Search Documents

By Hansheinz Portisch, Harold Margolin

A surface expansion was found to occur sometime after etching in Ti-A1 alloys containing 9.5 to 12.5 wt pct Al. The structure formed, grew, and disappeared with tzrrze. The surface expansion was followed by microscope observations and interferometric and lattice parameter measurements. Activation energy measurements for the growth of the "expansion structure" and chemical analysis indicated that the phenomenon occurred as a result of hydrogen pzckup during etching. It is proposed that hydrogen initially enters octahedral sites of Ti3Al coherent with a Ti and later shifts to the tetrahedral sites. It is postulated that expansion occurs when hydrogen enters the tetrahedral sites. The expansion structure disappeared, it is proposed, because of diffusion of hydrogen from the surface into the body of the alloy and because of loss of coherency of Ti3Al. In examining Ti-A1 alloys, Ence and arolinl observed markings on the surface of specimens. These markings did not appear after electropolishing only, but rather appeared only after etching. The markings appeared to grow as a function of time after etching and later seemed to disappear. Although the markings had some similarity to precipitates, showing, frequently, a Widmanstatten type of arrangement, the observation that other microstructural markings continue to be seen within the new structure suggested that it was actually not a precipitate. The source of this structure was unknown and an attempt was made in the present investigation to develop some understanding of its nature. It has been labeled expansion structure. 1) EXPERIMENTAL PROCEDURE A) Alloys. Alloys in the range 6.5 to 14.5 wt. pct A1 were studied. Bars, 4 in. sq, forged from Bureau of Mines (73 Bhn) titanium consumably arc-melted 4-lb ingots,' as well as 50-g arc-melted buttons of desired aluminum contents were used. The 50-g buttons also used Bureau of Mines titanium (73 Bhn) and aluminum of 99.99 pct purity. Buttons containing up to 8.5 wt pct A1 were hot-rolled from a furnace at 900' . Those with higher aluminum contents were hand-forged on a titanium anvil, and heated with an oxygen-hydrogen torch in the region of 1200" to 1300°c. Frequent reheating kept the samples at the desired temperature range. After a reduction of about 30 pct, the samples were water-quenched. To eliminate any contamination picked up either during hot rolling or forging, at least 1 mil of the surface of the sample was taken off. B) Heat Treatment. Prior to heat treatment all alloys were vacuum-annealed to remove hydrogen. Samples were annealed at 900' until a vacuum of 10'5 mm Hg was established. After this treatment, the samples were wrapped in molybdenum sheet and heat-treated in argon-filled quartz capsules, which were broken under water or iced brine at the conclusion of the heat treatment. All heat treatments under dynamic vacuum were performed in a rapid-quench furnace. This consisted of a molybdenum-lined quartz tube attached to a vacuum system and through a stopcock to a beaker of water. At the completion of the heat treatment the vacuum stopcock was closed, the furnace shut off, and dropped below the quartz tube. Then immediately the inlet stopcock was opened and water admitted until the tube was filled. The steam formed was allowed to escape through the inlet stopcock. This method was used in heat treatments up to llOO°C. C) Metallography. Specimens for metallographic examination were ground, then electropolished using a Disa Electropol machine with a perchloric acid electr01te. Specimens were etched with R-etch.3 A standard etching time of 3 min was used, with the specimen being agitated during immersion. D) Sample Preparation for X-ray Analysis. Samples 0.2 to 0.5 mm in diam were produced from heat-treated rods which were turned to 2 mm diam on a lathe and then rotation-etched. An etchant consisting of 1 pt HF, 7 pt HN03, and 12 pt HzO was satisfactory. With the rod rotating in a vertical position at 50 to 100 rpm, a needle with uniform dimensions could be obtained. Care had to be taken to insure that the rod was at the center of rotation, otherwise cavitation developed. If a small unevenness developed, it was possible to grind it off with a fine emery paper. E) X-ray Diffraction. All X-ray work was done on a North American Phillips X-ray diffraction apparatus and a Jarrell Ash microfocus X-ray unit. The Phillips unit was used with a copper target and nickel filter. The Jarrell Ash unit was fitted with a cobalt target and iron filter. For the Phillips unit 35 kva and 20 ma were used, whereas for the microfocus unit with the 100-p fixed-focus gun 40 kv and 1.5 ma were used. It was found that alignment of cameras on the Jarre11 Ash unit was very critical. The X-ray beam contains an intense area which is not the beam center. The cameras were aligned with the intense region by monitoring the beam coming out of the camera with a Geiger counter. Adjustments were made until a maximum intensity was obtained. A Phillips diffractometer with a Brown chart recorder furnished some of the lattice parameter data. The divergence slit up to 80 deg 28 was I deg; above 80 deg, a 4-deg opening was used, while the scatter slit was1 deg and the receiving slit had a 0.003-in. opening. The general scanning rate was 1 deg per min, while peaks of special interest were rescanned at -j deg per min. For elevated-temperature X-ray diffraction a Uni-cam High Temperature Camera with a film diameter

