Search Documents

By Amir Karami, Scott Munro

This paper focuses on remediation of a 3.6 km long water conveyance tunnel that suffered two large falls of ground (FoGs), one of which subsequently progressed to the ground surface, resulting in full collapse of the tunnel. The tunnel is part of a network of water conveyance tunnels and open channels that direct water into two turbines located in an underground powerhouse, originally constructed in the 1970s. At the time of construction, the tunnel was partially supported with shotcrete or rock bolts, with no further ground support added since construction. Two sonar surveys in 019 and 01 identied two adacent large FoGs in the tunnel, approimately 1.2 km from the tunnel outlet. Historical geological and geotechnical information indicated that the FoGs occurred within a 60 m wide fault zone. Remediation plans were developed, which included stabilization of the outlet channel, the portal, the tunnel leading up to the FoG areas (1.2 km length) and the FoG areas. Several remediation options were considered to restore the tunnel, including construction of a diversion tunnel to bypass the FoGs or remediation of the FoG areas with steel ribs and backlling the void above the FoGs to surface.

Jun 23, 2024

By M. F. Goodrich

The concept of using water-only cyclones as a clean coal scalping device preceding a heavy media cyclone circuit shows considerable promise, as it can considerably reduce the feed to the heavy media cyclone circuit. The system will not perform as well as a heavy media cyclone circuit alone, but the resultant loss in yield is small and may be negligible under some conditions. The concept of water-only cyclone scalping has previously been suggested by others. By reducing the amount of raw coal to be processed in the more expensive circuits overall capital and operating costs may be reduced. There are a few commercial plants with circuits operating on this concept. In the Warwick and Rowland plants water-only cyclones are used to scalp the feed to a heavy media vessel and Deister tables respectively while Amherst Coal Company's McGregor plant uses them to scalp the feed to a heavy media cyclone circuit. The system was evaluated on a technical basis, both from a theoretical viewpoint and by analysis of a computer simulation, in order to gain a fuller understanding of its usefulness and limitations.

Jan 1, 1977

By Steven J. Schatzel, James Addis, K. Vaibhav Raj, Berk Tulu

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to enhance methane control and mine ventilation practices at coal mines, as a method to mitigate hazardous work conditions. NIOSH researchers conducted case studies to investigate the effectiveness of existing systems and improve performance to decrease the potential for unplanned or excessive methane emissions. At one mine, drainage was influenced by hydrofracking inefficiencies where two of the six wells showed good frack development. Methane content was variable, from 300 ft3/t to 600 ft3/t. This paper also summarizes overburden movement during undermining and the estimated quantities of gas transported to the mine using FLAC3D and CFD modeling. The findings from this research effort highlight considerations based on specific mine conditions that may also be applicable to most longwall mines utilizing methane control systems.

