Search Documents

By Y. Tang

The paper studied the extraction characteristics of the fly ash from a location in Guizhou province. Under ordinary pressure, the fly ash is extracted by an acid and alkali, and then studied for its reaction characteristics with different extraction agentia, temperature, consistence and time. The results of acid extraction show that there are good reaction characteristics for Fe2O3 with HCl and the extraction rate decreases with the increasing of extraction time. There are good selective characteristics between Al2O3 and H2SO4 and they weaken with the increasing of temperature and the expanding of time. The best extraction results are shown with CaO and MgO because of their chemical characteristics and the over-saturation degree of the extraction processing. In addition, It?s found that it cannot leach all the substances from fly ash even with the higher consistence (10mol/L) of extraction agent, the longer extraction time (2h) and the higher temperature (100?) .It shows that the extraction rate of Fe2O3 is 82.81% and that of Al2O3 is 29.01%. The results of alkali extraction show that the extraction rate increases with the consistence of extraction agent and temperature, and the extraction rate of SiO2 by NaOH increases rapidly with the time expanding while that of Al2O3 falls gradually.

Jan 1, 2014

By Liu Xinghua

Yuanjiacun iron ore located in Shanxi province of China has finely disseminated grain size and contains refractory iron-bearing silicate gangue minerals such as chlorite. Therefore, a large amount of secondary slime (the content of -10µm fraction was up to 32.92%) was produced inevitably in fine grinding process, and chlorite was also enriched in concentrate from the content of 4.3% to 14.8% after high intensity magnetic separation. These two characteristics result in the difficulty to deal with Yuanjiacun iron ore by flotation. In this test work, contrast tests between single reverse flotation and selective flocculation desliming-reverse flotation were conducted on Yuanjiacun iron ore. The test results show that after selective flocculation desliming, the iron grade of cationic reverse flotation concentrate increases by 6.15% and the recovery increases by 7.25%; the iron grade of anionic reverse flotation concentrate also increases by 2.15%. Furthermore, analyses of grain size composition and mineral composition were carried out on separation products, the results indicate that selective flocculation desliming plays a dual role of optimizing grain size composition of flotation feed and removing iron-bearing silicate gangue minerals (chlorite) effectively.

Sep 1, 2012

By G. Aguilera

It is known that an addition of rigid particles into a fluid medium changes the flow field. Therefore, the rheological behavior of suspensions will be hardly Newtonian, such as their continuum phase. This phenomena was studied by Einstein in 1906 (Einstein, 1956) for the single case of spherical particles in a continuum liquid of a very dilute suspension. The final analysis applied for suspensions was derived from the evaluation of the behavior of ideal gases, finding a simple expression for the viscosity of the dispersion. All the following works about the hydrodynamics of suspensions at low and high solid contents was based in the Einstein´s model. For clay minerals suspensions where the physical and chemical properties of the particles are complex, it was found that the Einstein´s model is not a good approximation, even so for the most dilute dispersions. The present paper shows a new approximation that describes the non-Newtonian behavior of the suspensions of clays, and the attempt of understand how the different fine sizes, shapes and physico-chemical properties of clay particle surfaces give specific characteristics of plasticity, viscosity or visco elasticity to suspensions. Keywords: viscosity, clay minerals, einstein´s model, dilute suspensions

Sep 1, 2012

By M. Unesi, S. Haj Mohammadi, M. R. Abdoli, M. R. Garmsiri

"Hydrocyclone-thickener circuit is a promising solution to enhance the dewatering efficiency in mineral industries. The challenges in the circuit is reducing particle size in the thickener feed and the good feature is a rise in the retention time of sediments in the thickener. In this work, the effect of particle size, bed depth and residence time on the thickener performance were investigated. In this order, pilot scale columns were employed at Sarcheshmeh and Shahrebabak copper complexes. Furthermore, the influence of residence time was differentiated due to the variations in the bed depth and settling flux. Moreover, a new approach was introduced to estimate solids residence time in the thickener. results indicated that with smaller particles that are introduced to the column, the bed density as well as thickener discharge solids concentration dropped significantly. It was found that thickener discharge solids concentration fell from 59.6 to 33.8 % with reducing particle size from 130 to 22 µm in the settling flux of 20 t/m2/day. Additionally, it was found that longer residence time and deeper bed resulted in an increase in the thickener performance while the bed depth has a stronger effect. It was proved that employing a hydrocyclone prior to the thickener resuted in an increase in the dewatering efficiency.INTRODUCTION Thickeners are widely employed in mineral industries to recycle tailings and concentrate water content. A limited fraction of suspension water content is recycled using a thickener. For instance, about 50 percent of tailings water content could be recycled using a shallow bed thickener during copper processing. Since the scarcity of global water resources became more serious, the demand for improving dewatering efficiency in mineral industries became more significant [1]. A number of solutions were recommended to enhance dewatering efficiency of thickeners including optimization of current thickeners, employing deep bed thickeners and utilizing thickener-filter or hydrocyclone-thickener circuits. Optimization of existing thickeners is essential, however, it does not meet the significant demand for recycled water. The application of deep bed thickeners (known as paste thickeners) has been rising in the mineral industries [2] due to a higher dewatering efficiency while its costs is remarkable."

