Search Documents

By Hamid Maleki

Prudent design of coal pillars in any mining system requires an estimation of in-situ pillar strength, overburden lateral load transfer capability, and a failure criterion. Pillar strength is typically determined using one of several different empirical pillar strength formulas. For coal reserves in the U.S., a new pillar design method was proposed based on extensive U.S. field measurements in underground mines (7) which accounted for confinement effects. Field measurements in seven U.S. seams indicated highest strength for some Utah mines where the coal seam developed high confining stresses. Lower strength was measured in structurally controlled seams. This method is expanded here including the data from the weaker tertiary coal measure rocks and lower confinement for pillars with low width-to-height ratios. The determination of how much load a pillar is expected to take is partially dependent on the ability of overburden to transfer load laterally; this is useful for selection of panel width and barrier pillars size in select mining applications where long-term stability is required in conservative designs. In caving mining systems, caving of the strata is influenced by geologic, mining and stress conditions and the released energies influences how the pillars react at loads approaching pillar strengths. Overburden deformation and caving mechanisms are analyzed in this paper in multi-panel extractions to enhance the understanding of load transfer, seismicity and coal bump control in deep western U.S. operations.

Jan 1, 2008

By Donald W. Breck

Zeolites were first recognized as a new group of minerals by Cronstedt with the discovery of stilbite in 1756. The word zeolite was coined from the two Greek words meaning "to boil" and "a stone" because of the loss of water when heated in the mineralogist's blow pipe. (1) In 1845 it was discovered that certain soils have the power of retaining ammonium Salts. (2) These were the first ion exchange experiments. Later it was discovered that it was the hydrated silicates in the soil that produced this phenomenon and several years later a paper was published dealing with the action of dilute salt solutions on silicates which showed that this base exchange principal, which we now call cation exchange, is reversible. The quantitative cation exchange behavior of zeolite minerals, such as chabazite, was studied. As a result any aluminosilicate which exhibited the property of ion exchange was referred to as a "zeolite;" even today the term has been applied to clay minerals as well as synthetic organic ion exchange resins.

Jan 1, 1973

By A. F. Marques

The Azores islands are located on a triple junction where the American, African (AFR), and Euroasian (EUR) plates meet. The Mid-Atlantic Ridge (MAR), oriented N-S, represents two branches of the T; an E-W branch defines the EUR/AFR boundary called the Terceira Rift. The nature and structure of this plate boundary, as well as the dynamics of the interaction of tectonics and volcanism remain unconstrained. The Azores plateau is seated on a mantle domain of anomalously low seismic S-wave velocities, and gravity and geoid anomalies, where the apparent thick crust is thought to relate to larger degrees of melting initiated at greater depths [1]. The cause of these anomalies is controversial but many authors consider the presence of an anomalously hot/wet enriched mantle probably supplied by a plume [2]. The geochemistry of the subaerial and most submarine lavas from the plateau reinforces the plume model beneath the Azores [3-4]. The origin, size and present location of the plume is under debate but an area near Terceira is the favoured plume centre [5]. [ ] SEAFLOOR HYDROTHERMAL SYSTEMS IN THE AZORES AREA (36ºN ? 40ºN) More than 150 active and fossil hydrothermal systems are known in the oceanic seafloor [6]. Many more are yet to be found on vast oceanic areas that haven?t been explored [7]. Ever increasing knowledge shows that modern seafloor hydrothermal systems can be hosted in felsic to ultramafic rocks, vary in size and shape and exhibit diverse amounts of sediment cover

