Search Documents

By K. Thambi

The court in Baleni v Minister of Mineral Resources [2019] 2 SA 453 GP and [2020] 4 All SA 374 (GP), deliberated on the protection of rights of a community holding informal land tenure under Customary Law. The contention related to the necessary level of consent needed to acquire a mining right over such land. Moreover, whether consultations with such communities (Section 23, Mineral and Petroleum Resources Development Act 28 of 2002 (MPRDA) or consent (Section 2, Interim Protection of Informal Land Rights Act, No. 31 of 1996 (IPILRA)) was required to acquire such right. The case has a significant bearing on the granting of mining rights in South Africa, and the discretion of the Minister of Mineral Resources (the Minister) in this regard. However, the objectives of the MPRDA and IPILRA do not dovetail, therefore consultation and consent are not mutually exclusive (Tlale, 2020). This note argues that, despite the resounding victory of this case, the peripheral basis surrounding the decision and the various levels of engagement require serious deliberation. Equally, the degree of reliance on the IPILRA requires clarity to avoid aborting the fundamental objectives of the MPRDA. This paper provides considerations and recommendations that may reduce or eliminate the tensions between the statutory and socio-economic rights in the application of the two statutes.

Sep 1, 2022

By B. A. Obadele, R. Machaka, M. L. Raganya, M. E. Makhatha, N. A. Moshokoa

The influence of solution treatment on the phase evolution and tensile properties of Ti-Mo alloys was investigated to assess their potential use in biomedical applications. Phase formation and microstructural evolution were studied using X-ray diffraction (XRD), optical microscopy (OM), scanning electron microscopy (SEM), and electron backscatter diffraction (EBSD). The mechanical properties were characterized by means of tensile tests and bending strength. XRD analysis showed that solution treatment increased the volume fraction of β phase and supressed the α" phase. The microstructures of the as-cast alloys consisted of β equiaxed grains with sub-grain structures of different sizes, while the solution treated alloys comprised β equiaxed grains only except for Ti- 10.02Mo, which comprised needle-like α" structures. EBSD showed an increase in the volume fraction of the ω and α" phases in all the alloys after solution treatment. The elastic modulus and UTS of all the alloy significantly decreased after solution treatment, except for Ti-15.05Mo,whereas the elongation significantly increased. The fracture surfaces of all the alloys after solution treatment indicated more ductile behaviour than brittle

Jun 10, 2024

By B. Genc

Improving student success rates without compromising the quality of graduates is one of the biggest challenges expanding university programmes are facing in South Africa. By establishing a new Mine Design Laboratory (MDL) for higher learning in Mining Engineering, the School of Mining Engineering at the University of the Witwatersrand (Wits Mining) has achieved one of the important goals in its five-year strategic plan, i.e. to improve throughput in all years of study. Although the establishment of the laboratory has been a costly exercise, results so far have shown an improved success rate in most subjects taught in the facility. This paper outlines the design and equipment of the laboratory, the facilities incorporated, a comparison with the old laboratory, and the performance of students?all of which indicate how important it is to have proper facilities to improve the teaching of, and learning by, large classes. Through this initiative, Wits Mining has taken an important step that will contribute to addressing the skills shortages in the mining industry.

Jan 1, 2012

By S. J. Thomas, P. A. Lilly

With support from the Australian mining industry and the Federal Government, three Australian universities are collaboratively developing flexible-format, web-based course content and delivery in rock mechanics for undergraduate mining engineering students. This paper describes the educational philosophy behind the development and summarises other salient features of the Program. Mit der Unterstuetzung von der austlalischer Bergbauindustrie und der Bundesregierung, drei austlalische Universtaeten in Zusammenarbeit entwickeln flexibel Netzgengruendet auf Lehrganginhalt und Lieferung in Felsgestein fuer Bergbaustudenten. Dieses Schreiben erlautert das Unterrichtsphilosophie hinter der Entwicklung und Zusammenfassung anderer Hauptpunkte von diesem Programm" Avec l'assistance de l'industrie miniere australienne et du gouvernement federal , 3 universites Australiennes collaborent a la mise en place d'un programme de mecanique des sols pour etudiants- ingenieurs en mines. Ce programme serait a la fois flexible et accessible par Internet. Ce document decrit la philosophie pedagogique de ce projet et en souligne les characteres importants.