Jan 1, 2018

By Tamal K. Ghosh

In this study, the QEMSCAN technology is used to acquire quantitative modal, textural, mineral association and liberation data on different products generated from with or without washing, fractionation by size and density using screens and heavy liquids/panning, which has provided significant information on the quality and beneficiability of four categories of low Grade iron ores from Jharkhand-Orissa region. The deposit of low Grade iron ore has been categorized into four categories viz. Grade-I with <45% Fe(t) a) containing shale rich type and b) BHJ rich type; Grade-II with 45-55% Fe(t) and Grade-III with >55% Fe(t) containing conventional flaky, hard, kanga, lateritic, shale and BHJ litho/ore types in varied proportions. Mineralogy is similar across all samples being hematite, martite, goethite, kaolinite and gibbsite. Banded Hematite Jasper has difficult liberation characteristics due to highly compact banded mode of silica mineral occurrence with hematite. In all categories, the grade dilution is by the presence of 1) ?Discrete gangue rich litho types? at lump size and 2) ?Within ore types?. The second type of grade dilution contains coating of gangue phases around the iron ore minerals and different degree of locking of gangue phases within iron ore minerals. Further characterization and beneficiation assessment details are discussed in this paper.

Sep 1, 2012

By A. Kamali Moaveni, A. Boehm

"The current research study addresses a physical separation process of basic oxygen furnace slag “BOF-Slag” (also called Linz-Donawitz “LD” slag) for the removal of phosphorous. In order to recycle the LD-Slag into the steelmaking process, the physical dephosphorization methods are considered. The systematic geometallurgical investigation carried out on particle classes of decreasing size, which were further subdivided into susceptibility classes, shows intimate intergrowth beyond 40 µm due to slag´s fast cooling rate. Generally, LD-slag is constituted of oxide and silicate phases, among which di-calcium silicate “C2S” dominates. About 0.5 mass% of phosphorous was detected in the LD- slag, which is exclusively situated in the lattice of the C2S. The comparatively high grinding resistance (Rittinger index 12.9 cm²/J) of the LD-slag reflects the energy demand to liberate the phosphorous carrying phase from the iron containing minerals, while separation efficiency decreases in the very fine particle size range. Hence, the conversion of the phase intergrowth pattern was considered alternatively to re-build the mineral phase structure of the material to a separable interlock pattern. Carbon dioxide, as the most convenient substance in the steelmaking plants, was applied to digest the C2S in the presence of water and to reduce the basicity of the slag slurry. As a result of C2S-CO2 chemical reaction, calcite and calcium silicate are precipitated at the surface of the oxide particles and carried between 25% and 75% of the total phosphorous, respectively. Accordingly, the mobility of the phosphorous content phase to the top of the grains serves the possibility to separate the precipitated layer by mechanical attrition process. This paper is focused on the impact of the intergrowth pattern alteration on the slag´s separability characteristics. Moreover, the operating conditions of the carbonization process, such as temperature and pressure, on the deconstruction kinetics of the C2S and the generated products will be considered. INTRODUCTION The steelmaking BOF-Slag is a stony aggregate waste from the steel manufacturing process. The investigated slag by the current research work was provided by voestalpine steelmaking plant in Linz, Austria. The current legislative situation in Austria restricts the historical application of slag as construction material, due to the high level of heavy metals content and corresponded land-filling and transportation costs of slag, therefore the demand for recycling of BOF-Slag to the steelmaking process has raised, as an alternative application. Statistically, voestalpine steelmaking plant produces about 130 kg BOF-Slag per ton of final steel product, which serves annual BOF-Slag production of 700,000 ton, approximately."