Jan 1, 2011

By William L. Young

There is an old saying in Canada: "Mines are made as much as discovered." What follows is Young's perception of his experience developing and financing the Cochrane Hill gold mine project. In 1974, I came back from rutile and zircon exploration and mining in Australia. I became interested in a copper, lead, and zinc project in the Bathurst District, New Brunswick. Much field work had already been done but I was convinced that a reinterpretation of the geophysical work left room to enlarge on the known mineralization. So, with my own money I put a property deal together, found an underwriter willing to raise $100,000, and had a lawyer produce a prospectus. The prospectus was ultimately accepted for filing by the Ontario Securities Commission and I acquired funding and began work. It did not take many drill holes to determine that the interpretation was not geologically valid. However, while drilling was going on, geophysical and geochemical explorations indicated interesting anomalous zones elsewhere on the property. But by now the base metal market climate had soured and the $50,000 I had left was not enough to evaluate the new results. So I decided to farm out the property. A data folio was produced and the property was optioned to a major mining company, with Northumberland Mines Ltd. retaining a 20% free, carried interest. By 1976, the market for junior issues was so bad no under¬writer would even talk to a geologist and I still had the $50,000 in the bank and was looking for something to initiate. A Project That Went Nowhere Market research indicated that the Toronto area imported fine calcium carbonate fillers from Georgia, Alabama, and Vermont. I was aware of the specs and the fact that there is a large marble belt in Eastern Ontario. After some prospecting, I found an interesting deposit. The product was slightly high in silica and low on brightness. Research work eliminated the silica and corrected the brightness. So, with insufficient money we launched a feasibility study. This included diamond drilling, bulk sampling, special fine grinding and air classification tests, and an in-depth market survey. Our product was as good or better than those on the market. Our advantage was that delivery could be made by a two-hour truck haul to the customer. The present system of rail delivery had many problems, especially in winter. Despite everything looking rosy, we ran into a stone wall. The underwriters were singularly unimpressed because the public saw little glamour in a substance most people had never heard of. The issue would have been difficult-if not impossible-to sell. Banks and government agencies took the position that if we could get long term take-or-pay contracts then they would lend the required capital. None of the suppliers, however, would even consider a contract until production had begun and they could evaluate the production material. It was a classic "catch 22" situation. I have gone into this in some detail to show how tough the industrial mineral market can be. We eventually optioned this calcium carbonate property to a major corporation. The option agreement would give us a free, carried 15% and the right to buy up to 40% for contributing 25% of the production costs. But the experience left my company in poor financial shape. To survive, I think the entrepreneur-geologist must always have at least one project in reserve, an emergency plan. I had been searching out a new project to work on, after the calcium carbonate option was wrapped up. It was gold. Gold intrigued me and I knew quite a bit about Nova Scotian gold. I felt that with any rise in price, many of the former high-grade gold mines would have interesting potential for the larger, low grade portions of the deposits. That is how I happened on Cochrane Hill, where much work had been done in the early 1970s when gold as $4.82/g ($150/ oz). This time my timing was good. No sooner had Northumberland signed an option agreement than gold prices started to rise. In six months, they went to $27.331g ($850/oz). Even so, financing gold prospects in early 1980 was still not easy. It had been years since gold financing had been undertaken. A whole new generation of investors, with no knowledge of gold mining, had grown up. So, with accounting and legal council, we decided on a semiprivate "seed money" offering. Under the new Ontario Securities Act, this was a new-and partly tax sheltered-concept. At the time, it was very innovative.

Jan 6, 1982

By F. E. ROGERS

CUSHMAN TUNNEL No. 2 is adjacent to the Hood Canal, near potlatch, Wash. It is 17 ft. inside .diameter, about 13,000 ft., or two and one- half, miles in length, and is a part of the second unit of the Cushman power project. It connects Cushman ' Dam No. 2 and the penstocks that lead to the power house on the beach about 400 ft. vertically below the outlet of the tunnel. One shaft, 190 ft. deep, and two adits between 300 and 400 ft. long, were provided to speed up driving operations. his arrangement gave 6 working headings, which were operated 24 hr. daily. The shaft provided a manway, cageway, and skipway.

Jan 1, 1931

By Kenneth Pidgeon

The Boston Marine Industrial Park (BMIP) Boat Section, which is part of contract C04A2 of the Central Artery/Tunnel (CA/T) project, is currently under construction in South Boston, Massachusetts (Fig. 1). The Boat Section is approximately 900 feet long and varies in width from about 135 to 185 feet (Fig. 2). The depth to the top of the Boat Section base slab varies from about 28 to 31 feet below final ground surface and about 23 to 26 feet below normal ground water levels. The Boat Section is supported on 578 anchors drilled into the underlying bedrock each designed for a working load of 630 kips. Design and Construction Team The owner of the project is the Massachusetts Highway Department (MHD). The owner's representative is the Management Consultant, Bechtel/Parsons Brinckerhoff. The section design consultant (SDC) consisted of HDR Engineering, Inc. with GEI Consultants, Inc. as the geotechnical subconsultant. The general contractor was the joint venture of Kiewit, Perini, Atkinson, and Cashman. The boat anchors were installed by the subcontractor Delta Geotechnical Services, Inc.

