of the new shaft, 3,100 feet of cross-cutting, and 1,400 feet of slashing to widen existing cross-cuts, was necessary. On account of the long haul and the large amount of material to be handled, trolley haulage was decided upon and installed as soon as possible to facilitate the removal of waste rock from the crosscut and other necessary excavations. Figure 1 shows a cross-section of the cross cut and the manner in which the trolley wire is supported and guarded. For hanging each individual cross-piece, two holes are drilled into the roof and filled with snug-fitting wooden plugs. Into these, %-in. ragged hanger bolts arc driven by means of a stoper. The bolts are of various lengths to allow for irregularities in the face of the rock, and they have sufficient thread to permit several inches of adjustment for proper alignment of the cross-pieces. These hangers are spaced at 8-ft. intervals except at the curves, where 5-ft. spacing is used. A 2 in. by 6 in. cedar plank is fastened to the cross-pieces directly over the centre of the track. To this the trolley-wire supports are bolted, and 1 in. by 10 in. cedar boards are nailed on each side to act as guards. Two power-supply cables, one telephone cable, and one .Y2-in. conduit lighting circuit are also supported on the trolley-wire hangers, as shown in Figure 1. A 20-in. ventilating pipe and a 10-in. air line are placed as shown, thus acting as a guard to prevent workmen from walking on the track.

Jan 1, 1938

By P. Groleau, O. Tavchandjian, D. Marcotte

In open pit mining, each small mining unit (SMU) is selected for mill processing based on an estimate of its true grade. The estimation is usually done using analyses of cuttings from blast holes within that SMU. One common estimator used for selection is the arithmetic average of within-SMU samples. This estimator is conditionally biased. The effect of a conditional bias is to overestimate the profit really recovered from the deposit. For this reason, a conditionally unbiased estimator is preferable. Increasing the number of samples generally improves the accuracy of the estimation (and diminishes the conditional bias, if present, of most estimators). However, there exists a practical limit where an additional sample does not improve the estimation sufficiently to cover the expense of making the analysis. This limit is specific to each deposit and depends on geostatistical parameters, economic factors, and mining parameters. This study examines how the number of samples affects the recovered reserves and the resulting profit. Also, the effects on optimal profit of varying the different factors are examined. Globally, the number of samples required increases with the selectivity of the operation. For a given ore deposit, the greater the number of SMUs selected for processing, the fewer samples are required and vice-versa.

Jan 1, 1998

By Paul Clayton

Case Study ? Site: BMA Saragi Coal Mine Queensland Australia ? Model: Marion 8050 ? YOM: Mid 1970s ? Boom: 97M ? Bucket: Original capacity of 100 Tonnes upgraded to 125 tonnes at time of filtration upgrade. ? Apps: Swing, Hoist & Drag Gearboxes ? Oil: Oil Castrol Alpha TT1200 Viscosity of 1208 cSt @ 40° C (104° F) 720ltr Oil Volume Trial and Installation Justifications ? To reduce gearbox overhauls. Typical schedule being 5 years. ? Bucket upgrade from 100 tonnes to 125 tonnes. Increased gearbox demand and stress. ? Increase of overhauls out to 10 years + ? Saving per Dragline estimated to be US$8-10M in downtime and maintenance if successful. ? In compliance with BHPBilliton Global Maintenance FLAC program ? Fuels, Lubricants, Air and Coolants ? Cost Justification ? Downtime: 4 days ? Lost production: $420,000 ? Cost of parts: $162,000 ? Labour and misc: $41,000 Gearbox failure cost $623,000