Jan 1, 2003

By F. Magweregwede, S. Khan

Circular economy opportunities for the mining sector are presented in this paper. A literature review was undertaken, followed by qualitative data gathering through survey questionnaires and unstructured interviews, and stakeholder engagements through workshops. The circular economy opportunities were identified and categorised according to the three circular economy principles of designing out waste and pollution, keeping products and materials in use, and regenerating natural systems. Opportunities aligned with the first principle include increased ore extraction efficiency processes, water recovery and recycling, substitution of raw materials, technology and waste utilisation for carbon capture and biotechnology. The second principle includes opportunities such as zero waste-to-landfill strategies, repurposing of mine waste, re-mining of tailings, recycling metals and processing of residues, and urban mining of electronic waste. Opportunities aligned with the third principle include the adoption of renewable energy, green hydrogen production, repurposing of post mining landscapes, and eradication of alien invasive vegetation. Furthermore, the challenges of implementing circular economy in the mining sector are discussed. The current rate of waste generation from mining activities far exceeds the rate of reuse and repurposing. Recycling of large tyres and characterisation of hazardous electronic waste also pose challenges. The most implementable circular economy opportunities in the mining sector are those aligned with the second principle of keeping materials in use. The high impact opportunities aligned with the first principle of designing out waste and pollution, and the third principle of regenerating natural systems, are more difficult to implement as they require large investments.

Dec 15, 2025

By F. Dutoy, M. B. Stella, C. F. Carrozza

Rare earth elements (REEs) are indispensable components in the manufacturing of high-tech devices, renewable energy technologies, and defence applications. As global demand for these elements continues to rise, there is a pressing need to optimize extraction processes for both efficiency and environmental sustainability. This study explores approaches to rare earth extraction using Ionquest® 801 and integrates a predictive modelling to enhance process understanding and optimization. We conducted a screening test varying pH process to evaluate the best extraction efficiency. Starting pregnant leach solution (PLS), solution was prepared in the lab with the following rare earth elements: La, Ce, Gd, Dy, and Υ, at 0.02 M for each element. The data obtained were used to develop empirical and mechanistic models to predict rare earth extraction yields and flowsheet. Further tests were performed by mixing specific concentrations of different extractant and/or phase modifier. Our experimental results demonstrated the effectiveness of the proposedextraction methods, highlighting improvements in both yield and selectivity. The developedmodels successfully captured the complex relationships between process parameters and extraction efficiency, providing valuable insights for process optimization.

Nov 6, 2024

By Gernot Beer, Christian Dünser, Marcos Noronha

The main findings of the joint research initiative “Numerical Simulation in Tunnelling” and a follow-on project on efficient numerical simulation models for tunnelling are presented. Die wichtigsten Resultate des Forschungsschwerpunkts „Numerische Simulation im Tunnelbau“ und einem Folgeprojekt über effiziente numerische Simulationsmethoden werden präsentiert Les résultats les plus importants du point principal de la recherche "simulation numérique dans la construction de tunnels" et un projet consécutif sur des méthodes de simulation numériques efficaces sont présentés

Jan 1, 2003

By S. Dey, C. Bhar, S. K. Mandal

Loading and hauling of ore and waste are the key operations of an opencast coal mine and entail a high operational cost. The productivity of a mine can be increased by reducing the cycle time of loading equipment as well as utilizing dumpers optimally. In this paper we discuss the impact of rock type, bucket fill factor, rock fragmentation, the height of the cut, and angle of swing of the bucket on shovel performance. A time study is conducted on shovels in an opencast coal mine with experimental blasts of rocks to assess the impact of different factors on the performance of the shovel. Based on the data, the authors applied multiple regression (MR) and artificial neural network (ANN) techniques to develop different models for the prediction of the shovel cycle time. Developed models are validated by comparing the predicted data with actual field data. With the help of the best model, the plausible fleet size is determined in order to utilize the shovel and dumper optimally and to improve the performance of shovel–dumper operation.