Jan 1, 1994

By Iara Patricia Vieira de Oliveira

O coque desempenha três principais funções no Alto-Forno sendo elas: física, térmica e química, em se tratando do papel físico, a função estrutural é de primordial importância, pois não pode ser assumida por outro combustível, com isto as indústrias avaliam a resistência mecânica a frio para garantir uma marcha estável no reator, porém os ensaios padronizados não são suficientes para avaliar a resistência do coque. Neste contexto este trabalho desenvolveu uma metodologia para avaliar de forma individual a resistência mecânica a compressão do coque nas granulometrias típicas do coque metalúrgico e como os principais defeitos, poros e trincas governam a resistência do material. Foram realizados testes de compressão, análise de microestrutura, microtextura, inspeção visual de trincas, MEV. Os resultados das análises realizadas no coque mostraram que a tensão média de ruptura aumenta com o aumento da granulometria.

Oct 30, 2017

By Catherine T. Ziten

Introduction ?Environmental assessments required for permitting ?Focus on ammonia produced through mine construction & blasting ?Water quality guidelines: federal, provincial, IGO ?Reported values are typically estimates from other projects ?Predictive modelling of ammonia aimed to assist planning

May 1, 2009

By Bill Mariucci, Gary Almeraris

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2009

By Alan K. Burton

Massive increases in the productive capability of open pit nines after World. War II were in a large part made possible by the introduction of ever larger trucks and the supply of a seemingly bottomless ocean of inexpensive and readily accessible oil. Over a period of about 25 years, a variety of technological developments permitted a tenfold truck payload increase, from about 32 tonnes (35 tons) to 320 tonnes (350 tons). There is no, doubt that this was a remarkable achievement resulting in impressive benefits of scale as well as the ability to control what would otherwise have become an intolerable traffic congestion problem in today's large open pit mines. It became fashionable and economically possible during this time to mine large quantities of low grade material and to tolerate very high stripping ratios. As tine has gone by and as easier to get at and higher grade deposits have been depleted, ore grades have tended to decline while stripping ratios have increased. The alternative to reduced revenues has been an ever increasing demand to step up production which in turn has led to a continuing demand for ever larger and larger trucks. While a larger truck has had the effect of reducing the cost of the operator per unit of material moved and of reducing traffic congestion, it has not specifically addressed the subject of fuel cost.

Jan 1, 1981

By Byron S. Kutscher

This report summarizes the program to develop and construct an improved light-scattering dust monitor (ILSDM). This improved light-scattering dust monitor, which operates on the forward light scattering principle, provides instantaneous measurements of airborne dust concentrations in units of mg/m. The program was divided into two phases. Phase I involved the design of the ILSDM which was reviewed by the Bureau of Mines. Phase II included the fabrication of a prototype ILSDM based upon the design developed during Phase I. After completion, the ILSDM was delivered and demonstrated at the Bureau of Mines. A description of the final ILSDM design, operating instructions, maintenance instructions and recommendations for additional work are also included in this report.

Jan 1, 1980

By Paul M. Godlewski, Joseph P. Gildner, David S. McAllister

With construction underway on the 22.5 km (14 mile) Initial Segment of the Link Light Rail transit system in Seattle (including the one-mile EPB-driven running tunnels and mined station at Beacon Hill), the Sound Transit Board on May 20, 2004 voted on selection of a preferred route for an approximately eight-mile extension northwards from the central business district to Northgate, and authorized immediate start of advanced conceptual/preliminary engineering and geotechnical exploration programs scheduled to be completed in Spring 2005. The extension includes approximately914 m (30,000) route-feet of bored running tunnels, a mined station with platform level approximately 60 m (200 ft) below grade, three (possibly four) cut-and-cover stations and a cut-and-cover cross-over structure, as well as an aerial terminal station at Northgate and other line-section below-grade and aerial structures. All tunneling will be in glacial soils.

