Search Documents

By L. C. Uren

THE resistance to flow of mixtures of gas and oil in passing up through the flow tubing of oil wells operated by gas-lift or by natural flow is a factor in oil-recovery technic that has received but little attention. Yet accurate design of a tubing installation for a particular set of conditions, where operation is by either of 'these methods, is impossible without quantitative data on the pressure loss suffered by the oil-gas mixture in its passage through the well tubing to the surface. Because of lack of such information, petroleum production technologists have been compelled to approach this problem by "cut-and-try" methods, which, doubtless in many cases, has resulted in the installation and use of tubing too large or too small for most efficient utilization of the expansive force of the gas used in lifting the oil. Impressed with the necessity for information of this character, the authors have conducted a series of tests with large-scale apparatus in the petroleum engineering laboratories of the University of California, designed to be productive of data that would afford a means of attacking the problem of flow-tubing design on a more scientific basis.

Jan 1, 1929

By John Pew

PRIOR to the development of the bulk-oil carrier, practically all transportation of oil was in barrels and in cans contained in wooden cases; the latter was known as case oil. In the year 1885, approximately two hundred million gallons of petroleum were exported from this country in barrels and about one and three-quarter millions in bulk; less than twelve years later, the shipment in barrels had decreased to nearly one and three-quarter million gallons, while the transport of bulk oil had increased to four hundred eighty-four million gallons. The first modern tanker, the "Glückauf," was built in England in 1886. Her hull, which was 300 ft. long, was divided into compartments by transverse bulk-heads, these compartments being divided by longitu-dinal center-line bulkheads extending throughout the oil spaces. There was a pump room forward of the boiler room, thus providing a cofferdam or safety space. Between the main and upper decks, a narrow trunk extended the full length of the' oil spaces, the trans-verse and longitudinal bulkheads being carried to the upper deck. This allowed for the expansion of the oil from a rise in temperature, and if the tank below the main deck was kept full, the danger of the oil moving with the roll and pitch of the vessel was considerably reduced. Spaces for the carriage of light oil were provided on each side of the vessel outboard of the expansion trunk, while water ballast was carried under the machinery compartments fore and aft. Although vessels previously had been built to carry oil next to the skin of the ship, it is claimed that the "Glückauf" was the first one constructed on the new principle outlined.

Jan 12, 1922

By C. Schlumberger

LAST year the authors presented a paper that discussed the various electrical measurements they perform in drill holes, which they name "electrical coring."' The object of the present paper is to give a brief account of the points of scientific interest that have been elucidated by further field work and laboratory research, as well as the economic results that have been attained recently. The practical examples given in this paper are drawn, for the most part, from the field work performed in Russian oil fields during the years 1931 and 1932. This is due to the fact that, thanks to the comprehensive cooperation of the Russian geologists and scientists, the authors are allowed to make public a large amount of recent information. In other countries in which the authors are engaged in similar work, the competi-tion between private companies makes it imperative, for a considerable lapse of time, to avoid publication of the results obtained. The following points will be discussed successively, under sepa-rate headings: 1. Electrochemical phenomena in drill holes. 2. Stratigraphic correlations and tectonic studies. 3. Relations between the productivity of oil horizons and their electrical resistivity. 4. Location of coal seams. 5. Summary and conclusions.

Jan 1, 1933

By Charles R. Keyes

During the past decade the genesis of the lead- and zincdeposits of the Mississippi valley has received special attention from many distinguished observers. But their united egorts, instead of settling all disputed questions, have, in many respects, involl-ed the general problem in greater uncertainty than would be thought possible under the circumstances. In place of the harmony of opinion that might be expected, there is unexpected disagreement, largely due to the fact that, instead of giving attention to a possible multiplicity of ore-producing conditions among the different deposits, the attempt has been made to bring all deposits under a single genetic head. To a new observer of the lead- and zinc-deposits of the Mississippi valley, it appears at the outset that all the deposits cannot possibly have had the same genesis. In fact, different modes of origin have been often asserted for the ore-bodies, but the difficulty has been that each writer has referred them either all to one category or all to another, and no intermediate ground has been considered possible. Such a position now appears to be clearly untenable. The opinion that, in the deposits of the region under consideration, the ore-materials represent original depositions, made at the time the rocks themselves were formed, is no longer held by any authority, and therefore need not be considered here. Of late years, a number of writers have attempted to account for the presence of the lead- and zinc-ores on the hypothesis that the metallic materials arose in heated solutions from the