Oct 1, 2022

By T. Bui, T. Wallmach, S. B. Blancher, A. Back, M. Pierre, V. Delarue, A. Kanzari

This study investigates nickel laterite porosity and its impact on geometallurgical modelling. We performed a detailed mineralogical study on a set of Ni-laterite samples originating from New Caledonia. Samples were analysed after heavy liquid separation by automated SEM (QEMSCAN®). Laboratory and QEMSCAN® modelling results do not correlate well. Ideal physical mineral properties such as mineral densities used in QEMSCAN® modelling do not match the actual physical densities of minerals. The presence of empty or water-filled pores can represent important amounts in minerals and change the overall density of a particle. An adequate modelling of real density separation of minerals and particles should consider the water-filled pores. The first step towards a better simulation was to integrate pores larger than 10 μm in diameter filled with water (density of 1 g/cm3) in the QEMSCAN® database. The results approached, but did not match the physical laboratory results. The second step was to identify nanometer to micrometer sized pores, which could not be identified by QEMSCAN®. It was possible to identify nanometric pores in enstatite, Fe-oxides, serpentine, talc and quartz, and radial aggregates of fibrous Fe-oxyhydroxides with high resolution SEM (HR-SEM). The quantification of those micro-sized pores was performed on 2D HR-SEM images using image-processing techniques developed in Python to calculate the nanometer to micrometer scale pores in each mineral. Despite the limitation of converting 2D imaging into 3D objects, in our case pore sizes and porosities, we were able to calculate a mean value of porosity for each mineral. The integration of this porosity in the calculation of particle densities yielded a good match between the QEMSCAN® model and the laboratory experiment results. Despite the complexity of a strongly weathered material, such as Ni-laterites, a good knowledge of the ore makes it possible to build reliable processing models. Keywords: Mineralogy, geometallurgy, nickel laterites, SEM, QEMSCAN®, porosity, density

Jan 1, 2020

By V. I. Ryaboy, V. P. Kretov, I. V. Ryaboy

Attachment of collectors containing thioamide groups to sulfide minerals is interpreted as interaction between NH-acids and sulfides acting as solid bases with the formation of a donor–acceptor reagent–mineral bond. As the acid function of the reagents increases, their sorption optimum is observed to shift to a less alkaline region. The developed concept has enabled us to propose a method for calculating optimal pH values for the sorption of reagents on mineral surfaces depending on the acidity of the reagents and the pH value of the medium. Our estimates correlate well with the experimental data. We studied the spectra of the reagents containing thioamide groups and the spectra of copper salts and their surface compounds on an oxidised copper film, chalcopyrite, and pyrite using the infrared (IR) spectroscopy. Some effective applications are described of reagents containing thioamide groups in the flotation of copper, copper-molybdenum, and gold ores, both separately and in combination with other collectors. It is shown that the flotation performance is maximised by adding two- and three-component collector combinations, including collectors containing thioamide groups. In this case, the increase in the recovery of copper, molybdenum, and gold is up to 2-5% compared to conventional process conditions. A new, high-performing reagent containing a thioamide group is proposed. A commercial pilot batch of the reagent was produced and sent for flotation tests in gold ore applications. Keywords: Thioamide reagents, dialkyldithiophosphate, collectors, flotation, arsenopyrite, chalcopyrite

Jan 1, 2020

By P. Syrjänen, Lovén. P.

Because geostatistics together with block modeling has not been studied in detail before in the rock mechanics, a two-year research program to investigate the practical use of geotechnical modeling was started in Finland in 1999. According to research work results block modeling gives good estimate of overall rock mass quality but it can not identify individual structures like faults and narrow weakness zones. Weakness zones and faults should be mapped from drill cores, surface mapping, geophysical methods etc. and manually generate 3-D structural model. Rock mechanical 3-D modeling can be used for preliminary stope dimensioning and preliminary reinforcement design. Detailed design needs rock quality mapping from drifts during excavation work. La géostatistique associée à la modélisation par blocs n'ayant pas été étudiée en détail jusqu'à présent dans la mécanique des roches, un programme de recherche sur deux ans visant à examiner l'utilisation pratique de la modélisation géotechnique a été lancé en Finlande en 1999. D'après les résultats des travaux de recherche, la modélisation par blocs donne une bonne estimation de la qualité générale de la masse rocheuse mais elle ne permet pas d'identifier les structures individuelles comme les failles et les zones géologiquement dégradées étroites. Ces zones et failles devraient être cartographiées à partir de carottes de sondages, d'une cartographie de surface, de méthodes géophysiques, etc. et générer manuellement un modèle de structure 3D. La modélisation mécanique des roches en 3D peut être utilisée pour un dimensionnement de la chambre et un plan d'armature préliminaires. Un plan détaillé nécessite l'élaboration d'une cartographie de la qualité des roches des galeries lors des travaux d'excavation. Da man früher Geostatik und Block-Modellieren in der Gebirgsmechanik nicht detailliert untersuchte, wurde 1999 in Finnland ein zweijähriges Untersuchungsprogramm in Angriff genommen. Aufgrund der Untersuchungsergebnisse ergibt das Block-Modellieren eine gute Beurteilung der gesamten Gebirgsmassenqualität, kann jedoch einzelne Strukturen wie Verwerfungen und kleine Schwachzonen nicht identifizieren. Schwachzonen und Verwerfungen müssen demnach aus Bohrkernen, oder mit Hilfe von Oberflächenkartierung, geophysischen Verfahren usw. ermittelt und danach ein 3-D-Strukturmodell manuell erstellt werden. Felsmechanisches 3-D-Modellieren ist für die vorbereitende Abbaudimensionierung und für die vorbereitende Bewehrungsplanung verwendbar. Ein detaillierter Entwurf benötigt die Kartierung der Gesteinsqualität aus den Gesteinsstrecken während der Ausbrucharbeiten.