Jan 1, 2005

The accompanying supply/demand flow diagrams and 10-year tables for mineral and fuel commodities present essential data required by government, industry, and others to formulate policies and programs that can help assure an adequate and continuing supply of mineral raw materials. The 10-year data base terminates with 1975 figures because adequate world information was not available beyond that date. The selected mineral supply/demand tables and flow diagrams comprise but one "output" from the massive body of information and data collected and compiled by the Bureau of Mines on a continuing basis covering mineral production, consumption, prices, shipments, imports, exports, and stocks, as well as industry activities in all States and abroad.

Jan 1, 2012

By AIME AIME

WAR undoubtedly accelerates metallurgical progress, although its most obvious effect is a tremendous waste of materials. The necessity for restrictions in normal uses of metals results in a search for substitutes or for enhanced properties that will make a limited supply last longer. An insatiable demand for more metal to be produced more quickly favors trial of new processes, new metallurgical tools, and new methods of fabrication. Greatest advance is made, of course, in practical physical and process metallurgy. Theoretical or fundamental research necessarily must take a secondary position, and is so regarded in this review. It is not that developments in theoretical physical metallurgy are lacking entirely, but, following the same trend noted in other countries as they entered war activities, attention in the U.S.A. has been shifted strongly to those developments having an immediate practical application.

Jan 1, 1943

The U.S. economy continued to expand during 1986, although at the slowest pace since 1982 when the current business expansion began. Real gross national product (GNP) grew about 2.6%, slightly below 1985 growth but significantly below that of 1984. The continuing expansion was fueled pre-dominantly by rising personal consumption expenditures as well as growing Government purchases of goods and services. Fixed investment, although positive, failed to grow at the rate of the overall economy. The trade deficit, which increased more than 30% over the record 1985 level, continued to depress economic growth despite significant declines in the price of petroleum and the value of the dollar. On a more positive note, domestic employment continued to grow--increasing over 2 million from the 1985 level--and inflation and interest rates declined. The unemployment rate dropped slightly to 7.0%. Of direct importance to the mineral-producing industries, expenditures for consumer and producer durables as well as investment in residential construction each grew faster than the overall economy, but investment in nonresidential structures fell more than 10% from the 1985 level. The level of real capital spending declined about 3% in 1986, following strong gains in 1985 and in 1984. Capital expenditures for new plant and equipment bottomed out in the second quarter and expanded in the third and fourth quarters. The decline in the first half of the year was partially attributed to uncertainty arising from the then-proposed tax bill. Also, there was little impetus for corporations to invest in new capacity since factories were operating at less than 80% of capacity during most of the year, in part because of continued competition from imports.

Jan 1, 1986

1. Domestic Production and Use: In 1984, 12 companies operated 27 primary aluminum reduction plants, with 3 firms accounting for 57% of production. Washington, Oregon, and Montana accounted for 35% of the production; Indiana, Kentucky, Missouri, and Tennessee 25%; Alabama, Arkansas, Texas, South Carolina, and North Carolina 20%; other States 20%. Based on published producer prices, output of primary metal in 1984 was valued at $7.2 billion. Aluminum consumption by 25,000 firms was centered in the east-central United States. Packaging accounted for an estimated 35% of domestic consumption in 1984, transportation, 20%; building, 18%; electrical, 9%; consumer durables, 8%; and other uses, 10%.

Jan 1, 1985

By Ke Yang

In Chinese coal mines, extraction of deep, highly gassy soft coal seams sandwiched between soft floor and soft roof in complicated geology is commonly encountered. How to safely and efficiently excavate such seams is a very significant and important problem. It has been a focused research area in recent years. By combining the characteristics of fully mechanized longwall mining methods such as large cutting height and mining along the dip, an integrated method and technologies for the Zhangji Coal Mine were developed. This technology includes the design of a complicated geological exploration system, optimization of mining method and working face parameters, control of rock pressure and high levels of gas, reliability model of the production system, and selection and compatibility of equipment. Engineering practice shows that the integrated technology was successful in mining these complicated seams. This study not only enriches the mining method, but also improves the coal mining practice, especially ensuring both safety and productivity under complicated geological conditions.