Feb 1, 2025

By L. Xia, B. Hart, V. Sidorkiewicz

Sodium silicate(s), also known as “water glass”, are one of the oldest and most widely used industrial chemicals. Its first use in North American mining operations can be traced back to around 1925, which coincided with early use of xanthates in mineral flotation. Silicate functions as a sulphide and non-sulphide gangue mineral dispersant, depressant and modifying reagent in grinding and flotation operations. It is believed that soluble sodium silicate promotes selectivity of value added sulphides against gangue minerals, resulting in both grade and recovery improvement. This paper seeks to link improved grade/recovery to the interaction characteristics of minerals and the sodium silicate. A systematic study was performed with individual mineral species, an artificially designed model ore and the feed ore from a copper metallurgical operation. The function of sodium silicate was evaluated in the context of colloidal chemistry and linked to mineral surface chemistry. Measurement of pulp rheology and mineral zeta potential identified that sodium silicate works as a dispersant. The dispersion is accomplished by increasing a mineral’s net surface charge, resulting in a mineral variable change in viscosity. Bench scale laboratory flotation tests suggest that better dispersion leads to a diminished interaction of chalcopyrite with gangue. The improved Cu grade and recovery then are likely in response to an increased accessibility to collector along with a linked increase in particle bubble attachment resulting in better separation efficiency. ToF-SIMS surface chemical analysis of the flotation samples found a higher proportion of sodium silicate on minerals from the flotation tailings relative to the concentrates. Moreover, attachment of sodium silicate appears to be mineral specific; the data indicates that sodium silicate favours the surface of gangue phases over the value sulphides. INTRODUCTION Mineral processing involves enrichment of valuable minerals from an ore, where the separation process utilizes differences between the properties of the value-added and gangue minerals. The properties of minerals, for example composition, specific gravity, particle size, magnetic properties etc., in any flotation feed ore, can vary significantly between the various minerals present. In flotation seperation surface chemistry and wettability is a significant component promoting selective separation of the various mineral phases [1,2] Mineral surface wettability can be changed, advantageously or deleteriously, by many factors including: surface layer alteration through oxidation; galvanic interactions; attachment of secondary precipitates; the adsorption of various reagents [3] In the flotation context the wettability of a minerals surface can be manipulated by various reagents. Collector reagents may selectively attach to specific minerals in the mineral/water slurry enhancing their surface hydrophobicity, increasing bubble-attachment efficiency and improve flotation kinetics and mineral recovery [4]. In contrast, depressant reagents may selectively reduce a minerals surface hydrophobicity resulting in poor particle-bubble attachment and non flotation. In essence, a mineral flotation flow sheet is designed to induce/promote a hydrophobic surface to the value mineral and a hydrophilic surface to all others. Therefore, the versatility of the froth flotation process lies in the selection of different flotation reagents.

Jan 1, 2019

By R. L. Keiski, H. Miettunen

"The serpentinite massifs of Hitura are located in the municipality of Nivala in Central Finland. The most important sulfide minerals in the ore are pentlandite, pyrrhotite and chalcopyrite. The ore body consists of amphibolite rocks in contact with serpentinite against mica gneiss. The mean Ni grade of the ore is about 0.7%, and the highest Ni grades have been encountered in close contact. In general, the inner parts of the ore are strongly serpentinized ultramafite and some sulfides have been converted to mackinawite and valleriite. The degree of alteration varies considerably within the ore body and, correspondingly, the grain size of the sulfides varies as well. In this study, flotation tests were done with samples from different zones of the ore body. The flotation test results on the bench scale and plant scale are discussed in terms of the mineralogical features of the ore. Ores in the North Hitura zone differ from those in the South Hitura zone.IntroductionThe Hitura nickel mine, like the entire Nivala area, is part of the Bothnian Svecokarelian schist zone, where numerous Ni-Cu boulders have been discovered since the early 1930s. The Nivala area has therefore been the subject of exploration activities by the Geological Survey of Finland (GSF) and mining companies. The first period of exploration started in 1936, and the Makola nickel deposit, located 3 km south of the Hitura mine, was discovered by GSF in 1937. About 415,000 tonnes of ore were mined at Makola between 1941 and 1954. In 1937, during the exploration and development stage of the Makola mine, boulder tracing and a geophysical survey revealed a significant ultramafic body with some lowgrade Ni-Cu occurrences in the South Hitura zone.In 1961, GSF continued the exploration program in the area and discovered the North Hitura ultramafic complex and its allied Ni-Cu occurrences. In 1964, Outokumpu Oy bought the property and, after underground exploration, comprehensive mineralogical studies, process research and a feasibility study, production started in 1970 (Isohanni et al., 1985)."

Jan 1, 2015

By A. M. Anthony, A. Y. Atta, S. S. Magaji, U. Abubakar-Zaria

There are two major gold recovery methods: the hydrometallurgical technique, which employs cyanide solutions, and amalgamation method, which involves mercury (Hg). These methods present considerable health, safety, and environmental concerns. Past applications of alpha-cyclodextrin (α-CD) on gold scraps show that α-CD is not only inexpensive, but is also environmentally friendly. This research work used α-CD to recover gold from gold ores instead of gold scraps. The gold ore was sourced from Shanono gold deposit site Kano State,Nigeria. The gold ore was characterized by fire assay (FA) for the precious metal. The concentrate was digested with aqua regia (AR) for 24 h. Modified AR, where hydrochloric acid was replaced with hydrobromic acid, was used for the gold digestion due to the good match in molecular recognition between gold bromide ion (AuBr)− and α- CD in a second sphere coordination complex. The digestate was characterized using atomic absorption spectroscopy (AAS). Gold recovery using this technique is pH sensitive, and five pH values (2.0, 3.6, 4.0, 5.4, and 6.0) were investigated. FA analysis showed the Shanono gold ore deposit contains an average of 4.71 ppm of gold, AAS analysis showed highest gold recovery of 69% at pH 4.0, which is lower than recoveries from the metal scraps. This could be due to the presence of other gangue minerals closely associated with the ore. However, gold recovery using α-CD on Shanono gold ore has shown to have a higher yield of 69% compared to 35.5% yield obtainable by Artisan Small Scale Miners using mercury.