Jan 1, 2003

By P. Lenegan, R. Masethe, R. I. L. Ferreira

Underground mining in high rock-stress environments can induce unanticipated dynamic rockmass deformation, posing a serious risk to the workforce. Data collected by seismic networks are imperative for the design-as-you-mine process. Often an inappropriate assessment of the seismic hazard is done when unnecessary data are included in analytical techniques, particularly short-term time frames. Depending on the methodology or application of data analysis and interpretation, some of the information may not be relevant and even detract from the objective. By using the spatial event clusters associated with active workplaces to define the shape and size of the polygons for data selection for subsequent analysis, a problematic subjective component can be eliminated. The mining of tabular reefs in South Africa, be they gold- or platinum group metals, is very extensive, and underground workplaces are often widespread. Production stoppages are very costly, especially for marginal mines, so there is just cause not to evacuate an entire operation’s workforce following the occurrence of a large mining-induced seismic event. A rationale based on the damaging peak particle velocities (PPV) of the past seismicity can exclude the unaffected underground personnel and allow a quick orderly withdrawal where required. Micro-deformation may precede rockbursting, which can occur on-shift close to the workface. A mine-wide array of geophones suitable for the accurate location and analysis of seismicity may not be able to detect these higher-frequency emissions. Inexpensive but fit-for-purpose accelerometers, providing real-time, continuous measurement of acoustic rockmass deformation near the workplace, integrated through underground and surface communications networks, are shown to record ‘rock-talk’, clearly distinguishable from the instrument background noise, which can be in the order of hours leading up to an imminent damaging seismic event.

Jan 12, 2025

By G. Chisakuta, P. Bwando, G. Mitshabu

By the end of 2022, the south-eastern Copper Belt region of the Democratic Republic of Congo was host to more than 40 small, medium, and relatively large sized copper solvent extraction sites. To date, solvent extraction reagents supplied in this region have never exceeded 50% of ketoxime content. We generated laboratory extraction and strip isotherms and used these with the BASF IsocalcTM modelling software to assess the benefit of using higher ketoxime blends on the main metallurgical performance indicators such as copper recovery and net transfer. Pure ketoxime extractants combine a relatively low strip point and a decent loading capacity, which are most effective as the pH of the pregnant leach solution gets closer to 2.

Jan 1, 2023

By C. J. Badenhorst

The primary focus of management today is safety, or preventing negative, generally irreversible, events of acute duration. The outcomes of safety-related events are usually visible and can evoke strong emotions if the results are severe. Experts now see that occupational illness and disease also result in significant emotional and financial toll to workers, their families and communities, and to their employers. Effective health and safety management must include acknowledging the importance of occupational health hazards and the proportionate application of resources to address those issues. Improvement in workplace conditions and decrease or elimination of illness and disability are due to actions within the workplace and result from the implementation of risk prevention and control measures. However, success may only be visible months or years later and may require interventions that have to be maintained over prolonged periods. This demands continuous, co-ordinated effort to ensure sustainability of diverse occupational health programmes and the relevant management systems. Too often occupational health is not seen as being part of the general management of business, but rather the function of a medical practitioner somewhere off site in a clinic. Integration of occupational health management systems with other management systems within an organization is essential for its success.