Jan 1, 2018

By B. Tora

The new method of evaluation of grindability of hard coal and its blend is shown. Standard Hardgrove test is used as a base to work out this method. The essence of this method consists of simulation of milling process in close circuit (mill-classifier) and determination of energy consumption and quantity of product under the constant feed flow. The research equipment designed specially for this project is described New method of grindability measuring completes standard Hardgrove method withdrawing its faults: ? bigger (c.a. 10 times) and more representative sample is used; ? the milling process is carried out in close circuit (similarly to the industrial condition); ? energy consumption of the milling process is determined for three samples, which differs in grain size. The new method of evaluation of grindability of hard coal and its blend is shown. Standard Hardgrove test is used as a base to work out this method. This method allows us to determine energy consumption of the milling process. The essence of this method consist of simulation of milling process in close circuit (mill-classifier) and determination of energy consumption and quantity of product under the constant feed flow. Our results will complete the Hardgrove method and will help us to better characterise coal. At the same time investigations in industrial scale are carried out. These investigations will verify this new method. Also a new mathematical model of the milling process is being elaborated. It will be used to predict behaviour of coals in industrial conditions.

Jan 1, 2014

By Shugang Hu

According to XRD, DTA and SEM detections, the hydration products of blast furnace slag (BFS) based cementing material SL, SLG. were studied in different age periods. The XRD analysis of cementing material SL hydration products showed that the composition of hydration products were mainly amorphous substances, few crystalline substances. Characteristic peak of ettringite hadn?t been found in the spectral line of DTA, and it hadn?t been found in the figures of SEM, either, which was accordant with the conclusion that the cementing performance of SL mainly coming from gel of hydrated calcium silicate (CSH) and hydrated calcium aluminate. However, the main hydration products of SLG are Aft, CSH, and AFm, which are similar to Portland cement. All results suggest that BFS is a suitable base material for cementation. Keywords: blast furnace slag, backfilling cementing material, hydration products, cementing performance

Sep 1, 2012

Deposit of Jinbaoshan platinum group metals (PGMs) ore ranks the second in Yunnan province, China. Study on process mineralogy shows that the grade of copper and nickel in the ore is just 0.16% and 0.20% respectively. Moreover, the impurities magnesium and iron and silicon are rich in the ore. The copper and nickel sulfides in the ore, especially the minerals of PGMs, are finely disseminated with the gangues like serpentine. Fine grinding is necessary, and high content of MgO in the concentrate is inevitable through traditional flotation technology on the basis of process mineralogy studies. Achievements on process mineralogy studies are applied to guide the flotation tests successfully. Progress on flotation has been made through comprehensive studies. Suitable grinding by two stages is required for the finely disseminated PGM sulphide ore to achieve the liberation of valuable minerals. Stage grinding and stage separation shall be conducted for a better recovery of valuable minerals. The oxidation state of mineral surface of sulphides has a profound effect on flotation of the ultra-fine sulphides, especially the pentlandite. The combined use of collectors enhances the selective collecting on the ultra-fine and low-grade valuable minerals, is of critical importance.

Jan 1, 2014

By Arkady Senchenko

At present, there are different traditional and modern methods for ore grindability evaluation. The correct and rational approach to sampling, testing methods and mill sizing enables one to design a workable technology. This paper contains TOMS institute experience in different grinding indices determination over the last 7 years (SAG Design Test, BWi, CWi, RWi, and other). Mill sizing examples and circuits modeling for the projects in Russia and Kazakhstan are considered. Keywords: ore grindability, SAG Design Test

