Search Documents

By Shadia J. Ikhmayies

"Tin oxide (SnU2) thin films of thicknesses in the range 100-600 nm were prepared on glass substrates by vacuum evaporation at ambient temperature. The films were characterized by transmittance measurements, X-ray diffraction (XRD), scanning electron microscope (SEM) observations and energy dispersion X-ray analysis (EDAX). It is found that the films have high transmittance and non sharp absorption edges. XRD diffractograms showed that the films are amorphous and the SEM micrographs showed that the surfaces are smooth, uniform and well covered with the material. The EDAX analysis showed that the films are deficient in oxygen. Indirect optical bandgap energy and Urbach tailing in the bandgap was observed, and the width of the tail, which is related with disorder and localized states, was estimated.IntroductionTin oxide is an n-type wide bandgap semiconducting material with a direct bandgap energy of 4 eV and an indirect bandgap of 2.6 eV [1], where inherent oxygen vacancies act as an n-type dopant [2], Tin oxide thin films have been used for transparent electrodes in photoelectric conversion devices namely amorphous silicon solar cells, liquid crystal displays, gas discharge displays, etc. [3]. Perfectly amorphous thin SnO2 films show good electrical response to reducing gases in air and could, hence, be applied to construct semiconductor gas sensors where the metal oxide films function as a monograin-eqivalent active layer [4]. Amorphous SnU2 can also be used in extended gate field-effect transistors (EGFET) as a pH sensor, where the sensitive part is made of the SnO2/Al structure. This device can be used to detect and to quantify any kind of substance that can produce or consume protons, like an enzymatic reaction, therefore showing a large range of applications as biosensors [5].There are different methods to prepare SnO2 films, such as atomic layer deposition (ALD) [6], reactive magnetron sputtering [7], chemical vapor deposition [8, 9], dip coating [10], spray pyrolysis (SP) [3, 11-14], and evaporation [8], The thermal evaporation method was chosen to produce SnO2 thin films in this work because deposition by this technique does not present any compositional problems. In addition, it is a low temperature technique, which increases the probability of producing amorphous films. To increase this probability, the films were deposited at ambient temperature."

Jan 1, 2012

By L. R. Verney

A number of interrelated factors influence the economics of the sulphide smelting of copper, lead, zinc and nickel. This paper discusses these factors, mainly from a US point of view, and shows how they affect the cost of construction and operation of new and existing plants. The paper shows how metallurgical plant construction costs and the consumer price index have increased at a much faster rate than metal prices thereby making some metal mining and production operations within the USA, Canada and the EEC less profitable than operations elsewhere. This in turn inhibits new "grass roots" metallurgical developments. It is explained how retrofit of existing pyrometallurgical plants can be a more viable development than the construction of "green field" plants, especially if such retrofit improves, energy efficiencies, overall operating costs and reduces emissions of sulphur and other toxic wastes. Some aspects of metallurgical plant operation are examined, especially for copper and nickel, to show how changes in operating practices may develop in order to improve overall smelting economies, especially when developed in conjunction with objective retrofit. The paper also examines some financial aspects, especially insofar as the disparity between terms for loans offered to third world countries and the USA and the EEC are concerned and also comments upon the need, especially within the USA, for legislation to permit rapid depreciation of capital. Specific comments are made about environmental aspects, including the lack of uniformity of pollution control legislation and how environmental considerations may have some bearing of the location of future smelting operations.

