Search Documents

By Christian Roche

Our study is focused on the sub-assembly con-tact shoes, pressure rings and pressure bellows. We were keen to mainly study [ ] 1.The contact shoe design 2.The most efficient pressure to ensure an optimal electrical contact between the contact pad itself and the casing 3. The contact shoe cooling circuit in view to provide to the shoe the best mechanical and electrical characteristics in order to bring to the users of COFOR® components a new standard in process setting technical solutions. A finite elements simulation, combined with a thermal and structural studies were used. Our presentation which follows is dedicated exclusively on the influence of the contact shoe cooling system on the process through a thermal and structural analysis. [ ]

Jan 1, 2007

By P. T. Brooks

Mineral nodules from the ocean floor represent a vast potential source of manganese, nickel, cobalt, and copper. Process development studies to devise methods for recovering these metals were conducted by the Bureau of Mines using two types of nodules--relatively low-grade calcareous nodules from the Atlantic Ocean and higher grade siliceous nodules from the Pacific Ocean. Ammoniacal carbonate leaching of reduced nodules appeared to have the best potential for processing the calcareous nodules, but the method proved to be impractical for recovering manganese. Extraction of 90 percent or better of the nickel, cobalt, and copper showed the technique to be attractive for recovery of these metals. The siliceous nodules appeared amenable to a process that starts with either a sulfur dioxide leach or a sulfation roast followed by a water leach to dissolve the soluble sulfates.

Jan 1, 1971

By Sam G. Demou

Drag bit cutting tests were conducted chiefly to determine bit forces encountered in rock types representing a range of compressive strength and hardness and thus enable the design engineer to estimate a continuous miner's performance in a range of rock types. Testing was carried out on the Bureau of Mines uniquely designed, instrumented rock cutting device (RCD). This device can make 3-ft-long cuts at various depths and speeds to approximate full-scale drag bit cutting by continuous miners. Point attack and cutter bits were tested on four rock types ranging in compressive strength from 7,200 psi (trona) to 29,600 psi (Valders white rock). Cutting tests were made at depths up to 1 in and speeds up to 70 in/sec. Data included normal and cutting forces, groove depth, groove width, and weight of rock broken. The effect of varying the cutting speed was determined, and specific energies were calculated for the various conditions. The bit wear was also observed. For the rocks tested, compressive strength and hardness are good indicators of forces, specific energy, and wear encountered. Results, especially bit wear observations, show the possibility of extending continuous miners, already being used in trona, to Indiana limestone (10,000 psi). Rapid bit deterioration precludes use in Tennessee marble (16,800 psi) and Valders white rock (29,600 psi).

Jan 1, 1983

By J. J. Forbes

Investigations by the Bureau of Mines and by mining-research departments of European countries have established definitely the value of rock-dusting to prevent or limit the propagation of coal-mine explosions. Its effectiveness in this connection has been demonstrated not only by research but by actual coal-mine explosions in which hundreds of lives have been saved because of its presence. In a general way this paper gives pertinent facts concerning rock dusting practices in the United States. Information has been obtained from many reliable sources, and various coal-mining companies have furnished data on cost and other details.

Jan 1, 1939

By G. L. Smith

Central to the success of any mining company is the ability to manage capital investment effectively so as to ensure acceptable stakeholder returns within an overall strategic context. Critical to this process is the effective selection and implementation of a strategically aligned project portfolio that enables optimal resource exploitation while operating within mandated bounds and identified constraints. Consideration is given to the strategic long-term planning process, an investment prioritization methodology and specific tools and techniques based on the discounted cash flow philosophy.

Jan 1, 2007

By K. J. Liles

The Bureau of Mines conducted laboratory semicontinuous and continuous heavy liquid tests to determine the feasibility of producing commercial-grade products from the high-clay sylvinite ores of the Permian Basin in New Mexico. Continuous test operations demonstrated that concentrates containing 59.9 percent K2O and recoveries of over 75 percent of the contained potash can be obtained. The organic heavy liquid was effectively recovered by vaporization, condensation, and absorption methods. Less than 5 parts per million of heavy liquid vapors were released to the atmosphere. This loss represents only 0.02 pound of heavy liquid per ton of ore treated.