May 1, 2008

By N. Saracoglu, J. P. Golightly, R. H. Wallis, J. J. Brummer

"The McClean uranium deposits are in northern Saskatchewan, 11 km west-northwest of the Rabbit Lake mine. Their average grade is 1.8% UJ0 8 and they contain 6,350 tonnes of uranium oxide in seven pods of variable grade and mineral assemblage. They are hosted by both basal Athabasca Group and the regolith developed on the underlying crystalline basement. The major mineral facies are: sulphide, arsenide, 'bleached', and hematite, with the important uranium minerals being coffinite, uraninite and pitchblende.Abundances of carbon and sulphur isotopes are consistent with their derivation from pyritic graphite in basement gneisses. Isotopes of oxygen and hydrogen suggest mineralizing fluids were aqueous and at temperatures of about 200°C. Ar39/ Ar40 laser age determination of illite indicates mineralization began about 1300 m.y, ago and that significant hydrothermal alteration ceased about 1170 m.y. ago though Pb/U data suggest the deposits continued to evolve into the Mesozoic.The deposits are interpreted as the result of oxidizing ground water stripping uranium and other metals from either the Athabasca sandstone, especially the heavy mineral layers, or from the regolith, and precipitating these when encountering a warm reduced fluid emanating from the basement."

Jan 1, 1984

By Harold L. Gibson, David H. Watkinson

"Volcanogenic massive sulphide deposits of the Noranda Camp cur throughout the Noranda Shield Volcano but are concentrated and along the margins of the Noranda Cauldron. The deposits are realized along synvolcanic faults that also accommodated subsince and controlled the location of eruptive centres. Deposits within e 3 000 m thick Mine Sequence formed during a period of active volcanism and subsidence coinciding with the onset of two cauldron subsidence cycles. The Noranda Cauldron was a restricted site of 10malously high heat flow and structural permeability that favoured e development of a high-temperature hydrothermal system. Metals may have been derived from leaching of aquifer rocks by convecting a water or directly from a shallow underlying magma chamber, now presented by the Plavrian Pluton, that was at its highest position !thin the crust during cauldron subsidence. The deposits formed rough a combination of sulphide precipitation from exhaled fluid td replacement at and below the seafloor in a manner analogous to ose on the modern seafloor.RESUMESi les dépôts de sulfures massifs volcano gènes du camp minier de ~uyn-Noranda sont présents dans les différentes parties du volcanluclier de Noranda, ils se trouvent concentres toutefois, en plus ·and nombre, sur le pourtour de la caldeira (cauldron) de Noranda. ~s dépôts sont localises le long des failles synvolcaniques qui ont cilite la subsidence et contrôle la position des centres d’éruption.~dépôts situes dans la séquence des mines (3 000 m d’épaisseur) sont formes durant un épisode d' activité volcanique et de subsiden qui coïncide avec l' amorce de deux cycles d' affaissement de la rldera (cauldron) de Noranda. Celle-ci Jut le site exclusif d’unflux : chaleur anormalement élevé et d’une perméabilité d’origine cucturale qui ont favorise le développement d’un système hydrothermal a haute température. Les métaux proviennent soit directement d’une chambre magmatique situee afaible profondeur, so it d’un lessivage des roches de l’aquifère par l’eau de mer circulant par convection. Cette chambre magmatique, représentée maintenant par le pluton de Flavrian, se trouvait à son niveau le plus élevé dans la croute au moment de l’affaissement de la caldeira (cauldron). Les dépôts se sont constitués par un mecanisme combinant remplacement et précipitation de sulfures à partir des fluides exhalatifs, au niveau ou au-dessous du plancher océanique, de la même manière que se forment de nos jours, les dépôts de sulfures massifs au fond des océans."

Jan 1, 1990

By Darren Medd

Kumtor Gold Company (KGC) currently operates the 500,000 tonnes per day Kumtor open pit gold mine located in the Issyk-Kul region of the Kyrgyz Republic at an elevation of more than 4,000 m. To supplement the open-pit mill feed with high grade underground ore from outside the current pit limits, KGC started pre-production design and development of the underground mine for the SB ore zone in late 2006. The initial phase of pre-production development consists of exploration and haulage declines which, upon completion, will provide ventilation and access to the underground mine. Design and construction of these declines presented many challenges to the project team considering the mines unique location at high altitude, the limited experience with Western underground mining techniques in the Kyrgyz Republic, and the impact of the nearby Davydov glacier and resultant ground conditions. Completion of the exploration and haulage declines was undertaken jointly by KGC and mine contractor, J.S. Redpath Limited (Redpath). The initial phase of development including several ground falls provided detailed information on geotechnical ground types and conditions that were useful in determining the overall mine design and methodology for production. This paper covers the various aspects of the design and construction process of developing the declines under the glacier, minimizing the likelihood of further ground falls, and the journey of both KGC and Redpath which led to the successful breakthrough between the declines on 01 July 2012.

