Search Documents

By G. A. Brooks, R. W. Matusewicz, Nazmul Huda

"A computational fluid dynamic (CFD) model of a conventional tuyere blown slag fuming furnace has been developed in Eulerian multiphase flow approach. The model was developed by coupling CFD with kinetics equations developed by Richards et al. for zinc fuming furnaces. The model integrates submerged coal combustion and chemical reactions with the heat, mass and momentum interfacial interaction between the phases in the system. The model predicts the velocity, temperature field of the molten slag bath, generated turbulence, vortex and coal utilization behavior from the slag bath. The highest coal penetration distance was found to be at l/L = 0.2, where / is the distance from the tuyere tip and L is the total length (2.44m) of the modeled furnace. The model also predicts that 10% of the injected coal bypasses the tuyere gas stream un-combusted and carried to the free surface, which contributes to ZnO reduction near the free surface.IntroductionSignificant metal values are often discarded with slag in the form of metal oxide produced by the smelting industries. These metal values can be recovered from the slag by proper treatment. Zinc slag fuming is such a process, where a reductant source (usually coal) is injected in the molten slag bath to reduce dissolved ZnO from the bath into metallic zinc vapour. The process can be carried out in either conventional tuyere blown furnace or top submerged lance (TSL) smelting furnace. Conventional slag fuming processes are carried out on batch basis in a rectangular tuyere blown furnace. Approximately 50 tonnes of charge (either molten slag or solid slag) is fed to the furnace at the beginning of each fuming cycle. Two opposing sets of submerged tuyeres are employed to inject air and pulverized coal into the molten slag bath to carry out combustion and reducing reactions."

Jan 1, 2012

By Teruo Tanabe

The hydrogen-absorbing materials are expected to have the following properties at moderate conditions, (a) a large capacity of hydrogen absorption, (b) the absorption rate of hydrogen is large and (c) hydrogen-absorbed materials can easily desorb hydrogen. Thus the three concepts of capacity, rate and reversibility seem to be indispensable to clarify the mechanism of hydrogen absorption by the materials. In this work, the amount of absorbed hydrogen, the absorption rate and the reversibility of hydrogen absorption- desorption reaction were measured for binary R-M systems (R = Y, La, Ce; M = Co, Ni). These experimental results were discussed by the following three physical properties that were calculated by the extended Hückel method, i.e. the density of states unoccupied by electrons, the cohesive energy and the energy fluctuation. The major results are as follows: (a) the amount of absorbed hydrogen increases with the density of states in the energy range between -9 and -4 eV, (b) the R-M compounds of which energy fluctuations are large show a large value of rate of hydrogen absorption, and (c) when the cohesive energy is large, the compound has a tendency not to easily desorb hydrogen, i.e. its reversibility is poor.

Jan 1, 2006

By Tao Li

The development of DP(Dual Phase) steels and TRIP(Transformation Induced Plasticity) steels has received much attention in recent years due to their high strength and simultaneous good ductility, which provides the potential for weight reduce and resource savings on certain components in automobile or other industries. So a controlled rolling process was simulated in the present study by thermomechanical simulator (Gleeble 1500) for producing DP steels on a kind of low carbon steel containing a small amount of Si and Cr. F+M dual phase microstructures have been obtained during continuous cooling processes of a wide cooling rate range from 10°C /s to 60°C /s. The grain size of the dual phase steel developed can be refined to less than 5 m through the mechanism of deformation induced ferrite (DIF) transformation. The ultrafine ferritic grains are equiaxed with high-angle boundary, and the martensite islands of an average size less than 5m disperse uniformly in the ferrite matrix. The ultrafine martensite islands not only inhibit the growth of ultrafine ferritic grains and improve the bonding of F/M interface, but also increase remarkably the strain hardening rate in the processing of the present Dual-Phase steel. As a result, the tensile strength of ultrafine grained Dual-Phase steel reaches higher than 1000 MPa. The result shows that an ultrafine grained Dual-Phase steel of low carbon and low alloy is promised to exhibit desired F+M microstructure by means of this new TMCP process.

Jan 1, 2006

By Mônica Suede Santos Silva

This work describes characterization of the performance of the tundish of a six strand continuous casting unit of the Companhia Siderúrgica Belgo Mineira, João Monlevade, Brazil using physical modeling. Permanent and transient conditions, due to ladle metal composition changes are considered. Pulse and step tracer addition techniques are employed to assess the control variables. For transient conditions the degree of inter-mixing and the minimum residence time are determined with a view to optimize the process especially during the grade changes of steel.