May 5, 2020

By Taghi Sharizadeh, MAURICE SUNKPAL, ELAHEH TALEBI, PEDRAM ROGHANCHI

Excessive heat exposure is among the health and safety hazards that have adverse effects on the mine workers. The very nature of the underground climate makes it a convenient avenue for heat generation and accumulation from several heat sources including autocompression, equipment, and heat from strata. This study investigated the effects of clothing insulation and acclimation on the thermal comfort ofmineworkers who are exposed to heat in underground working environments. Several clothing ensembles have been considered to analyze the effect of the thermal resistance of clothing on the thermal comfort of workers. To investigate the impact of the clothing insulation, the thermal comfort limit of an underground miner was calculated in the form of maximum allowable exposure time for an 8-h shift. Parametric analyses were subsequently performed using an already developed thermal comfort model using MATLAB software. The results demonstrate that clothing insulation has a significant effect on the thermal comfort of mine workers. Increase in the clothing insulation decreases the maximum allowable exposure time of mine workers. This is especially true for the new and non-acclimated workers. Since acclimatized workers can tolerate a higher level of the dehydration and are capable of losing more water by sweat per shift, the maximum allowable exposure time for the acclimated workers are higher than non-acclimated workers. These analyses have shown that acclimated workers can have more continuous work per shift compared with non-acclimated workers. For example, in an environmental condition with clothing that a nonacclimated worker cannot work more than 5 h, an acclimated worker can work a full 8-h shift.

Jun 29, 2020

By Pratima Meshram Abhilash

In this review, availability of germanium in primary and secondary resources and its recovery from these resources are presented. With nearly 40% germanium consumed in fiber optics and scarcity of resources, the global consumption outplays the primary production. Germanium exists as a substituted element in zinc sulfide matrix of lead–zinc sulfides and lignites. Nearly 60% of the germanium supply is met by zinc refining residues, and about 20–30% of germanium is produced from coal and its by-products. Germanium recovery from various resources such as zinc plant residues, coal and coal plant waste, spent optical fibers, and copper flue dust has been examined. Bioleaching was exploited by few researchers to extract germanium from zinc sulfides, sulfide tailings, jarosite, coal fly ash, and flue dust. This review covers the various work carried out by different chemical separation processes, viz., chemical precipitation, solvent extraction (SX), ion exchange (IX), and membrane processes, as well as biological approaches.

Jan 16, 2022

By J. O. Marsden, J. H. Gourdie, J. R. Arnold, J. G. Mansanti

During the testing and design of the Gold Fields' Chimney Creek mine, it was found that a much higher carbon loading was possible with CIC (carbon-in-solution columns) than with CIP (carbon-in-pulp). In an effort to keep the carbon handling minimized, an emphasis was put on forcing gold to the CIC circuit rather than the CIP. After considerable study, it was found that a circuit with two thickeners and an interstage leach would force 90% of the gold to CIC. Computer modelling indicates that the benefits of the hybrid circuit include higher recovery, less carbon handling, fewer leach tanks, and lower reagent costs.