Jan 1, 1973

The Round Hill gold-scheelite deposit is located three kilometres from Macraes Flat and approximately 60 kilometres due north of Dunedin, New Zealand. A mining feasibility study is currently being undertaken on the deposit by BHP Minerals (New Zealand) Limited, who are the managers and operators of a Joint Venture with Home Reef Mining Limited. BHP has a 70 per cent equity in the project area.

Jan 1, 1987

By H. L. Riley

Cleaning and handling of fine coal are generally conceded to be more difficult problems than preparation of the coarser sizes. Increased mechanization in the coal-mining industry has, in general, resulted in an increased percentage of the fine sizes in the total coal mined. If the coal fines are cleaned by wet methods, the minus-1/16-inch square-mesh particles cause most of the sludge and slurry problems encountered in preparing wet coal. Equipment that separates coal from refuse on the basis of specific gravity is not efficient on sizes that, because of their fineness, do not follow the same laws of hindered settling as the larger particles. Probably the best solution of fine-coal cleaning problems is to use other methods, such as flotation, that utilize other physical characteristics than those determining hindered-settling ratios. Regarding the type of flotation known as the Elmore vacuum-flotation process there has been a scarcity of data and information available in this country. An investigation has therefore been made to obtain additional date and information on this process under laboratory conditions. During this investigation an effort has been made to evaluate the relative efficiencies of vacuum and mechanical laboratory froth flotation cells. The investigation included float-and-sink, screen-sizing, and flotation tests on 2 different samples of 14-mesh to 0 raw coal and an a sample of slurry from the settling-tank overflow of a typical washer. One raw-coal sample was obtained from the American bed and represented a type of coal that is relatively easy to clean. The other raw-coal sample was from the Mary lee bed and represented a type considered difficult to clean.

Jan 1, 1954

By M. A. Leosson, S. H. Bottrell, R. J. Newton

Sylvite at Boulby is mined 1 140 m beneath the sea and the mine suffers from the influx of water. This is of two kinds: persistent flows originating in the Sherwood Sandstone aquifer and entering the evaporite sequence through fractures in the intervening mudstone, and impersistent flows which are transient in nature and of uncertain origin. Water from the overlying sandstone has become enriched with NaCl and large amounts of KCl and some Mg and Br have been added by interaction with the evaporites. Waters from the transient flows are isotopically distinct from those in the Sherwood Sandstone, being enriched in H and O. They are also saturated with respect to halite and sylvite, but have higher K/Na than the persistent flows and are much more enriched in Mg and Br

Jun 18, 1905

By Thomas E. Howard

Man has been engaged in the construction of tunnels in. rock for several thousand years. During that time, methods of tunneling have changed drastically. Hordes of men chipping away at the tunnel face have been replaced by mechanical drills and explosives and by tunnel boring machines. Spoil is no longer carried on the backs of humans, but is now removed by trains, trucks or conveyor systems. These and other changes have had the effect of greatly increasing the rate of tunneling, while at the same time, greatly decreasing the potential dangers to workmen. Although the techniques, equipment and material used for tunneling are being continually improved, rock tunneling is still a slow and expensive process. Significant improvements and innovations are needed to reduce the cost and time required for tunneling if we are to fully utilize the subsurface to aid in the solution of urban problems and in the conservation of resources. This report is intended to facilitate the orderly development of tunneling technology by focusing attention on the inadequacies of rock tunneling and the improvements that are needed. The data presented were derived from the results of a comprehensive questionnaire that was completed during the summer of 1969 by more than 600 individuals and organizations in 17 countries. Table 1 lists the countries and the number of replies from each. Appendix A contains a summary profile of the national responses, while the text presents the results and a brief analysis of the conclusions that might be derived from the data in the questionnaire. The data shown in Appendix A represent the consensus opinion of each of the 17 nations without regard to the number of individual replies or the amount of tunneling activity that is represented. The national consensus was determined for each country by a plurality of the individual responses, in some cases modified by the opinion of the rapporteur. Tire above procedures can lead to situations which are misleading. For example, experience and activity arc a rational basis for analysis; but, if national replies are weighted on this basis (i.e., number of responses), informed and valuable opinion of less active countries would probably be overwhelmed and lost. In analysing the data on the basis of national responses without weighting, it becomes apparent that many of the same problems exist under a given set of conditions regardless of the number of tunnels that have been driven.

