Search Documents

By Hans-Christian Kurzweil, Klaus Mussger

CERN, the European Laboratory for Particle Physics, are upgrading their existing particle accelerator for the next generation of experiments and have three major packages of underground construction work in progress. Each package involves the construction of shafts, cavern, tunnels and surface buildings. This paper gives an overview of CERN, the LHC Project and a more detailed discussion of design process, design review and construction works of Experimental Point 5. The LHC works at Point 5 include two large shafts, two major parallel caverns with a total span of 50 m, which are separated by a 7 m wide and 28 m high concrete pillar, and a system of secondary tunnels and caverns. The overburden ground consists of around 50 m of water bearing moraine (silty, clayey gravels and sands) overlying 20 mof molasse, which consists of horizontally bedded marls and sandstones. The shaft shave been constructed with ground freezing, primary concrete lining, membrane and secondary slip formed concrete lining. The concrete pillar was then excavated and concreted in advance of excavation of the two caverns. Cavern construction includes primary support of shotcrete lining and rock bolts, followed by waterproof membrane and primary support of shotcrete lining and rock bolts, followed by water proof membrane and insitu concrete secondary lining.

Jan 1, 2003

By D. Hong, K. N. Han

The leaching behavior of rhenium in ammonium iodide solutions with iodine as oxidant was studied. Experiments were carried out in an autoclave to investigate the effects of stirring speed, temperature, solution pH, and iodine and iodide concentrations on the dissolution of rhenium. It was found that a high temperature and a high solution pH were essential for the efficient leaching of rhenium. The dissolution rate was found to be dependent upon the concentration of iodine and iodide. It was concluded that the dissolution of rhenium under the conditions studied was controlled by the mass transfer of iodine with an apparent activation energy of 15.8 kJ/mole.

Jan 1, 1999

By H. Wu, V. Izaxon

Intensive ventilation is required during the excavation of a mine opening and the subsequent exploitation of the mineral resources. The exchange of heat between the ventilation air and the rock mass has a major influence on the thermal regime of a mine, especially in the initial segment of the airway. In frozen ground, heat flow into the rock mass from the ventilation air can result in the eventual thawing of the permafrost, which can result in roof-rock instability. This paper presents a mathematical analysis of the dispersion process of ventilation-induced heat by thermosyphons placed on the surface of the mine. The principal uses of thermosyphons in the Arctic are to reduce the ground temperature to prevent potentially unstable permafrost from thawing and to increase the bearing strength of the material. The mathematical model of the physical problem, generally known as "the Stephan problem," takes into account the varying thermo-physical properties of air and the frozen and thawed rock mass, the thermal properties of the freeing fluid in the thermosyphons and the phase change of water. Finite-difference techniques were employed to determine the temperature isotherms around the thermosyphons. It was found that two rows of thermosyphons on a 10- x 10-m grid provide an acceptable design spacing for reducing the ground temperature around the mine airway.

Jan 1, 1997

By Clinton Strachan, Dirk J. A. van Zyl

11.1 INTRODUCTION This chapter outlines some of the selection and design considerations for leach pads and liners. Leach pads and liners are generally chosen to provide the required or desired levels of low permeability and foundation conditions at minimum cost. The selection and design of a particular liner depends upon its anticipated use and performance, and what materials may be available. A leach pad is the firm base for a heap. When geomembrane liners are used, the pad is the firm, compacted foundation upon which the liner is placed. In the case of a clay liner, the clay liner is usually also the pad. It is important to consider the design of a pad or liner in terms of a system. The "leach pad system" consists of the prepared foundation, bedding layer (if used), liner (s), seepage collection or detection layer (if used), and cover layer. Foundation preparation is necessary to ensure a stable base for the rest of the leach pad system. A bedding layer is used to protect a liner from being punctured by large angular fragments in the foundation material. A seepage collection or detection layer, consisting of well-drained material and (sometimes) pipes draining to a collection sump, is included when a double liner is used. A cover layer on top of the liner can serve the following purposes (van Zyl and Strachan, 1986): • Preventing of ultraviolet light exposure to sensitive geomembranes; • Limiting evaporation from compacted clay liners and thereby eliminating cracking of such liners; • More efficient collecting of leachate; and • Protecting the liner from damage during heap construction. Economic evaluations of alternative liners for a project must include the overall system. For example, a geomembrane liner may require different foundation preparation and cover material selection and placement than a clay liner. Liners can be made of compacted clay onsite, amended soil, or geomembranes. Geomembrane is a generic term that has been proposed to replace many terms, including synthetic membranes, polymeric membranes, plastic