Aug 1, 2013

By A. Luckita, A. Samtani, R. Barus, J. R. Donald, J. Syarifuddin

In conventional Rotary Kiln-Electric Furnace (RK-EF) laterite nickel processing, management of dust continues to be problematic. A more efficient processing of dust represents an opportunity for energy efficiency, increased production, and productivity. PT International Nickel Indonesia (PTI), together with Vale Base Metals Technology Development (VBMTD), has successfully developed and implemented a novel flowsheet enhancement that capitalizes on these opportunities. In the novel flowsheet, the dust recycle stream is moved forward in the RK-EF laterite nickel smelting process. The dust is injected into the kiln's main burner, as opposed to being recycled to the dryers. A similar treatment of dust is commonly practiced in the cement industry; however, application to nickel smelters has not been fully developed to date. This paper describes this dust insufflation technology, the process through which it was developed for laterite nickel processing, and summarizes the lessons learned. A key conclusion is that successful new technology development requires a multi-disciplinary team involving members from research and development, study management, engineering consulting firms, project implementation management, process technology and operations.

Jan 1, 2011

By A. L. Nunes, J. R. E. Garcia, G. Silva, U. Prasad, C. Rabe

"Drilling through the Guayabal shales, a gray calcareous shale, and the C1 to C100 formations, a well-cemented calcareous-sandstone in Corralillo field, Mexico, is a challenge due to severe wellbore instability problems. Additionally, there has been a history of ineffective reservoir stimulations by hydraulic fracturing. To predict and mitigate these subsurface issues, it is essential to characterize the mechanical properties and rocks strength for a better prediction of borehole stresses and collapse pressure during drilling. Various correlations can be used to estimate and/or determine the unconfined compressive strength but most of them are based on transit time and porosity.In this study, grain size distribution was combined with acoustic travel time, porosity and static Young’s modulus to develop a rock strength prediction model for the turbiditic sandstones of the Chicontepec basin. The main reason this combination of parameters was employed was because of the wide variations in rock strength estimated using traditional porosity-based correlations such as the McNally’s (1987), GMI-Jizba-E’s and Bradford’s (Bradford et al., 1987).To develop a new correlation, a geomechanical and microstructural campaign was initiated. Mineralogy by X-ray diffraction, pore and grain sizes by petrography, clay distribution by SEM and porosity by mercury intrusion porosimetry were measured. Static and dynamic Young’s moduli and Poisson’s ratios were acquired by triaxial and ultrasonic measurements on undisturbed sandstone samples from the Chicontepec basin. More than ten offset wells with wireline data, including transit time, porosity, density, resistivity and gamma ray, were used for reservoir and geomechanical characterizations.Our analyses lead us to propose a new correlation for predicting the uniaxial compressive strength (UCS) of sandstones of the Chicontepec Basin as a function of transit time and grain diameter, both of which can be derived independently from destructive laboratory tests. Our results also highlight the importance and value adding of a combined approach incorporating grain size analysis in the rock strength prediction. The UCS predicted using the transit-time and grain-size-based model presents a median value (P50) of 76 MPa, P10 of 55 MPa and P90 of 89 MPa."

Jan 1, 2015

By Chris Rule

This paper tells the story of the rapid commercial application of stirred milling technology at Anglo American Platinum?s many Concentrators. The first stirred mill ? a 10 000 litre IsaMillTM; the largest at the time, was commissioned in late 2003. The project development work was presented at SAG 2001. This operation was ?proof of concept? and vindicated the decision to scale up the technology; allowing a rapid and extensive roll-out of mainstream regrind mills as well as several further flotation concentrate regrind mills, over the next six years. Currently 23 stirred mills are in operation with 64 MW of installed drive capacity ? this paper describes the projects? roll-out and the significant results achieved to date. Many operational problems have been solved along the way, some of these will be described. The introduction of the technology has seen a step change in metallurgical results and progressively decreasing operating costs.

