Search Documents

By A. R. Laplante

Gold recovery early in the flowsheet, typically from the primary grinding circuit, has seen significant advances in the past three years. Some of the advances achieved under the auspices of the AMIRA P420B Gold Processing Technology project are reviewed. The areas covered are gravity-recoverable gold (GRG) characterization, GRG behaviour in classification, gravity recovery simulation and the link between gravity recovery and cyanidation.

Jan 1, 2005

By R. C. Gilmore, J. F. Brune

"Pulverized limestone rock dust used in United States underground coal mines to prevent and suppress coal dust explosions must easily disperse by forces of a methane or coal dust explosion. Moisture in the mine environment causes caking of the dust. Colorado School of Mines researchers performed dispersibility tests in a full-size explosion test drift. Tests included conventional, hydrophobized, and rock dust approved for German mines. Conventional and German standard rock dust products partially agglomerate, which may not be effective in suppressing a coal dust explosion, while hydrophobic rock dust retains better dispersibility.INTRODUCTIONA coal dust explosion devastated the Upper Big Branch mine in 2010 resulting in the death of 29 miners, the worst mining accident in the United States since 1972. The explosion propagated through approximately 65 km of active mine workings, but was extinguished in areas that had been properly rock dusted (Page, 2011). Researchers have long studied and established the ability of inert limestone rock dust to suppress coal dust explosions, see Richmond et al. (1975), Cybulski (1975), and Sapko et al. (2000).To be effective, rock dust must contribute to a total inert content of > 80% by weight and 100% of rock dust particles must pass through an 850 µm sieve, while 70% of the rock dust must be finer than 74 µm. This is established in US regulations 30 CFR §75.2. Dry rock dust is a nuisance that prevents mining work downwind from rock dusting activities. To overcome this problem, dust manufacturers have proposed applying the rock dust as a wet slurry or foam. After drying, manufacturers expected the slurry or foam-applied dust to have the same explosion suppression capabilities as dry-applied rock dust.Researchers at the Colorado School of Mines (CSM) designed and built a full-scale, underground Explosion Test Facility (ETF) at the CSM Edgar Experimental Mine in Idaho Springs, Colorado about 20 miles west of the CSM Golden, Colorado campus. To disperse the different rock dust products, researchers produced an air pressure pulse using a mesh array of PETN detonation cord. This method is simpler, more reproducible and safer than other methods considered, including methane-air explosions and a compressed air cannon. The detonation cord blasts produce a wind velocity of 30 to 50 m/s, the minimum velocity at which coal dust explosions can propagate, based on research by Nagy (1981) and Cybulski (1975)."

Jan 1, 2019

By P. G. Lazenby

This paper describes the latest instrumentation improvements in the INPUT Airborne E.M. System, particularly the new electronic signal-processing techniques. Several anomaly examples illustrating these techniques are shown.

Jan 1, 1973

By C. Guo, R. J. Chalaturnyk, M. MacKinnon, J. D. Scott

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd. oil sands plant. Over the past years (since 1996), there has been a marked change in the densification behaviour of MFT in the MLSB. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings) at the area with intense microbial activity. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. It may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program was carried out to study the mechanism leading to the rapid densification phenomenon. A review and discussion of the research program is given and some results from the field investigations and small-scale column tests are presented in this paper.

Jan 1, 2007

By T. Gerritsen, R. MacRosty, R. Pula

For several years Hatch has been installing fibre optic temperature sensors on the copper cooling elements of smelting furnaces to improve monitoring capabilities in critical locations. The metal/matte tapblock is a key area to monitor in the furnace as it undergoes severe wear from the molten material repeatedly drained through it. The high wear rate around the tapblock means downtime is necessary to perform refractory repairs. A good understanding of the tapblock condition allows the operation to maximize safety and production; consequently the metal/matte tapblocks have been the focus of this study. Fibre optic technology allows the installation of numerous sensors in locations that are very sensitive to refractory thickness, thereby providing information previously unavailable with traditional measurements. The transient nature of the thermal response to tapping and the three-dimensional geometry of the tapblock confound the interpretation of refractory thickness from temperature measurements. This paper focuses on the analysis of both plant data and thermal modelling simulations and details the progress made in relating the temperature measurements to the refractory thickness in front of the copper tapblock.

