Search Documents

By Manuel Caro

El presente trabajo describe el proceso de mantenimiento del equipo de aire denominado Optiair. Este filtro al tener una mayor capacidad de retención de polvo, permite que el equipo pueda trabajar por periodos más largos sin tener que detenerse para realizar el cambio de filtros, lo cual incrementa el factor de disponibilidad del equipo. Entre los beneficios principales tenemos: el incremento de salida de aire, menor restricción del flujo, menor caída de presión y una mayor cantidad de contaminante capturado.

Aug 25, 2002

By P. G. Pigott

The lack of technical information regarding the physical characteristics of kaolins and bauxitic kaolins, rejected during the mining of bauxite near Eufaula, Ala., has retarded their commercial utilization. This investigation was undertaken to determine their behavior when used in refractories. Ores were evaluated as refractory raw materials by compounding dry-press mixtures and specialties following procedures common to the industry. Products now on the market were used for comparison in laboratory evaluation.

Jan 1, 1959

By Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Mehmet Aksoy, Kagan Ozdemir, Adiguzel Deniz

This paper presents the results of ground vibration measurements induced by blasting during the construction of the Istanbul Kadiköy-Kartal metro tunnel which has been driven at a depth of approximately 20-40 m deep under a highly urbanized region of Istanbul city in Turkey. This tunnel is being constructed by a joint venture group. The formation encountered during the construction is classified as hard and strong rock by laboratory and field tests performed by the joint venture group. Within the scope of the study, for the prediction of the peak particle velocity and to determine the slope of the attenuation curves together with the maximum charge per delay for the S4 shaft tunnels and S12 shaft tunnels of this tunnel route, ground vibration components were measured carefully by using four vibration monitors (Instantel Minimate Plus model) during the advancement of the tunnels which required blasting. The particle velocities and frequency values of all blast events are evaluated according to the United States Bureau of Mines (USBM) and German DIN 4150 Norms in order to predict, and compare the influence grades to the neighbouring buildings, and structures. Also, data pairs of scaled distance and peak particle velocity obtained from 114 records at S4 shaft tunnels and 79 records at S12 shaft tunnels were analysed statistically. Empirical relationships with correlation at the 95 % confidence interval were established for different rock units (diabase and arkose) and suggested for the test sites in order to estimate particle velocity of the ground vibrations.

Jan 1, 2007

By H. P. Stüwe

HE recent papers of Aust and Rutter112 have again brought to mind the importance of certain "special" orientation relationships between the lattices of two fcc crystals on the mobility of the grain boundary separating them. No theoretical treatment of this problem has been offered till now. The only principle published so far that has given an indication why certain orientation relationships should be "special" is the counting of "coincidence sites" according to the suggestions by Kronberg and Wilson.3 The "coincidence plots" published by these authors show, for instance, that two fcc lattices rotated by 38 deg around a common (111)-axis have 1/7 of their lattice sites in common. Such an orientation relationship is also characteristic for high boundary mobility. The accuracy of the orientation relationship needed for high mobility is not too rigid. Deviations up to 10 deg from the ideal orientation seem to be tolerable as can be gathered from the experimental data.'j4 The auestion arises, then. how the density of coincidence sites will be affected by a deviatioi from mathematical accuracy. This can be checked by a simple model. Two sieves are prepared, the arrangement of the holes corresponding to lattice sites on a (111)-plane in a fcc crystal. They are placed upon each other, Fig. 1. One is kept fixed, the other is rotated around an axis pushed through one hole in common to both. The light falling through holes of both sieves is then a measure for the density of coincidence sites. If the diameter of the holes is very small, light intensity is contributed only by holes the centers of which coincide "exactly." If the diameter of the holes is rather large, some intensity will be contributed by

Jan 1, 1962

By Gary Friedline

As a consequence of the Coal Mine Health and Safety Act of 1969(PL91-173), the Bureau of Mines (BOM) entered into a contract with Ocean Energy Inc. (OEI) to develop, fabricate, install, and evaluate a permissible lighting system for use on a longwall coal mining operation. The program schedule is shown in Figure 1.1. The proposed regulations are contained in Appendix A. The initial part of the program involved a survey of existing longwall lighting practices in Germany and England and an evaluation of a variety of lighting components on a mockup of a longwall mining operation that was fabricated under this program. Visits made to German and British mines uncovered major differences in lighting level requirements, permissibility aspects, size, and operating constraints which identified wide disparities and essentially eliminated from further consideration any known imported lighting devices for meeting the higher lighting levels and standards proposed for US coal mines by the Mining Enforcement and Safety Administration (MESA). The longwall mockup provided use¬ful information regarding the amount of illumination required, physical size and shape of lamps, light distribution problems, cable routing, use of connectors, signaling, glare, and other important factors unique to the lighting of low coal longwalls.