Jan 1, 1902

By F. P. Haver, M. M. Wong

The Federal Bureau of Mines has developed a leach= electrolysis method for recovering lead from galena (PbS). Flotation concentrate is leached with ferric chloride (FeCl3) solution to obtain lead chloride (PbC12) and elemental sulfur, PbS + 2FeC13 -+ PbC12 + 2FeC12 + Sº. Over 99% of the P~S in the condentrate is converted to PbC12. The leach solution, composed of brine (NaC1) and FeC13, dissolves the PbC12 as it is formed, leaving a residue of elemental sulfur plus gangue. Very pure PbC12 (>99.9%).is crystallized from the leach filtrate on cool- ing and is subsequently electrolyzed in a fused-salt bath to obtain molten lead metal (>99.9% Pb). Spent leach solution (FeC12) is regenerated for further use by reaction with the chlorine obtained in the electrolysis of lead chloride, and other values, such as Ag, Cu, Zn, and Sº, are recovered by additional treatments of the leach solution and leach residue. This paper discusses results and conditions of the leaching and electrolysis operations.

Jan 1, 1976

By John S. Brown

IN 1925 the writer undertook a detailed statistical study of all producing areas in the Joplin district as a basis for evaluating programs and measuring objectives. For this purpose, the published figures in the yearly volumes of Mineral Resources were used, supplemented for earlier years by publications of the Missouri Geological Survey and other local and less official sources. When all else failed, the available data were projected backward to hazard a reasonable guess as to the unrecorded early output of important areas. Fortunately, the proportion of such prehistory production is not a large factor in any of the totals. These results were used during the next few years to measure the relative importance of various producing areas and to predict the peak period of development of the all-important Picher field. For the purpose of this review, the charts have been completed to the end of 1950. During World War 11, the U. S. Bureau of Mines became interested in a similar study and issued comprehensive statistical tabulations of data up to 1945 ( Info. Circular 7383), which have been checked against the figures used herein. This tabulation, however, does not include all the earlier data used by the writer nor does it offer any estimates of the wholly unrecorded era in the beginnings of the earlier camps.

Jan 9, 1951

By Louis A. Mattson, Winthrop A. Rowe, John T. Cumberlidge, Victor M. Mejia

The parent ultramafic of Nickel Mountain is an alpine-peri-dotite. Compositional layering and late stage dunites suggest the intrusive crystallized in the upper mantle or lower crust. The ultramafic mass was fault emplaced in the upper crust, probably during upper Jurassic time. Soil, saprolite and silica boxwork nickeliferous ores were formed over the Nickel Mountain peridotite during the development and later destruction of the Klamath peneplane. A complex fault pattern was produced by irregular gravity displacements along fault surfaces during the relative uplift of Nickel Mountain. The majority of the ores occur in the fractured hanging wall of these gravity faults. Consequently, structure mapping is important for mining purposes. Ore types at Riddle are classified on the basis of MgO, Fe, and Si02 contents as well as textures. The chemical, mineralogical and textural differences of the various ore types reflect differences in weathering histories. Satellitic ore bodies occur peripherally to Nickel Mountain. These are erosional remnants of landslides and large gravity fault blocks from Nickel Mountain.

Jan 1, 1976

By John Gross

A SURVEY of the status of ore dressing in 19231 placed particular stress on the need of research in the crushing and grinding of ore, especially on the need for a method of measuring the surface of the products obtained in crushing and grinding, and for fundamental data on the law of crushing, in order that intelligent conclusions may be drawn from actual crushing or grinding experiments. There has been no satisfactory means of determining the surface of crushed products. The results have been judged entirely by the amount of the various sizes produced, based on sieve sizing for particles above 74 microns in size and on microscopic measurement or elutriation for particles below 74 microns, a method which could give only a general idea of what had been accomplished. The fact that the long controversy between the followers of Kick and of Rittinger has resulted in no accepted conclusion is evidence of the need for fundamental data on the crushing law.