Jan 1, 2014

By C. W. Davis

AN inclined shaft is usually more difficult to sink than a vertical shaft, yet it is often chosen because of the subsequent saving in cross-cuts required to reach an inclined ore body. This paper briefly discusses the factors which led to the choice of an incline and then describes the operations involved in the preparatory work and in the sinking. These operations included a programme of mining out the underground facilities and installing the structures required for a hoist-room, cable-raise, waste-pass, ore pass, two sets of skip dumps, and a collar station equipped with counterbalanced drop-rails. The shaft was sunk 1,000 feet and four stations were cut, each with loading pockets. As the sinking progressed, the rock changed from hard porphyries and dense cherts to blocky limestones and earthy rubble. These conditions called for a change in methods and it is to the red it of the shaft-sinking crew that they overcame the new difficulties as the shaft progressed, while maintaining a satisfactory monthly advance. The section mined out was nine feet six inches by seventeen feet overall. This gave room for three compartments: two skip compartments four feet three inches by five feet nine inches inside the timber, to handle two-ton skips, and a manway three feet six inches by five feet nine inches. The sinking began on December 16th, 1941, and was completed on February 15th, 1943.

Jan 1, 1945

By T. Takayama Filho

Votorantim Metais Zinco is a smelting facility which produces SHG zinc, zinc alloys, sulfuric acid, liquid SO2, copper sulfate, cadmium metal and silver concentrate. It is located at Juiz de Fora, Minas Gerais State, Brazil. This facility has been operating since 1980 and its current capacity is 95,000 tonnes of zinc per year, using mostly imported sulfide concentrates.The plant uses the conventional roast-leach electrowinning (RLE) process, in which iron is removed from the circuit as jarosite. The residues generated by the RLE process, which amount to about 200 t/day (dry weight), were until 10 years ago, deposited in tailing ponds having no impervious lining. More recently, jarosite and other wastes have been deposited in a properly built reservoir, but this is reaching its maximum capacity. In order to decommission these disposal operations and to reclaim the sites in an environmentally acceptable manner, Votorantim Metais concluded in 2004 a rehabilitation project for the old tailings pond and prepared detailed plans for managing the current and future disposal of jarosite-bearing residues. This paper describes the procedure for removing iron from the hydrometallurgical circuit and discusses the past and current status of the residue disposal sites, as well as the future challenges related to the environmentally acceptable handling of iron residues.

Jan 1, 2006

By Alessandro Navarra, Roberto Parra, Boyd Davis, Frank Mucciardi

A smelter scheduling algorithm has been developed, which allocates the oxygen production between the smelting furnace and the converter aisle, so as to maximize copper throughput. The algorithm is intended for daily operation planning, controlling the sequencing of the converter cycles, and the oxygen drawn by these cycles. In some cases, it may be worthwhile to decrease converter oxygen allocation in favour of the smelting furnaces. Thus, a better utilization of the oxygen plant can increase primary copper throughput by several percentage points. This principle is demonstrated through sample computations. The approach presented in this paper can be incorporated into smelter management software.