Jan 1, 1975

By M. E. Rossi

In mineral resources, geologic and mining data are acquired, processed, analysed, interpreted and modelled, eventually serving as basis to generate predictions and production plans. This is a complex process, and the resulting predictions are impacted by uncertainties related to the data itself and the processing methods and techniques used. They are also impacted by the subjective decisions made by the modeler(s) at each step of the way. Knowledge, biases, skills, and prior experience come into play in the long mineral resource evaluation development workflow. It is meaningless to discuss uncertainties without evaluating the associated risks that those uncertainties imply. It is important to quantify and assess uncertainty, and to evaluate and mitigate its consequences. This paper discusses (1) conceptual and practical sources of uncertainty; (2) the utopia of an “objective” uncertainty; and (3) the quantification and public reporting of uncertainty using geostatistical conditional simulations. The objective of this paper is to postulate that the industry is running out of reasons and excuses to ignore uncertainty and risk in project evaluation. This is done in two parts, with this, the first one, presenting a more conceptual discussion. Part 2 will present case studies from different types of mining projects and operations showcasing the impact that risk assessments can have in a mining project.

Feb 22, 2026

By G. Norman Owen, Roger E. Scholl

INTRODUCTION The analysis and design of underground structures to resist vibratory motion due to earthquakes has been of interest to engineers for several decades. The dynamic stability of a powerhouse cavern was considered in the 1960s (Campbell and Dodd, 1967). About the same time, the designers of the San Francisco Bay Area Rapid Transit system developed procedures for analyzing the subaqueous tunnels placed under San Francisco Bay and the tunnels excavated along the land portions of the alignment (Kuesel, 1969). Japanese designers developed fairly sophisticated procedures for analyzing subaqueous tunnels during the late 1960s and early 1970s (Kuribayashi et al., 1974). In the past decade, proposals to site important critical underground facilities in regions with moderate to high seismic activity have increased the interest in earthquake engineering of underground structures. Seismic designs or seismic studies have been conducted for rock caverns for storage of petroleum or location of power plants (Yamahara et al., 1977; Glass, 1976), buried tanks for fuels or rad¬ioactive waste (Fukushima et al., 1977; URS/Blume, 1976), tunnels for disposal of nuclear waste (Yanev and Owen, 1978; Wahi et al., 1980), and urban mass transit tunnels (Monsees and Merrit, 1984). One of the greatest drivers of the interest in seismic analysis and design of underground structures has been the proposals to dispose of high-level nuclear waste in mined repositories some 300 to 600 m (approximately 1,000 to 2,000 ft) below the ground surface. In 1979, the authors, in conjunction with Professor Tor Brekke, presented a paper on an evaluation and design procedure used in a study of a proposed nuclear waste repository (Owen, Scholl, and Brekke, 1979).

Jan 1, 1985

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,200 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. High density of joints occurs within the host rock. Based on Rock Mass Rating and field observation, the Leeville ground conditions are characterized as poor to very poor. As such, heavy ground support is required for the mining operation in Leeville. Ore zones with a height in excess of 10 m (35 feet) are considered for longhole stoping. A typical stope measures 6.0 m (20 feet) wide, 30 to 55 m (100 to 180 feet, depending on the ground conditions) long and 10 to 30 m (35 to 100 feet, depending the thickness of ore body) high, yielding 10,000 to 20,000 tons when completed. Narrow ore zones, less than 10 m (35 feet), are mined using cut and fill. These drifts are 4.6 m (15 feet) wide by 4.6 m (15 feet) high. Based on the afore-mentioned poor ground condition, the establishment of a ground control monitoring system is key to operating both safely and successfully. The ground control monitoring system is composed of comprehensive instrument design and installation. Instruments include Multi-Point Borehole eXtensometers (MPBX) and Stretch Measurement to Assess Reinforcement Tension (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two year?s applications and measurements, useful data has been and continues to be collected to use in future stope and infrastructure structure design. The system provides the information making engineer and operation teams to do their job more confident and efficiency. Keywords: Ground control, Monitoring system, Long hole stope, Instrumentation.