Jan 1, 1970

By Germán Mallén

Como parte de los estudios línea base realizados por MWH Perú S.A. para el proyecto aurífero Chucapaca de las Canteras del Hallazgo en el distrito de Ichuña de la región Moquegua, Perú, se investigó el origen de boro, alta salinidad y otros componentes que perjudican la aptitud de los ríos Ichuña y Tambo para irrigación y otros usos. En este sentido, se encontró que la calidad de agua es perjudicada principalmente por altas concentraciones de sodio, entre otros, precipitándose como hidróxidos de estos metales debido al pH neutro en el río. En ese sentido, el presente texto describe la relación de este impacto químico con los manantiales entre el Cerro Chucapaca y el cañón del Río Ichuña/ Alto Tambo, ubicados al Norte de Moquegua, donde presentan la característica distribución de diferentes tipos de aguas volcanogénicas sobre un sistema de convección hidrotermal de agua meteórica profunda reciclada, calentada y movida por una cámara magmática andesítica que aporta calor y gases.

Sep 21, 2013

By Peter F. Weiss, H. Riedler, I. M. Moschitz, A. Olsacher, G. B. Fettweis

CONTENTS : 1. NATURAL FACTORS Geology Petrography and Rock Mechanics Mining System Orientation Rock Bolting System Movability of the Ore Grain Size Distribution Permeability Contamination Value of the Ore Hydrology 2. TECHNICAL FACTORS Height Length and Width Drawing Areas Time Factor Water Predrainage Surf ace Draining Underground Draining Advancing Slitting Sequence of Development Initiation of the Caving Process Drawing Rate 3. SPECIFIC MINING RULES Advancing Development Drawing Rate Interruption of Drawing (Water Distribution, Concentration of Mud, Dilution) Blasting 4. CONTROLS Safety Controls for Operation Computerised Drawing Control Structure of the Computer Program Hard Ware Print Outs 5. SUMMARY 6. ACKNOWLEDGEMENTS 7. REFERENCES Under the heading "Development System for Block Caving under Severe Conditions" a report was presented to this congress regarding a magnesite mine using block caving for several years. On account of the experience gathered in this mine and the results of far reaching exchange of experience, as well as under due consideration of the international literature it is tried to systematically list and briefly discuss the following factors that have to be considered for development and draw control of block caving. 1. NATURAL FACTORS It is self evident that this implies all those circumstances given by nature and which cannot be altered by man. Any mining activity is subjected to those and the success is depending on how far technology can be adjusted to those conditions. Geology Deposits of considerable thickness with rather steeply inclined flat-faced contacts are optimal for block caving. While vertically there is practically no limitation- for the deposit, theoretically, the smallest horizontal basis apt for operating block caving is the minimum area necessary to get the rock to completely cave in by undercutting and drawing. Practically, only consider- ably bigger main dimensions are found, mainly because of technical factors (machinery and equipment) and economic factors (cost ratio of exploration vs. development, danger of contamination).

Jan 1, 1981

By F. M. Makarinsky

"SynopsisThe Kanichee open pit mine and milling complex is situated approximately four air miles north-west of Ternagami, Northern Ontario, in Strathy Township. Mining and milling production commenced in January 1974.Milling throughput currently is at a rated capacity of 500 tons per day, seven days per week. A bulk nickel-copper sulphide concentrate is produced, and is trucked daily to the smelter at Falconbridge Nickel Mines Limited, Falconbridge, Ontario, some 120 road miles from Kanichee. Concentrate grades produced are in the order of 4.0% Ni and 8.0% Cu, with corresponding recoveries of 68-70% nickel and 86-90% copper. Stage additions of 100% guar-gurn solution reagent to the flotation cells for depression of talcose minerals, proved to be the major break-through for optimizing metallurgical performance.2. HistoryThe present Kanichee Mining property is known to old-timers in the Temagami area as the former Cuniptau Mine. Several attempts were made in the mid '30's and 40's to extract the ore at a profit, but each effort resulted in failure.In 1933-36, Cuniptau Mines Development Co. Limited, later called Cuniptau Mines Limited, sank a 245-foot vertical shaft and completed 2,200 feet of lateral work on the 100-140 and the 225 foot levels. Fifteen tons of ore were sent for testwork to the Mines Branch, Ottawa, Ontario.Cuniptau Mines Limited, in 1936, milled some 3,000 tons, and the resulting concentrate was put through a pilot smelter situated on the present mine site. Metallurgically, the smelting results were not encouraging, primarily due to the high melting point of the talcose minerals in the concentrate. From the period 1937-48, minor exploration work was done by Ontario Mining Corporation, Ontario Nickel Mines Limited, and Trebor Mines Limited. During the period 1948-49, 128 diamond drill holes, totalling 40,900 feet were evaluated by Trebor Mines Limited. In 1961, the name was changed to Ajax Minerals Limited, during 1968, five diamond drill holes were sunk, totalling 1,700 feet. Since that period the property has remained idle."