Jan 1, 1988

By Arthur R. MacPherson

Este capítulo revisa las etapas que deben seguirse desde el momento de considerar la molienda autógena en el desarrollo de un nuevo depósito de mineral o en la expansión de una planta existente, hasta la compra de un molino autógeno. En este caso el término autógeno incluye: semi-autógeno, molinos de pebbles secundarios y molino de bolos (trozos), así como los sistemas de molienda autógena total. También se han incluido las alternativas por vía húmeda y seca. Antes de programar el ensayo debe decidirse cuantas muestras brutas son requeridas para calcular propiamente las posibilidades de molienda autógena del depósito. También ha de tomarse la decisión, de como y donde deben tomarse las muestras, por ejemplo: planta piloto situada en el sitio de localización de la planta o en otro lugar establecido; molienda en húmedo y/o en seco....etc. En el mismo programa del ensayo se obtendrán ciertos datos fundamentales. Los ensayos deberán incluir un trabajo suficiente. para determinar cuál de las moliendas, totalmente autógena o semi-autógena, debe utilizarse; y qué tipo produce la máxima eficacia en la potencia consumida. También, los otros datos pertinentes deben ser recolectados, como por ejemplo: potencias, tonelajes, alimentación, carga, tamaño del producto, carga circulante, etc. Si es necesaria una molienda secundaria para obtener el tamano final, la decisión de qué molienda debe emplearse (molino de pebbles o molino de bolas) puede requerirse un ensayo de trabajo adicional. Finalmente, la concentración del mineral puede jugar un papel importante en la selección del circuito y debería ser una parte del ensayo final una vez que se ha establecido la molienda. Para determinar qué tipo de molinos pueden satisfacer los requerimientos establecidos por la planta piloto, debe tomarse una escala para ciertos datos como: potencia del molino, consumo de acero, simple o doble etapa de molienda, tipo de molino secundario. Para asegurar un posterior entendimiento del depósito de mineral y sus características de molienda, deberán efectuarse algunos trabajos adicionales a pequena escala utilizando pequeñas muestras y molinos para producir unos datos comparables de molienda. También, algunos ensayos tales como medio de molienda óptimo, e índice de trabajo, deberán ser completados.

Jan 1, 1982

By Jean E. Kiel, Rob Dorey, Dirk J. A. van Zyl

1.1 INTRODUCTION This chapter seeks to provide an overview of important factors involved in the implementation of heap leach technology as a vehicle for gold extraction from its ores. Toward this end, brief discussions of the various elements important to this process are presented here. Topics covered in this chapter include a brief history of the process; basic chemical reactions responsible for the process ; characteristics of ores amenable to heap leaching; location of the greatest concentration of heap leach projects in the U.S.; heap leach components, methods, regulatory/permitting considerations; and economic considerations. Most of these subjects are treated at much greater length in subsequent chapters. Thus, this chapter serves as a summary for those which follow, in addition to providing the reader with a feeling for those topics which may be of most immediate interest. 1.1.1 History of the Process Modern Day Precious metal heap leaching technology has developed over the past decade, although the principles of heap leaching per se, as well as those of gold extraction through cyanidation have a long history (see discussion below). However, it is in the past 10 years that heap leaching has developed into an efficient method of treating oxidized gold and silver ores. It has proven to be both an efficient way to extract precious metals from small, shallow deposits, as well as an attractive way to treat large, low- grade, disseminated deposits. Heap leaching has several advantages compared to conventional milling (i .e., crushing, grinding, and agitation leaching). In general, these advantages include simplicity, lower capital and operating costs, shorter start-up times, and less intensive environmental regulatory concerns. A possible disadvantage of currently existing heap leach technology is a potentially lower percentage of metal extraction being obtained from the ore than would be the case with conventional milling (Potter, 1981; Hiskey, 1985; and Thorstad, 1987) The actual principle of heap leaching has a long history as inferred previously. For example, mines in Hungary recycled copper-bearing solutions through waste heaps in the mid-sixteenth century (Hiskey, 1985), and Spanish miners percolated acid solutions through large heaps of oxide copper ore on the banks of the Rio Tinto around 1752. By 1900, leaching operations were employing such techniques as leach/rest cycles to maximize copper recovery (Taylor and Whelan, 1942; Thorstad, 1987). Copper dump leaching is currently

Jan 1, 1988

By Moussa Wone, V. Nasri, F. Guimbal, D. Andre

The Magenta underground station was constructed in the heart of Paris in saturated soft soil and at shallow depth. To investigate the surface settlement and the deformation of the concrete liner, innovative techniques combined with a vast campaign of monitoring were applied. The monitoring data and a simple three-dimensional ?nite element analysis were used to assess the accuracy of the two-dimensional ?nite element model originally utilized in the design of the station. The deformation of the concrete liner was monitored using vibrating wire extensometers. Their performance was validated by the data obtained from monitoring and also by a simpli?ed ?nite element analysis.