Jan 1, 2009

By Manuel Gomez

Bituminous coals having maximum fluidity values in the 40- to 25,400-dial-divisions-per-minute (ddpm) range were carbonized in a continuous, entrained-bed reactor. Carbonization was conducted in an 8-inch diameter, vertical reactor at temperatures from 955° to 1,345° F and at air-to-coal ratios ranging from 4.63 to 16.12 scf/lb of moisture-and ash-free coal charged. Carbonization rates from about 118 to 360 lb/hr, as-carbonized basis, were examined. It was demonstrated that carbonization temperature and air-to-coal ratio must exceed minimum values for continuous operation. Within the operating conditions discussed, highly fluid bituminous coal was carbonized to produce tar and nonagglomerated char. The yield of tar ranged from 21.3 to 38.9 gallons per ton and the char yield ranged from 1,109 to 1,563 pounds per ton, all units expressed on a moisture-and ash-free basis. It was demonstrated that the maximum fluidity and the average size of the coal along with the air-to-coal ratio and the carbonization temperature act together to influence the carbonization product yields and certain properties of the products. Prediction equations were developed from the data for product yields and selected properties of the char, tar, and gas.

Jan 1, 1968

By George P. Jr Schivley

Looking at the process of drilling rock from the standpoint of the power required, yields an equation that relates Force-on-the-Bit; Torque, to rotate the bit; and bit Angular Speed to the Penetration Rate of the bit; the Area of the hole being drilled and the Specific Fracture Energy of the rock. Specific Fracture Energy and the Compressive Strength of the rock are related.

Jan 1, 1994

By Michael E. Berndt

Asbestos first became an issue to Minnesota?s iron industry when it was revealed that mineral fibers similar to those in Reserve Mining?s tailings were being found in drinking water for several communities that used Lake Superior as their primary water source. This discovery turned what had largely been an environmental court battle into a case concerning public health. The courts listened to much conflicting and uncertain scientific testimony on the size and distribution of the mineral fibers and on the potential health effects imposed by them. In April 1974, the plant was ordered to shut down by a federal judge but the company quickly appealed the decision. The appeals court granted a stay and ultimately ruled that the plant?s closure could not be justified based on the unknown health effects of the mineral fibers since the consequences of such an action would have immediate and severe social and economic impacts. The plant was allowed to continue operation, but ordered to abate emissions to air around the plant and to switch to a land-based tailings disposal system. Much of the scientific uncertainty and public concern over mineral fibers in Minnesota?s taconite industry remain today. ©2007 Elsevier Inc. All rights reserved. Keywords: Minnesota; Iron ore; Taconite; Asbestos; Amphibole; Reserve Mining; Tailings; Mesabi Iron Range

Jan 1, 2007

This work presents: 1.) the results obtained from measurements of temperature profiles in pillars and at working faces of three coal mines located in Colorado and New Mexico, 2) a comparison of the experimental results with theoretical predictors based on linear heat flow models, and 3) temperature profile predictions based on a two dimensional coal mine model with an inclined crack located in the roof or wall of the opening. The thermal properties of the coal and shale samples taken from the mines were used as input data for the computer model. Good agreement was found between the measured profiles and the theoretical values obtained with the one dimensional model. The two dimensional model results show that a visible crack (0.01-0.07-ft thick) in a coal roof causes a surface temperature difference from 0.2 to 1°F at the edge of the crack for rock exposed to air from 1 hr to 288 hrs and with the air to rock temperature differences from 2°-6°F. A temperature difference of 0.3 °F was found between solid and broken rock in a shale roof with a 0.03-ft thick crack inclined 45° to the horizontal after a ventilating time of 48 hrs and the air to rock temperature difference of 2.1°F.

