Search Documents

By T. Goda, H. Kiuchi, M. Iguchi

"IntroductionThe utilization of silver in the electronic industry has been increasing in recent years. It is desirable that valuable metals are recovered from the used scraps of these industrial goods. Condensor chips, for example, contain silver, palladium, and Ag-Pd alloy. The dissolution behavior of silver was studied assuming that scraps such as used condensor chips in which Ag-Pd paste is used are subjected to wet treatment.ExperimentalIn this study the powder, granules, and flakes of silver were used in these nitric acid leaching experiments. The nitric acid solution was agitated in a glass reactor with a magnetic stirrer and heated to the required temperature. The experiment was started by putting the silver sample in the solution. After the leaching, the solution was filtered and the concentration of silver in the filtrate was analyzed by ICP.ResultsIn dilute nitric acid of less than 5 N, silver powder dissolved easily with increase in the concentration of nitric acid and temperature. However, the more intensive the stirring of the solution was, the lower the dissolution quantity became. Fig. 1"

Jan 1, 2000

By Carlos Carnurri

A characterization of mechanical properties of fire refined copper has been done in order to link ductility with oxygen content. The results show four different copper mechanical behaviours as temperature increases, where the oxygen con- tent, as Cu20 segregated, has a deleterious effect on ductility. It is concluded that until 500 ppm oxygen content, the fire refined copper could be rolled without remelting for deoxidation. Also a subsequent cold rolling could be done without intermediate annealing.

Jan 1, 1994

By June-Yong Eom, Jong-Jin Pak, Jung-Mock Jang, Min-Kyu Paek

The nitrogen solubility in liquid Mn-Si, Mn-Si-Fe, Mn-Si-C and Mn-Si-Fe-C alloys has been measured by the gas-liquid metal equilibration technique in the temperature range of 1673-1773 K. The additions of silicon, iron and carbon significantly decreased the nitrogen solubility in liquid manganese alloys. The experimental results were thermodynamically analyzed by the Wagner’s formalism to determine the first- and second-order interaction parameters of silicon, iron and carbon on nitrogen in liquid manganese. The thermodynamic parameters can be used to predict the nitrogen solubility in ferromanganese and silicomanganese alloy melts as functions of the melt composition and temperature at given nitrogen partial pressures.

Jan 1, 2014

By Hal dun Kurama

In thus-study, Bigadic upper zone zeolitic tuff, which contains about 87% clinoptilolite was used as an ion exchanger for removal of Pb++, Cu++, Cd++ and Hg++ ions from wastewater. Bench scale experiments with two different glass columns, were carried out continuously under the closed/ open circuit conditions. Before ion exchange tests, zeolite samples were treated with NaCI (6ml/ min. and 42BV). The effects of particle size, bed volume, pH and flow rate on the ion exchange capacity were determined. Under the best operation conditions, the effect of initial influent solution concentration on ion exchange selectivity was tested. As a-result, it was found that the Bigadiç clinoptilolite had the following ion exchange capacities;

Jan 1, 1995

By Michal Rehor, Vladimir Cablik, Peter Fecko, Tomas Lang

"1. Introduction The North-Bohemian Basin area is known for its largest Czech brown coal deposit. About 50% brown coal reserves have been exploited in the North-Bohemian Basin by the mining company of Severoceske doly, a.s. (North Bohemian Mines, j.s.c.) today. The opencast mining of brown coal naturally led to vast landscape damages. Therefore reclamation work has acquired great significance. The specific feature of Severoceske doly, a.s. mining is the fact that the mining has been realized in two geologically absolutely different localities. This fact demands even rather different methods of reclamations. The main problem at Doly Bilina localities is the occurrence of overburden rocks from the series of rocks of coal seams. These rocks are texturally light but large amounts of coal (cca 5 %) and sulphur (cca below 3 %) which makes the soil reaction extremely acid. If they appear on the surface of the dump, they create a phytotoxic area, reclamation of which requires special methods. Rocks from Doly Nastup Tusimice localities are more suitable to reclamation use, but texturally extremely heavy rocks with large fraction of physical clays appear there that can generate a sterile soil area. Their reclamation requirements are completely different from those on Doly Bilina phytotoxic areas. That is the reason of the application of some non – traditional restoration methods. This report briefly summarises the experience in application of fertilizable soils, power plant stabilizer, power plant ash and aerial sowing of charlock. The results are documented by the monitoring of the physical, mineralogical and pedological parameters of rocks in testing areas.2. Properties of Overburden Rocks in Opencast Mines Bilina and Libous The reclamation work methodology in the North Bohemian Basin is above all determined by the properties of overburden rocks which occur in the top horizon of the reclaimed sites. The research of the rocks reclamation properties dealt with four current mining localities in the central part of the basin. It concerned the Bilina and Libous mines. This chapter states the stratigraphic status properties of these sites with respect to reclamation availability. The total status of the area of interest is shown in the figure No. 1."