Jan 1, 1969

By Ivor Jenkins

PROCESSES employing controlled atmospheres in the heat-treatment of metals and alloys are now well established on an industrial scale, and the general principles involved and the advantages to be gained in the use of the technique have received considerable publicity over a period of years. During this time the greatest emphasis has been on the establishment of the process in industry, the main effort being devoted to development work on various types of atmospheres, their useful fields of application and the design of suitable heat-treatment furnaces in which they are to be used. The various types of controlled atmospheres are fairly well standardized, but there still remains a considerable field for the investigation of related problems, in connection with both the gas-generating equipment and the surface chemistry of the heat-treatment of metals, especially in complex controlled atmospheres. This paper describes certain investigations of this nature that were carried out in England up to 1939. The development of processes employing controlled atmospheres has been associated to a very large extent with the heat-treatment of steels, both because of the major importance of steel in industry and the many diverse and difficult problems of surface chemistry involved when steels of such a wide range of composition are heated in the presence of active gases Controlled atmospheres such as dissociated and burnt ammonia or charcoal gas are used in the heat-treatment of low-carbon and high-carbon steels, but from certain points of view a suitable atmosphere generated by the partial combustion of city gas is to be preferred. Both the ammonia derivatives are comparatively expensive, and even if the burnt ammonia is regenerated, thereby reducing operating costs, the capital expenditure of the gas plant may make it prohibitive for the smaller type of furnace installation. Charcoal-gas generators are not without their operating difficulties: especially those associated with the quality of the charcoal, clinker formation and the removal of carbon dust from the generated gas. City gas has the advantage of being comparatively cheap and "on tap" in most if not all industrial centers. The use of raw city gas as a protective atmosphere in the heat-treatment of steels has been described,1 but it presents certain difficulties because of its complex composition and its explosive nature when mixed with air. These factors, together with the tendency toward sooting at elevated temperatures, arising mainly from the hydrocarbon gases present, all militate against its use as a protective atmosphere in industrial furnaces. The following analysis, based on the analyses of city gas in different localities in Great Britain, indicates the wide limits existing

Jan 1, 1947

By G. S. Cole, G. F. Bolling

ThIS note accompanies a study of grain structure changes in metal ingots produced by the alteration of fluid motion.1 Although the Prandtl Number of aqueous solutions is much higher than that for metals, it is quite instructive to see the simulation of freezing, as pointed out by Jackson and coworkers.2-4 Accordingly we have observed the effects of natural thermal convection, the changes induced by a steady-state rotation in one direction, and the changes under oscillation.' Temperature measurements were made under duplicate conditions whenever the visual observations appeared interesting. A solution of 15 pct NH4C1 in water was chosen. In each case the solution was preheated to 90°C in a 4-in.-diam Pyrex beaker filled to a level of about 5-in. depth and covered to prevent convective air cooling. The beaker was then placed in a container of iced brine, suitably arranged on a rotating table for movement about its cylindrical axis. Upon immersion in the brine under static conditions, fluid flow was observed near the wall of the beaker before the onset of crystallization, which generally commenced only after the temperature fell to 51.5"C. The region of flow extended about 1 mm from the wall and could not be observed elsewhere. The measured radial temperature increased sharply within 1 cm from the wall and thus over a distance considerably greater than that observed for the flow. However, we note that this difference of approximately one order of magnitude between hydrodynamic and thermal boundary layers should be expected for aqueous solutions, in contrast to metallic liquids. Beyond this layer the temperature was isothermal at a given height and in general nearly 10°C warmer than at the wall. The overall visual observation was therefore supported quite well by temperature measurement. There was also a vertical temperature gradient of nearly 2°C per cm throughout the liquid increasing from the colder bottom; this of course could not be observed visually. Eventually crystals precipitated from solution. (It

Jan 1, 1968

By J. G. Bartram

Jan 1, 1934

By Paul Hunt

UP to June, 1923, the Park-Utah mine had shipped about 94,000 tons of a direet-smelting ore of a gross value of $4,200,000, or about $45. a ton. These values were in gold and silver only, although the ore carried small amounts of lead, copper and zinc. Freight, treatment and deductions had averaged $15.40 a ton. At the expiration of the Pittman Silver Act there was in sight about 30,000 tons of a similar ore with a gross value of about $15 a ton in gold and silver, and a large body of partly developed lead-zinc ore of a gross value of about $20 a ton, 40 per cent. of which was represented by the lead-zinc content and the balance by the silver and gold. Mine costs had been high during the life of the Pittman Act, but as a large part of the profits had gone into equipment of the mine and the orebodies were large and had good walls, we knew that mine costs could be greatly reduced. We were therefore faced by the necessity of getting lower freight and smelter rates or of concentrating the ore. We did obtain better freight rates on lower grade ore, and a favorable smelting rate on the small tonnage of siliccous silver-gold ore, but this smelter rate could not be applied to the lead-zinc ore with any profit to ourselves. The Judge mill of the Park City Mining & Smelting Co., with which we were affiliated, was running to capacity; if we built our own mill it ineant a 5-mile freight haul to a satisfactory millsite and a year's delay. Fortunately, the International Sillelting Co. had just inherited a mill at Tooele which, with some changes, was about double the catpscity required for its own ores. Flotation tests were run on Park-Utah ore and a contract entered into with a low base treatment charge per ton, the tariff being largely fixed by the metallurgical deductions. This contract has been admirably calculated so that the miner can follow a lean orenbody to its limit. Such a procedure has no doubt made it difficult for the smelting company at times, but it has resulted in finding ore extensions that otherwise might have been missed, so In the long run it has profited too. A flat rate per ton would have been like mining up to the claim endlines in a great many of the stopes. In order to offer such a contract it can be inferred that the smelting company must have been able to make high reeoveries and high-grade products on a very lean ore.