Jan 1, 1972

By Walter D. Holland

This is one of a series of instruction guides developed to help instructors present health and safety training courses to workers in the metal and nonmetal mining industry. This course is intended for training those, usually the safety officers, who perform surveys for inhalation contaminants in above ground work areas. The handbook entitled ?Handbook for Surveys of Inhalation Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas? is used as a manual for the course and as a prime reference when performing the actual surveys or interpreting the sampling results. There are six experiments for the students to perform during the course to familiarize them with the sampling devices routinely used during the surveys.

Jan 1, 2011

By B. Samoski

In late 1994, EPA and OSM acknowledged that efforts by any one agency or by the many different agencies to remedy the water quality impacts of decades of contamination from abandoned coal mine lands in Appalachia would not be successful if their disjointed efforts were not unified and if the local watershed organizations were not included. The result of the collaboration between EPA and OSM was the creation of a statement of mutual intent which was a pledge by government agencies, watershed organizations, and the industry to restore watersheds degraded by acid mine drainage from abandoned coal. The presenter will describe the evolution of this pledge from a paper promise to on-the-ground remediation projects.

Jan 1, 2002

By Henry M. Howe

PART I. § 1. Introduction. After giving certain definitions, this paper gives the reasons which led to Roozeboom's form of the diagram of the freezing-point curves and general equilibrium of the iron-carbon compounds, steel and cast-iron ; and then those which led to replacing it with the present or double diagram, in which graphite is at all temperatures held to be the more stable and cementite the less stable (metastable) form of carbon. Next in § 10 the evidence supporting this greater stability of graphite is examined, then in § 17 that which seems to oppose it, and in § 22 a summary of the evidence is presented. The second part of the paper considers the topography of the graphite-iron diagram, rejecting summarily the solubility-lines based on the data of Charpy and Grenet and of Mannes-mann, on the ground that the data even on their face do not really point toward these lines, and that they are wholly incompetent to determine any solubility-lines whatsoever, because they report together with the dissolved carbon also an indeterminate quantity of cement-carbon, and because even such carbon as is actually dissolved, only in part represents the solubility of graphite, and in another and indeterminate part represents the solubility of cementite, or at least of carbon in presence of cementite as distinguished from graphite. It might be thought that graphite is but slightly soluble in iron, because of the absence of any suggestions of eutectoid graphite, corresponding to the eutectoid cementite of pearlite in very many cases in which the cast-iron seems to consist of ferrite and massive graphite only, and because of the micrographs of Goerens and Gutowsky. In these the primary austenite of cast-iron quenched but little below the eutectic freezing-

Jan 7, 1908

In 2005, CANMET-MMSL used its pool of expertise in ground control, open pit and underground mine engineering, mineral processing, information technology and applied mineralogy to launch a mine-to-mill research project. The objective of the project was to optimize the distribution of rock breakage energy among blasting, crushing and grinding activities, thereby maximizing the efficiency of energy utilization within comminution processes. Tests were designed to demonstrate that this approach could reduce energy consumption, thus contributing to the reduction of green house gas (GHG) production in the Canadian mining industry. The project was accomplished in collaboration with DynoConsult and Dyno Nobel Canada Inc., a world leader in commercial explosives. Data analysis from 12 blasts (six with electronic and six with pyrotechnic detonators) in three different geological formations of a quarry (soft, medium and hard rock) shows that electronic blasting technology increases rock fragmentation by 15% (in hard rock) to 20% (in soft rock). A more uniform rock fragment size distribution is also obtained. The impact of the improved quality blast product on downstream processes of the quarry is a productivity increase of 5% in rock excavation and transportation, an energy reduction of 10% at the primary crusher and an increase of 15% of the primary crusher throughput. Extended to the Canadian mining industry, such results would represent a GHG emission reduction of about 0.05 Mt/y. A soft-sensor prototype, based on primary crusher data (i.e., energy consumption, throughput, feed and product size distribution) and a simplified computerized process model, was developed for on-line measurement of the rock operating work index. Additionally, 385 rock samples and specimens were collected and prepared to determine the tensile and compressive strength of the rock material, to evaluate the aggregate crushing work index and to examine the development of micro- and macro-fractures by means of binocular and SEM microscopy. Blast-induced rock damage was evaluated at the end of the laboratory-testing program. Even though a reduction of rock hardness of around 30% was observed after blasting, the impact of the blasting method (i.e., use of electronic or pyrotechnic detonators) on the induced rock damage could not be observed. It is either absent or not perceptible with the accuracy of the measuring techniques and the number of samples analyzed.