Jan 1, 2008

By Alessandra Bonoli, Garfìm Marianna

"Construction and demolition waste (CDW) is no dangerous material resulting from construction, and demolition of houses, large building structures, roads, bridges, piers, and dams. It is possible to recycle these materials, to reduce environmental impacts, and to reuse them in construction sector. To evaluate in a correct way the possibility to reuse this material it is important to lead laboratory tests to assess the proprieties and quality characteristics. European, Italian and British ad hoc Committees had elaborated specific Standards, to evaluate Geometrical, Physical, and Chemical requirements of recycled materials. A research was carried on to define the guidelines for laboratory tests, their suggested values and quality standards. The Construction and Demolition Waste Construction and demolition waste (CDW) is no dangerous, uncontaminated material resulting from construction, renovation, repair, and demolition of houses, large building structures, roads, bridges, piers, and dams. CDW waste is made up of wood, steel, concrete, gypsum, masonry, railway ties, roofing materials, carpeting, insulation, plaster, metal, and asphalt, and all waste included in CER Code 17. In particular Demolition wastes are defined as materials resulting from the demolition, instead Construction wastes are defined as waste materials resulting during construction process or in pre-manufacturing construction industry. Environmental problems In a lot of cases Construction and Demolition Waste materials were discharged in landfills, these are filling up with CDW and others, and some of them will close in the near future. In addition, illegal dumping of CDW debris can result in future health risks, decreased property values, cleanup costs and enviromental problems. The typical environmental impacts generated by CDW dumps are: 1- Dust problem, which causes air pollution, as will as forming dirty areas. 2- Uncontrolled locations, that will encourage the disposal of other waste types with the usual construction wastes leading to an environmental disaster. 3- The degradation and deterioration of the coastal lands and the natural protectorates. 4- The loss of aesthetic features. 5- Occupation of large areas, causing extra hauling costs. Therefore, it is wise to find other alternatives, like reuse or recycling, other than landfilling CDW debris or illegal dumps, because a proper management and the reduction of CDW amount can save money, conserve resources, and preserve the environment."

Jan 1, 2008

By Masayasu Kawahara, Toshiyuki Kozuka

"Lorentz force, which has the functions of wave suppression and mixing control, is very useful for many metallurgical processes. In this paper, it is found that vertical Lorentz force which can change 'the gravitational force is able to modify the dispersion relation of the surface wave generated by gravity and also modify the instability phenomena on the interface so that the lower layer can be scattered into upper layers to realize the strongly mixed region.IntroductionIn metallurgical industries, recently, a new direction of process developments is required backed not only by severer operating conditions, e.g. small amount production, rapid refining, etc. but also by environment and energy problem. Because almost technologies in conventional processes have saturated, an innovative process, which can break the limits in the conventional processes, is now strongly required. Especially, controlling of mixing phenomena between two liquid phases is considered to be one of the most important technologies for the promotion of slagrnetal reaction, wave suppression, etc. On the other hand, electromagnetic forces which have various functions have been applied to many processes. And Lorentz force is able not only to suppress the wave motion of molten _metal surface but also to promote the mixing or separation of two liquids. In this paper, new controlling methods of mixing phenomena between two liquids are proposed, where a direct electric current and a stationary magnetic field are utilized. Vertical Lorentz force due to the interaction between the electric current and the magnetic field can modify the gravity force so that the dispersion relation of surface wave and the instability on the interface can be change to improve or develop the innovative processes(l,2).In case that a direct electric current is imposed on two liquid layers with a stationary magnetic field, Lorentz force of each layer becomes different due to the difference of electrical conductivity. If Lorentz force acting on the lower layer is stronger than that on the upper layer, resonance frequency of the wave motion on the interface due to the gravity can be shifted from the frequency of a outer disturbance to suppress the wave motion. And also, the lower layer can be scattered into the upper layer as liquid particles by an instability phenomenon."