Jan 1, 1928

By B. G. Bunting, J. H. Johnson, H. J. Schock

This paper describes an experimental method for monitoring diesel-generated exhaust gas pollutants in a deadended drift to assess the effect of control approaches. Experiments were conducted to determine the relative merits of these ventilation configurations: no auxiliary ventilation, induction ventilation at the entrance to the drift, and ventilation of the dead-ended drift with positive displacement tubing. The drift used in this experimental work was approximately 32 m long and slightly downsloping, with an everage height and width of 2.4 and 8.6 m, respectively. For this drift, it was found that ventilation with positive displacement tubing provided the best removal of diesel-generate pollutants. Induction ventilation appeared to be the least effective of the three methods examined.

Jan 1, 1982

By W. J. Leas, L. A. Rapoport

As a preliminary, consicleration is given to the conventional definition of relative permeability and to the conditions governing the simultaneous flow of oil and gas through porous media. For the conditions of flow prevailing throughout most of a gas drive reservoir, the oil and gas can reasonably be supposed to be in capillary equilibrium with each other. Under these conditions, and these conditions only, the relative permeability to liquid can be expressed as a function of saturation. The relative permeability to liquid in that case is dependent upon the distribution of fluids which itself is shown to be related to the capillary pressure, and, in turn, to the saturation. As a consequence, relative permeability to liquid can be expressed in terms of the volume and surface area of a network of liquid channels bounded by the rock and the gas phase. While the volume of this network can be evaluated accurately, the surface area cannot. However, for any such volume, maximum and minimum values of the corresponding surface area can be calculated from capillary pressure data. It is then possible to establish for any saturation the limits within which the value of the relative permeability to liquid must lie. As a consequence of the theoretical development, the validity of an experimental method for measuring relative permeability to liquid which utilizes a stationary gas phase is demonstrated. In this method capillary barriers are cemented to the ends of the core sample to permit the maintenance of capillary equilibrium between the two phases. At the same time, this procedure eliminates undesirable secondary phenomena such as end effects, fissure effects, etc., the presence of which adversely affect the results of other laboratory methods. The results obtained by theoretical calculations, and experimentally, are discussed. In view of the overall precision that can presently be obtained in reservoir calculations, the agreement between the calculated and measured relative permeability to liquid data can be considered satisfactory. In conclusion, for reasons of economy and simplicity, the procedure of calculating limiting relative permeability to liquid curves from capillary pressure data is indicated for general engineering purposes. It is shown that the above procedure can easily be extended to the cases where connate water is present. Its use for reservoir studies is particularly recommended in conjunction with the method for measuring relative permeability to gas' which simultaneously yields the capillary pressure data necessary for the calculations. THEORETICAL Definition of Relative Permeabilities — Basic Equations for Heterogeneous Flow The equations by which the relative permeability concept is defined and upon which the formulation of all of the gas-oil flow problems rests at the present time are expressed as: V, = — Grad PL = — Grad PL ....(la) PL µL, k k KG VG = —K - Grad PG k- Grad Pc .... (lb) Mo where ,. and G refer to liquid and gas; V is the volumetric rate of flow per unit gross area. µ the viscosity, Grad P the potential gradient. and k the specific permeability of the porous medium.* (For horizontal flow, Grad P becomes the pressure gradient; otherwise, gravity must be included.) According to these expressions, each of the constituent phases is considered similar to a homogeneous system where the volumetric rate of flow is proportional to the pressure gradient, and for each of which the constants of proportionality, k, and kG, are termed effective permeabilities. by analogy to the specific permeability as defined by Darcy's law in its original form. In order to obtain a convenient basis of comparison, the effective permeabilities are referred to the specific permeability, k, of the considered porous medium, with the help of the relations: k1. = KI. k kQ = Kn k..........(2) K,. and Kr. are defined as the relative permeabilities to the liquid and to the gas phase respectively, and frequently expressed in per cent of specific permeability. It may be seen that Equations (1); which appear to be a direct generalization of Darcy's law, correspond to the assignment at any given time of a set of "local" permeabilities to each point of the porous medium, and represent in a differential form the two fluid flow system as a simple superposition of the individual single flow systems. The above interpretation implies that the effective or relative permeabilities are independent of pressure or rate of flow,