Jan 1, 1928

By W. Philippoff

ALTHOUGH Gaudin1 and more recently Sutherland2 have calculated the probability of collision of a falling mineral particle with a rising bubble, there is no published information concerning the details of the mechanism of attachment of a collector-coated particle to a bubble. During the past year the writer has developed a theory for the mechanism of attachment, which has been substantiated experimentally. Funds for the investigation and for some of the equipment used have been supplied by the Mines Experiment Station of the University of Minnesota. Motion picture studies of the phenomena involved in the collision between mineral particles and bubbles, such as those of Spedden and Hannan," show that the contact can be completed within 0.3 millisec. Formulas developed for rigid bodies have hitherto been used' for the calculation of the motion of bubble and particle, but it is obvious that a bubble cannot be regarded as a rigid body. On the contrary, Spedden and Hannan's pictures show a great degree of deformation during the collision. The time of attachment was calculated as the time the particle drifted past the bubble. Time of Collision The theory presented in this paper enables calculation of the time of collision, using the concept that the bubble, or more generally, a liquid-air interface, acts as an elastic body. The elasticity, defined as the restoring force on a mechanical deformation, is caused by the surface tension and is the result of the principle of the minimum of free surface energy. It is well known that an elasticity together with a mass determines a frequency of vibration. The vibrations of jets and drops caused by the elasticity of the interface are known to comply exactly with the classical theory of capillarity.' However, the vibrations of isolated bubbles, as distinct from foams, have not been investigated previously. The following equation, presented elsewhere,' has been deduced for these frequencies: 3_____________________ fB = 9.20.vV.vn. (n-1).(n+2)/8 [I] in which fB is the frequency of a harmonic of the bubble in cycles per second, V the volume of the bubble in cc, n a number determining the order of the harmonic, and n = 2 the basic vibration. The first (basic) harmonic describes a change of the spherical bubble to an ellipsoidal bubble. The higher harmonics are more complicated, for the circumference of the bubble is divided approximately into as many parts as the order of the harmonic. As an example, Spedden and Hannan's published motion picture of a vibrating bubble corresponds to the sixth harmonic. Eq 1 shows that only the first and third harmonics are simple multiples (1 and 3), all the others being irrational fractions of the basic frequency. This means that the shape of the vibration can change with time and is in general unsym-metric in respect to the time axis. Such conditions prevail when there is a distributed elasticity or mass, as in the case of vibrating membranes or rods. The constant 9.20 is valid for water at room temperature, but a general solution involving the physical constants of the liquid has not been found. The case of the floating particle is much easier to treat than that of the bubble. It can be assumed that the elasticity is caused exclusively by the interface and that the mass is concentrated in the particle together with some adhering water. The following expression for the frequency of a system of one degree of freedom can be applied: fP = -1/2-vE/m [2] Here fp is the frequency of the particle vibration in cycles per second, E the elasticity in dynes per cm, and m the mass in grams. The classical theory of impact phenomena gives the time of collision during the striking of a spring (in this case the surface of the bubble) by a mass, as: t, = 2/f = nvm/E [3] It is now possible to develop an expression for the elasticity of a floating cylindrical particle. The force equilibrium of a cylinder floating end on at the air-liquid interface is given by the well-known equation (Poisson7 1831) P = /4 D2-pL-g-h + D.y sin a [4] which accounts for the buoyancy and the action of the surface tension where P is the force acting on the particle in dynes (weight-buoyancy), D the diameter of the cylinder in cm, PL the density of the liquid in grams per cc, g the acceleration of gravity = 981 cm per sec2, h the depression of the cylinder below the surface of the liquid in cm, y the surface tension in dynes per cm and a the supporting angles or the one required to insure equilibrium, a being smaller than the contact angle 0. Although demonstrated by Poisson, it has not

Jan 1, 1953

By W. Philippoff

ALTHOUGH Gaudin1 and more recently Sutherland2 have calculated the probability of collision of a falling mineral particle with a rising bubble, there is no published information concerning the details of the mechanism of attachment of a collector-coated particle to a bubble. During the past year the writer has developed a theory for the mechanism of attachment, which has been substantiated experimentally. Funds for the investigation and for some of the equipment used have been supplied by the Mines Experiment Station of the University of Minnesota. Motion picture studies of the phenomena involved in the collision between mineral particles and bubbles, such as those of Spedden and Hannan," show that the contact can be completed within 0.3 millisec. Formulas developed for rigid bodies have hitherto been used' for the calculation of the motion of bubble and particle, but it is obvious that a bubble cannot be regarded as a rigid body. On the contrary, Spedden and Hannan's pictures show a great degree of deformation during the collision. The time of attachment was calculated as the time the particle drifted past the bubble. Time of Collision The theory presented in this paper enables calculation of the time of collision, using the concept that the bubble, or more generally, a liquid-air interface, acts as an elastic body. The elasticity, defined as the restoring force on a mechanical deformation, is caused by the surface tension and is the result of the principle of the minimum of free surface energy. It is well known that an elasticity together with a mass determines a frequency of vibration. The vibrations of jets and drops caused by the elasticity of the interface are known to comply exactly with the classical theory of capillarity.' However, the vibrations of isolated bubbles, as distinct from foams, have not been investigated previously. The following equation, presented elsewhere,' has been deduced for these frequencies: 3_____________________ fB = 9.20.vV.vn. (n-1).(n+2)/8 [I] in which fB is the frequency of a harmonic of the bubble in cycles per second, V the volume of the bubble in cc, n a number determining the order of the harmonic, and n = 2 the basic vibration. The first (basic) harmonic describes a change of the spherical bubble to an ellipsoidal bubble. The higher harmonics are more complicated, for the circumference of the bubble is divided approximately into as many parts as the order of the harmonic. As an example, Spedden and Hannan's published motion picture of a vibrating bubble corresponds to the sixth harmonic. Eq 1 shows that only the first and third harmonics are simple multiples (1 and 3), all the others being irrational fractions of the basic frequency. This means that the shape of the vibration can change with time and is in general unsym-metric in respect to the time axis. Such conditions prevail when there is a distributed elasticity or mass, as in the case of vibrating membranes or rods. The constant 9.20 is valid for water at room temperature, but a general solution involving the physical constants of the liquid has not been found. The case of the floating particle is much easier to treat than that of the bubble. It can be assumed that the elasticity is caused exclusively by the interface and that the mass is concentrated in the particle together with some adhering water. The following expression for the frequency of a system of one degree of freedom can be applied: fP = -1/2-vE/m [2] Here fp is the frequency of the particle vibration in cycles per second, E the elasticity in dynes per cm, and m the mass in grams. The classical theory of impact phenomena gives the time of collision during the striking of a spring (in this case the surface of the bubble) by a mass, as: t, = 2/f = nvm/E [3] It is now possible to develop an expression for the elasticity of a floating cylindrical particle. The force equilibrium of a cylinder floating end on at the air-liquid interface is given by the well-known equation (Poisson7 1831) P = /4 D2-pL-g-h + D.y sin a [4] which accounts for the buoyancy and the action of the surface tension where P is the force acting on the particle in dynes (weight-buoyancy), D the diameter of the cylinder in cm, PL the density of the liquid in grams per cc, g the acceleration of gravity = 981 cm per sec2, h the depression of the cylinder below the surface of the liquid in cm, y the surface tension in dynes per cm and a the supporting angles or the one required to insure equilibrium, a being smaller than the contact angle 0. Although demonstrated by Poisson, it has not