Jan 1, 2000

By I. U. Onyenanu, C. E. Ilochonwu, E. I. Nwonye, C. O. Nwajagu

This work shows how pure silica was derived directly from rice husks ash (RHA) in different temperatures for reduction to Silicon (Si). The processes to form Si materials are usually complex, costly and energy-intensive. The silica in the ash undergoes structural transformations depending on the conditions of combustion. A high purity silica was produced at 650oC after burning the rice husk (RH) for up to 7 hours. The purity of the silica was determined by dissolving the RHA with alkali solution to form sodium silicate solution of pH 11.0. This was added to hydrochloric acid of pH 1.5 which lowered the pH of the solution to 4.0 to form silica gels. The silica gels produced were washed and dried to powder and then characterized using XRD and EDX techniques. This study was done to reduce energy waste and environmental pollution in Nigeria as silica is used to develop many materials.

Jan 1, 2015

By Eugene Jak

Copper sulphide processing technologies face increasing pressures associated with decreasing concentrate grade leading to increasing thermal inefficiency and lower productivity. Impurity concentrations are on average increasing, creating potential environmental risk and additional treatment costs. In copper flash smelters dust, partially oxidised materials and fume formed from the condensation of volatile impurities, are routinely recycled to the feed. In the converting stage the heat balance is maintained by charging anode reverts and other inert materials. In both cases, the thermal energy available from sulphide oxidation is not fully utilised or optimised. The productivities of both smelter and converter stages can be potentially increased through the addition of a high copper, low iron, low impurity precipitated copper product. Calculations are carried out for fayalite smelter and calcium ferrite converter slags using an optimised FactSage thermodynamic database. The potential for significant increases in smelter and converter productivities using existing technologies are predicted.

By Anurag Tripathi, J. K. Saha, S. K. Ajmani, J. B. Singh

"The quality of steel is a major concern in the metallurgical industry. The control of liquid steel temperature can enhance the level of cleanliness in steel. Ladle is one of the major vessels used to transfer liquid steel between different stations. The heat transfer phenomenon taking place in this vessel needs to be monitored for controlling the liquid steel temperature. A CFD model was developed for prediction of liquid steel temperature during complete process cycle of ladles in direct heats. The model was validated with liquid steel temperature measured at on-line purging station and tundish during teeming from one of the actual steel plant. The accuracy of model was 96 %. The results obtained show insignificant effect of slag thickness, tapping temperature and ladle life on liquid steel temperature in the ladle. However, the importance of initial refractory temperature was noticed. The CFD model developed in present work can generate the thermal history of liquid steel and refractory walls of any ladle at any stage.1. IntroductionThe control of liquid steel temperature is desired to achieve required steel quality. The low casting temperature is detrimental and may result in nozzle blockages due to premature solidification in the tundish. The phenomenon of heat losses taking place in ladles needs to be understood for prediction of liquid steel temperature. The assessment of thermal profile of liquid steel from BOF converter to caster can be done through consideration of heat losses at all points. Hlinka and Miller [1] showed that the ladle pouring temperature varies due to heat losses from molten steel into surrounding refractory layers. The phenomenon of thermal stratification was numerically simulated by Ilegbusi and Szekeley [2]. The effects of slag cover on heat loss and liquid steel flow in ladle before and during teeming to a continuous casting tundish was numerically simulated by Chakraborty and Sahai [3]. Investigators also developed some simple models to predict the steel temperature for some of the processes taking place in ladles [4-9].The present work is an effort to generate the full information about the temperature drop taking place in any ladle throughout its process cycle. This information can be used to predict liquid steel temperature and to take decisions to minimize heat losses."