Jan 1, 2003

Novel techniques were developed to obtain samples from and make measurements in the shaft of the flash furnace at the Kalgoorlie Nickel Smelter. The data obtained was used to validate mathematical models of the burners and the reaction shaft. Particle, gas and wall temperatures were measured along with the oxygen potential of the molten particles. Collected particles were characterised by sizing, chemical analysis and optical microscopy. The region of the shaft immediately beneath the burner where the rate of change was most rapid received special attention.

Jan 1, 1993

By Eiichi Kuzuno, Atsushi Shibayama, Toyohisa Fujita, Kazuo Koike, Toshio Miyazaki, Hitoshi Masuda

"A solid sulfur is more useful to recover and store than a sulfuric acid as a by-product in the zinc hydrometallurgy. In this experiment a zin concentrate (sphalerite) was leached with ferric sulfate at about 373 K for 3 to 6 hours. Zinc was leached more than 95%. After a solid-liquid separation, the leached residue contained solid sulfur was obtained. The particles in the residue were dispersed by lignin and the solid sulfur of approximately 85% was recovered as float product by a flotation with frother in the pH 4. The dried float product was heated at 413K for 2 hours. The pure solid sulfur was recovered. On the other hand in the leached liquid a zinc oxide was ·added and ferrous .iron was oxidized to ferric iron by blowing oxygen. This ferric iron was returned to the zinc leached process after solid-liquid separation.IntroductionZinc concentrate is usually roasted as pretreatment in zinc hydrometallurgy and the produced S02 is changed to sulfuric acid. However, recently in Japan the utilization of sulfuric acid has been limited and it is more costly to store. Instead of producing sulfutic acid the solid sulfur recovery has been examined by direct leaching of zinc_ concentrate in this experiment.In the direct leaching, several kinds of effects have been studied for leaching of sphalerite in ferric sulfate solution. The addition of lignine siilfonate1 • 2) and fine· grinding3) increases the · speed arid leaching fraction of sphalerite. The leaching ratio depends on impurities in sphalerite ores4 • 5). Here, the zinc concentrate is leached ferric sulfate solution under atmospheric pressure at 373K. The solid sulfur in leached residue is separated as float products from other solids by sink-float separation and flotation. The sulfur in float products is purified by evaporation at 413K and recovered."

Jan 1, 2000

By Mokka Rao, Arturo Valles, Jose Rodríguez

"This paper shows a mathematical model based on finite elements, applied to bottom poured shell ingots of C.V.G. Sidor Plant. The model was used as a strategy to determine the thermal effects that are produced when solidification conditions are modified without interfering with the production process. The modification consisted of placing a thermal insulator on top of mould.The results obtained by the model indicated that the solidification time increases with insulator on base of the mould. With these results a significant number of casts were run with and without insulator. Latter by means of a metallurgical analysis it was determinated that the ingots cast with insulator reduce the level of non-metallic inclusions and the presence of internal blistering in seamless pipes.IntroductionThe process of fabrication of seamless pipes in SIDOR involves various steps of processing, such as heating the ingots, fabrication of the prelaminated, fabrication of the bored pipe, lamination of the pipe by passing through the pellegrine mill, heating the pipe in a walking bean furnace and final calibration through a calibrator mill. The material utilized for producing these pipes is provided entirely from a electrical arc furnace and casted ingots, especifically, from the superintendence of bottom pouring.The process of bottom pouring consists of positioning twelve moulds of diameters 415, 480 or 505 mm over a plate of grey cast iron in which exists a system of communicating vessels. The ingots are distributed around a central duct from which the steel flows down and filling gradually, each one of the moulds (Fig. 1)."

Jan 1, 1997

By Jian Li

Corrosion resistance of materials is highly dependent on the microstructure of the specific material. Apart from general corrosion rate measurement using techniques like linear polarization and A.C. impedance, microstructural investigations are frequently needed to identify the root cause of corrosion. Advanced techniques, including scanning electron microscopy (SEM) and transmission electron microscopy (TEM), have been well integrated into routine characterization studies. Other microscopy techniques, including electron probe micro-analyzer (EPMA), Auger, X-ray photon spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS), can provide detailed chemistry information on corrosion products. In recent years, focused-ion beam (FIB) microscopes have evolved into an important microstructural characterization instrument. In this study, corrosion of rebar encased in concrete was studied in great detail using advanced microscopy techniques. Corrosion product on the rebar surface was identified as ferrous oxide with relatively large crystal size. The morphology of this passive layer was thoroughly analyzed, and its formation mechanism is proposed.