Sep 1, 2012

By H. R. Manouchehri

The importance of the grinding environment and its effect on sulphide minerals flotation behavior has been known for many years. The grinding environment may play a role in controlling fine and coarse particle flotation along with dissociation of different chemical species in grinding environment. Dissociation of different chemical species and ions within the process water may result from changing the grinding environment. The mining and mineral processing industry undertakes activities that may impact on water resources. These include use and storage of chemical storm-water management, process water management, mine dewatering and management of tailings. In mineral flotation understanding and controlling water quality is paramount important not only because of its effect on flotation but also with respect to control the quality of the water which is released to the environment. Releasing of different anionic and/or cationic chemical species in the process water results from the interactions among different mineral within the ore, process water, and the milling environment. In fact grinding mill acts as an electrochemical reactor which affects the flotation performances of different value minerals as well as the quality of the tailing products. An increasing in antimony content in process/discharge water at Boliden?s Tara processing plant in Ireland to above limitation level was reported in April 2010 which needed to be controlled. An increase up to 6 times of the permitted level was reported which needed an immediate action to control due to environmental considerations. Therefore attempts were made to detect why this higher amount of Sb is released and how to control and minimize its release to the process/reclaim water. This paper discusses how/why Sb content in process/reclaim water was increased by changing the mill electrochemistry and the strategies were taken into considerations to control it. Different strategies, including electrochemical controlling of the milling section, Fenton process, using Bauxsol in treating the process water, etc., have been considered and tested which are described herein. All strategies taken into consideration for solving the problem were successful which indicated good understanding of the issue and good decision making. Furthermore, for each solution the capital and operational costs were roughly estimated. Accordingly, the Sb content in process/discharge water was controlled to a value lower than allowed limitation, i.e., 1 ppm. Keywords: antimony, water contamination, mill electrochemistry, ag milling, grinding media, eh-ph, sulfide minerals, fenton process, bauxsol, lime addition

Sep 1, 2012

By R. Venugopal

Hydrocyclones have been used extensively for more than 100 years to classify mineral slurries for recirculation in grinding circuits. Sometimes hydrocyclone classification is carried out in more than one stage to improve the efficiency of classification. Factors affecting separation efficiency include fluid velocity, density, and viscosity as well as the mass, size, and density of the particles. The geometric configuration also affects its efficiency; it includes parameters like cyclone diameter, underflow and overflow diameter, position of vortex finder, height of the cyclone, feed inlet geometry, and diameter etc. Besides changes in the basic parameters some modifications in cyclone has also been introduced from time to time which have affected its efficiency, some of these are :-(i).Introduction of magnetic force along with the centrifugal and drag force to control the flow of the magnetic particles inside the chamber.(ii). Introduction of sparger, air is introduced in the chamber in the form of bubbles, to control the flow of fine particles and hydrophobic particles. (iii). Introduction of dilution technologies for the dilution of thickened underflow. (iv).Introduction of new model. In spite of wide use and simple geometry, the real working principle of hydrocyclone chamber is extremely complex because of the swirling turbulent flow inside the device. In order to get more knowledge about hydrocyclones and to increase its efficiency, past 10-15 years simulation techniques are being developed. The simulation models also enabled a deeper insight into the static and dynamic behavior of hydrocyclones. Therefore, more emphasis on simulations by methods like Computational Fluid Dynamics (CFD), Finite Element method (FEM) is given. Overall, a status review of the work carried out on the analysis of hydrocyclone performance, modeling approaches and its contribution in the efficiency of mineral processing operation is highlighted.

Sep 1, 2012

By A. K. Suri

India plans to increase the nuclear power share in overall energy-mix to about 30% by 2032 using both indigenous and imported reactor technologies. In the immediate time-frame, it is envisaged to generate 10000 MW electricity by PHWR technology by 2020 using indigenous uranium resources. This necessitates setting-up of new uranium mills and augmenting the existing resource, mining and milling capacities. This paper describes the current status and future R & D needs towards achieving the targeted demand of yellow-cake. Keywords: uranium, hydrometallurgy, leaching, yellow cake

Sep 1, 2012

By B. Rezai

Impeller speed and air flow rate are two influence parameters on coarse particles flotation and collision and attachment angles. So, in this research recovery of quartz particles at four diameter classes carried out and collision and attachment angles investigated. It is found that maximum flotation response was observed at Impeller speed of 1100 rpm and 15 L/h air flow rate. For either more quiescent (Impeller speed<1100 rpm) or more turbulent conditions, flotation recovery decreased steadily. Furthermore, amount of attachment probabilities is calculated using suitable equation. According to this study, with decreasing particle size, air flow rate and impeller speed, probability of attachment increased and with increasing contact angle, probability of attachment increased. For various air flow rates, impeller speed and particle size, collision angle has been calculated. Maximum collision angle obtained at with 15 L/h air flow rate, particle size of 256 µm and impeller speed of 700 rpm and minimum collision angle obtained at with 45 L/h air flow rate, particle size of 545µm and impeller speed of 1300 rpm. In this study, maximum attachment angle, , was around 75 L/h air flow rate, particle size of 256 µm, contact angle of and impeller speed of 1300 rpm and minimum attachment angle was with 15 L/h air flow rate, particle size of 545 µm, contact angle of and impeller speed of 1300 rpm. ?82.72 ?64 cr??33.39 ?90 ?13.0 ?60