Jan 1, 1951

By R. W. Parsons, P. R. Chaney

Oil recovery by the imbibition mechanism can be important in fractured carbonate reservoirs with a bottom water drive. Laboratory experiments were performed on water-wet carbonate rocks to model this process. The results are interpreted in light of the applicable scaling laws. The imbibition production behavior of a pillar of rock subjected to a slowly rising water table can be synthesized from data on total immersion experiments on small rock samples. If the rate of water table rise is slow enough and if the physical properties are such that the imbibition zone is of a small vertical extent, then only the final oil recovery on the small samples need be known. Applying laboratory imbibition data to a real reservoir should be done with caution because of possible wettability problems and the unknown behavior of two-phase flow in fractures. INTRODUCTION The spontaneous taking up of a preferential wetting fluid into a porous medium with the simultaneous expulsion of the contained fluid is termed imbibition. One of the many physical imbibition processes is the production of oil by the taking up of water into a water-wet reservoir rock. In certain types of heterogeneous reservoirs, e.g., fractured, it is realized that imbibition alone may be the dominant mechanism. Theoretical studies of imbibition oil recovery have followed several lines of attack. The behavior of certain mathematically tractable and conceptually simple models have been analyzed. Birks1 considered a bundle of vertical capillaries model, while Perotti et al.2 and Kelemen3 used a model of a series of vertically oriented fractures. If the oil production behavior from a block of reservoir rock is known, then the cumulative behavior of a vertical stack of these blocks subjected to a rising water table can be determined by a method outlined by Aronofsky et al. 4 Knowing the capillary pressure and relative permeability functions should uniquely set the imbibition behavior for a given sample. Solutions of the partial differential equations describing the process, however, present some formidable problems. Digital computer techniques have been applied to displacement processes in which the capillary pressure has been included.5"8 More recently, similar techniques have been used by Blair 9 to calculate countercurrent imbibition behavior. The fact that imbibition behavior is described by the usual fluid flow equations (Darcy's Law and continuity equation) implies that the derived scaling laws should apply equally to this situation. Use of model experiments to study imbibition has been employed by Graham and Richardson 10 and Mattax and Kyte,11 who actually tested the scaling law applicability. This study is concerned with scaled model imbibition experiments on water-wet carbonate rocks. Of particular interest is the slowly rising water table experiment. This simulates a highly fractured reservoir with the water table rising uniformly through the vertical fracture system. Experiments were performed on different sized samples and with different rates of rise of the water-oil interface surrounding the rock pillar. Total immersion imbibition experiments on smaller rock samples were performed to test the basic linear scaling laws and to see if these simpler tests could be used to synthesize the rising water table experimental results. THEORY IMBIBITION SCALING LAWS Scaling laws for the flow of two incompressible immiscible fluids in a porous medium have been presented by Rapoport.12 These are derived directly from Darcy's Law for the individual phases and the continuity equation. Results from a laboratory model experiment will duplicate those from some reservoir prototype if a constant proportion is maintained among the three forces acting on the fluids — the capillary pressure gradient, the gravitational gradient and the flowing pressure gradient. Operation of the model (i.e., fluid injection or withdrawal) must be conducted in accordance with specific equations. If the

Jan 1, 1967

By P. A. Fisher, J. B. Wilson, D. J. Whitehead, C. J. P. Ball, A. C. Jessup

The properties of a new magnesium alloy ZT1 containing 3.0 pct Th, 2.5 pct Zn, 0.7 pct Zr are described. The alloy possesses good creep and fatigue resistance up to 650°F, is free from microporosity, and is readily sand-cast. ZT1 is shown to be superior to zinc-free Mg-Th-Zr alloys. THE advent of the jet engine created a demand for a light sand-casting alloy capable of being cast into large complex shapes and capable of resisting creep at temperatures up to 500°F. This demand has been largely met by alloys of the magnesium-cerium mischmetal-zirconium types, containing about 3 pct Ce mischmetal and 0.7 pct Zr, typified by Elektron magnesium alloys MCZ and ZREI, the latter alloy also having a zinc addition of 2.5 pct. These alloys utilize the valuable properties at elevated temperatures conferred by the addition of rare earth metals to magnesium, a fact which has been known for many years and discussed by several investigators.1-1 Murphy and Payne8 showed that the addition of the powerful grain-refining element zirconium to Mg-Ce mischmetal alloys produced alloys with attractive room temperature properties combined with good creep properties and castability. With the increasing power of modern jet engines the temperatures to which some of the magnesium parts are subject are likely to exceed the safe working range of the cerium-mischmetal-containing alloys, and at the beginning of the research considerable interest had been shown by aeroplane engine designers in a magnesium sand-casting alloy suitable for service at higher temperatures, e.g., 600°F and above. At an early stage in the development of this type of alloy a check on the fatigue properties at elevated temperatures indicated that, since the fatigue limit even at 108 eversals was appreciably higher than any permissible creep stress, the main emphasis of the research could be concentrated on creep behavior. The primary aim in developing the new alloy has therefore been to attain maximum creep resistance; but due consideration has also been given to other important properties such as castability, tensile strength, and cost. It is by now well established that it is not possible to correlate creep strength with other short time mechanical properties such as are obtained in tensile