Jan 1, 2015

By Y. M. Zhao, C. L. Duan, Z. F. Luo, X. L. Yang

"Fine coal beneficiation in a dry way is considerably imperative for the efficient utilization and conservation of coal resource in drought regions, especially for China. In this study, a continuous vibrated gas-fluidized bed separator was established and developed based on the results of laboratory batch separation results. The fluidization behavior and the effects of several main parameters including superficial air velocity, vibrational parameters, bed height and separating time were systematically investigated. The results showed that the bed expansion increased linearly with the superficial air velocity and theoretically, higher bed expansion benefited the hindered settling process of fine coal particles. However, larger superficial air velocity would induce intense fluctuation in bed surface and a poor performance of density segregation. The conveying velocity of particles was mainly determined by the vibration angle and a predicted model was established by the nonlinear regression analysis. A theoretical model of bed height distribution was established and this model fitted the measured value well. The beneficiation performance of this separator was evaluated by separating -3+1 mm Wuhai fine coal. The results showed that the probable error, E, is 0.225, indicating a continuous vibrated gas-fluidized bed separator could achieve a satisfactory performance.INTRODUCTIONFine coal beneficiation in a dry way is considerably imperative for the efficient utilization and conservation of coal resource in drought regions, especially for China. Meanwhile, it is also conducive to environment protect and low-carbon, green development of coal sector. In recent years, the increasing academic interest in the field of fine coal dry beneficiation has been aroused in most of big coal countries. In summary, recent processes of fine coal dry beneficiation are, according to their processing principles, mainly classified into two categories: dense medium beneficiation (Dong et al., 2015; Fan, Chen, Zhao, & Luo, 2001; Luo et al., 2008; Macpherson, Iveson, & Galvin, 2011) and improved pneumatic beneficiation (Patil & Parekh, 2011; Yang, Zhao, Luo, Song, & Chen, 2013; Yang, Zhao, Luo, Song, Duan, et al., 2013; Zhao, Zhao, Chen, & Luo, 2015). The former deploys artificial dense medium, such as magnetite powder and fine sand, to form a stable gas-solid suspension with certain density under the function of the upward fluidizing air flow and in some case, the external force field like vibration and magnetic field. Generally, it is believed that the process of air dense medium fluidized bed (ADMFB) is suitable for separation of coarse coal (-50+6 mm) and can't obtain a satisfactory result for fine coal separation (Luo, Chen, & Zhao, 2002; Luo et al., 2008). However, some recent laboratory efforts (Patil & Parekh, 2011; Zhang et al., 2014) attempt to find an improved performance for fine coal beneficiation in ADMFB with some modifications. The point of these works is to use a comparatively shallow bed and finer magnetite powder with appropriate size distribution. It is known that fluidization of finer magnetite powder is prone to arouse adverse fluidization properties such as channeling and slugging. Thus, the external force is introduced to an ADMFB in order to improve the fluidization quality of a magnetite powder bed. Some recent literature on air dense medium magnetically stabilized fluidized beds (Fan et al., 2001; Luo, Zhao, Chen, Fan, & Tao, 2002; Song, Zhao, Luo, & Tang, 2012), air dense medium vibrated fluidized beds (Luo et al., 2008) and Reflux Classifier (Macpherson, Iveson, & Galvin, 2010) reports that the separation efficiency, namely the probably error E value, of dense medium separation of fine coal ranges from 0.066 to 0.07, indicating a good separation performance. But, the main unresolved problems of dense medium beneficiation are located in the processes of product purification and medium recovery and are urgent to be solved befor"

Jan 1, 2016

By V. Silins, J. Tameling, R. C. Cook

"A general review of the wear problems encountered in the mining industry is presented and current practice for wear protection systems is reviewed.A new concept in wear protection is described and compared to alternative systems. Utilization of conventional stud welding technology and abrasion-resistant wear studs is shown to be a useful supplement or substitution for conventional techniques. Operating life of many consumable components can be increased by up to four fold. The technique is highly portable for on-site field application or can be used in shop environments.Details of the wear protection model and metallurgical properties of the wear component are also reviewed. Laboratory wear test data are reported to supplement field test performance or to screen potential alloy compositions for application in specific environments.A Review of Wear Problems and Wear ProtectionThe emphasis on wear protection has increased in recent years because of the increasing impact of the potential savings in time, materials and energy. A 1974 German study concluded that attention to tribology, the study of friction and wear, could save approximately $3 billion, and a study in the U.S.A. at the same time put the figure at $100 billion of which $20 billion was for materials. A more recent American study put the energy component of the potential savings at $16.2 billion per year. A recent British study estimated the total potential savings in the U.K. as $1 billion per year, with the largest savings coming from lower maintenance and replacement costs ($500 million), lower breakdown costs ($250 million) and increased machinery life ($200 million). These three major contributions are all potentially accessible in the mining industry."

Jan 1, 1982

By Jean-Louis Robert

Field work inaugurated in 1962 in the townships of Lemieux and Lesseps, in the Gaspe Peninsula of Quebec, has permitted the author to delineate the lithologic units of the area, to elucidate a few stratigraphic problems and to outline several zones of alteration. Certain features of these zones and the numerous mineralized showings in the area merit the attention of prospectors and exploration companies.