Jan 1, 1953

By W. Chubb

By measuring the hardness of metals at temperatures just above and just below their allotropic change point, it has been established that crystal structure has a real effect upon the strength of metals. The DPH of cobalt, iron, titanium, uranium, and zirconium have been measured at temperatures up to 1000°C. It was found that the body-centered-cubic crystal structure is always the softer structure when it is involved in an allotropic transformation. The close-packed and more complex structures are inherently harder, and may be expected, therefore, to be better base materials for high strength alloys. IT has been observed that for metals with nearly the same melting point (i.e., tin and lead, magnesium and aluminum) the metal with the more complex crystal structure has a higher tensile strength and hardness. It might be asked whether this effect is really caused by the difference in crystal structure; and, if so, just what is the contribution of crystal structure to the strength of these metals. A qualitative answer to these questions can be obtained by measuring the change in hardness produced by the change in structure in metals exhibiting allotropic forms. The evidence for changes in mechanical properties during allotropic transformations is rather meager. In 1909, Rosenhain and Humfrey' observed that "ß" iron showed much less deformation at the transformation temperature than a iron. By means of a torsion test, Lee found that iron bars were "critically plastic" at the a-7 transformation temperature. Sauerwald and Knehans have shown that the dynamic hardness of iron increases between 900" and 1000°C. In 1930, Albert Sauveur' presented data on the hardness, tensile strength, and torsional strength of pui-e iron up to 1000°C. He concluded, "At 900°C, the a iron transforms into y iron, and this is accompanied by increased strength and stiffness and decreased ductility." The same year, Schischokin" obtained data on the hardness of thallium at temperatures above and below its transformation temperature. His data are replotted on semilogarithmic coordinates as Fig. 1. The fact that his data fall on straight lines in this type of plot is believed to attest to the purity of his metal and the accuracy of his results. In 1941, Nadai and Manjoine" obtained tensile data on pure iron with an indicated increase in strength at about 900°C. These experiments make it quite evident that changes in mechanical properties occur when a metal transforms from one crystal structure to another; but, except for Schischokin's data on thallium, none of the measurements seem accurate enough to determine the relative magnitude of the mechanical property change. Materials The metals that have been examined for changes in hardness during transformation include l—as- deposited commercial electrolytic cobalt about 99.7 pct pure, 2—Armco ingot iron, 3—are-melted iodide titanium of a purity in excess of 99.8 pct, 4—uranium of a purity in excess of 99.5 pct, 5—are-melted iodide zirconium of a purity in excess of 99.8 pct, 6—annealed, 0.08 pct C, rimmed steel, and 7—commercially pure RC55 titanium. While the purity of the first five of these materials leaves something to be desired, it will be noted that the observed hardness discontinuities occurred at the accepted transformation temperatures. (These temperatures are indicated by vertical arrows in Figs. 1 and 3 through 7.) The last two materials are commercial alloys introduced to show the effect of minor alloying elements upon the hot hardness curve. Apparatus Hardnesses at elevated temperatures were determined by means of a vacuum hot hardness machine. A diagram showing the basic features of this machine appears as Fig. 2. This machine is essentially a deadweight hardness .machine in a furnace within a vacuum chamber. The sapphire-tipped indentor

Jan 1, 1956

By Richard Downs, Stephen P. Burke

The oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combustion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the conditions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 2H2O + 7O2 ? 2FeSO4 + 2H2SO4 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to disclose any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1938

By Richard Downs, Stephen P. Burke

The oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combustion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the conditions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 2H2O + 7O2 ? 2FeSO4 + 2H2SO4 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to disclose any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1938

By E. C. Nelson

An equation is derived for calculating approximately the solubility of nitrogen in an alloy steel over a temperature range from 1200" to 1900°C using data on the effects of alloys on the activity coefficient of nitrogen in iron at 1600°C. Calculated values are compared with experimental data. STUDIES involving the solubility of nitrogen in complex iron alloys have been aided by a system devised by Lanenberg for calculating the solubility of nitrogen in ternary and higher alloys of iron at 1600C using available data on the activity coefficient of nitrogen in binary alloys. Calculated nitrogen solubilities agree well with experimental determinations on complex alloys,' and the calculation procedure is useful when experimental data on specific alloys are not required. A method for extending calculations of nitrogen solubilities in alloy steels to temperatures other than 1600°C would be useful because of the paucity of experimental data in this area. Assumptions which must be made to permit this calculation introduce an element of approximation; however, the calculation is useful in cases where a large number of alloys and temperatures are under consideration, and the precision of experimental measurements is not required. The activity coefficient can be freed from the isothermal restriction of Langenberg's calculation if it is assumed that the solution is "regular". This is a reasonably good assumption for solutions of nitrogen in iron alloys, because usually they are dilute and the heat of solution is relatively small. The presence of large amounts of certain alloying elements would make this assumption less tenable.3 One of the properties of a regular solution is: when "f" is the activity coefficient of a solute and "T" is the temperature in OK. If the activity coefficients at temperatures T and T2 are denoted by subscripts 1 and 2 respectively: The activity coefficient of nitrogen in a complex alloy then can be calculated at any temperature from the sum of the effects of the other solutes on the activity coefficient of nitrogen at 1600°C. It will be convenient to incorporate this expression into an equation which will give directly the logarithm of the solubility of nitrogen at any temperature in the presence of alloys. Two constants, the solubility of nitrogen in pure iron at 1600 "C and the partial molar heat of solution of nitrogen in iron are required. The heat of solution value of 1400 cal at 1600 °C quoted by Kubaschewski and vans will be used. The accuracy of the calculation will suffer if the heat of solution should change materially with temperature. In the absence of experimental data on the temperature dependence of this quantity, it will be expedient to restrict the application of the calcula-