Jan 1, 1983

By Yiling Zhang, Paul A. Salvador, Gregory S. Rohrer

"Photocatalysis utilizes solar energy to produce hydrogen by splitting H2O. When a thin film of photocatalyst TiO2 is supported on a ferroelectric BiFeO3 substrate (band gap ~2.5 eV), the TiO2/BiFeO3 heterostructure is capable of photochemically reducing Ag+ to Ag0 in aqueous solutions under blue light with enhanced efficiency. The observation of spatially selective silver patterns on surface of the heterostructure after reaction suggests that photogenerated electrons and holes in ferroelectric BiFeO3 are driven in opposite directions to reduce their chance of recombination. Comparisons of the amounts of reduced silver on TiO2 film grains with distinct phases/orientations show that the reactivity is mildly preferential on anatase TiO2 phase and does not strongly depend on crystallographic orientation of BiFeO3.IntroductionTitania (TiO2) is capable of photocatalytically converting H2O to hydrogen and oxygen under the irradiation of ultraviolet light. [1, 2] One of the limiting factors for titania to be used as an effective photocatalyst is its band gap. Because the absorption edges of rutile and anatase titania are at 3.0 eV and 3.2 eV, respectively, they can only absorb light in the UV portion of the spectrum, which is about 3% of the available solar energy. [3-5] This limitation has motivated attempts to modify the absorption edge of titania so that it can absorb visible light.One strategy is to substitute a portion of the titanium and/or the oxygen with other atoms. There are numerous reports on visible light absorption of titania by doping and co-doping of Cr, V, Mo, Sb, Fe, N, S, C, and F. [6-34] Another strategy is to add an adsorbed molecular species that absorb visible light and donate an electron or hole to the titania, such as organic dyes [33, 35, 36] and Ce3+/Ce4+. [37, 38]The strategy in the present work takes the approach of depositing a pure titania thin film on a visible light absorbing substrate BiFeO3 to induce visible light activity of the heterostructure. BiFeO3 is a semiconductor with a band gap of about 2.5 eV [39-41] and is photocatalytically active in visible light. [42, 43] It is also ferroelectric with spontaneous polarization along pseudo-cubic <111> directions of 6.1 µC cm-2. [44] The spontaneous polarization gives rise to internal electric fields that drive photogenerated charge carriers, namely electrons and holes, in opposite directions to reduce their chance of recombination. [45-47] Additionally, the separation of electrons and holes leads to the spatial separation of reduction and oxidation half reactions so that the back reaction of intermediates is also suppressed. Such charge carrier separation has been reported in TiO2/BaTiO3 heterostructures with UV light illumination. [48-51] The TiO2/BiFeO3 heterostructures in this work combine both advantages of the relatively narrow band gap and the internal fields in BiFeO3 to enhance the overall photocatalytic activity."

Jan 1, 2014

By J. Hamisch

Climate policy regarding perfluorocarbons (PFCs) may have a significant influence on investment decisions in the production of primary aluminum. This work demonstrates an integrated analysis of the effectiveness and likely economic consequences of different climate policy options. In our study we first compare atmospheric observations to the available estimates of PFC emissions for the baseline years 1990 and 1995. We then present projections for regional emissions of PFCs from the aluminum industry using the MIT Emissions Projection and Policy Analysis model under different policy scenarios. Abatement costs for emissions of PFCs and C02 are compared in the context of the Kyoto Protocol.

Jan 1, 1999

By O. Forsén

A new cell construction was designed for the study of the electrochemical behaviour of additives in conditions that simulate real copper, electrorefining. The behaviour of gelatine and thiourea was studied by applying different electrochemical methods, i.e. polarization resistance and voltametric measurements. In this study, individual galvanostatic electrolysis experiments were carried out for 120 hours. The organic additives were introduced to the electrolyte at certain intervals and their concentration was varied in the range &om zero to four ppm. An optical microscope was applied for the examination of copper cathode deposit microstructures. The results show that gelatine has a polarizing effect on the deposition potential of copper whereas even small amounts of thiourea depolarize the electrodeposition of copper. The maximum inhibitor efficiency of gelatine was obtained at a gelatine concentration of slightly lower than two ppm. When both gelatine and thiourea were present in the electrolyte, the depolarizing effect of thiourea exceeded completely the polarizing effect of gelatine. If chloride ions were added to gelatine and thiourea containing electrolyte, the electrochemical behaviour of the system was altered drastically. Chloride ions resulted in the prevailing of polarization effect caused by gelatine while the depolarizing effect of thiourea disappeared in this system. The polarizing effect of gelatine increased until chloride ion concentration of 30 ppm was reached. Also, the above electrochemical phenomena could be detected in the optical examination of copper deposit microstructure.

Jan 1, 1995

By Joseph Hamuyuni, Fiseha Tesfaye, Daniel Lindberg

E-waste management through traditional methods such as disposing in landfills, burning in incinerators or exporting abroad for disposal are no longer options due to the strict environmental regulations. Fortunately, the presence of valuable metals in the e-waste and increasing demand for the metals as well as complexities of the currently available primary raw materials make recycling an attractive and viable option both environmentally and economically. Moreover, it is efficient in terms of resource management by closing the loop of metals. Consequently, urban mining such as the recovery of precious metals from e-waste streams through sustainable recycling processes have emerged. The sustainable recycling practices address the scarcity of primary resources and reduce consumption of energy for metals production while managing environmental issues related to hazardous materials from the e-waste streams. In this paper, valuable metals recoveries from e-waste streams through pyrometallurgical and hydrometallurgical processes are critically reviewed. And, innovative ideas for different steps of the thermochemical processes in the valuable metals and energy recovery from the e-waste streams are discussed.