Jan 1, 2012

By Magdelinka Padenkova-Yaneva, Emilia Christova Kostakeva

"Environmental protection is becoming over the years an increasingly significant problem of mankind. Up to the last decade the only way to make the domestic waste harmless in Bulgaria was deposition on uncontrolled landfills without undertaking actions for protection of the soils. This also caused pollution to spread into the surface and underground waters and that is why actions are now undertaken for remediation of contaminated soils. This is achieved by developing projects for the closing down of polluted sites. In the present paper some projects for closing down of polluted areas are discussed. The actual conditions are examined and project decisions for preventing the surface waters from penetrating into the waste are presented. In this way the pollution of the soil is stopped and the soils are gradually remediate.IntroductionSoil is the topmost layer of the earth crust. It consists of mineral particles, organic substances, water, air and living organisms and is an extremely complex and changing living environment. Soil is a non-renewable natural resource which is of considerable importance in a number of crucial processes (production of foods, storing, filtrating and turnover of many substances, including water, carbon and nitrogen). It also serves as a basis for human activities, shaping the landscape, ground on which cultural heritage is built, and source of raw materials. These functions of soil must be protected both because of their social and economic significance and from the point of view of environmental protection.The processes of erosion, loss of organic substances, compaction, salination and contamination contribute to the degrading of soils accompanied by a negative impact on human health, natural ecosystems and changes in climate, as well as on the economy. All these make it necessary to protect soils from contamination. Over the last years intensive work started in Bulgaria for the construction of controlled sanitary landfills for rendering municipal solid waste harmless. Pursuant to Bulgarian legislation, in these controlled sanitary landfills measures are undertaken for protecting the soils from contamination through appropriate project decisions – the filtration of the products from the biological decomposition of waste into the adjacent sites (soils) and, therefore, the contamination of the surface and underground waters is prevented. At the same time the purity of air is maintained, human health is protected and conditions are created for including the controlled sanitary landfills into the surrounding landscape."

Jan 1, 2008

By Rumen Markov, Lubomir Kuzev

"The treatment technologies for municipal solid waste (MSW) are effective mainly for components sized over 40 – 50 mm. This fraction is separated by screening in the beginning of the process. Usually the undersized product is deposited without additional treatment. Its quantity is variable from several up to 30 – 40 % of the total MSW. Both oversized and undersized fractions are formed by all types of primary matter. Adapted technologies from mineral processing will provide a suitable technology for treatment of MSW under 40 – 50 mm. The MSW content depends on the geographical location, the degree of urbanization and other factors. The methods can be applied for separations of different components suitable for recycling or other utilization are: • Separation by density; • Separation in thin liquid layer; • Selective grinding and screening; • Flotation, etc. Introduction Municipal solid waste (MSW) represents an integral part of public urbanization. However, there are some drawbacks stemming from MSW, in regard to its collection, transport and elimination. Different approaches exits worldwide for tackling the problems arising from MSW. For a short period of time, the attitude towards MSW has evolved in several levels, each further level being characterized by higher percentage of utilization of MSW components. Thus, the bottom line has been shifted from safety storage towards processing that includes recycling and maximal utilization of MSW components. Technologic processes applied for treatment of MSW have a common feature – that the fine components, having sizes under 20 mm, 30 mm, 40 mm, or 50 mm are excluded from treatment process trough screening, and in most cases diverted without any additional treatment to preliminary prepared storage sites. MSW in Sofia – current situation The amount of MSW collected daily in Sofia as around 1000 t/24 h. It is stored or baled. Baling is a spare alternative of storage, since baling insures only temporal keeping of MSW, till the building of suitable storage site where the bales will be transported and buried. The morphologic composition of MSW in Sofia has been determined several times at different time intervals, from some Bulgarian organizations as well as from the Japanese organization JICA. So far, however, there is still a lack of enough systematical and comprehensive study. Generalized results from the studies on the MSW components, as well as some important parameters are given in Table 1."