Jan 1, 1954

By L. A. Rapoport, W. J. Leas

As a preliminary, consicleration is given to the conventional definition of relative permeability and to the conditions governing the simultaneous flow of oil and gas through porous media. For the conditions of flow prevailing throughout most of a gas drive reservoir, the oil and gas can reasonably be supposed to be in capillary equilibrium with each other. Under these conditions, and these conditions only, the relative permeability to liquid can be expressed as a function of saturation. The relative permeability to liquid in that case is dependent upon the distribution of fluids which itself is shown to be related to the capillary pressure, and, in turn, to the saturation. As a consequence, relative permeability to liquid can be expressed in terms of the volume and surface area of a network of liquid channels bounded by the rock and the gas phase. While the volume of this network can be evaluated accurately, the surface area cannot. However, for any such volume, maximum and minimum values of the corresponding surface area can be calculated from capillary pressure data. It is then possible to establish for any saturation the limits within which the value of the relative permeability to liquid must lie. As a consequence of the theoretical development, the validity of an experimental method for measuring relative permeability to liquid which utilizes a stationary gas phase is demonstrated. In this method capillary barriers are cemented to the ends of the core sample to permit the maintenance of capillary equilibrium between the two phases. At the same time, this procedure eliminates undesirable secondary phenomena such as end effects, fissure effects, etc., the presence of which adversely affect the results of other laboratory methods. The results obtained by theoretical calculations, and experimentally, are discussed. In view of the overall precision that can presently be obtained in reservoir calculations, the agreement between the calculated and measured relative permeability to liquid data can be considered satisfactory. In conclusion, for reasons of economy and simplicity, the procedure of calculating limiting relative permeability to liquid curves from capillary pressure data is indicated for general engineering purposes. It is shown that the above procedure can easily be extended to the cases where connate water is present. Its use for reservoir studies is particularly recommended in conjunction with the method for measuring relative permeability to gas' which simultaneously yields the capillary pressure data necessary for the calculations. THEORETICAL Definition of Relative Permeabilities — Basic Equations for Heterogeneous Flow The equations by which the relative permeability concept is defined and upon which the formulation of all of the gas-oil flow problems rests at the present time are expressed as: V, = — Grad PL = — Grad PL ....(la) PL µL, k k KG VG = —K - Grad PG k- Grad Pc .... (lb) Mo where ,. and G refer to liquid and gas; V is the volumetric rate of flow per unit gross area. µ the viscosity, Grad P the potential gradient. and k the specific permeability of the porous medium.* (For horizontal flow, Grad P becomes the pressure gradient; otherwise, gravity must be included.) According to these expressions, each of the constituent phases is considered similar to a homogeneous system where the volumetric rate of flow is proportional to the pressure gradient, and for each of which the constants of proportionality, k, and kG, are termed effective permeabilities. by analogy to the specific permeability as defined by Darcy's law in its original form. In order to obtain a convenient basis of comparison, the effective permeabilities are referred to the specific permeability, k, of the considered porous medium, with the help of the relations: k1. = KI. k kQ = Kn k..........(2) K,. and Kr. are defined as the relative permeabilities to the liquid and to the gas phase respectively, and frequently expressed in per cent of specific permeability. It may be seen that Equations (1); which appear to be a direct generalization of Darcy's law, correspond to the assignment at any given time of a set of "local" permeabilities to each point of the porous medium, and represent in a differential form the two fluid flow system as a simple superposition of the individual single flow systems. The above interpretation implies that the effective or relative permeabilities are independent of pressure or rate of flow,