Jan 1, 1990

By R. Todd Swinderman

"Higher production demands across all bulk handling segments require increased efficiency at the lowest cost of operation, in the safest and most effective manner possible. As conveyor systems become wider, faster and longer, more energy output and more controlled throughput will be needed. Add an increasingly stringent regulatory environment and cost-conscious plant managers must closely review which new equipment and design options align with their long-term goals for the best return on investment (ROI).There are primarily two separate market segments using conveyor belts. One is in process industries such as food, chemicals, paper and powders. Handled in relatively low volumes, the bulk materials that enter these processes are generally of a consistent size and quality. The other market includes mining, coal handling and cement, where the bulk material’s quality and size vary, and the volumes are typically much greater. While both segments face similar issues with safety and environmental control, the properties of the materials handled and the volumes transferred suggest different approaches, with one thing in common: increased belt speeds requiring modern equipment upgrades.Safety at higher belt speedsWith companies recognizing that safety does indeed pay, safety is likely to become a new source of cost reduction. The percentage of mines and processing facilities with a robust safety culture are likely to increase over the next 30 years to the point where it is the norm, not the exception. In most cases, with only a marginal adjustment to the belt speed, operators quickly discover unanticipated problems in existing equipment and workplace safety. These problems are commonly indicated by the larger volume of spillage, increased dust emissions, belt misalignment and more frequent equipment wear or failures."

Jan 7, 2017

By Randy Reed, Barbara J. Arnold

Respirable crystalline silica poses a significant health risk, with the American Lung Association estimating that 2.3 million workers are exposed to silica in the workplace. This includes mine workers as well as those in many other industries. Reducing dust formation is sometimes not possible so other methods to reduce exposure are critical. These methods include the use of surfactants to reduce airborne dust particles. However, it is the proper selection and application of surfactants that leads to reduced dust exposure. A discussion of how surfactants work, especially for silica dust, leads to guidance for surfactant selection followed by a review of technologies for their application.

Feb 1, 2024

By Kim B. Shedd, Erin A. McCullough, Donald I. Bleiwas

"The earliest known use of cobalt was to make blue glass in Mesopotamia before 2000 B.C.E. Since then, innovations across many diverse industrial sectors transformed cobalt into an essential commodity for contemporary society. The physical and chemical properties of the element cobalt and its alloys and compounds make them indispensable for a variety of applications, including aircraft engines, hybrid electric vehicles, machine tools, missile guidance systems, petroleum refining and smartphones. As a major industrialized nation, the United States is a leading consumer of cobalt and cobalt-containing products. However, with few exceptions, U.S. cobaltcontaining ore deposits are of low cobalt grade. Historically, U.S. cobalt mine and refinery output have not met domestic cobalt demand. As a result, U.S. cobalt chemical and alloy producers need to procure most of their cobalt from the international market, which can become susceptible to supply risk.The 1978 Cobalt Crisis illustrates supply risk. At that time, the Democratic Republic of the Congo (DRC) (then known as Zaire) was the world’s leading producer of mined and refined cobalt. An insurgent invasion of the country’s copper-cobalt mining region during a period of high cobalt demand and low producer inventories caused a temporary supply shortage in the international market. The monthly average cobalt spot price increased from $18/ kg ($8/lb) before the crisis to $99/kg ($45/lb) seven months later. The high price and concern about potential disruptions in supply prompted manufacturers to reduce or substitute for cobalt where possible, and encouraged increased recovery of cobalt from scrap. The DRC has regained its position as the leading producer of mined cobalt globally and continues to be characterized by high governance risks (U.S. Central Intelligence Agency, 2015; World Bank, undated). This article will present current and historical world cobalt production trends, which can help inform discussion about the variety of international supply chain risks consequential to its trade."