Jan 1, 2012

By D. Yuan, L. Yan, R. Kalanchey, M. J. Collins, I. M. Masters

Pressure oxidation tests have been conducted by Sherritt for a refractory gold-silver project located in China. The feed contained 39 g/t Au and 970 g/t Ag; the major gold-bearing minerals were pyrite and arsenopyrite. Since the feed contained a significant amount of silver, which can be refractory to cyanide leaching after pressure oxidation due to the formation of argentojarosite, the test program included investigation of methods to enhance silver recovery. The "lime boil" process proved successful and was incorporated into the flowsheet. Gold extraction from the lime boil product solids was 95 to 98%; silver extraction was up to 94%.

Jan 1, 2011

By William E. Roscoe

"Mineral exploration properties are those on which an economically viable mineral deposit has not yet been discovered. Such properties are bought, sold, optioned and joint ventured on the basis of their perceived potential for the existence and discovery of a viable mineral deposit. The intrinsic value of an exploration property is therefore based on the exploration potential. One measure of the exploration potential is the amount that can be justified to spend on exploration for a viable deposit.The appraised value method uses a cost approach to value exploration properties. It is based on the premise that an exploration property is worth the meaningful past exploration expenditures plus warranted future costs to test remaining exploration potential. Results of past exploration work are analyzed in order to retain only those past expenditures that are productive in terms of identifying remaining potential. Warranted future costs comprise a reasonable exploration budget to test that potential.INTRODUCTIONThe purpose of this paper is to describe a cost approach to the valuation of mineral exploration properties and to provide some valuation examples. The particular cost approach described is the Appraised Value Method, which is best applied to mineral properties at the exploration stage.At present there are no comprehensive regulations or guidelines in Canada which specify what approaches and methods to use for the valuation of mineral properties. In this paper, the Appraised Value Method described is one method that the writer considers to be accepted industry practice for mineral properties at the exploration stage.Mineral properties are valued for a number of reasons, including mergers and acquisitions, non arm's length transactions, pricing of initial public offering of stock, support for property agreements, litigation, expropriation, and insurance claims."

Jan 1, 2003

By I. Vazaios, M. S. Diederichs, N. Vlachopoulos

"As rock engineering moves from continuum to more discontinuum approaches for modeling, the engineer must make decisions regarding the degree of complexity to simulate for a given application, balancing the level of structural detail within the rockmass model with computational cost and result accuracy. It is important to consider that model does not need to include all the existent fractures and that representative geometrical properties for a given rock mass volume can be defined including only major structural entities.Within this paper, the scale-dependency associated with the geometrical properties of fractured rock is investigated utilizing a Synthetic Rockmass (SRM) approach with a view to characterize such ground to aid in the design of geotechnical works. In terms of process, the concept of the Representative Elementary Volume (REV) is used to determine the equivalent structural properties of the rockmass in order to justify the applicability of far-field behaviour of such ground. A large size Discrete Fracture Network (DFN) measuring 60m x 60m x 60m has been generated using the structural data obtained from LiDAR scanning of the Brockville Tunnel, Ontario, Canada. A number of DFN samples of varying sizes are extracted from the master network, generated using MoFrac, in order to be used as a the basis of the structural analysis of the rockmass. Volumetric measurements for the density and the intensity of jointing are employed in order to approximate the geometrical REV for the networks.In this paper a complete methodology of how to generate a DFN from LiDAR data and its analysis in order to determine the size of a geometrical REV is demonstrated. For the specific rockmass found in the area of the Brockville Tunnel, a geometrical REV measuring 3.5m x 3.5m x 7m is established. The results are generally in good agreement with the in-situ observations."