Jan 1, 2009

By R. A. McIvor, R. Levac

"The Stobie No. 7 shaft, 14 ft diameter, double- drum skip hoist, was installed at the INCO Limited Frood Stobie Complex in 1942. Figure 1 shows the hoist layout. The hoist was originally equipped with babbitted journal bearings on the main drum shaft and pinion gears. In 1990, the hoist was modernized with a new braking system, two new 2000 hp D.C. drive motors, a thyristor armature supply and a PLC control system. The new drive motors were connected to the drive pinion gears with a gear type flexible coupling. The pinion gear journal bearings were refitted during the refit in 1990 as the existing babbitted bearings showed signs of wear. The pinion gear journal bearings had always run warm and had external cooling applied during the warm summer months. Figure 2 shows the journal bearings on the pinion shaft. The skip hoist main bull gear and two pinion gears were replaced in 1997 because of cracked bull gear spokes. New drive couplings were installed on the pinion gears and the pinion journal bearings were modified to allow some self-aligning properties to try to reduce the heating and wear on the babbitt. The modifications did not significantly reduce the heating problems and a decision was made in the spring of 1998 to convert the bearings to self-aligning, anti-friction-type bearings.The traditional roller bearings used on double helical pinion drive gears in hoist applications has always been double-row spherical roller bearings due to their high load-carrying capacity and misalignment allowances.Unlike single helical gears, double helical arrangements do not exert axial thrust on the pinion gear bearings, therefore, both bearings in the pillow blocks must float easily with any pinion displacement. Drum misalignment, thrust bearing end play and a multitude of other influences causes continuous axial displacement of the pinions when in operation. This constant displacement or “hunting” of the pinion gear to maintain its centre on bull gear often exceeds the axial clearance limits of spherical roller bearings thus resulting in a continuous sliding motion of the bearing outer rings against the housing seats. With time, the housing fit eventually wears, creating an out-of-round condition for bearing housing (maximum allowable cylindricity tolerance is IT4/2). When this happens, the pillow block housings must be replaced or re-machined to specification. Premature bearing wear and overheating will occur if a housing out-of-round condition is encountered."

Jan 1, 2001

By Douglas W. Fuerstenau, Pradip Pradip

The design and development of selective flotation collectors has been the key to the remarkable success of flotation in beneficiating complex, difficult-to-process ores. Sustained research efforts in the field over the past hundred years have led to delineating the scientific basis of selective mineral flotation in terms of the crystal chemistry and the surface and colloid chemistry of minerals including their solubility, and the aqueous solution chemistry of added reagents. It is now well-established that the electrical double layer theory (EDL) is the most powerful means of quantifying the relative strength of mineral-reagent interactions in the case of nonsulfide minerals. We illustrate the utility and the power of the EDL in delineating the science underlying selective mineral flotation with the help of a few examples taken from our own work, in particular on the selective flotation of rare-earth minerals (bastnaesite) from associated semisoluble minerals (barite and calcite) using alkyl hydroxamate collectors and the flotation separation of lithium-containing minerals (spodumene) from associated alumino-silicate minerals with oleate (fatty acids). Both of these mineral separation systems are of contemporary research interest and of immense value to the industry today. Recent advances in utilizing molecular modeling computations, particularly in the context of quantifying the effect of crystal chemistry and the relative distribution of adsorption sites available on mineral cleavage planes, are also reviewed.

By D. Robert Weir, M. J. H. Ruscoe, R. M. Berezowsky, M. A. Clegg

The metallurgical processing involved in the produc-tion of the new Canadian one dollar coin is reviewed starting with the hydrometallurgical production of pure nickel powder, followed by the powder metallurgy process for the production of nickel strip and coinage blanks, and concluding with the Aureate bronze electroplating and heat treatment procedure. Coinage requirements are then reviewed with regard to economic, public acceptance, and service requirements. Finally the properties of Aureate nickel coinage are presented in the light of the many and varied coinage requirements, and it is concluded that the new Canadian dollar coin exceeds the requirements admirably.

Jan 1, 1990