Mar 1, 2017

By S. N. Sinha

The distribution coefficients of lead and silver between copper and matte phases have been measured at two different temperatures. Experiments covered the ranges of 0.009-1.8, 0.07-0.13, and 0-11 wt pct lead, silver, and iron in matte, respectively. The distribution coefficients of lead have been measured at 1405 and 1505 K and correlated with lead and iron concentrations in metallic copper and matte. The values of the distribution coef¬ficient of lead between copper and iron-free matte, at infinite dilution of lead, have been determined to be 3.60 and 4,06 at 1505 and 1405 K, respectively. The distribution coefficient of silver between copper and iron-free matte is independent of silver concentrations and has been measured to be 2.13 and 2.21 at 1400 and 1500 K, respectively. For an iron-bearing matte, the distribution coefficient of silver has been correlated with iron concentration in the matte at both 1400 and 1500 K. From the measured values of distribution coefficients, the Raoultian activity coefficients of PbS and AgS0.5 in copper-saturated matte have been calculated. At infinite dilution, the following equations correlating the Raoultian activity coeffici¬ents of PbS and AgS0.5 with matte- composition and temperature have been obtained: log Y° PbS =1.515 + 1080/T 0.14 NFes lbS Fog YAgS = -0.074 - 425/T + 0.09 NFes. - 0.5

Jan 1, 1983

By U. Lauwers

The influence of different waste materials in sinter blends on the quality and mineralogical composition of a sinter is described. As a result of partial preservation of the original textures of waste materials in the final product the degree of assimilation of the original material in the sinter product can be ascertained. Recycling of waste materials such as dolo char , arc-furnace slag, scrap fmes, mill scale and BOF-mud via the sintering process a saving on costs of raw materials such as flux and fuels, and a reduction on pollution can be achieved. A comparison of a typical sinter with a sinter produced through the utilization of waste materials showed a distinct correlation between certain types of waste material and some metallurgical properties. Dolochar in a sinter blend acts as part of the fuel and flux that are normally added to a sinter mix. Generally dolochar improves the quality of the sinter and decreases the consumption of coke. Other waste materials adversely influence the quality of the sinter. The glass and calcium ferrite content of a sinter when dolochar is used in the blend is similar to that of a sinter produced with only coke as a fuel in the sinter mix. The glass content is lower and the calcium ferrite content is higher, in a sinter produced from dolo char in the blend compared to a sinter produced with additions of other waste materials. Changes in the mineralogical composition are related directly to the metallurgical properties of the sinter product.

Jan 1, 1991

By K. J. Martchek

"This introductory presentation will highlight recent efforts to quantify the positive value of recycling metals such as aluminum, magnesium, lead, zinc, nickel and copper in relation to the three pillars of ""sustainable development"" - environmental protection, economic development and improve social consequences.This presentation will provide an overview of life cycle assessment profiles increasingly being utilized by customers, regulators and environmental advocacy groups to holistically evaluate the environmental performance of materials and products. The environmental profiles of prodi.lcts containing recycled metal will be presented based on rules established by the International Organization for Standardization (ISO).Significant to the life cycle profile of metal products is recent confirmation. that recycling has the potential to reduce materials production energy consumption by 95% for aluminum, 80""/o for magnesium and lead, 75% for zinc, and 70% for copper. Furthermore, . ""metals are eminently and repeatedly recyclable, while maintaining all their properties (1 ). "" Their durability relative to many hydrocarbon based materials enhance .their life cycle performance. However, the persistence of metals when dispersed into our natural environmental makes recovery and recycling particularly important Overall, when considering life cycle effects, recycling is critical to a sustainable future for metal products.Finally, regional and international regulations will be highlighted which will effect the efficient recovery and recycle of metals and their overall contribution to environinental protection, economic development and the enhancement of society."