Jan 1, 2004

By F. Roelofse, D. Grobler, and M. Purchase, C. Gauert, E. Kotze

Scandium is an important industrial metal for which demand is projected to increase in the future. Although many Sc deposits are secondary, Sc is scavenged by clinopyroxene during fractional crystallization of primary, mafic-ultramafic magmas. Sc may thus occur in sub-economic concentrations in mafic-ultramafic intrusions. In this work, we present new data on the concentration of Sc in the Bushveld Complex (BC) of South Africa. The eastern and western limbs of the BC are considered to be largely pristine, primary magmatic deposits, whereas the northern limb shows evidence of largescale, localized crustal contamination. Samples from the primary magmatic cumulates of the eastern limb, from the mineralized Flatreef of the northern limb, and from the crustal-contaminated Footwall Assimilation Zone (FAZ) of the Flatreef were analysed for Sc. Despite the FAZ containing abundant clinopyroxene, interpreted to have recrystallized from the original cumulates in the presence of melted sedimentary rocks, no significant differences are seen in the concentration of Sc compared to other cumulate rocks of the BC containing less-abundant clinopyroxene. The concentration of Sc in the analysed samples is mainly controlled by mineralogy, with anorthosites, chromitites, and harzburgites containing under 20 ppm, and norites and pyroxenites containing 20–40 ppm. The parapyroxenites of the FAZ are less enriched in Sc than expected, suggesting that Sc may have been lost during alteration and recrystallization.

Sep 1, 2022

By V. van der Merwe, C. W. Siyasiya

"A petrochemical company experiences premature thermal fatigue failure of the casting moulds used in catalyst production. The aim of the project was to find an alternative alloy that would outperform the current low-alloy cast steel used for the moulds. Based on their thermo-fatigue properties, 3CR12 ferritic stainless steel and H11 tool steel were chosen for testing and comparison with the currently used BS3100 B7 cast steel. Samples of each material were subjected to temperature cycling in a Gleeble 1500TM thermo-mechanical processing simulator, followed by surface analyses. The main parameters derived from the test work were the total true strain, the hot strength of the materials, and the number of cycles to failure. Additionally, the coefficient of thermal expansion for each material was measured using a Bähr dilatometer. H11 tool steel yielded the best performance by way of having the fewest surface cracks, the lowest total true strain per cycle, the most cycles to failure, the highest hot strength, and the lowest coefficient of thermal expansion.IntroductionThe Catalyst Manufacturing Plant (CMP) is a dusty environment with temperatures higher than ambient. Molten mill scale (magnetite, Fe3O4) is tapped from the electric arc furnace into the casting moulds at temperatures close to 1600°C. After 10 seconds the magnetite is quenched with a water spray for 50 seconds to a minimum temperature of 400°C. Sometimes there is residual water in the pans from the cooling fog process (water sprays) in the empty mould. In a typical plant, the factory produces 40–44 batches a day containing between 150–300 moulds, depending on the time required for the specific batch (Buchholz, 2014). The typical batch in the CMP usually weighs about 6 t. The thickness of the tap, speed of the casting belt, and tilting angle all affect the number of moulds per batch.One of the main problems faced during the molten mill scale casting is the premature failure of the casting moulds. Cracks initiate on the surface of the mould, which is in contact with the hot catalyst, and propagate into the interior of the mould. Cracks are generally concentrated in the middle area of the mould where the catalyst makes first contact with the mould, and which experiences the highest temperature fluctuations. This suggests that the cracks are caused by thermal fatigue during the casting process."

Jan 1, 2016

By F. Dong, F. Yang, J. Wang, Z. Wang, D. Mingxia

Antimony oxide ores are important antimony resources, but their recovery is still a problem. In this paper, the adsorption behaviour and mechanism of dodecamine and quaternary ammonium salt on the surface of cervantite and quartz were investigated. The flotation behaviour of cervantite and quartz using quaternary ammonium salts and dodecylamine as collectors was studied by single mineral flotation experiments. The adsorbed amount was measured and infrared spectroscopy was used to study the ability of several cationic collectors to float cervantite and quartz. The results show that quaternary ammonium salts can simultaneously float the cervantite and quartz. It is difficult to achieve separation of the two minerals using quaternary ammonium salts as collectors. At pH>10, dodecylamine can float quartz but not cervantite, which can achieve reverse flotation separation of the two minerals. The difference between the abilities of quaternary ammonium salts and dodecylamine to float cervantite and quartz lies in the different ionisation properties of the two reagents. Quaternary ammonium salt is a strong electrolyte that is completely ionised in the pulp and exists mainly in the form of quaternary ammonium ions. Dodecylamine is a weak electrolyte and predominantly forms molecules under alkaline conditions. Keywords: Cervantite, quartz, dodecylamine, quaternary ammonium salts, flotation