Jan 1, 1975

By Don Novotny, Dana Spencer

In this workshop our intent is quite simple; that is that we will introduce a relatively new technology that may have applications in blasting applications. This technology is the laser initiation of explosives. This workshop course is not intended to suggest ways in which specific blasting problems can be resolved. That is the purview of experts within each of your fields.

Jan 1, 1994

By Richard Hosley, James Daley

Every grey haired member of the explosive’s industry has said at least once, “We have to get some younger blood into our industry, I might want to retire someday.” And many a youngster who loves to see explosions has wondered how to get involved in such an exciting, yet intimidating, industry. While there are many answers to these questions, an internship program is a great answer to both

Jan 1, 2014

By Wilbur I. Duvall

In a review of so 40 papers on damage to residential structures resulting from blasting, only 3 were found that present data on the observed amplitude and frequency of the vibration levels produced by blasting together with an observed degree of damage to a residential structure. The data from these three reports have been analyzed statistically to determine if one of the quantities, displacement, velocity, or acceleration, is more reliable than the others for estimating the degree of damage to a residential structure. From this analysis the conclusion is drawn that a given degree of damage to a structure is most closely related to the magnitude of the particle velocity of the wave motion passing thru the earth at the structure location. On the average, only minor damage it observed for peak particle velocities of 5.4 inches per second, and major damage is observed for peak particle velocities of 7.6 inches per second. When the spread of the data is taken into consideration, the following statement can be made: Wave motions that have a peak particle velocity in excess of 2 inches per second have a fair probability of producing some damage to structures, whereas wave motions that have a peak velocity less than 2 inches per second have a very low probability of causing any damage. Therefore, the recommendation is made that vibration levels in the vicinity of residential structures should be maintained below a peat particle velocity of 2 inches per second. The above criterion for safe blasting is considered to hold over a wide variety of soil and rock conditions because the original data were obtained for a wide range of soil and rock conditions and on various types of residential structures. INTRODUCTION Ever since explosives were discovered and developed for mining purposes, there has existed the problem of what effects the air and ground vibrations resulting from blasting have on structures of various types. This problem is

Jan 1, 1962

By B. J. Moore

This publication contains analyses and related source data for 310 natural gas samples from wells and pipelines in 16 States. All of the samples were obtained and analyzed during calendar year 1978 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis appara¬tus, which are described in Bureau of Mines Bulletins 4862/ and 576.3/ The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the public in general. Twenty previous publications have presented the results of 11,573 gas analyses made prior to 197R. The first three, Bulletins 486,4/ 576,5/ and 617,6/ contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other 17