Jan 1, 2015

By R. Khanna, K. Hyun Ko, A. J. Berkovich, J. Hook

"The co-pyrolysis of synthetic polymer polyethylene terephthalate (PET) and agricultural wastes (naturally occurring polymer-macadamia nut shell) was investigated in the temperature range 473K to 1273K using a horizontal furnace with an aim to understand their thermal degradation under isothermal conditions. In-depth characterization of pyrolysis residues was carried out using x-ray diffraction (XRD) and solid state nuclear magnetic resonance (NMR) for carbon structure, and through determination of the concentration of unpaired electrons using electron paramagnetic resonance (EPR). In previous studies, it has been found that PET thermally decomposes ~ 650K-700K, releasing (~80 wt % of initial weight) gaseous products due to random chain scission. In the case of macadamia nut shell, three types of byproduct can be obtained from pyrolysis: char, tar and gaseous products. In the co-pyrolysis of macadamia nut shell with PET in 50-50 wt% ratio, total product weight ratio could be modified with the addition of PET acting as a hydrogen source. This is because a recombination of thermal cracking products of cellulose could be suppressed by hydrogen from PET, which will later lead to an enhancement of tar formation. In addition, pyrolysis around 673K is sufficient for bond cleavage to occur in cellulose and lignin leading to the formation of negatively charged activated carbon with high surface area, providing bonding sites for volatiles evolving from PET. Therefore the co-pyrolysis may be able to enhance the product yield (tar/char/solid carbon residue) along with a reduction in the release of gaseous products. During the co-pyrolysis, temperature was found to have a significant influence on the kinetics of thermal degradation and solid residual by-products after co-pyrolysis.INTRODUCTIONPlastics are being used worldwide in a wide range of applications in the modern society; their usage has resulted in increasingly a massive waste problem. The production of most synthetic plastics requires hydrocarbons that are produced from petrochemicals derived from fossil oil and natural gas, a non-renewable source (Speight 2011). Currently, plastic manufacture utilizes ~4% of world oil and gas production, and it is expected to drive further increases in petroleum demand by 1-2% due to their large volume of manufacture (Hopewell, Dvorak et al. 2009). Landfilling and incineration of plastic waste are the two main routes to plastic waste management (Encinar and González 2008). In Australia, only 10% of waste plastics were recycled in 2006 (White and Hyde 2011). This means that large amount of fossil fuels from plastics has either been simply burned for energy recovery or buried in the ground. There is an urgent need for developing alternative avenues for recycling waste plastics. Our group at UNSW has carried out extensive research on the recycling of waste polymers as carbon resource in steelmaking including slag foaming and carbon dissolution from waste plastics into liquid steel at 1600°C; the effect of basic plastic characteristics such as chemical composition, structure, bonding network etc. was examined (Sahajwalla, Rahman et al. 2009)"

Jan 1, 2012

By A. Warczok

Chalcocite concentrate obtained by magnetic separation and flotation of Bessemer matte is processed in the Inca top blowing bottom stirring MK reactor into semi-blister copper. The semi-blister is then converted into blister copper in the multi-purpose vessels (MPV) by oxidation of iron, nickel and sulphur. High melting point NiO and Fe30 4 are formed inside the MPV s, which together with Cu20 and smaller amount of fayalite are the major constituents of the solid mush. The accumulation of solid mush and buildup requires periodic MPV cleaning by adding reductant and copper-nickel matte, a unique process called "washout". Various reductants and their combinations, such as pig-iron, 15%Si Ferro-silicon and 50%Si Ferro-silicon, have been used for the reduction of solid mush and buildup. The possibilities of using calcium carbide as a reductant and slagging flux were examined experimentally at the crucible scale. The rate of reduction of MPV buildup was determined by continuous measurement of CO and C02 contents in the offgas and the flowrate of argon carrier gas. The rate of the buildup reduction with calcium carbide was approximately five times faster than the rate of reduction with coke. Additionally, the formation of CaO results in the melting of reduced buildup and formation of a slag at 1300°C and higher temperatures. It was found that simultaneous silica addition enhanced the melting and slag formation. The results showed the strong dependence of the reduction rate on temperature. Activation energy is approximately 225 kJ/mol. Expected benefits of using calcium carbide are related to cost saving on reductant, significant acceleration of solid mush reduction, and reduced amount iron input from reductant.