Jan 1, 1966

By Jan Kvinge, Aina Opsal Bakke, Yanjun Li, Jan-Ove Løland, Svein Jørgensen

"Compound casting is a very attractive approach to reduce the weight of components for some specific applications while keep both the functional and the mechanical property requirements. In this work, Al-7Si-Mg alloy /copper compound castings were produced through a low pressure die casting process. To reduce the oxide present in the interface, flux coating of the copper pipes was tested. The interface layer formed between the two alloys was investigated using Optical Microscopy (OM), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS). Vickers Micro-hardness was also measured across the interface. Results showed that the flux coating prevented the formation of the metallic bond between copper and aluminum. Instead, high concentrations of potassium, magnesium and fluoride, coinciding with formation of KMgF3 and MgF2, were detected in the interface. In the castings without surface treatment, a continuous metallurgical bond was achieved. In the bond layer, various Al-Cu intermetallic phases have been detected. In addition, formation of primary silicon particles in the reaction layer was observed in all castings. The mechanism for the formation of the intermetallic phases and the strength of the interface layer have been discussed.INTRODUCTION Recent development in the automotive industry has focused on producing lightweight components, which can reduce CO2 emission and increase the efficiency. Often, one material alone is not able to meet the requirements for a specific use. The need for lightweight bimetallic components has therefore increased. Aluminum-copper bimetallic components can be used in wires and bus bars where conductivity is an important factor (Lee, Bang, & Jung, 2005). Compared to Al-Cu alloys, Al-Cu bimetallic components can reduce both weight and cost without reducing electrical and thermal conductivity (Sheng, Yang, Xi, Lai, & Ye, 2011). A challenge is, however, that aluminum and copper have high affinity to each other, especially at elevated temperatures. This causes formation of brittle intermetallic phases with high electric resistance (Liu, Wang, Sui, Wang, & Wenjiang, 2016). In addition, both metals are subjected to oxide formation on the surface. Copper is especially exposed to oxidation at elevated temperatures (Pinnel, Tompkins, & Heath, 1979), while a thermodynamically stable oxide layer will spontaneously form on the aluminum surface (Papis, Loeffler, & Uggowitzer, 2009). Oxides are known to be passive substrates, which will reduce wettability and will thus prevent the formation of metallic bonding between aluminum and copper (Papis, Hallstedt, Löffler, & Uggowitzer, 2008)."

Jan 1, 2018

By F. J. A. van Ruitenbeek, M. Dalm

In the presented study test work was performed with near-infrared hyperspectral imagery (NIR-HI) on 36 ore samples from a South-American epithermal Au-Ag mine. The aim of the test work was to investigate if NIR-HI provides information about the alteration mineralogy of samples that can be used to predict their economic value. Mineral distribution maps were produced from the hyperspectral images by using correlation coefficients between the image pixels and a set of reference spectra. These maps showed that detection of mineralogy with NIR-HI can be used to distinguish; i) ore particles with low Au and Ag grades, ii) ore particles with high carbon contents, iii) ore particles with high sulphur contents.

Jan 1, 2015

By Desmond M. Levins, Reginald K. Ryan

"Removal of radium from uranium tailings would substantially lessen their environmental impact because it would eliminate, or greatly reduce, the hazards arising from radon emanation, leaching of radium, dust dispersal and gamma radiation. A process is described to extract radium from tailings by leaching in 3M Nael solution. The radium can be rapidly leached at ambient temperatures by either multi-stage contact in agitated vessels or washing on a tailings filter cake. Extraction efficiencies ranging from 80 to 94% have been measured for tailings derived from a number of Australian ores.Methods for radium recovery from the leach solution by precipitation, ion exchange and adsorption have been examined. Precipitation as barium/radium sulphate appears to be the most suitable approach. A possible flow diagram for the process is proposed which involves recycle of the saline leach liquor.IntroductionDisposal of mill tailings is the most contentious environmental issue facing the uranium mining industry. The conventional approach to managing tailings is to store them in a dam above ground. Attempts have been made to stabilize some tailings piles by physical or chemical methods. In a few cases, the tailings have been covered with earth and revegetated. However, most tailings piles from abandoned mills are in a neglected state and subject to the erosive and dispersive forces of nature. The cost of remedial action is high. The United States Department of Energy (DOE) has estimated that it will cost up to $130 million to rehabilitate abandoned mill sites in the U.S .A..Environmental authorities are now insisting that uranium mining companies improve their methods of tailings disposal. In the United States, the preferred approach is burial, either in mines or in specially excavated pits. Tailings retention systems as operated in Canada are regarded as storage facilities until an acceptable method of disposal is found. In Australia, the Fox Commission recommended that tailings from the Ranger project should be returned to the open-cut mine. Returning tailings to the mine has considerable merit, but it is not always a viable option. In many underground operations, it is not physically possible to fit all the tailings in the worked-out mine. In other cases, the groundwater hydrology of the mine may be unfavourable."