Jan 1, 2009

By Donald I. Bleiwas

World primary nickel production in 1987 is projected to be 770,000 mt, slightly higher than that in 1986. Market economy country (MEC) production in 1987 is projected to be about 524,000 mt, an increase of almost 5 pct over 1986 production. Production cutbacks and closures at Japanese ferronickel plants in 1987 resulted primarily from the strong yen and higher energy prices. Cutbacks also caused reductions in ore production from Indonesia, New Caledonia, and the Philippines. Technical problems affected production, to varying degrees, in Botswana, Indonesia, and Yugoslavia. World primary nickel production for 1988 is projected to be 787,000 mt, of which 536,000 mt will be produced in MECs. Increased production is projected from Botswana, Canada, Cuba, and possibly Greece and Yugoslavia, while slight production decreases are projected for Indonesia, New Caledonia, the Philippines, and Zimbabwe. .. South African nickel production in 1988 could be severly curtailed by social strife. In the early 1990's Brazil and China could be major economic competitors to Western nickel producers.

Jan 1, 1988

By M. S. Lee

A cold model study on the effects of various operating conditions on the dispersed-phase holdup in a liquid-liquid emulsion generated by bottom gas injection has been performed using water and kerosene. Dimensional analysis was used to correlate the holdup with the operating conditions and the sampling locations. The holdup increased with gas velocity, and decreased with axial and radial distances. The radial distribution of holdup follows a Gaussian function. The holdup increased with increasing ratio of the heavy phase to light phase volumes and decreased with the total height of the heavy phase. The combined effects of various operating conditions can be represented by the Froude number. The variation of the holdup within the plume was correlated by a single equation involving a set of dimensionless numbers.

Jan 1, 1995

By Yasuhiro Konishi, Kazunari Mizoe

"This paper describes a new processing of ultrafine, magnetic ferrites from sulfuric acid pickling solution in steel industry. In the ferrite processing, the iron (II) in the pickling solution was first oxidized to iron (III) by using the acidophilic thennophile Acidianus brierleyi. The bio-oxidized pickling solution was treated with solvent extraction to separate the iron (III) into the organic solution of tertiary aliphatic monocarboxylic acid. After that, the carboxylate solutions of iron (III) and other metal (cobalt) were hydrolyzed and precipitated ultrafine particles of crystalline ferrites at l90°C and l. 3 MPa for 20 min.IntroductionHot-rolled steel sheet has always a layer of oxides on its surface. The oxide layer arises as scale in hot rolling processes in steel industry, and the scale consists of the three iron oxides such as hematite Fez03, magnetite Fep4, and wustite FeO. Pickling removes chemically the scale layer that adheres to the steel surface. For normal steels, pickling is carried out in 15-20% hydrochloric acid at 60-70°C or in 20-25% sulfuric acid at 95-100°C. When steel is pickled with sulfuric acid, the scale oxides dissolve to give iron (II) sulfate.Spent pickling solutions are hazardous wastes containing a large amount of dissolved iron (II) and sulfuric acid, e.g., about 40 kg/m3 of dissolved iron (II) at pH 0. In typical commercial processes, spent pickling solution is usually cooled evaporatively to 5°C, and then to 0°C to crystallize iron (II) sulfate as its heptahydrate. After the crystallization operation, the sulfuric acid can be reused in the pickling operation.In this paper we describes a new processing of ultrafine, magnetic ferrite from sulfuric acid pickling solution, in order to recover dissolved iron (II) in the form of a valuable product. In the ferrite processing, the iron (III) was first supplied by the microbial oxidation of iron (II) in the pickling solution, and then the biooxidized pickling solution was treated with solvent extraction to separate the iron (III) into the organic carboxylate solution. After that, the carboxylate solutions of iron (III) and other metal (cobalt) were precipitated crystalline ferrites under hydrothermal conditions."

Jan 1, 2000

By Asmo Vartiainen

The viscosity of liquid Fe-O-SiO2 -slag at copper smelting conditions was investigated using a rotational viscometer. The studied parameters were oxygen partial pressure (10" °-10"6 bar ); composition of slag (Fe/SiO2 ratio), and temperature (1250-1400°C). The viscosity values are presented as a function of Fe/SiO2 ratio and as isoviscosity curves in ternary FeO-Fe2O3-SiO2 diagrams. The increase in viscosity at high silica contents can be accounted for the polymerisation effect of SiO4/4- -anions. At high ferric iron contents, higher oxygen partial pressure, the viscosity values increase especially near the magnetite saturation. The viscosity values are highest at the double saturation of silica and magnetite. At lower silica and ferric iron contents the viscosity values are more uniform in the homogenous liquid slag area. The viscosity values were lowest at high temperatures and highest at low temperatures.