Jan 1, 2003

By D. R. Dolinar, J. Pablic, D. C. Oyler, T. P. Mucho

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the "advance and relieve" method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

Jan 1, 2001

By A. E. Isaacson, D. B. Dreisinger, G. A. Kordosky

The U.S. Bureau of Mines is researching the application of solvent extraction technology to highly acidic (pH < 1) copper leach liquors. As increasingly complex copper ores are mined for leaching, use of highly acidic leach solutions maybe necessary to effectively recover the contained metal values. A mixture of two commercially available extractants, based on aldoximes and substituted 8-hydroxyquinoline, which has a high transfer efficiency has been identified. A synthetic leach liquor, containing 5 g/L Cu at pH 0.9 was processed utilizing the mixed extractant and a laboratory SX circuit. The loaded organic was stripped with a synthetic barren electrolyte compatible with electrowinning technology.

Jan 1, 1993

By M. Poulton

Backpropagation, learning vector quantization, counterpropagation, functional link, probabilistic, and. self -organizing map are among the most popular neural network classification paradigms. Each paradigm finds a unique set of weights that will map the input pixels into their respective output classes. The usefulness of each network depends on its overall accuracy, ease of use, speed and scaling. The fastest and most accurate networks in this study were the functional link and counterpropagation. These networks, however, do not scale well to large input vectors or large training sets. A better choice is the LVQ network which achieves high accuracy, is fast, requires a minimum number of input parameters and presents fewer scaling problems.

Jan 1, 1992

What is your assessment of the current state of the minerals industry? It is no understatement that domestic mining is facing a severe crisis at this time. The sharp decline in commodity prices and demand is putting a great strain on domestic and worldwide mining, causing major declines in profits and market capital of mining companies. This, in turn, has lead to major production cuts, layoffs, shut-downs of operating properties, and the deferral of new and expansion projects. These changes in the minerals industry have played a major role in the health of the economy. Operationally, the industry continues to develop new technologies that are making our work more efficient, more cost effective and more environmentally acceptable and safe. During downturns like this, companies generally pay closer attention to operational efficiencies and process optimization. Historically, new technologies and processes tend to be developed during down markets, and I believe we will see the same thing as companies strive to preserve liquidity and maintain or improve their margins. On the positive side, the drop in commodity prices has resulted in a reduction in operational costs, as the costs for fuel supplies and construction materials have decreased.

Jan 1, 2009

By Thomas Schultheis, William Heron, Paul Watson, Colin Warren

This paper describes the geology and geotechnics associated with construction of the Thames Tunnel, part of the UK’s Channel Tunnel Rail Link (CTRL). The 2.5km long twin tunnels run beneath the river Thames at depths of up to 40m and are currently under construction. They pass through varying geology comprising alluvium, terrace gravels and chalk with flints and are currently being bored using Herrenknecht mixshield slurry tunnel boring machines (TBM’s). This paper outlines the lithology and engineering properties of each geological formation and describes the geotechnical processes, potential hazards and difficulties experienced in the works. A summary is given into the extent of the investigative work in terms of route selection, tunnel design, TBM optimisation and further details are provided on the geotechnical aspects associated with the construction of the tunnel approach structures and the tunnels.

Jan 1, 2003

By Qiu Rongqing, Huang Kongxuan

This paper summarizes the results of treating arsenic­bearing refractory gold concentrates from six gold Mines of Chi­na by using bioleaching method and discusses the conditions of bioleaching processes. Results indicate that Thiobacillus fer­rooxidans T-3 Strain can intensely oxidize arsenopyrite, how­ever oxidation rate and degree differe considerably for different. During initial inoculation of 5 X 106 cell/ml. FeH contration generaly 4 -8 g/1. Sample size > 80 % - 3 20 mesh and pulp density 10 % ( w /v) and leaching time ,1 -- G clays, arsenic re­moval rate reached more than 80 % , Fe extraction ,10 - GO% desulfurization rate 30-45% after bacterial oxidation of 4-G days.

Jan 1, 1992

By H. J. Ilgner

Previous applications for using waste rock for backfilling in South African gold mines were reviewed and it was found that in many cases the mechanical equipment selected and the design philosophy applied did not meet the requirements. A more simplified system configuration is proposed, which allows the equipment to be relocated as mining progresses. Innovative high-intensity grinding and dense-phase pumping technology are proposed to provide a low-porosity backfill with a particle top size of 5 mm to 8 mm. According to recent rock mechanics modeling work, this comminuted waste backfill material can provide a good compromise between underground support characteristics and reliable hydraulic transportation behavior.