Jan 1, 2008

The seams of black coal occurring in Victoria are so disturbed by faulting, wash-outs, thinning, etc., that it is necessary, for the prevention of costly errors in development, that close boring be undertaken so that the correct positions of the shafts, tunnels, main and auxiliary roadways can be set out in order that the area can be economically worked. The State Coal Mine has two boring plants continuously at work, which have given good service for the last twenty-five years.The information supplied herein is merely our experience in boring at the State Coal Mine over an extended period. The type of plant in use is that known as the Victoria Drilling Plant, equipped with an 11 h.p. portable oil engine, using power kerosene as fuel. It was purchased in 1914, complete with mechanism for cable drilling, capable of boring to a depth of 1500 ft. with a guarantee of 1000 ft., with Calyx cutters, boring rods and all necessary equipment for the sum of £1473. The chief mechanical features of the plant are as follows:-The derrick is in the shape of a tripod (see Fig. 1), two of the legs being of steel channel built together to form a frame which, when lowered on to two sets of road wheels, forms a carriage for the transport of a portion of the boring equipment. The third leg is made of oregon in the form of a double bow, with bolts and distance pieces between the wooden sides. The top of this is hinged on to the steel frame, and the bottom is fitted into a cast iron block, having two small wheels to facilitate erection. A rope attached to the cast iron block and to the winch easily...

Jan 1, 1936

By J. J. Shields

This study by the Federal Bureau of Mines concerns different methods of face haulage used with various types of continuous-mining machines, mobile-loading machines, and track-mounted equipment under varying roof and bottom conditions and in coalbeds of varying thicknesses. This report is the ninth in a series on mechanical mining in bituminous coal mines. Reference to the reports previously published is made in appendix III, p. 106. Use of modern mining equipment in bituminous coal mines has resulted in increased productivity at the face. This especially is true where continuous-mining machines are used, and the supervision is good. Previous methods and equipment for moving coal from the face became inadequate and had to be improved to restore balance to the mining systems. Sometimes new equipment was needed to improve the face haulage, and in some instances, a new combination of existing equipment was used. Detailed studies of face haulage methods were made at 13 mines in Pennsylvania, West Virginia, Ohio, and Illinois to compare their effectiveness and to describe fully the conditions under which each method was used.

Jan 1, 1960

By C. R. Copeland

Water sprays are a common method used to reduce particulate matter (PM) emissions. Various factors such as wettability, surface area coverage, fine particle engulfment rates, interparticle adhesion forces, suppressant penetration and suppressant longevity have all been suggested as critical factors in achieving effective PM control. However, it has not been established which of these factors are the most important. Experimental work indicated that suppressant penetration is the most critical of these factors. The length of time after application that suppressants were effective was also improved by using hygroscopic reagents that retained moisture to prevent evaporation. Maximizing suppressant penetration and improving suppressant longevity led to an average 86% reduction in PM10 concentrations in laboratory dust tower tests.

Jan 1, 2008

By Alla D. Mah

Relatively pure aluminum nitride (AIN) recently has been prepared in sufficiently large amounts to permit a variety of experimental studies.4/ Several mechanical and chemical properties have been investigated, which show that this substance has good potentialities as a container for liquid aluminum, gallium, and boric oxide. The present work by the Bureau of Mines was undertaken to obtain thermo-dynamic data pertinent to the calculations regarding thermal stability and reactivity of aluminum nitride. The following measurements were made: (1) determination of the heat of formation from the elements at 298.15° K.; (2) determinations of the heat capacity over the temperature range 51° to 298.15° K. and the evaluation of the entropy at 298.15° K. therefrom; and (3) determinations of the heat content over the temperature range 298.15° to 1,800° K. These data are combined to obtain free energies of formation from the elements between 298.15° and 2,000° K.

Jan 1, 1961