Jan 1, 1998

By I. Gaballah

High and low grade concentrates of tantalum and niobium oxides were obtained by leaching a medium grade tin slag. Chlorination and carbochlorinalion of these concentrates were studied between 200 and 1000 "C. Chlorination or carbochlorination of the low grade concentrate led, at 1000 OC, to the extraction of about 95 % of the tantalum and niobium oxides. However, the tantalum and niobium chlorinated compounds were contaminated by iron and manganese chlorides. Complete extraction of the niobium and tantalum pentoxide was achieved during the carbochlorination of the high grade concentrate at 300 and 500 "C, respectively. While chlorination of this concentrate at 1000 "C, allowed to the volatilization of about 60 and 80 % of Ta205 and Nb205. In both cases, condensates were composed of almost pure tantalum and niobium chlorinated compounds. The results demonstrate the advantages of the lixivialion based on the "pseudo- structure" of the raw tin slag to obtain the high grade concentrate. The conclusions of this work suggest that the carbochlorination of the high grade concentrate is an efficient process for the extraction of refractory elements from tin slag.

Jan 1, 1993

By Shufeng Yang, Anping Dong, Yongfeng Chen, Jingshe Li, Lifeng Zhang, Liyuan Sun

"Instead of nickel-based stainless steel, a nitrogen-bearing stainless steel was produced to reduce the production cost stemming from the shortage of nickel recourses. Thermodynamic model to calculate the saturation nitrogen content in the stainless steel were developed and the model was validated by experimental measurement. The experiments were performed with a high temperature induction furnace. Nitrogen gas under constant pressure was injected into the crucible with a top lance by which the nitrogen was transferred to the molten stainless steel. The effects of chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were investigated and discussed.IntroductionWith the rapid production growth of stainless steels, nitrogen-bearing stainless steel has recently attracted more and more attention for their high strength and excellent corrosion resistance imparted by interstitial nitrogen without decreasing its toughness and ductility. Moreover, the addition of nitrogen to the stainless steel as a substitute for nickel leads a lower consumption of nickel, so significantly lowers the high production cost stemming from the shortage of nickel recourses. However, production of the nitrogen-bearing steel is difficult since nitrogen is a gas element and has a low solubility in the steel. So efficiently increasing the amount of nitrogen in steel continues to be one of the main concerns for the production of nitrogen-bearing steels.Currently there are some special processes to produce austenitic stainless steels with a very high N content, including pressurized electroslag remelting, counter-pressure casting, special induction melting and powder metallurgy, etc [1]. Special expensive vacuum system was required for these processes. Alloying nitrogen at a normal pressure can be performed by alloy addition or gas injection. Blowing nitrogen gas is a more economic and advisable method since the nitrogen-bearing alloy is quite expensive and contains high content of impurities. A number of investigations have been reported on the solubility of nitrogen gas in pure iron [2] but few in iron-based multi-component alloys such as stainless steel.In the current study, the effects of steel chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were experimentally investigated with a high temperature induction furnace."

Jan 1, 2011

The 15m high Inco flash furnace uptake was designed as a reaction chamber with the objective of destroying the H2S contained in the furnace off-gas by combustion with oxygen at about 1300°C. Until recently, the oxygen required for this purpose was injected through afterburners located at the bottom of the uptake. An undesirable side effect of this practice was the formation of build up accretions on the inside walls of the uptake. This buildup had a negative impact on both the furnace on line time and the control of the flash smelting process. In late 200 I, the afterburners were relocated to the roof of the uptake. As a result, about 80% of the uptake accretion buildup disappeared with obvious beneficial effects for the operation of the furnace. This paper discusses key flash smelting aspects that affect the operation of the flash furnace uptake such as the dusting rate, the formation of H2S in the freeboard of the furnace, and the impact of using coke to supply some of the heat required by the process. The mechanism of buildup formation and its dependence 'on uptake afterburners location are also examined. Prof. Yazawa's sulfide smelting thermodynamic relationships proved instrumental in understanding the conditions that influence the formation and the elimination of H2S and uptake buildup.