Jan 1, 1951

By C. B. Post, G. V. Luerssen

It is generally recognized that non-metallic inclusions in steel come from two principal sources. First are the chemical reactions in the furnace, or in subsequent deoxidation, resulting in slag which does not free itself from the metal. Much information has been published concerning these chemical reactions and their control through proper attention to slag viscosity, composition of deoxidizers, and other qualities. The studies of this subject by C. H. Herty, Jr. and others through the medium of physical chemistry have yielded much information for the steelmaker. The second source is erosion of ladle refractories, such as lining brick, stoppers, nozzles and runners, causing entrapped particles of globules of fluxed silicate material. In contrast with the large amount of information available on the first source, relatively little has been published on the subject of erosion which, in the case of basic electric melted steel, is the principal source of nonmetallics. This is probably due to the fact that the problem was assumed to be one of simple mechanical erosion, which could be solved primarily by modification of ladle practices. Good improvements have been made by elimination of slurries in the ladle, better ladle and runner refractories, and more attention to pouring temperatures. It is doubtful, however, that this problem has been recognized in its true light since it is not one of simple mechanical erosion but rather one of chemical reaction between the metal and the refractories; and in this sense is as much a problem of physical chemistry as the reactions involved in the actual steelmaking process. The influence of ladle refractories on the resulting cleanness of steels was early recognized by A. McCancel who examined large inclusions in steels made by both acid and basic practices. His chemical analyses showed the large influence exerted by the manganese content of the steel on erosion of the ladle and nozzles used in those days. The presence of MnO in such inclusions led McCance to the hypothesis that both basic and acid steels react chemically with the ladle refractories so that small globules of fluxed refractories are carried in the stream into the molds. This early work of McCance was checked by one of the present authors on basic electric bearing-steel, and it was found that on steels containing as low as 0.40 pct manganese the fluxed surface of the ladle lining after delivering such a heat showed as high as 25 pct MnO by actual analysis. Furthermore, by lowering the manganese content of the steel to 0.20 pct, ladle erosion was decreased with a corresponding decrease in silicate inclusions in the steel. Limitations placed on the manganese content for the required inherent properties made it impossible to pursue this line further, and subsequent attention was concentrated on improved ladle refractories, care in keeping the ladle clean and free from loose refractories up to the time of tapping, and pouring the steel at optimum temperature. Our study of the chemical reactions at the metal-brick interface between steel and ladle refractories was revived in 1939 as a result of an experimental observation made on the cleanness of alloy steels of the SAE types. This observation showed that the relative cleanness of such steels made in basic electric arc furnaces of 12 ton capacity and poured in ingots ranging from 1100 to 2200 lb weight was determined to a large extent by the ratio of the manganese and silicon contents, provided other steelmaking variables such as tapping temperature, pouring temperature, pouring time, amount of aluminum added for grain size control, and degree of deoxidation in the furnace were kept reasonably constant. Detailed studies made on the deoxidation and slag practice during the refining period of basic electric furnace practice showed that these two variables exerted some influence on the resulting cleanness of steel in the form of bars and forgings. The important variable, the manganese-silicon balance, was not apparent until heats were made in succession by the best furnace practice kept under fairly rigid metallurgical control. Another observation pertinent to this work concerned the similarity in the microscope of slag particles causing magnaflux or step-down indications in subsequent rolled bars, and the patches of slag frequently seen on the surface of ingots. These patches are generally believed to come from the glassy metal-brick interface in the ladle and represent an entrapment of such glass (both from the ladle brick and nozzle) in the metal as it flows over the refractories in the neighborhood of the nozzle. These glassy particles are carried down into the mold with the liquid steel, and gradually coalesce into a slag "button" which floats on the surface of the steel as it rises in the molds. Periodically the button is washed to the side of the ingot where it is trapped between the surface of the ingot and the mold, later appearing as a slag patch on the surface of the ingot after stripping. Even though most of the small glassy particles coalesce into a slag button while the ingot is being poured, it is logical to suspect this step in the steelmaking process as being a source of slag lines large enough to cause trouble