Jan 1, 1980

By B. Tonn, F. Kröger

"The continued development in engine technology is leading to an augmentation in power density which steadily elevates the requirements for thermally and thermo-mechanically highly loaded components such as cylinder heads and pistons. Due to these high performance requirements conventionally applied Al-Si alloys have reached their application limits, since their mechanical properties deteriorate quickly under the influence of heat. Improved applicability is given by Al-Cu-based casting alloys which have a superior high-temperature strength than Al-Si alloys. Since Al-Cu alloys exhibit insufficient casting characteristics, especially regarding hot tearing susceptibility and increased tendency for porosity, it is currently not possible to cast geometrically complex components in robust permanent mold casting processes. The further development of Al-Cu alloys is aimed at finding an optimum between improved castability while high-temperature strength and thermal conductivity are not deteriorated. It is known that a high amount of eutectic reduces the hot tearing susceptibility of an alloy, but it reduces thermal conductivity at the same time. In this paper it will be presented how the conflicting objectives – improved high-temperature strength, good thermal conductivity and reduced hot tearing susceptibility – can be brought together to develop an optimized Al-Cu alloy for application in permanent mold casting.INTRODUCTION At the beginning of the 21st century car, engine blocks were primarily made of gray cast iron (GJL). Less than half a decade later, the choice of material had shifted towards lightweight materials. Ever since, the car engine manufacturing is dominated by aluminum-based alloys. The weight of car engine blocks could thus be reduced by around 50% due to the lower specific weight of aluminum alloys compared to gray cast iron. Furthermore, the high thermal conductivity of aluminum alloys allowed a reduction of complex cooling channel systems and thereby promoted the advancement of this material group. The further development in engine technology leads to an augmentation in power density which elevates the requirements for thermally and thermo-mechanically highly loaded components. For example, in diesel-powered car engines the upper required limits can reach an ignition pressure as high as 230 bar and gas temperatures of up to 1000°C. Thereby, thermal loads can cause high alternating thermal stresses (Grzincic, 2003) which can effectively be reduced by providing high thermal conductivity."

Jan 1, 2017

By R. B. McIntosh, S Ramanchuk

A brief description is given of the process used by Sherritt Gordon Mines Limited to recover cobalt metal from nickel-cobalt sulphides. A description of the equipment with the operating conditions is presented with an evaluation of the corrosion test results for various stainless steels and other acid resistant materials for the part of the process involving the sulphuric acid leaching of nickel-cobalt sulphide slurry under air pressure. SINCE 1954 the Sherritt Gordon ammonia leach process has been used at Fort Saskatchewan to recover nickel metal, copper sulphides and cobalt-nickel sulphides from nickel concentrate produced at Lynn Lake, Manitoba. 'To develop a process for recovering cobalt and nickel from the cobalt-nickel sulphides, studies were carried out in the Sherritt Gordon laboratory and pilot plant and, late in 1957, continuous acid leaching of sulphides was started in the refinery. In September 1958 the present equipment

Jan 1, 1961

By Dale Scott

"The Aggregate Resources Inventory Program was initiated 10 produce reports which assess the aggregate resources of municipalities designated under the Pits and Quarries Control ACI, 1971.Each report consists of three copies accompanied by a text. The text describes the local mineral aggregate resources, extractive activity and characteristics of the ""Selected Deposits"". The first map shows the known sand and gravel resources and their quality. The second map indicates selected sand and gravel resources of primary, secondary and tertiary significance. The third map indicates both bedrock resources and bedrock areas suitable f or extraction. These maps and the text are prepared in a formal suited for use by planning personnel.Recently, the Aggregate Resources Inventory Program has undergone evolutionary changes. New sources of data are being utilized in the inventory reports; in particular, detailed field assessment by inspecting, sampling, drilling and backhoe pitting. Liaison and joint assessment with district and regional Mineral Resources staff of the Ministry of Natural Resources, and personnel of the Ministry of Transportation and Communications, are key components of the Program.Twenty-two reports were available to the public as of December 1980, with a further thirty-six awaiting publication. Our present production rate is 3.5 reports per month. The reports appear to be well accepted by the municipalities and have proven effective in conserving prime aggregate resource areas.IntroductionThe urbanization of Southern Ontario has resulted in a major increase in the production of industrial minerals, such as sand, gravel, clay, shale, gypsum and stone, for use as cru shed aggregate, building stone, lime and cement.Although mineral aggregate deposits are plentiful in Southern Ontario, they are fixed-location, non-renewable resources. The potential for extractive development is usually greatest in urban fringe areas where land-use competition is extreme. Comprehensive planning and resource management strategies are required to make the best use of available resources, especially in those areas experiencing rapid development. Such strategies must be based on a sound knowledge of the total mineral aggregate resource base at both local and regional levels."