Jan 1, 2020

By S. M. H. Haddad, M. Saghaeian, R. Hejazi, V. Sheikhzadeha, A. H. Baladastian, A. Dehghani Ahmadabadi

Sulfide impurities in iron ore concentrates play an important role in designing pelletising and steel making plants. Therefore attempts are made to keep the sulfur content of the final concentrate produced by the plants as low as possible. Generally, in the beneficiation process of iron ore concentrate, the removal of sulfur is performed through magnetic separation systems, followed by reverse flotation. The sulfide content of the iron ore concentrates originated from two main sources, including pyrite and pyrrhotite. In this research, in order to compare the floating capability of these two types of sulfide minerals, two iron ore concentrates with different sulfide constituents, pyrite or pyrrhotite, were selected. Reverse flotation tests were done separately on these samples under similar conditions. Process parameters considered for the tests included pH (2, 4, 6, 8 and 10), collector consumption (150, 200, 250, 300 and 350 g/t) and frother consumption (40, 50, 60, 70 and 80 g/t). Potassium Amyl Xanthate (PAX) and Methyl Isobutyl Carbinol (MIBC) were the collector and frother used in the tests, respectively. For modelling and optimising process parameters, the Central Composite Design (CCD) method was applied to the test results. Empirical coded equations were obtained for responses involving weight recovery, Fe recovery, Fe grade and S grade. Finally, comparison of test results revealed that the elimination recovery of pyrite sulfides was far greater than pyrrhotite sulfides, and it was possible to remove 84% sulfur content of the pyrite sample compared to minus 30% for the pyrrhotite sample. Keywords: Reverse flotation, pyrite and pyrrhotite, sulfur removal, iron ore concentrate, beneficiation plant

Jan 1, 2020

By J. R. Bredell, J. Branehog, C. Coetzee, J. J. van Tonder

A nutating grinding mill, exemplified by the commercial HICOM mill, achieves efficient particle size reduction through the accelerated motion of the material charge within the nutating chamber. This design, characterised by high particle velocities and rapid charge circulation, offers a compact solution compared to tumbling mills. There have been concerns regarding the mechanical reliability of kinetic joints for certain specialised mining applications. Recognising the need to model internal forces in such systems, this study focuses on the uncoupled simulation using multibody dynamics and the discrete element method. The investigation employed a small-scale experimental test mill, referred to as the NuMILL, featuring a cylindrical chamber (140 mm internal diameter, 245 mm height, 6° nutation angle). Instrumented with an array of sensors, the NuMILL provided internal load data for validating the simulations. Experiments were conducted with an empty chamber or filled with charge material. Charge materials included coarse sand or steel pellets with a charge-to-chamber mass ratio of 0.25. The mill speed ranged between 100 to 700 RPM. Multibody dynamics modelled resultant inertial and frictional loads within 5%, while the discrete element method simulated the internal material contact loads with accuracies ranging from 1% to 19%. The combined simulation approach predicted the resultant forces in the critical kinetic joint within a 20% margin. Representing the charge using rigid lumped mass elements was also studied. The presented simulation techniques, validated against experimental data, offer a robust foundation for analysing larger systems, including the industrial-scale HICOM.

Mar 5, 2025

By A. Mainza, A. Mabentsela

A finite element model of a 5 m radius DC arc ilmenite furnace in idling mode was used to test the notion that the slag solidifies when it comes in to contact with colder pig iron, thus constituting the initial step in the formation of solid slag at the slag-pig iron interface. It was found that a slag that is 150°C hotter than the pig iron does not solidify at the interface. The 150°C temperature difference between the slag and pig iron is a result of solid slag at the slag-pig iron interface, not the other way around as suggested in the literature. Calculations show that the thickness of the frozen slag at the slag-pig iron interface is 1.7 cm for the furnace used. It is proposed that slag solidification begins with the slow co-current flow of molten slag and pig iron in the outer parts of the furnace. This provides enough time for molten slag to interact with molten pig iron without solidifying. As the reduction products form due to reduction of the slag by carbon in the pig iron, the slag solidifies. This approach negates the need for the slag to solidify by merely coming into contact with an inherently colder pig iron. Making use of a low thermal contact conductance between the slag and pig iron was found to be sufficient to numerically capture the presence of solid slag at the slag-pig iron interface and to preserve the 150C difference between the slag and pig iron phase.

Mar 30, 2023