Jan 1, 1950

H. M. BOYLSTON, Cambridge, Mass.-I would first like to ask what machine Capt. Bellis used to make his tests on impact strength. I have made some tests with the Charpy impact machine, the specimen being supported at both ends and nicked in the middle, and, find that the results do not always agree with those obtained by the Izod and other machines. I would also like to ask what effect the composition and heat treatment of the tool steel had on the drilling of his rifle barrels, as compared, with the heat treatment of the steel itself? I notice that the analysis of the composition of steel used shows sulphur 0.050 and phosphorus 0.065; I should like to ask how those high limits of sulphur and phosphorus came to be allowed? I have some data which lead me to feel pretty certain that those high limits make for very unsafe steel in rifle barrels. It has never been explained to the satisfaction of all of us, why the manganese is so high: 1.22 per cent. I believe several reasons have been stated; among them, that it is high in order to compensate for the high sulphur, and also to increase the elastic limit and improve other physical properties of steel. Lastly, I wish to ask whether Capt. Bellis has tried any different methods of heat-treating his steel rifle barrels? Apparently these were all heat-treated before machining; has he had any experience with heat-treatment after machining, especially after drilling? Those questions may seem somewhat outside of the range of this -paper, but they are important, and if Captain Bellis can give us any information, it will be very helpful. Dr. J. A. MATHEWS,* Syracuse, N. Y.-The same subject was discussed here last year, and the earlier papers by Dr. Carle Hayward seem to indicate that nothing was gained by the length of time of 'tempering. (It should be borne in mind that his results were based upon electrical and magnetic measurements and not upon tensile tests.) That idea has been accepted as gospel by steel workers, until late years, and particu-larly in connection with alloy steels, on which there is no question that the effect of time of tempering is very marked.

Jan 4, 1918

By John G. H. Crump, E. W. Owen, Peter P. Gregory

.Although oil Production in West Texas in 1939 reached the highest figure for any year since the inauguration of proration, drilling activity continued in the decline that had commerlced the previous year. Production totaled 79,469,341s bbl. of oil during 1939 as compared with 71,257,541s bbl. in 1938 and 75,743,000 in 1937. The number of wells completed in 1939 was 1850, compared with 2045 in 1938 and 2806 ill 1937. Several factors combined to cause the decrease in drilling activity, principally the contiriued increase in the length of time required to obtain a return of invcstment and the scarcity of important new discoveries during the past two years. Of the 1850 completions 1638 resulted in oil wells, 4 were gas wells, 168 were dry holes and 40 were abandoned locations; 1990 new locations were made during the year. The ratio of dry holes to producing wells completed was one dry hole to each 9.75 oil wells, compared with one dry hole to each 7.48 oil wells completed during 1938. This large decrease in dry holes was due to a marked decline in the number of wildcat wells drilled, there having been only 120 wildcat completions during 1939. In addition to the lessened exploration work, the deeline' in activity was largely accounted for by the slowing up of operations in the older pools of Ector, Howard and Winkler Counties. Ector County, which had led West Tcxas in 1938 with 622 new oil wells, furnished only 485 producers in 1939, but was still the leader for the West Texas district. The largest gain in activity was in Yoakum County, whew 350 oil wells were completed in the Denver-Wasson field against 152 during 1938. Most of the older oil fields have been almost completely drilled up, only a few new producers still being completed from time to time in

Jan 1, 1940

By John Mathews

SOMEONE has divided mankind into two groups: (1) those who have the willingness and imagination to weigh the future gain over against a present indulgence, and (2) those who cannot do so. The former have self-control, patience, foresight and a capacity for sustained effort. Those having these homely virtues become the, possessors of capital and hence employers of others. Those lacking these qualities and owning no capital must seek it from those of the first class, and therefore are employed by others. The human qualities, which divide men into two classes-employers and employed-are, however, capable of change by education, training, environment and by all agencies which tend to develop character. These words of the economist have stuck in my mind for many years and the more I see of men in my business contacts the more firmly I am convinced of their truth. The earth in some respects resembles its inhabitants. When we stroll over the fields and hills we are impressed by the unorganized masses of sand and rock which make up the ground beneath our feet. When by chance we come upon a bit of mineral matter in crystalline form we are impressed by its beauty and symmetry and probably have it polished and call it a gem. Gems constitute a minute portion of the earth's crust, and those intellectual gems, worthy of polish, who brilliantly reflect the incident rays of education and experience that have fallen upon them are few among the masses of mankind.