Jan 1, 2001

By Jozef F. Zurawski

The paper discusses design and construction of a 1.8 meter (6 ft.) diameter tunnel installed under complex geology of Staten Island, New York. Contract T-13 is a section of the Oakwood Beach Water Pollution Control Project constructed for New York City Department of Environmental Protection. A knowledge of the subsurface conditions and difficulties experienced on the adjacent contracts called for an innovative approach to handle tunneling under 12 to 17 meters (40-55 ft.) of water in the variable subsurface conditions. This paper describes tunnel design and construction utilizing continuous grouting during advancement of tunnel boring machine and installation of liner plates.

Jan 1, 1993

By P. R. Busmann, D. J. Rogers

The Bureau of Reclamation&apos;s Syar Tunnel project included excavation of a 9.2 kilometer (5.7 mile) long, 3.6 meter (11.8 ft) diameter tunnel through gently dipping sedimentary rocks consisting of shales, siltstones, sandstones and limestone. The tunnel was supported full length with precast concrete invert segments and lightweight steel sets and lagging. Several world records for advance rate were set, including 57 meters (187 ft) in an eight hour shift and 127 meters (417 ft) in a 24 hour day. The tunneling system utilized a remanufactured and modified Robbins hardrock TBM and a 9,280 meter (30,450 ft) long, 61 centimeter (24 inch) wide, continuous conveyor system.

Jan 1, 1991

By Mulong Yu, Yosry A. Attia

Beneficiation of high magnesium Florida phosphates requires ultrafine grinding to liberate the dolomite (the main source of magnesium), and a separation process capable of dealing with ultrafine sizes such as selective flocculation. The objective of this study was to investigate the feasibility of separating dolomite from apatite ultrafines by selective flocculation. To achieve this objective, selective polymeric reagents to either dolomite or apatite must be first designed and synthesized. This challenging task was accomplished by carefully selecting complexing/chelating agents which are selective to either the Ca or Mg ionic sites on the minerals, and incorporating these reagents into the structure of long chain water soluble polymers to obtain either selective flocculants (with high molecular weight, MW, polymers), or selective dispersants (with low MW polymers) to either the dolomite or the apatite particles. Synthesis and testing of these polymers on individual and mixed mineral slurries, and on a sample of natural high magnesium phosphate ore, have been attempted and the results are described in the paper. The preliminary results showed encouraging signs for the feasibility of selective flocculation separation of dolomite from apatite.

Jan 1, 1993

By Pierre Ollivier, Dominique Morin, Pr. Ivo Toromanoff

Refractory gold ores have been processed by bio-hydrometallurgical process at B.R.G.M. (Bureau de Recherches Géologiques et Minières), Research Centre ,Orleans,France. The liberation of gold has been studied and the following steps for gold recovery improved. The overall process flowsheet has been established comprising different ways of treatment before the final discharge of the effluent. Iron and arsenic are successfully precipitated under well controlled Eh-pH conditions. Long term stability tests have been conducted and the research programme is to be continued with the crystallo graphic studies of the precipitates. Economical studies have been performed on the base of data obtained on parameters studies.

Jan 1, 1990

By Armando Alatorre

The Republic of México is the world&apos;s largest producer of celestite/strontium carbonate and natural sodium sulfate. It is also a significant producer of flourspar, barite, graphite, sulfur, feldspar, salt and gypsum. New production may be brought on stream for borates, wollastonite, garnet, calcium carbonate and others. The country covers a geographic area of approximately 2 million square kilometers (760,000 square miles), and is divided into seven geological/geomorphological provinces. Less than 20 percent has been explored in detail for either nonmetallic or metallic minerals. This leaves large areas available for the discovery of world-class industrial mineral deposits. In addition to new deposits of those minerals currently being produced, there is exploration and development potential for borates, magnesite, rare earths, nepheline syenite, heavy mineral sands and numerous others.

Jan 1, 1995

By J. A. M. Cano

A brief introduction is made on the existence of sulphides in the top gas of the Midrex Shaft Furnace, giving consideration to the operation of the furnace and the liberation of sulphur as well as its consequential effects on the reduction process. The text shows a study of sulphur distribution in the pellet, emphasizing the importance of this distribution in relation to the liberation of sulphur during the reduction. A study was made to determine the sulphur compounds that exist in the pellets, showing ways of controlling the sulphur distribution and reducing its liberation?during the reduction.

Jan 1, 1989