Jan 1, 2014

By A. P. Liu

Semi-industrial test on fine products of Meishan dressing plant was carried out with type RP80/25 high pressure roller mill produced by Homburg Corporation of Germany, and the influences of such factors as energy consumption, water containing, throughput and circulating load on rolling effect were investigated. Closed circuit experiment result showed that Meishan iron ore could be suitable for powder grinding with high pressure roller mill, and energy consumption of the operation was declined by 25%~30%, which was favorable for energy-saving, increasing production efficiency and improving grinding effects. According to above experimental results, this paper put forward the technical proposal of application of high pressure roller mill in Meishan, and pointed out some technical problems which needed to be settled urgently in technology disposal.

Jan 1, 2014

By R. Roufail

In this paper, the effect of different operating parameters of high speed stirred mill on the particle breakage mode is addressed. Morphological features of broken particles is investigated and related to the types of forces generated in the mill using Discrete Element Method (DEM). The stress intensities generated in the mill are varied by changing the agitator speed. The investigated agitator speeds were 1000, 1500, and 2000 revolution per minute (rpm). The minerals considered in this study are hard minerals (quartz) and soft, sulphide minerals (galena). The morphological features examined are roughness, roundness and elongation, which shed light on the mode of breakage during the grinding process. Particles that are rough, less round and elongated would imply that they broke via fracture, along their grain boundaries. On the other hand, the smooth, less elongated particles would mean breakage occurred across the grain, which is abrasion mod. DEM study complemented the understanding of particle breakage mechanism via tracking the types of forces applied on the particles. Normal forces imply compressive loading, which is presumed to impose fracture breakage along the grain boundaries, whereas tangential forces imply abrasion loading. Stirred mill grinding has been regarded as an attrition/abrasion process, whereas, this study showed that about 60% of total particles that are morphologically analyzed for both minerals were rough particles. Such an observation indicates that the fine product, which contain a significant amount of progeny from the coarse fractions are consistently broken via fracture. The morphology results agreed with the DEM findings, which indicated that the agitator speed, mineral type, and residence time would dictate the type and mode of particle breakage. Keywords: DEM, high speed stirred mill

Sep 1, 2012

By M. V. Sowmya

Batch biosorption experiments were carried out for the bio-remediation of Cr (VI) ions from aqueous solutions using Serratia marcescens, a Gram negative, heterotroph and Gram positive bacterial isolates from a chromite mine. The influence of various experimental parameters such as contact time, pH, concentration of Cr (VI) ions and amount of biomass was evaluated with respect to the uptake of Cr (VI). The bio-sorption of Cr (VI) was found to be quite rapid and the percentage biosortion was found to increase with increase in the equilibrium chromium concentration. The free energy of biosorption of Cr (VI) was estimated to be in the range of -23 to -25 kJ/mol for the chosen bacteria. The uptake of chromium by the bacteria was confirmed by EDX and FTIR spectroscopy. As a follow up of this study, bacterial strains resistant to hexavalent chromium were isolated from a chromite mine in Karnataka, India and identified as Arthrobacter sp., Micrococcus sp. and Exiguobacterium sp. using 16s rRNA sequencing. The efficacy of the bacterial isolates for Cr (VI) uptake was assessed and over 90% bioremoval could be achieved for Serratia marcescens and Micrococcus sp. isolate. Possible mechanisms of chromium uptake by the microorganism are discussed. Keywords: bioremediation, hexavalent chromium, biosorption, bioreduction

Sep 1, 2012

By W. M. Zeng

A mixed culture of moderately thermophilic microorganisms was enriched from Acid Mine Drainage (AMD) samples collected from several chalcopyrite mines in China,which can leach copper from chalcopyrite effectively. Its tolerance to chalcopyrite was brought up to 80 g/L after being adapted to gradually increased concentrations of chalcopyrite. The effects of several leaching variables on copper recovery in Stirred Tank Reactor had been investigated. The ore contained chalcopyrite (62.2%) and galena (25.6%) as the main sulfide minerals. The results of the tests show that it is possible, operating at 8% of pulp density to attain copper extraction of 75% in 44 days. The leaching rate of chalcopyrite tends to increase with the dissolution of total iron. Microscopic counts of microorganisms in the solution tend to be higher at low pH range. Furthermore, the analyses of leached residues indicate that the passivation of this chalcopyrite is mainly due to the formation of a mass of jarosite and anglesite (about 48.3% and 21.7% in residue respectively), other than elemental sulphur layer. The bacterial community composition was analyzed by using amplified ribosomal DNA restriction analysis (ARDRA). Two moderately thermophilic bacteria species were identified as Leptospi-rillum ferriphilum and Acidithiobacillus caldus, with different proportion in the bio-pulp, 67% and 33%, respectively.