Jan 1, 1963

By F. R. Brotzen, J. Taranto

SEVERAL investigators have computed stacking-fault concentrations from X-ray diffraction data.'-' The method generally employed relates the line shift to the stacking-fault probability. In this investigation platinum filings of 99.99 pct purity screened to -325 mesh were studied after having been subjected to various annealing treatments. The lines were measured on a General Electric XRD-5 spectrogoniometer using CuK, radiation. The centroid of the broad reflections was determined by the method proposed by pike.' The stacking-fault probability was calculated by the formula given by Warren and warekois,3 with the assumption that all stacking faults were on the (111). Various high-angle reflections were used, but most data collected refer to the shift in the (400) reflections. When the filed platinum powder was annealed at 1200°C for 20 min the stacking fault concentration was too small to be detected. The stacking-fault probability in freshly filed specimens, as determined by the line shift relative to the annealed specimen, was about 0.016, Fig. 1. If the faults would be created only by extended dislocations, the dislocation density in the filed specimen would be about 3X1012 cm-2. The average stacking-fault width of about 21 which was used in this computation, is that given by Thornton and Hirsch.7 The mechanism by which stacking faults are annihilated during annealing is not yet fully understood. The isothermal results obtained do not seem to support the simple hypothesis of a first-order decay. On the other hand, the analysis by Kuhlmann, Masing, and Raffelsieper8 for the loss of dislocations during recovery agrees much better with the experimental data of this investigation. This analysis yields an activation energy of 29 ± 8 kcal per mol for the disappearance of stacking faults in cold-worked platinum during annealing. Even if one takes into account the lack of accuracy inherent in this X-ray method, the activation energy found is substantially less than that of self-diffusion in platinum, i.e., 61.6 kcal per mol.9 The results therefore suggest that processes other than dislocation climb, which involves the activation energy of self-diffusion, are responsible for the loss of stacking faults in platinum during annealing. The broad reflection lines became sharper early in the recovery process, Fig. 1. The sharpening occurred well before the stage during which stacking faults disappear. This lends support to Nowick's10

Jan 1, 1962

By D. J. Weintritt, J. C. Cowan

Methods of studying oilfield mineral .scale deposition in the laboratory do not work for barium sulfate because only small nonadhering crystals ore formed. On the other hand, barium sulfate scale found in down-hole or surface equipment is strongly adhering and may contain very large crystals. Results suggest that most of the difference derives from the extremely low .solubility of barium sulfate. Firm adherence of scale and the consistent development of oriented crystals 100 microns and larger suggest a relationship between scale adherence and crysta1 growth. Data from this study indicate some reasons for barium sulfate's occurring as a deposit in oilfield waters. The unique characteristics as well as the associative properties of barium sulfate scale as related to calcium carbonate and calcium sulfate ere shown. INTRODUCTION The first observed deposition of barium sulfate scale in oilfield production equipment is unknown but probably coincides closely with the beginnings of the oil industry itself. Moore' described barite oolites in some producing wells in the Saratoga field, Tex., in 1914. Currently, positive identification of barium sulfate deposition is recorded in most of the major oil-producing areas of the United States. As efforts continue to identify the composition and functions of the materials found in scale deposits, the geographic and economic importance of the part played by barium sulfate will become even more important. This belief is based on the following Facts. 1. Many oil fields in the U.S. are in or entering their mature phase and the volume of produced water is increasing; thus, the cumulative effects of low-solubility minerals become more significant. 2. Secondary recovery techniques and increased emphasis on waste disposal systems require controlling the behavior of all constituents of water to prevent formation plugging. 3. The more general use of instrumental analysis has reduced the time and improved the accuracy of complete scale and water analysis. 4. Once formed, barium sulfate scale is resistant to present methods of chemical removal; therefore, costly mechanical methods are necessary. Thus, new methods of prevention and control will require specialized chemical techniques and better knowledge of the causes of scaling. Consider the results of some simulated field deposition studies illustrating this need (Fig. 1). The studies utilized a Scale Deposition Test Cell* and each coupon was exposed to 8,000 ml of a 300 me/liter solution of the various types of mineral scale. All tests were conducted at 140F. Only the calcium sulfate and calcium carbonate deposited scale. The solution containing 300 me/liter of barium sulfate exhibited copious amounts of precipitate, but none of the precipitate adhered. The fluids from the effluents were also allowed to impinge on glass slides. Fig. 1 shows the relative adherence of the three types of scale on unetched glass. The barium sulfate failed to deposit in the same manner as the calcium carbonate and calcium sulfate solutions.