Jan 1, 2000

By T. T. Chen

A mineralogical study of copper anodes and copper anode slimes was carried out to elucidate the silver phases present and the behaviour of silver during copper electrorefining. Most of the silver in the anodes is in metastable solid solution in the copper metal. As the copper dissolves, silver also dissolves, but is rapidly removed from solution by a variety of reactions. Some of the silver is precipitated as Ag by cuprous ions and some is precipitated as a complex CU-Ag-Pb-As-Se oxidate phase. Much of the silver, however, reacts with copper selenides to form, progressively, (CU,Ag) 2se, AgCuSe and Ag2se. The reaction commences at the periphery of the selenide grains and progresses inward; the result is commonly a silver-rich species on the outside of a silver-deficient core. Slimes collected periodically throughout the electrorefining cycle show a progressive silver enrichment of the selenides. Traces of Ag2Te also may be present, but the telluride seems to J:ie a rare constituent of most raw anode slimes.

Jan 1, 1989

By G. Upadhya

Of late, solidification modeling has progressed considerably to emerge as a viable simulation tool for the foundry engineer. A wide variety of tools exist in the commercial market to cater to the various needs of the design/ foundry engineer. In fact, recent developments in the area of solidification modeling have been so rapid that a comprehensive review of the state-of-the-art is very much needed. In this paper, an attempt is made to summarize the various issues of solidification modeling, at the same time addressing the historical evolution of the subject. The various phenomenological issues covered in this paper include: heat transfer, fluid flow during mold-filling, solidification kinetics and microstructural evolution, quick-analysis schemes for approximations, porosity prediction models, and the phenomena of fluid flow in the mushy zone. Modeling issues related to the development of solidification stresses which lead to defects such as hot tears and the development of artificial intelligence concepts in the area of rigging design are also discussed. Due emphasis is given to the various phenomena which add to the complexity of the whole subject, and the various alternatives available for solving a particular problem. For example, the heat transfer problem can be approached by the use of simple modulus schemes or by solving the conduction equation to obtain a more accurate temperature distribution. Similarly the microstructural evolution can be handled in a deterministic way by use of nucleation and growth models, or in a probabilistic way by use of empirical models. The main goal of this paper is to put the multi-faceted problem of solidification modeling in proper perspective so that it can serve as a guide for future developments in this area.

Jan 1, 1994

By H. J. Roorda

With an increasing need to obtain metals by processing complex fine intergrown ores, the use of electron-optical techniques will become more important as a tool for mineralogical studies. Electron images enable a higher spacial resolution than can be obtained by optical microscopy and thus provide a powerful and necessary aid for the examination of small grains and finely locked particles. In this paper the mineralogy of Meggen ore was investigated. Both light-optical and electron-optical techniques were used to evaluate the mill feed and products of the concentrator. Detailed examination by reflected-light microscopy to assess the comportment of galena in the complex pyritic ore was inconclusive in establishing the cause for low lead recovery of only forty percent of the ore&apos;s lead content. Electron microprobe analyses indicated that the majority of the lead lost to the tailings was accounted for by extreme fine (often smaller than one micron) and complex intergrowths of galena in pyrite. The remainder was lost as fine free galena grains.

Jan 1, 1987

By H. M. . van der Donk

In this work an overview is given about the techniques available for the removal of metallic impurities from molten aluminium. The overview is focused on the removal of iron. Also, some experimental results are given about the creation of iron-rich intermetallic compounds in an aluminium system, which are subsequently removed by gravity segregation and filtration techniques. This work is part of an ongoing research project of three major European aluminium companies who are co-operating on the subject of recycling of aluminium packaging materials recovered from household waste by means of Eddy-Current techniques. Using this technique the pick-up of some contaminating metals, particularly iron, is almost unavoidable.

Jan 1, 1995

By Jinfu Xu, Youqing Cao, Yuting Lv, Hang You, Peng Jiang

"In present work, we reported the fabrication of composites consisted of M42 powder metallurgy high speed steel and 45 steel at one step via spark plasma sintering (SPS) technology. The interface microstructure, compositions and microhardness with the interface forming mechanism were investigated. The results show that the morphology and microhardness within the M42/45 steel interfaces exhibit a gradient distribution. The interfaces possessed a transition layer up to 10.2 ?m with few distortions and microcracks. The formation of M42/45 steel interfaces were driven by both fusion and diffusion processes. The former one was primary at the early sintering process, while the later one becomes dominant over the followed sintering process.IntroductionPowder high-speed steels have been widely used in cutting tools, cold-hot tools and dies, as well as in cut materials and structure parts with wear resistance and high-temperature resistance, due to its high hardness, good wear resistance, desirable cutting toughness and favorable hot hardness [1-2]. For materials of some parts in practical production, not only the favorable toughness is required to resist the impact action, but also the high hardness and exceptional wear resistance are demanded. According to the functional requirements and working conditions, bimetal composite materials are prepared in a certain mode, proportion and distribution, by designing two metals with different chemical and physical properties [3-6]. Considering the composites exhibit different properties in different positions of the parts with a combination of the advantages of two metals, they can obtain enhanced properties that the single one can not achieve."