Jan 1, 1979

Introduction The Homestake Mining Co. has always been big on gold. After 108 years in the business, the company and its principal product are almost synonymous. The relationship continues. On Sept. 28, 1985, Homestake held formal dedication ceremonies for its newest gold mine - McLaughlin. The McLaughlin open-pit operation is located in northern California, some 113 km (70 miles) northeast of San Francisco. It lies near the boundaries of three counties - Napa, Yolo, and Lake - and a portion of its facilities are located in each. McLaughlin was originally the site of the Manhattan mercury mine that produced nearly 80,000 flasks of the quicksilver from the 1860s to 1978. At the September dedication, Homestake renamed the mine in honor of the late Donald H. McLaughlin. McLaughlin was with Homestake for nearly 60 years. He rose from exploration geologist to his ultimate positions of chief executive officer, director, chairman of the board of directors, chairman emeritus, and chairman of the executive committee. The discovery of the McLaughlin deposit occurred in 1978, the last year of operation for the Manhattan mine. Homestake geologists used a newly developed model and found surface gold at the mine site. That same year, Homestake signed an agreement with the property owner and began a two-and-a-half year exploration program. An initial discovery announcement of 31.1 t (1 million oz) of gold was made in 1980. In 1981, this was revised to 93.3 t (3 million oz), or 18 Mt (20 million st) of ore grading 5.2 g/t (0.152 oz per st). Expected mine life is 20 years. Construction began in September 1983, following the issuance of stage one permits. Start-up of operations took place in early 1985 and the first gold-silver dore bar was poured on March 4. Since then, more than 540 kt (600,000 st) of ore has been milled, producing about 1.6 t (50,000 oz) of gold. Of special interest at McLaughlin is the use of three autoclaves for gold extraction. According to Homestake, this is a first. The autoclaves are designed for a 90% gold recovery rate. Early results have proven yields at this rate and higher. Geology The McLaughlin deposit is about 1.5 km (5000 ft) long. It occurs as a wedge-shape, narrowing to a verti-

Jan 1, 1986

By A. Ochieng

Solids suspension influences the quality of mixing and energy requirement in a solid-liquid system, both of which determine the efficiency of industrial processes such as nickel precipitation. Nickel solids concentration distribution in a stirred tank was investigated using computational fluid dynamics (CFD) and experimental methods. The concentration distribution of the nickel solids was compared with that of sand and glass. The laser Doppler velocimetry (LDV) method was used to measure the velocity field for the liquid-only system and an optical technique was employed to determine the axial solids concentration distribution. Regions of in homogeneity in the tank were identified. It was found that, for a given solids loading, the solids concentration distribution depended on both particle size and particle size distribution. High solids loadings were investigated and a difference in the concentration distribution pattern was obtained with nickel, flint glass and sand particles. The CFD simulation results highlighted problems that could be associated with some conventional experimental methods of determining solids concentration distribution in a stirred tank. Keywords: nickel; CFD; simulation; mixing; solids suspension.

Jan 1, 2010

By E. Fahrenkrog, D. Sbartaro, E. N. Cifuentes

An intelligent supervisor using expert system tools and applied to a crushing plant has been developed with a structure based on a model of a human operator. It consists of a knowledge base containing a qualitative model of the process and a rules base with the heuristic logic used by an operator when supervising a plant. The simulation results obtained show the potential of this type of system to supervise the automatic operation of a plant. There has been very significant development in artificial intelligence over the last two decades. Within this development, two approaches can be distinguished, (Winston, 1984). The "model approach," in which the main objective is to understand and model the be¬havior of living systems. The second approach is the "engineering approach." Here, systems capable of performing tasks usually requiring human intelligence are created. As part of this latter approach, knowledge engineering and its main achievement, expert systems, have been developed. Expert systems arose from the need to incorporate the abilities of a human expert in solving realistic problems in which the conventional approach has great difficulties. The first successful applications of expert systems were in medical diagnosis, geophysics, and fault detection. However, since 1971, when Fu (1971; defined intelligent control as the inter action of artificial intelligence and automatic control, some significant developments in the use of artificial intelligence tools for process control have been achieved (Astrom, 1986; Pinto 1988; Fahrenkrog, 1988; and Porter 1987). The modern control theory has made important advances. And, although successful in some applications, it has failed to cope with the practicalities of many industrial processes. As a result, the automatic operation of a plant has been confined to a small region around a normal operating point and to periods without any great disturbance. One of the main reasons for this is the lack of accurate and structured knowledge of the processes involved. Despite this, operators applying their knowledge, experience, and a little intuition, often obtain good results controlling the plant in such situations. Considering the above, the next obvious step is to include similar reasoning capacities in a computational system. The development of such an expert supervisory system prototype applied to a mineral crushing plant is presented. Problem description The problem is to conceive a control system with the ability to handle quali-

Jan 1, 1989