Jan 12, 2017

By F. Dehghani, B. Rezaie, T. Ghosh, A. Sachan

Comminution is an integral part of the mineral extraction process. However, the influence of the comminution method (ball and rod mills) on silica and magnetite particle shapes has not been substantially investigated. Shape parameters for fractions of -250+212, -150+125, and -106+75 μm sizes were examined utilizing a scanning electron microscope and a Clemex vision PE image analysis system. The silica particles displayed higher elongation and flatness parameter values for rod mill products, but roundness and relative width parameter values of rod mill products are less than that of the ball mill products. Magnetite particle elongation and flatness parameter values of ball mill products in fraction sizes of -250+212 and -106+75 μm are larger than rod mill products, but roundness and relative width parameter values of ball mill products are smaller than rod-mill products, but for the -150+125 μm size range the result is converse. Furthermore, particle elongation and flatness increased with decreasing particle sizes of silica, whereas, roundness and relative width decreased for both Ball and Rod Mills. In case of magnetite, ball mill products displayed an increase of flatness and particle elongations with decreasing particle sizes but flatness increased and roundness and relative width decreased. Similarly for rod mills, magnetite fractions of -150+125 μm were found to have the largest values of elongation and flatness. INTRODUCTION Comminution alters the size and shape, causes lattice distortion, changes chemical composition, surface area, surface-free energy, and polymorphic transformation of all materials. The quantity and quality of such changes depend on specifications of the material feedstock, the type of mill being utilized, the specific energy input, ambient temperature, and environmental pressure [1]. The shape difference between the milled products depends on different grinding mechanisms and the respective breakage principles that these mechanisms depend on [2, 3]. With decreasing particle sizes, the nature of the particle surface become crucial [1]. The influence of the breakage technique has been found to be non-trivial and heavily dependent on the type of grinding mill used for particle size reduction [4]. Shape is an important industrial parameter for predicting particle behavior in downstream processes. The shape parameter affects the way particles burn, compact, are recovered, flow in fluids, sinter, float, agglomerate, fluidize, interact with pulmonary tissue, cut, abrade, react with chemicals, form structural materials, and retain and permit fluids to flow [5, 6]. The distribution of particle sizes and shapes are important for mining, civil and chemical, pharmaceutical, and various other industries with interest in the population modeling of atmospheric dusts, smoke, and grit [1, 3, 6]. The shape parameter not only affects the chemical, physical, surface properties of particles but is also important for downstream processes [5, 6]. Image analysis has been found to provide detailed information about size and shape of the particles and can be used for the control of product quality [4].

Jan 1, 2019

By Juan L. Yarmuch, Gonzalo Sepulveda

This article presents a novel approach to address the mining width-constrained open pit mine production scheduling problem in the context of medium-term planning. A mathematical formulation is proposed to incorporate mining width constraints into the production scheduling process, aiming to maximize the NPV of the schedule while ensuring enough room for the operation of mining equipment. To tackle the computational challenges posed by large-scale instances of the problem, we propose a method based on variable fixing and horizontal precedence generation. In this study, we apply the developed model to real-world scenarios from Radomiro Tomic short-term mine planning problems such as optimizing the timing of major truck maintenance and the impact of external factors, like the delay in the production of the Chuquicamata underground project. Remarkable improvements are observed with the mining width-constrained model. Specifically, the mining width satisfiability is enhanced from 2 to 60% compared to the traditional open pit mine production scheduling model, underscoring the significance of incorporating these constraints. The proposed method showed good results reaching optimality gaps within 5%.

Mar 28, 2024

By J. A. Mejia

The combination of high-resolution X-ray microtomography (HRXMT) image analysis and Lattice-Boltzmann Method (LBM) simulations has demonstrated the ability to describe real multiphase flow problems in fine coal filtration. The single component multiphase flow He-Chen-Zhang LBM model was used to simulate filtration with actual HRXMT images of pore network structures produced in filtration experiments. The analysis performed on coal, silica, and glass bead filter cakes showed that particle shape and wettability are two of the most important factors in the retention of moisture during filtration.

Feb 23, 2014

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL, N. Morales

The steepness of the slopes of an open pit mine has a substantial influence on the financial return of the mine. The paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice, pitwall profiles are often planar in cross-section within each rock layer; i.e., the profile inclination across each layer tends to be constant. Here instead, a new geotechnical software, OptimalSlope, is employed to determine optimal pitwall profiles of depth varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties, and factor of safety (FoS). Bench geometries (bench height, face inclination, minimum berm width) are imposed in the optimization as constraints which bind the maximum local inclination of the sought optimal profile together with any other constraints such as geological discontinuities that may influence slope failure. The obtained optimal profiles are always steeper than their planar counterparts (i.e., the planar profiles exhibiting the same FoS) up to 8° depending on rock type and severity of constraints on local inclinations. The design of a copper mine is first carried out employing planar pitwalls, secondly adopting the optimal pitwall profiles determined by OptimalSlope. The adoption of optimal slope profiles leads to a 34% higher net present value and reductions of carbon footprint and energy consumption of 0.17 Mt CO2 eq and 82.5 million MJ respectively due to a 15% reduction of rockwaste volume.