Jan 1, 2008

By Lan Li, Izaak Williamson

"The efficient separation and storage of CO2 from power plant flue gases can reduce the amount of CO2 released into the atmosphere and mitigate global warming. Potential candidates for industrial applications are solid sorbent materials. Crucial factors to control the efficiency of porous sorbent materials include the framework and pore structure, and the chemical and physical reactivity of CO2 within the pores. Computational modeling approaches, based on density functional theory (DFT) and van der Waals-DFT, have been applied to nanoporous solid – manganese dioxide a-MnO2. We found that the types and charges of cations as dopants in the a-MnO2 and the concentration of CO2 influence the structural features of a-MnO2, which control its CO2 selectivity performance within the flue gases.IntroductionCarbon capture and storage is a technique to separate large quantities of CO2 from power plant flue gases before being released into the atmosphere. Porous solids are a potential candidate as sorbents to “trap” CO2 through chemical or physical adsorption on their porous surfaces[1]. Such separation efficiency is determined by the size and shape of its pores and by the interaction between the porous surface and the gas adsorbates. The incorporation of cations into the pore can act as a means of structural support and alter the pore diameter to be comparable to the kinetic diameter of the gas adsorbate, such as CO2.A porous solid of particular interest for CCS is manganese dioxide a-MnO2, an octahedral molecular sieve (OMS) composed of edge-sharing MnO6 octahedra that are linked into a nanoporous framework[2]. The framework consists of (1×1) and (2×2) tunnels, referred to as OMS-2. Due to the larger tunnel size, cations and gas adsorbates prefer to reside along the (2×2) tunnel axis of the OMS-2. As seen in Figure 1, a potassium cation K+ is located in the (2×2) tunnel, known as cryptomelane-type MnO2. Its pore diameter of ~ 4.6 Å gives it a good CO2 selectivity performance, because the diameter is comparable to the kinetic diameter of 3.3 Å for CO2[3]. Alternatively, replacing potassium K+ with other cations, e.g. barium Ba2+, sodium Na+ or lithium Li+, in the OMS-2 tunnel is of great research interest, due to the effects of their concentrations, types and charges on the CO2 selectivity efficiency and sorption hysteresis phenomenon[2,4]."

Jan 1, 2014

By Zhi-gang Que, Sheng-li Wu, Guo-liang Zhang, Bo Su, Chao-gang Hou

NOx released during fuel combustion is one of the major air pollutants, such as acid rain and photochemical smog. At present, still not have an economical and effective method of inhibiting NOx emission for sintering flue gas. Therefore, controlling conditions of fuel combustions to enhance the reduction of NOx is important for decreased the emission. In this study, microsintering furnace has been performed to investigate the effects of NOx emission from char-N during coke breeze combustion. The results show that the emission concentration of NOx decreased with increasing temperature when it is sinter bed temperature higher than 1000℃. The lower emission concentration of NOx was obtained when the concentration of oxygen was decreased. And the maximum concentration of NOx will be reduced with the enhanced of heating rate. If heating preservation time was prolonged, it would promote to NOx reduction with reduction substances resulted in lower NOx emissions in the combustion of coke breezes.

Jan 1, 2015

By Ronald H. Church

Dewatering of mine waste slurries has been successfully accomplished by the proper use of polymers in flocculating the fine particulate matter suspended in the slurry streams. Conventional treatment of fine waste slurries usually involves some form of impoundment treatment or storage. These impoundments present unique environmental problems. When filled to capacity, the impoundments are usually unloaded with a dragline and transported to a separate disposal area. The U.S. Bureau of Mines has conducted dewatering studies utilizing polymer technology in combination with a mobile field test unit designed by the Bureau. The purpose of these studies was to determine if the fine waste slurry from the mining operation could be successfully dewatered. Results of the investigation have shown that the slurry can be dewatered successfully. The dewatered products obtained from the tests ranged from 45 to 50pct solids. This material continued to dewater, approaching 70 pct solids within 24 h, and could be easily handled using conventional transportation equipment including conveyor belts.

Jan 1, 1994

By Shaolong Chen, Carl-Gustav Berg, Hannu Mansikkaviita

Kumera Steam Dryer has been developed particularly for nonferrous metal concentrates with steam as heating source generated from waste heat boilers. Its unique structure enables the dryer to work at high capacity, up to 240 t/h, and high availability, over 95%. With half a century of engineering experience, and more than twenty industrial steam dryer installations worldwide during last 15 years, Kumera has demonstrated significant benefits of the steam drying technology in terms of energy efficiency and emission reduction to the end users. The dryer of this type can also be applied for other suitable mineral materials.