By L. H. Robinson

A proposed method of drilling utilizes sequential detonation of two types of explosive charges delivered to the hole by a conventional drilling fluid through pipe. A shaped charge first produces a long thin hole. A second charge, called a gauging charge, is pumped into the thin hole, explodes, and enlarges it to full gauge. In one suggested configuration, the explosives are contained in cylindrical capsules 4- to 5-ft long. A drilling head is positioned 2- to 3-ft off bottom. When a capsule is pumped to the bottom of the hole and stops, pressure inside the drill pipe increases and differential pressure detonates the explosive. Primacord along the length of the capsule disintegrates the capsule. The debris circulates out of the hole with the drilling fluid. The gauging-charge action was examined using 2-ft cubes of Berea sandstone. The sandstone (18 per cent porosity) was vacuum-saturated with water and surrounded by concrete. To prevent reflected tensile pulses, the acoustical impedance of the concrete matched that of the sandstone. A 750-psig pressure was applied to a drilling fluid within a shaped-charge-formed hole before detonating the gauging charge. In these tests, 190 gm of rock were removed for each gram of explosive detonated. A similar series of experiments on low-porosity (0.40 per cent) metamorphic limestone provided a more rigorous test. Extensive fracturing from the gauging-charge action prevented an estimate of the volume of the expanded hole. The diameter of the hole was irregular, ranging from about 2 to 4 in, or about fivefold larger than the hole created by the shaped charge. INTRODUCTION In the past, explosives have found a varied but somewhat limited use in the oil field. An early well stimulation technique, still in use today, in vo lves shooting ni troglycerin to en large the borehole and to increase matrix permeability near the wellbore. Bullets and jets are now the conventional method of perforating casing and tubing. Detonations are frequently used to "back off" or "shoot off" stuck pipe and, of course, seismo-graphic work has long depended on explosive-generated pulses to find attractive earth structures. Efforts to use explosives in drilling operations have received limited examinations1-3 which, in one respect, is surprising because explosives offer one way to transmit large amounts of energy directly to the bottom of the hole. Recently, Ostrovskii l described a Russian method of drilling with explosives that utilizes small capsules containing explosives which are pumped into the mud stream to the bottom of a borehole. As the capsules leave the end of the drill pipe, a detonation mechanism is armed. Impact detonates the explosive. In another configuration, two liquids (an oxidizing agent and fuel) in the capsule are separated by a frangible membrane. Separately, the liquids are nonexplosive. Near the bottom of the drill pipe, the capsule passes through a narrow constriction which ruptures the membrane. The mixing of the liquids produces an explosive. Impact is again used to detonate the explosive. About the time Ostrovskii was developing his method, Humble Oil & Refining Co. was independently doing research on another explosive drilling concept based on the sequential detonation of two types -of explosive charges. The proposed technique consisted of alternately pumping a shaped charge and then a "gauging charge" down a well. The shaped charge should drill a long, tapered hole, and the gauging charge should expand it to full gauge. This paper presents the visualized drilling concept and gives results of laboratory work which showed that sequential firing of charges can form hole at an attractive charge-to-rock removal ratio. An important finding was that increased environmental pressure, which is to be expected in wells, increases rock removal efficiency of the gauging charge.

Jan 1, 1966

By J. M. W. Mackenzie, M. H. Buckenam

Flotation experiments using stearic, oleic, linoleic, linolenic, and ricinoleic acids and naturally occuring products rich in these acids as collectors for calcite are described. The results confirm the validity of the rule of Hukki and Vartiainen relating the collecting power and unsaturation of the C18 acids. Reasons for this relationship are discussed and a close relationship between mineral depression and critical micelle concentration is reported. It has long been recognized that the unsaturated fatty acids are in general superior flotation collectors to their saturated homologues. Whereas earlier workers concentrated on saturated and monoethe-noid acids, recent investigations have centered on oleic, linoleic, linolenic, and the substituted mono-ethenoid acid: ricinoleic. From studies of the collecting properties of palmitic, oleic, linoleic, and linolenic acids on ilmenite, rutile, hematite, and magnetite, Hukki and Vartiai-nenl concluded that the collecting power of fatty acids increased with unsaturation of the hydrocarbon chain. Sun, Snow, and Purcel12 investigated the collecting properties of unsaturated fatty acids as collectors for phosphate ores and concluded that the collecting power increased with increasing unsaturation of the hydrocarbon chain up to two double bonds and that further unsaturation decreased the collecting power. More recently Sun3 studied the collecting power of the C18 fatty acids stearic, oleic, linoleic, and linolenic on 37 minerals. The results of these experiments with a few exceptions showed that the collecting power of the acids increased in the order stearic, oleic, linoleic, and linolenic. The relative collecting powers of linoleic and linolenic acids were in many cases altered by the cleanliness of the mineral surface prior to flotation. Sun concluded that linolenic acid may become oxidized by atmospheric oxygen during flotation, a reaction which would reduce its effectiveness as a collector. This deduction is supported by Gaudin and Cole4 who concluded that oleic and linoleic acids do not undergo appreciable oxidation of the double bonds during flotation but that the linolenic acid double bonds are measurably affected. The most complete investigation on the influence of hydrocarbon chain unsaturation on the collecting properties of fatty acids is that of Kivalo and Lehm~svaara.~ These workers using linolenic acid of a higher purity than Hukki and Vartiainen showed that this acid was superior to oleic and linoleic acids as a collector for magnetite. They also found that ricinoleic acid was a more effective collector for this mineral than the other acids investigated, an observation particularly apparent at high collector concentrations. Seeking to explain the superiority of the unsaturated acids these authors considered the effects of critical micelle concentration, surface activity, hydrolysis, and cross sectional area of the hydrocarbon chain in relation to unsaturation. Using what, according to the results of Caviere are erroneous surface tensions of the soap solutions of these acids, they concluded that the surface activity decreases and the critical micelle concentration increases with increasing unsaturation. In view of the data of Cavier, whose results show that surface activity of these soaps increases with unsaturation, the deductions of Kivalo and Lehmusvaara are open to criticism. The degree of hydrolysis of the soap solutions as measured by Kivalo and Lehmusvaara decreases as the unsaturation of the fatty acid increases, a result which helps to explain the superiority of unsaturated acids as collectors. In view of the superiority of unsaturated acids as collectors for many minerals, attention has been directed towards the utilization of fatty acid raw materials such as tall oils and linseed oils which contain considerable quantities of these acids. This paper describes test work to determine the effect of unsaturation of the hydrocarbon chain on the collecting properties of fatty acids on calcite, and includes comparable test work using natural products rich in unsaturated acids. TEST WORK Reagents: The pure fatty acids used were oleic, linoleic, and linolenic. Of these, oleic was supplied by British Drug Houses Ltd. and the others were produced by the Hormel Inst. When not in use these