Jan 1, 1931

By E. J. Westerman

Prealloyed powders of nickel-base superalloys were sintered to almost theoretical density in short sinterilzg times. It was ascertained that the rapid densification was caused by a small amount of liquid phase at the grain boundaries, which apparently ovriginated by incipient melting at temperatures considerably below those at which macroscopic melting of the compacts occurred. An increase in the quantity of liquid phase present during sintering-, caused by an increase in the sintering temperature, increased the densification rate, but resulted in a decrease in the room temperature tensile propevties. NICKEL-base superalloys, which presently comprise an important group of high temperature alloys, are difficult to fabricate by the forging, casting, and machining operations presently used. As it was felt that fabrication by powder metallurgical techniques might offer advantages in the production of super-alloy parts, a basic investigation of the most important process in the sequence of powder metallurgical operations, the sintering process, was undertaken on Rene 41, Udirnet 500, and Nimonic 90 and 100 powders. These alloys age harden by the precipitation of the ? Ni, rA1,Ti) phase. Nickel-base superalloys of the Nimonic type have been fabricated by powder metallurgical methods, and their mechanical properties reported in detail.' Other alloys for high temperature service which have been fabricated by powder metallurgical methods include a Co-base alloy of the Vitallium type;2,3 alloys with a Co-Ni-Fe-Cr base;4 stainless steels;5'6 Cr-W-Co alloys;" and a Co-base alloy, X-40.8 METAL POWDERS The superalloy powders investigated were: a) a prealloyed at.omized Rene 41 powder; b) a prealloyed atomized Udirnet 500 powder; c) a prealloyed atom-

Jan 1, 1962

By R. B. Schluter, M. M. Fine

Development of a process for winning copper from pelletized chalcocite concentrate is underway at the Bureau of Mines, Twin Cities Metallurgy Research Center. The new route from concentrate to metal by which the Bureau seeks to eliminate matte smelting and converting includes a two-stage fluid bed treatment. In the first stage, pelletized concentrate containing 32%Cu and 7% S is first desulfurized to less than 1.0% S in an oxidizing atmosphere. In the second stage, the calcine is metallized by reduction with hydrogen. Thereafter, the reduced product plus 10% CaO is routed to a smelting furnace which separates metallic copper from the gangue. Recovery and Cu content at this point are in the 97-98% range. This product must be refined to remove sulfur and iron so the metal is suitable for making wirebar copper. An important feature of the process is fine concentrate pelletization prior to fluid-bed treatment. This permits a shorter reaction time, a decrease in dusting and easier subsequent processing. In a broad sense, sulfide copper pyrometallurgy is a batch sequence in three separate vessels, i.e., a reverberatory furnace to yield matte copper, a converter to produce blister copper and another reverberatory furnace to produce fire-refined copper. Matte-smelting has remained relatively unchanged since it became a universal practice some 50 to 60 years ago. It is now serving a wide range of smelter feed materials, but many concentrates are not immediately amenable to the process. There are abundant copper resources which lack sufficient sulfur and other elements lo sustain the full chemistry involved in matte-smelting. This necessitates adding sulfur to make the product fit the process, and usually none of the sulfur is recovered. From the standpoint of pollution alone, the development of a smelting technique for low-sulfur concentrates not requiring the addition of sulfur would be a significant gain.

Jan 1, 1970

By J. T. Crawford

THE purpose of this paper is to present some data and comparisons regarding three types of Rheolaveur plants washing bituminous coal from the Pittsburgh seam. It deals only with the sections that handle coarse coal. The Rheolaveur system consists of launders or troughs in which coal and its associated impurities are conveyed by water. The impurities, being heavier than the coal, settle toward the bottoms of the launders and are drawn off through specially designed openings called Rheo boxes. Fundamentally, each plant consists of straight-sided, flat-bottomed launders of varying width and length, each launder equipped with one or more Rheo boxes for the removal of high-gravity fractions of the feed that are undesirable in the cleaned coal. Each launder has at least two longitudinal sections, the first with a slope of from 1 1/2 to 4 in. per foot of length, called the classification section. The single-box launder has a classification section followed by a washing section ahead of the box. A two-box launder is a single-box launder followed by a washing section and a second box. The slope of the washing section between the first and second boxes is determined to some extent by tonnage. At the end of the classification section, which may vary from 8 to 15 ft. in length, the slope abruptly flattens out to a slope of from ½ to 1 in. per foot of length. This flatter section of the launder, called the washing section, may vary from a few feet, in a single-box launder, to 15 ft., in a two-box launder.

Jan 1, 1938