Jan 1, 2014

By J. Wiese, K. Corin, Z. Song

"Relating flotation performance to the electrochemical characteristics of a pulp is complex both in fundamental research and in practice. In the case of thiol collectors, different Eh values in the flotation system can result in the formation of the dimer or the metal thiolate which may or may not enhance the hydrophobicity of the mineral. Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, are usually manipulated to achieve an optimum flotation response by control of pH and dissolved oxygen levels in the system. A variation in pulp potential may also be achieved by the addition of potential modifiers such as sodium hydrosulphide (NaHS), sodium hypochlorite (NaClO) or hydrogen peroxide (H2O2). There exists anecdotal evidence which suggests that the addition of small amounts of H2O2 to the flotation process can improve sulphide mineral recovery. The objective of the present study was to investigate the effect of the addition of the potential modifier, H2O2, on sulphide mineral recoveries and grades in the flotation of sulphide minerals from two copper bearing ores from China and compare the results to those obtained for a PGM bearing ore South Africa. Batch flotation tests were conducted using the three different ores at the natural pH of the different systems, in the presence of a xanthate collector and the absence and presence of H2O2 as a potential modifier. The results indicate that the addition of carefully controlled low concentrations of H2O2 resulted in improvements in flotation performance. INTRODUCTIONElectrochemical potential as a control parameter in the flotation of sulphide minerals has been widely studied (Allison et al., 1972; Gardner and Woods, 1979; Ross and Van Deventer, 1985; Chander, 2003; Woods, 2003; Javadi, 2013). There is concensus that in order to be recovered during flotation, sulphide minerals require a suitable redox environment. During the flotation process thiol collectors and sulphide minerals are involved in electrochemical reactions which result in the formation of hydrophobic species at the mineral surface (Finkelstein and Goold, 1972; Rand and Woods, 1984). Sulphide minerals act as semiconductors and electrons are transferred during the interaction of the mineral with collector. The resultant potential difference and its magnitude are responsible for the transfer of electrons and the rate of the reaction (Bard and Faulkner, 2001; Fuerstenau et al., 2007). Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, may be manipulated to achieve an optimum flotation response by control of pH and dissolved oxygen levels in the system (Heyes and Trahar, 1979). The use of potential modifiers viz. reducing or oxidizing agents which include H2O2, NaClO, and NaHS, is an alternative method by which to control the potential of the pulp in a flotation system which may or may not promote the flotation of desired minerals (Rao, 2004). The oxidizing agent, H2O2, undergoes a cathodic reaction which can result in the enhanced flotation of valuable minerals. The potential of the system is increased which results in a shift in the mixed potential of a mineral. The magnitude of the over-potential influences the rate of the oxidation process and thus the flotation response of sulphide minerals (Kocabag and Guler, 2008). Equation 1 shows the proposed oxidation of xanthate by H2O2 (Lipkina and Streltysn, 1970)."

Jan 1, 2018

By E. Alldén Öberg

In 2004, LKAB decided to start a basic engineering study in expanding its existing production lines at the Malmberget mine site. It was expected that some of the production lines would become bottlenecks with reference to capacity. In this study, the sorting plant is examined and the results show that several unit operations will be limiting under current operating conditions. An additional purpose with the study was to investigate how replacement of some machines would influence performance and if production plans for the coming years might be achieved. Steady-state simulations using the software Modsim? were extensively used to study process performance for different operating conditions, such as iron content and size distribution in run-of-mine ore. Model parameters were derived from pilot plant data and when possible from ex-isting circuits. A complication for the simulations was the lack of relevant data and therefore some of the initial results were only indicative. The result shows that installation of new screens would give a much better operation, but also new crushers would be an improvement. This, since they can be run with full crusher chamber and tighter CSS. During 2007, most of the proposed remedies were implemented and the result is that the bottle-necks are gone, and the grades and material balances are even better than what was envisioned from the simulations.

Jan 1, 2014