Jan 1, 2015

By Xiangru Chen, Qijie Zhai, Haicheng Li, Chao Yang, Zhang Wei

The Nb-rich phase generated by the addition of trace amounts of Nb(<0.1wt%) \ and the effects of different content of Nb on the morphology and distribution of graphite in ductile iron were studied in this paper. The results showed that when the content of niobium less than 0.1wt%, the two-dimensional morphology of Nb-rich phase existed in microalloyed ductile iron were mainly regular pattern such as square, triangle, polygon etc. Besides, Nb-rich phase in large size distributed in the matrix with a certain distance from graphite. With the increasing amount of niobium, the dispersion degree of graphite diameter, average diameter and roundness increased slightly, and the number of graphite decreased slightly.

Jan 1, 2015

By M. A. Llavona

In Spain, as in many countries, the gold content of jewellery must be officially hallmarked. The official methods of assay are gravimetnc cupellation (a method which is highly accurate but both time and sample consuming), potentiometry, gravimetry and volumetry. In this paper, a procedure for measuring gold by flame atomic absorption in jewellery samples is described. The method is based on the acid digestion of a 40 mg sample. The quantity of aqua regia necessary for dissolving the gold, the ideal weight of a sample in order that the error may be minimal, the effect of the acids employed, the type of material used for its storage, and the necessity of employing a buffer to avoid the ionization of the solution are described. The method proposed is simple, highly accurate and causes little damage to the jewellery.

Jan 1, 1999

By Wenying Liu

The effect of aeration on chalcocite heap leaching was studied by analyzing the historical data from two chalcocite heap leach pads located in Chile, one with aeration and the other without aeration. The data showed that the copper leaching kinetics of the aerated heap was greater than that of the unaerated heap within a certain leaching period, after which there was no effect of aeration on the copper leaching kinetics. The total acid consumption per ton of ore processed was higher in the case of aeration, which was supported by the higher pH of the PLS. But the net acid consumption per ton of copper produced was the same in the two cases. Approximately 5% of the total iron added to the unaerated heap was precipitated inside the heap. In contrast, there was no net iron precipitation or generation inside the aerated heap. Bacteria activities were thought to occur even in the unaerated heap, but the extent was much less than in the aerated heap. Given the importance of forced aeration in chalcocite heap bioleaching, mathematical modelling will be applied in the future work to assist the optimization of the aeration system design.

By Enrique Posada

"The Valle de Aburrá area, corresponds to the city of Medellín and neighboring municipalities, with more than 3 million people. The area generates a sizable amount of solid waste, which has been taken to landfills for the last 20 years. This paper proposes a model for public policy making which considers the cost and benefit of different alternatives to handle the wastes in the coming 20 years. Combinations of several alternatives: Recycling, waste reduction, waste separation, incineration, land filling with lixiviate treating and gas energy recovery, and organic waste composting are considered and modeled and the results presented as a contribution for a more rational approach to policy making than the one currently being employed.IntroductionThe author, working for INDISA S.A., acted as a consultant for the direction of planning of the Empresas Varias de Medellín in 2004. This entity has the responsibility for the handling of the solid wastes of the city of Medellín and some of the neighboring municipalities. At the present time more the 700.000 annual tons of waste are taken to the site of La Pradera, located in very rainy location (3.000 mm of precipitation per year), with complex in topography and very far away from the sources of the waste. During the work the author detected important problems that should be addressed, as follows:Lack of adequate technical administration and resources. The entity did not count with sufficient human resources to focus on the appropriate technical handling of the solid waste. The organization worked mostly with independent contractors, lacking enough coherence and integration. The internal workload was too large for the few people who had technical responsibility and this gave rise to attention problems. It is important to have clear technical procedures, technical know how and human resources, continuity in the activities. It is important to have a clear capacity to plan, to study, to make tests and monitoring, to pursuit and develop ideas, to optimize the processes and to introduce changes, to respond to environmental authorities, to the communities and to mass media and to handle the contractors. All this was basically lacking. In the case of the handling of the sanitary filling of La Pradera, for example, although the people in charge were very able and dedicated, the magnitude of the task was too large and the resources they had were insufficient. As a result, the site had at the time of the study, problems with thousands of vultures, lack of immediate cover up for the waste, uncontrolled leaching, the area being dirty and little attractive, despite being called a park."

Jan 1, 2008