Jan 1, 1982

By Dale Scott

"The Aggregate Resources Inventory Program was initiated 10 produce reports which assess the aggregate resources of municipalities designated under the Pits and Quarries Control ACI, 1971.Each report consists of three copies accompanied by a text. The text describes the local mineral aggregate resources, extractive activity and characteristics of the ""Selected Deposits"". The first map shows the known sand and gravel resources and their quality. The second map indicates selected sand and gravel resources of primary, secondary and tertiary significance. The third map indicates both bedrock resources and bedrock areas suitable f or extraction. These maps and the text are prepared in a formal suited for use by planning personnel.Recently, the Aggregate Resources Inventory Program has undergone evolutionary changes. New sources of data are being utilized in the inventory reports; in particular, detailed field assessment by inspecting, sampling, drilling and backhoe pitting. Liaison and joint assessment with district and regional Mineral Resources staff of the Ministry of Natural Resources, and personnel of the Ministry of Transportation and Communications, are key components of the Program.Twenty-two reports were available to the public as of December 1980, with a further thirty-six awaiting publication. Our present production rate is 3.5 reports per month. The reports appear to be well accepted by the municipalities and have proven effective in conserving prime aggregate resource areas.IntroductionThe urbanization of Southern Ontario has resulted in a major increase in the production of industrial minerals, such as sand, gravel, clay, shale, gypsum and stone, for use as cru shed aggregate, building stone, lime and cement.Although mineral aggregate deposits are plentiful in Southern Ontario, they are fixed-location, non-renewable resources. The potential for extractive development is usually greatest in urban fringe areas where land-use competition is extreme. Comprehensive planning and resource management strategies are required to make the best use of available resources, especially in those areas experiencing rapid development. Such strategies must be based on a sound knowledge of the total mineral aggregate resource base at both local and regional levels."

Jan 1, 1982

By V. Schwinn, P. Fluess, N. Cauderlier, J. Bauer

From a strategic and economic point of view, the development of fine grain high strength steels for long distance pipelines is intensified world wide to satisfy the demand for natural gas in the future.The project related property profiles based on strength, toughness, crack arrest and sometimes resistance against HIC at defined design temperatures require an effective structural refinement using advanced steelmaking and processing in the rolling mill. The microstructure of modern line pipe steels ranges from ferritic pearlitic to ferritic-bainitic and structures where bainite is the dominant component, possibly upgraded by secondary phases. This paper illustrates microstructures and properties of recent orders on line pipe steels both for onshore and offshore application using different processing routes in the plate mill. Examples will be given for SAWL 485 offshore grades, X65 HIC and X70 HIC onshore grades, respectively. Finally, production results of a recent X80 order will be presented.

Jan 1, 2005

By A. Shakoor, T. P. Gautam

The long-term slaking behavior of clay-bearing rocks in the field can be quite different than the short-term slaking behavior in the laboratory. To assess this difference, 12 replicate samples of each of 20 clay-bearing rocks, including 5 claystones, 5 mudstones, 5 siltstones, and 5 shales, were exposed to natural climatic conditions for 12 months. After each month of exposure, one replicate sample of each rock was removed from natural exposure and its grain size distribution was determined. Disintegration ratio (DR), defined as the ratio of the area under the grain size distribution curve of the slaked material for a given rock to the total area encompassing all grain size distribution curves of the tested samples, was used to quantify the amount of disintegration under natural climatic conditions. DR values of naturally exposed samples were then compared with the corresponding values of second-cycle slake durability index (Id2) determined in the laboratory. The relationship between Id2 and DR after, 1 month of exposure, exhibits an R2 value of 0.65 but the relationship deteriorates when DR values for 6 and 12 months of exposure are used, with R2 values of 0.63 and 0.25, respectively. However, when DR values for laboratory samples, computed from grain size distributions of slaked material after second cycle, are compared with DR values of naturally exposed samples for the three periods of exposure, the relationship improves with the corresponding R2 values being 0.61, 0.71, and 0.41. These results suggest that DR may be a better parameter for assessing the long-term disintegration behavior of clay-bearing rocks than Id2.

Jan 1, 2015