Jan 1, 2007

By D. Yu, T. A. Utigard, M. Barati

"Sulfation roasting of nickel concentrate to generate water-soluble metal sulfates was investigated as an alternative process to smelting for the recovery of valuable metals. The kinetics of dissolution of various species of the calcine in three leachants was studied; hot water, dilute HCl, and concentrated HCl. The results indicated that dissolution of sulfates by hot water at 90 ºC is achieved within 30 minutes. In order to increase the recovery of the valuable metals, acid leaching is necessary due to the existence of ferrite in the calcine.INTRODUCTIONInvestigations on the sulfation roasting of nickeliferous sulfide ores or concentrates were mainly carried out in 1950’s to 1990’s to generate water soluble non-ferrous metal sulfates followed by metal recovery by leaching (Stephens, 1953; Thornhill, 1954, 1961; Fletcher and Shelef, 1964a, 1964b; Fletcher and Hester, 1964; Frankiewicz, 1977; Norrgran, 1983). Commercialization of the sulfation roasting process was only performed by Falconbridge Ltd. (Thornhill, 1961; Boldt, 1967), which employed a sulfation roast process on nickeliferous pyrrhotite at 680 oC where Ni, Cu, and Co were leached and Fe2O3 was produced for the iron industry. In 1965, 118,342 tons of pyrrhotite was processed, however because of the huge SO2 emissions (no acid plant) relative to the nickel production and the poor economics, this plant was shut down.Nickel production from sulfide ores via pyrometallurgical means, especially the electric furnace smelting process, is a major emitter of SO2 to the environment and a big energy consumer (Warner, Diaz, Dalvi, Mackey, Tarasov and Jones, 2007). Nowadays, due to the more stringent environmental regulations as well as the need to reduce energy consumption, metal production by sulfation roasting is gaining more attention as an alternative process to smelting. The main focus of this paper is to investigate the extent and rate of leaching of valuable metals from the sulfation roasted nickel calcine, aiming to maximize the metal recovery and minimize the dissolution of iron species."

Jan 1, 2012

"This paper presents results of ongoing research being carried out at the University of New South Wales into improved methods for estimating rock mass strength. In this paper the rock mass strength of Hawkesbury Sandstone is assessed. An estimate is first made based on an extensive database of intact rock strength data being collated by the author and the assumption that the rock mass strength can be determined following the GSI approach. The resulting strength envelope is then compared with nine documented case studies where stress induced failure has occurred in tunnels excavated within Hawkesbury Sandstone. The case studies cover a range of conditions:• construction dates from 1880s to 2006• spans from 3.2 to 12.5 m• depths from 17 to 124 m• excavation methods of drill & blast, roadheader and TBM.Finite element modelling is used to assess the likely magnitudes of the stresses present at the time of failure. The finite element models are interrogated to provide the values of major and minor principal stresses in and around the mapped failure zone. Failure and stable points are then compared to the rock mass strength envelope(s) of Hawkesbury Sandstone derived using the Hoek-Brown criterion and spalling criteria. The Hoek-Brown rock mass strength envelope differentiates between the ‘failed’ and ‘stable’ zones remarkably well.INTRODUCTIONStress induced failures of rock masses are fortunately rare in civil tunnelling. However, when they occur they provide an opportunity to calibrate an assumed rock mass strength criterion. This paper compares an estimate of rock mass strength for the Hawkesbury Sandstone with the following cases where stress induced failure occurred in tunnels excavated within Hawkesbury Sandstone.• Cataract & Devines Tunnels of the Upper Canal (Upper Nepean Scheme)• Malabar Outfall Tunnel• Sydney liquefied petroleum gas (LPG) Storage Cavern• Northside Storage Tunnel• Cross City Tunnel• Lane Cove TunnelTwo-dimensional finite element modelling is used to assess the likely magnitudes of the stresses present at the time of the failures. The principal stresses are then compared to the assessed rock mass strength envelope(s) of Hawkesbury Sandstone derived using the 2002 Hoek-Brown criterion (Hoek et al., 2002) and the spalling criterion suggested by Diederichs (2007)."

Jan 1, 2015