Jan 1, 2012

By M. Krishna, Jayagopal Uchi1, Shanta Sastry, B. M. Satish

"A well-considered composite of ZA-27 reinforced with weight percentage 0, 2, 4, and 6% of alwninite particulate has been made by compocasting technique. The elastic properties of ZA- 27 /alwniniute particulate composite were determined by using U1M. The results showed that the modulus of elasticity and UTS of the composite gradually increases with increase in the wt.% of reinforcement. However, the overall ductility decreased monotonically with an increase in reinforcement. The results of these tests· as well as the predictions of several model~ for composite strengthening available in the literature were compared with experimental results. The data observed from Young's modulus by measurements studies were compared with theoretical results predicted by Eshelby model.IntroductionMetal matrix composites (MMCs) have received increasing attention in _the recent decades as engineering materials. The introduction of a ceramic reinforcement into a metal matrix produces a composite material resulting in an attractive combination of physical and mechanical properties that cannot be obtained with monolithic alloys. Particulate reinf9rced MMCs among the discontinuously reinforced MMCs have attracted quite a lot of attention both in the industrial sectors and the academic communities. There is an increasing need for knowledge about the processing techniques and mechanical behavior of particulate MMCs in view of their production getting enhanced and their commercial applications becoming wider [I]. Interest in particulate reinforced MMCs is mainly due to easy availability of particles and economical processing techniqu"

Jan 1, 2000

By P. A. Botha

Most sinter producers prefer to use a range of iron ores with the aim to optimize their sinter blends. ISCOR is however limited to the use of ore from two deposits, namely Sishen and Thabazimbi. Only sinter produced from Sishen ore is described in this report. The Sishen iron ore deposit provides high-grade hematite ore with a mean iron content of 65 per cent. Three major ore types are developed: massive, laminated and conglomeratic. The main ore mineral is hematite with minor to trace amounts of quartz, mica, phosphates and, in places, carbonates. A sinter product is characterized by its mineralogical composition and metallurgical properties. The production rate also plays an important role in the economic evaluation of sinter quality. Sinter-pot tests were conducted with varying basicities, given as the ratio of CaO to SiO:< and coke content. The results of these tests were characterized by mineralogical and metallurgical methods. Basicity of a sinter mix directly influences the mineralogical composition and metallurgical properties. The content of calcium ferrite and calcium silicate increases with increasing basicity, thereby increasing the reducibility and cold strength of the sinter product. Experiments performed during this study provided a model for the optimization of the sinter mix with respect to its mineralogical and metallurgical parameters.