Jan 1, 2003

By R. Padilla

Enargite (Cu3AsS4) occurs normally associated with copper sulfides, mainly chalcopyrite. When the enargite content in chalcopyrite concentrates is high, direct smelting of the concentrate presents problems related to environmental pollution and contamination of the final metallic copper. Leaching processes are viable alternatives to treat copper concentrates with high content of enargite. Consequently, in this paper, the pressure leaching of enargite in sulfuric acid-oxygen system is discussed. The leaching rate was studied in the range 160 to 220 °C and partial pressures of oxygen of 74 to 200 psi. The enargite dissolution increased substantially with temperature increase. Complete dissolution of enargite was obtained at 220°C, and 100 psi of oxygen pressure in 90 min. The shrinking core model controlled by surface reaction was used to analyze the kinetics of enargite dissolution. Activation energy of 70 kJ/mol was obtained for the temperature range 160 to 220 oC.

Jan 1, 2008

By T. Manlyama

The Tamano Smelter of Hibi Kyodo Smelting CO., Ltd. went into operation in 1972. The Flash Smelting Furnace that was originally adapted was equipped with electrodes that were attached to the settler substitute of the slag cleaning furnace. Later the development of our own original coke combustion technology was promoted and a new Tamano Type Flash Smelting Furnace (T-FSF), without electrodes, was put into operation in 1988, T he technology of coke combustion and combustion the burner have continued to improve. As a result the copper losses in the Wag have been reduced as well as a stable operation has been achieved, Furthermore; this has been accomplished while increasing the concentration feed and the matte grade. The current objective is to continue to strive for high matte grade operation and to raise production efficiency while paying attention to the important subject of copper losses in the slag. In this report, the data related to the copper loss in the slag reduction are presented along with the influence of the thickness, settling time and coke. The recent operation conditions of the T-FSF are also presented.

Jan 1, 2003

By Youn-Bae Kang

In order to overcome weak points of steel for its engineering applications, in particular, for environmentally benign, energy-efficient, lightweight engineering systems, a number of new steels have been proposed, especially to improve strength-to-weight ratio (specific strength). Mass production of these steels, however, has encountered a serious roadblock particularly in the steel refining and casting processes. This is because their chemistries and cleanliness requirements are vastly different from those of the conventional steels, and thus an incremental improvement of the prevailing process technologies is found hard to meet the requirements. In this study, a new process is proposed, which employs inert gas bubbles in the shroud nozzle, liquid steel drops in the degassing chamber, and the siphon transport for continuous casting. The proposed process which integrates the final refining and cleaning steps prior to casting is expected to be a technologically disruptive innovation on the conventional counterpart. The effectiveness of the individual steps is discussed with experimental results.

By Joo Hyun Park, Soo Sang Park

The distribution behavior of Pb between molten copper and FetO-SiO2 (-CaO, Al2O3) slags was investigated at 1473 K (1200 oC) and p(O2)=10-10 atm in view of the reaction mechanism of Pb dissolution into the slag. The distribution ratio of Pb (LPb) decreases with increasing CaO content (~6 mass pct) irrespective of Fe/SiO2 ratio (1.4~1.7). However, the addition of alumina into a slag with Fe/SiO2=1.5 linearly decreases the LPb, whereas a minimum value is observed at about 4 mass pct Al2O3 at Fe/SiO2=1.3. The log LPb continuously decreases with increasing Fe/SiO2 ratio, and the addition of Al2O3 (5 to 15 mass pct) into the silica-saturated iron silicate slag (Fe/SiO2 < 1.0) yields the highest Pb distribution ratio. The log LPb linearly decreases by increasing the log (Fe3+/Fe2+) value. The Pb distribution ratio increases and the excess free energy of PbO decreases with increasing Cu2O content in the slag. However, from the viewpoint of copper loss into the slag, the silica-saturated system containing small amounts of alumina is strongly recommended to stabilize PbO in the slag phase at a low Cu2O content.

Jan 1, 2014

By D. Georgiou

Direct sulphuric acid leaching of nickeliferous limonites is the process of choice to recover nickel and cobalt from equatorially located lateritic ores. These ores are rich-in-iron (-45 wt%) existing in the form of goethite enriched with nickel. The merit of this process is due to its high nickel selectivity because of simultaneous iron separation and acid regeneration. Under acid leaching conditions (-250 to 270°C) iron follows an acid dissolution-hydrolytic precipitation path yielding a very low concentration level depending on temperature and acidity of the final leach liquor. The primary precipitation product of iron is hematite which also forms as a scale on reactor internals along with co-existing aluminum. In this paper, an overview of the behaviour of iron solid products under process conditions is made. The evolution of goethite to hematite transformation, as well as the role of iron in reactor scale production, are studied using SEM/EDX characterization techniques.

Jan 1, 1995