Feb 9, 2022

By Rong Lu, Hao Wu, Bing Dai, Guoyan Zhao, Li Cheng, Weizhang Liang

Affected by the disturbance of blasting activities, deformation instability and rock dynamic disasters are prone to occur in deep hard rock roadways. Thus, it is particularly necessary to understand the failure behavior of rocks and roadways under dynamic loads. In this study, a series of impact loading tests were carried out on sandstone samples with and without a circular cavity by a modified split Hopkinson pressure bar (SHPB) test system. The mechanical properties and energy evolution of the samples were systematically investigated, and the effect of cavity size was analyzed. The results showed that the presence of the cavity in the samples weakens the dynamic compressive strength by more than 10%, and the peak strain and brittleness are also reduced to varying degrees. Under dynamic loading, spalling cracks occur first on the roof and floor of the cavity, and then different numbers of shear cracks are formed on the sample diagonals. The eventual shear failure mode is the result of the connection of the shear cracks and the cavity. As the cavity radius increases, the dissipated energy density and fractal dimension both grow accordingly, leading to smaller and smaller rock fragments. The dynamic failure behavior of the circular cavity can be well explained based on the dynamic stress distribution law. Overall, this study can provide a reference for the study of the mechanism of rock burst in deep roadways.

Feb 18, 2021

By Jian Wang, Kun Li, Hao Wu, Juan Nan

In this paper, in order to solve the problems of low accuracy and slow speed of fire flame recognition, an extreme learning machine (ELM) method based on improved Harris hawks optimization (IHHO) is proposed for fire flame recognition. A novel Harris hawks optimization (HHO) is used to solve the problem of parameter selection of ELM. In order to solve the problem that the original HHO is prone to fall into local optimum, firstly circle mapping is used to initialize the population to solve the problem of uneven distribution and small range of the initial population. Then the formula of escaping energy of HHO is modified to make the population have a large range in the middle and late iterations while gradually decreasing in the whole iteration process. Thus, the exploitation stage in HHO is improved to make the search range smaller near the optimal solution to accelerate the convergence process. Finally, at the end of each iteration, a certain number of individuals are selected to perform Gaussian and Cauchy hybrid mutation to prevent the IHHO from falling into local optimization. Through three groups of experiments, the effectiveness of the proposed IHHO and IHHO-ELM is verified. In experiment 1, the convergence performance of IHHO is significantly better than that of the other remaining algorithms in the test results of six benchmark functions. In experiments 2 and 3 of real fire flame recognition case, IHHO-ELM outperforms other remaining algorithms on the whole and has significant advantages in some indexes.

Jan 17, 2023

By J. H. van Laar, C. S. L. Schutte, M. Le Roux

Highly energy-intensive systems prone to wastage are significant causes of unnecessary energy losses in industry. Deep-level mine chilled water reticulation systems fall within this category of inefficient energy-intensive systems. Some techniques (measured baselining, zero-waste baselining, leak detection, and control valves) exist to identify and reduce wastage in mine water reticulation systems. However, these techniques have not been compared, which begs the question of which is more accurate. A need, therefore, exists to compare these methods to determine the effectiveness of each. This study investigates each method and applies them to a case study mine, providing a platform for comparison. These methods identified wastage ranging between 2 and 20 l/s (3–30% of water consumption). The comparative effectiveness of the methods from best to worst was found to be zero-waste baselining, leak detection, control valves, then measure baselining. This study proposes an application procedure combining the considered methods to identify and eliminate wastage on deep-level mine systems more efficiently.

Jan 31, 2024

By R. Bissonette, C. Sunderman, R. Jacksha

The ability of wireless systems—e.g., voice communication, proximity detection, tele-remote operation, telemetry, etc.—to function satisfactorily (coexist) in the presence of other wireless systems is critical to the safety and health of mine workers. The failure of wireless systems to coexist could result in the delay, corruption, or outright loss, of critical data, voice, or video information. However, no mining-sector-specific regulations, standards, or guidelines exist to ensure the safe coexistence of wireless systems. This paper introduces the concept of wireless coexistence, implications in the mining industry, and the National Institute for Occupational Safety and Health’s (NIOSH’s) research approach to develop guidelines and recommendations to ensure safe wireless coexistence.

Feb 1, 2023