Jan 1, 1961

By Carl G. Hogberg

During recent months, the acute shortage of steel scrap has necessitated the use of higher percentages of hot metal in the open-hearth charge. With these higher percentages, the sulphur content of hot metal has become an increasingly important factor in the control of the quality of steel. Thus, the blast-furnace operator is faced with a demand not only for more output but for a higher quality of product. More than go per cent of the sulphur charged into the blast furnace is contained in the coke. With the tremendously increased demand, the trend of coke quality has been toward higher sulphur, higher and more variable ash, and poorer physical characteristics. This has been brought about by less selective coal mining, increased production rates in coke plants and resumption of operations of many beehive ovens. In a single month last year, one blast-furnace plant in the Pittsburgh district operated with coke obtained from 52 sources. The effect of variability and quantity of coke ash on blast-furnace operation is well known. The improved results obtained with furnaces operating on coke made from washed coals compared with results on coke made from raw coals is ample proof of the effectiveness of low and uniform ash. Coal-washing plants, however, require a large capital expenditure, and are impractical for most of the large number of small producers, whose operations are confined chiefly to periods of abnormally high demand. Furthermore, not all coals are physically adaptable to washing. Principles 01 Iron Desulphurization in Furnace Although investigations of the blastfurnace process have not clearly revealed the detailed mechanism of iron desulphuri-zation within the furnace, they have been sufficiently extensive to permit a postula tion of the following general principles: 1. Iron, in its travel from furnace top to hearth, continues to pick up sulphur until it has reached tuyere level. The zone of iron desulphurizatioil is relatively narrow, being confined to a vertical distance extending zapproximately from tuyere level to the iron-slag interface in the hearth.' 2. Combustion of coke is confined to spherical zones extending approximately 40 in. from the nose of each tuyere.= Coke ash is released as the coke bums in these combustion areas. 3. With a constant amount of sulphur in the charge, the sulphur content of the metal product is a function of hearth temperature, final slag analysis, slag viscosity, and slag volume. Both hearth temperature and slag analysis affect slag viscosity. For a slag of constant analysis, viscosity always decreases with an increase in temperature;

Jan 1, 1943

By F. M. Lewis, J. F. Meyers

This second progress report of grinding presents comments regarding ball consumption and data pertaining to the hydroscillator, which is closed circuited with the tricone mill. A study and postulate of how balls function is presented. The paper summarizes cost reduction obtained by the method of "grinding for the tail race" rather than for "mesh tons." AT the Regional meeting in Columbus, Ohio, in September 1949, the authors presented a progress report of the first year's operation with a Hardinge tricone mill in closed circuit with a Dorr hydroscillator. The present report covers our findings on this grinding circuit to January, 1950. In order to clarify our position, the authors wish to state that no invention or discovery is claimed. The Tennessee grinding circuit is simply an engineered arrangement of known equipment arranged to incorporate all of the recognized efficiency factors of comminution as they are known today. As we concluded our first report, it was not clear how effective the Tennessee mode of operation would be on harder ores. The only information we had at that time was that the Bond grindability test at 48-mesh gave 6.04 g of undersize per revolution. A later test on the same sample at 100-mesh reduced this to 2.04 g, which is definitely in the harder ore class, and which makes the reported 8.80 kw-hr per ton of —200-mesh produced a very creditable figure. Hydroscillator Operation The machine as now developed has proved dependable and easy to operate. It starts easily under full load and responds quickly to operating adjustments. The hydraulic holes in the oscillating plate do not plug when shut down under full load. Absolutely clean hydraulic water is essential. An Elliott water screen or similar device should be an essential part of the machine to keep all scale and trash of all kinds from the hydraulic compartment. The shift operators have expressed approval of the machine. In table I we show a typical screen analysis of the hydroscillator rake sand as compared to conventional classifier rake sand on our ore. We have previously reported that of the 28.7 pct reduction in power, the hydroscillator contributed 6 pct, on a —200-mesh basis. This is a conservative figure. Some of our test runs indicated that the saving was as high as 10 pct. Laboratory studies by the Dorr Co. engineers indicate that still greater efficiency is possible. Nevertheless, the 10-ft plate is overflowing 2100 tons per day at 3 to 4 pct + 65-mesh, which is a very creditable performance by