Jan 1, 1991

By Huimin Lu, Qiang Li, Jingbo Xu

"The smelting reduction of V-Ti bearing beach placer by combined rotary hearth furnace and direct current arc furnace was studied in laboratory. It takes the aid of back propagation (BP) neural network theory to build the nonlinear mapping relations between the crucial process variables such as content of carbon, temperature and time and the degree of reduction. Then by the integrating BP neural network and genetic algorithm (GA), the optimized process parameters for the high degree of reduction were searched. The comparisons between experiment results and neural network simulation results show that GA-based on BP method can predict the degree of reduction with higher prediction accuracy. Calculations show that the integrated energy consumption of new technology is 580kgce/tHM, less than the current existing blast furnace.IntroductionThese V-Ti bearing beach placers (VTBBP) are secondary Fe-rich minerals formed by rivers, ocean waves, ocean tides and ocean currents on beach zones, their useful minerals are V-Ti magnetite ores. On Asia Pacific zone, such as Japan, China, Philippines, Indonesia, Australia and New Zealand, the VTBBP have large reserves and wide distribution. But so far, the VTBBP are not still comprehensively utilized. Therefore, in this paper, a combined rotary hearth furnace technology and arc furnace smelting method is studied for comprehensive utilization of the VTBBP. The main objective of this paper is to find optimum operation conditions for the production ofV-bearing iron and titania-rich slag from the VTBBP by means of the laboratory testing.Recently, neural network (NN) expected to be able to provide an effective tool because of its advantages, which describe nonlinear mapping relations. With the characteristics of strong selflearning, self-organization, robust error toleration and accurate nonlinear relation approximation, artificial neural network can be applied to nonlinear process modeling based on sufficient training. Back-propagation (BP) training algorithm is probably the frequently used one in practical application. Genetic algorithm has parallel search strategy and global optimization characteristics, which makes the trained neural network being higher classification accuracy and faster convergence speed. So it is necessary to combine neural network and genetic algorithm. The nonlinear relationship between input and output presented by NN and the global optimal function of GA are abroad applied in the engineering and scientific research [1, 2]. So these methods supply an efficient path to solve the above problems. At present, it is common to study the optimization of process parameters by orthogonal experimental design, the method combining neural network and genetic algorithm is a novel and better method than orthogonal experimental design. Tills study organized the above advantages to optimize the process parameters for comprehensive utilization of the VTBBP."

Jan 1, 2012

By Fiseha Tesfaye, Pekka Taskinen, Daniel Lindberg

Due to increasing complexities of raw materials for base metals production the conventional pyrometallurgical processes are challenged. To make the appropriate modifications, thorough evaluations of the thermal stabilities of phases and phase assemblages which are commonly encountered in these processes are essential. In this work, phase relations and thermal stabilities of equilibrium phases in the Cu-Ni-S system have been reviewed. The calculated phase diagram of Cu-Ni system has been validated. At T < 630 K, in the Ni-rich corner, large scatter in data has been observed and discussed in detail. The other binary systems, Cu-S and Ni-S, have been also critically reviewed together with the ternary Cu-Ni-S system. The reviews were focused on compiling and discussing phase relations and thermal stabilities of the selected systems in the pyrometallurgical processes of Cu and Ni productions.

Jan 1, 2016

By Y. Pokhvisnev, S. Vandariev, A. Yatshenko-Juk, V. Valavin, V. Romenets

The technology of the liquid-phase reduction process known as Romelt was developed in the Moscow Institute of Steel and Alloys in 1979. The pilot plant was constructed at the Novolipetsky Steel Works (Russia) in 1984. Investigations into processing zinc-containing blast oxygen furnace dust and slag from the Lead and Zinc Works at the pilot Romelt plant proved the perspective of using this technology for processing zinc and lead-containing materials. In this article, the description of Romelt technology, basic technological information of trials at the Romelt plant using zinc-containing materials, compositions of charging materials, metal, slag, gas and dust are presented. The influence of flue gas composition on the composition of zinccontaining dust is shown.

Jan 1, 2000

By Kaixi Jiang, Lan Li, Bang Wei, Haibei Wang, Yaping Feng

"China is currently the world's largest copper producer. In the last five years, 950 kt/y of smelting capacity was commissioned. Currently, about 1200 kt/y smelting capacity is under construction and about 2000 kt/y smelting capacity is under feasibility study. Ausmelt/ISA smelting and flash smelting technologies were commonly adopted in China. After the double-flash-smelter was first adopted in 2004, three new double-flash-smelters are scheduled. Recently, two new copper smelting technologies were developed in China. One is an improved bath side-blown smelting process, and another is the SK.S bottom blowing process. Both technologies have been in practice for over three years and have achieved good technical performance. Approximately 500 kt/y new smelting capacity in China and India will adopt these technologies. Both technologies have the advantages of low investment cost, low energy consumption and high flexibility for complex raw materials. This paper reviews ""green"" copper smelting projects in China and introduces the practices of the two new Chinese smelting technologies.IntroductionPresently, China is the largest copper producer in the world. As far as the smelting of copper is concerned, there are many smelting processes applied in industrial production, such as flash smelting, Noranda smelting, Ausmelt smelting, Isa smelting, the Mitsubishi process, Vanukov smelting, silver copper-smelting, SKS smelting, both side-blown smelting, traditional blast furnace smelting, electric furnace smelting, reverberatery smelting and so on . Except the last three traditional processes that are eliminated because of their failure to meet the requirements for environmental protection, all of the other above-mentioned methods are advanced smelting processes adopted nowadays."

Jan 1, 2012