Jan 1, 1951

By R. H. Cox, A. S. Allen, James Paone

The southwestern Illinois communities of Belleville and Maryville lie within the greater metropolitan area surrounding St. Louis. Missouri. They also lie within that part of the Illinois coal basin where the Number 6 coalbed has been mined for more than a century. About half the coal was left as pillars to support the ground surface. Years later, however, damaging movements are affecting buildings, streets, and public utilities in some areas. They are generally believed to be related to abandoned mine workings. The threat of continued or increasing incidence of damage raises the need to explore other subsidence-control measures for protecting affected areas with high population density. Because of experience gained in a subsidence-control program of backfilling abandoned coal mines in the Applachian region and in Rock Springs, Wyoming, the Bureau of Mines was called upon to investigate the subsidence occurrences at Belleville and Maryville, and recommend protective measures. Funds ware appropriated for the Bureau to initiate subsidence-control projects at two residential sites in Belleville and one in Maryville. Subsurface investigation of the sites by diamond core drilling revealed two conditions that differ from those encountered at most sites of previous subsidence-control projects. The mine workings were found to be dry and the mine floor consisted of soft underclay which characteristically loses strength with increase of moisture. It had been anticipated that water would have percolated into the mine workings at one .or more of the sites through cracks resulting from subsidence. Under such conditions Bureau engineers believed that injection of mine waste by the pumped; slurry technique3 would provide support and stabilize any movements initiated by the softening of the clay. With discovery that the underclay deposits at the three sites have apparently not been exposed to water since the mines were operating, hydraulic backfilling of any type was considered inadvisable on the basis of present knowledge. To avoid introducing water, a portable pneumatic system is being devised for injecting minus 0.01 27 m (1/2 in.) mine waste into the mine workings. Machines for pneumatic backfilling have been used in Europe not only for subsidence protection but also for strata control, for reducing spontaneous combustion and methane accumulation, and as a means of waste disposal. The Bureau experimented with a pneumatic machine in the Northern anthracite field of Pennsylvania in the 1950's. Previously pneumatic machines have been installed in active mine workings discharging from horizontal pipelines which conveyed air- borne material into rooms to be filled. In the present adaptation to abandoned mines, the machine and air compressor will be operating at the surface, to impel material vertically down injection boreholes with sufficient air pressure to disperse fill material laterally in mine workings at the base of injection holes. Large diameter access and ventilation boreholes will be provided at one site for entry into mine workings to observe backfilling progress. The Belleville and Maryville projects are part of the Mined Land Demonstration Program of the Bureau of Mines. The Illinois State Geological Survey and Department of Mines and Minerals are furnishing technical support.

Jan 1, 1979

By Carl G. Hogberg

During recent months, the acute shortage of steel scrap has necessitated the use of higher percentages of hot metal in the open-hearth charge. With these higher percentages, the sulphur content of hot metal has become an increasingly important factor in the control of the quality of steel. Thus, the blast-furnace operator is faced with a demand not only for more output but for a higher quality of product. More than go per cent of the sulphur charged into the blast furnace is contained in the coke. With the tremendously increased demand, the trend of coke quality has been toward higher sulphur, higher and more variable ash, and poorer physical characteristics. This has been brought about by less selective coal mining, increased production rates in coke plants and resumption of operations of many beehive ovens. In a single month last year, one blast-furnace plant in the Pittsburgh district operated with coke obtained from 52 sources. The effect of variability and quantity of coke ash on blast-furnace operation is well known. The improved results obtained with furnaces operating on coke made from washed coals compared with results on coke made from raw coals is ample proof of the effectiveness of low and uniform ash. Coal-washing plants, however, require a large capital expenditure, and are impractical for most of the large number of small producers, whose operations are confined chiefly to periods of abnormally high demand. Furthermore, not all coals are physically adaptable to washing. Principles 01 Iron Desulphurization in Furnace Although investigations of the blastfurnace process have not clearly revealed the detailed mechanism of iron desulphuri-zation within the furnace, they have been sufficiently extensive to permit a postula tion of the following general principles: 1. Iron, in its travel from furnace top to hearth, continues to pick up sulphur until it has reached tuyere level. The zone of iron desulphurizatioil is relatively narrow, being confined to a vertical distance extending zapproximately from tuyere level to the iron-slag interface in the hearth.' 2. Combustion of coke is confined to spherical zones extending approximately 40 in. from the nose of each tuyere.= Coke ash is released as the coke bums in these combustion areas. 3. With a constant amount of sulphur in the charge, the sulphur content of the metal product is a function of hearth temperature, final slag analysis, slag viscosity, and slag volume. Both hearth temperature and slag analysis affect slag viscosity. For a slag of constant analysis, viscosity always decreases with an increase in temperature;

Jan 1, 1943

By F. M. Lewis, J. F. Meyers

This second progress report of grinding presents comments regarding ball consumption and data pertaining to the hydroscillator, which is closed circuited with the tricone mill. A study and postulate of how balls function is presented. The paper summarizes cost reduction obtained by the method of "grinding for the tail race" rather than for "mesh tons." AT the Regional meeting in Columbus, Ohio, in September 1949, the authors presented a progress report of the first year's operation with a Hardinge tricone mill in closed circuit with a Dorr hydroscillator. The present report covers our findings on this grinding circuit to January, 1950. In order to clarify our position, the authors wish to state that no invention or discovery is claimed. The Tennessee grinding circuit is simply an engineered arrangement of known equipment arranged to incorporate all of the recognized efficiency factors of comminution as they are known today. As we concluded our first report, it was not clear how effective the Tennessee mode of operation would be on harder ores. The only information we had at that time was that the Bond grindability test at 48-mesh gave 6.04 g of undersize per revolution. A later test on the same sample at 100-mesh reduced this to 2.04 g, which is definitely in the harder ore class, and which makes the reported 8.80 kw-hr per ton of —200-mesh produced a very creditable figure. Hydroscillator Operation The machine as now developed has proved dependable and easy to operate. It starts easily under full load and responds quickly to operating adjustments. The hydraulic holes in the oscillating plate do not plug when shut down under full load. Absolutely clean hydraulic water is essential. An Elliott water screen or similar device should be an essential part of the machine to keep all scale and trash of all kinds from the hydraulic compartment. The shift operators have expressed approval of the machine. In table I we show a typical screen analysis of the hydroscillator rake sand as compared to conventional classifier rake sand on our ore. We have previously reported that of the 28.7 pct reduction in power, the hydroscillator contributed 6 pct, on a —200-mesh basis. This is a conservative figure. Some of our test runs indicated that the saving was as high as 10 pct. Laboratory studies by the Dorr Co. engineers indicate that still greater efficiency is possible. Nevertheless, the 10-ft plate is overflowing 2100 tons per day at 3 to 4 pct + 65-mesh, which is a very creditable performance by

Jan 1, 1951